Most of the information we have about the sc eeprom comes from graf_chokolo reverse engineering of the HV see Hypervisor Reverse Engineering

Here is where system flags, tokens and hashes are stored.

Right now most of the communication we have with the sc eeprom is through Linux using graf_chokolo ps3dm-utils and/or using his payloads.

See also Discussion page and Zer0Tolerance

SC EEPROM Info

SC EEPROM from fat consoles is a custom/proprietary EEPROM chip that uses a special non standard commands to read/write from EEPROM. We are so lucky that Sony had exposed EEROM chip legs out of Syscon, so we have a physical access to it and we could attach devices like "Logic Analyzer", "Protocol Analyzer", "Custom made MCU boards" to capture traffic between console and Syscon EEPROM.

For FAT console Syscon EEPROM consists of: 0x4000 blocks, and every block is consists of 2 bytes of data. So the total EEPROM size is: 0x8000 byte length.

And since the pin-out of Syscon chip for Slim & Super Slim consoles is not known till now, we can not be sure if the Syscon EEPROM pins are exposed outside or not so we can access it like in FAT console without handling Syscon it self.

SC EEPROM Commands

FAT console's SC EEPROM used a standard SPI protocol with a proprietary commands as flow:

Description	Command	Note
Unlock Command	0xA3 0x00 0x00	This command must be send first before write command.
Write Command	0xA4 0xXX 0xXX	XX XX is a block id to be written (value 0x0000 to 0x3FFF), the maximum data to be written in one command cycle is 32 byte length (16 blocks).
Read Command	0xA8 0xXX 0xXX	XX XX is a block id to be read (value 0x0000 to 0x3FFF), there is no maximum limit for read command so we can send it once with block id 0x00 0x00 then read the full EEPROM at once without sending read command again.
Check Status Command	0xA9 0x00 0x00 0x00	The response of this command is 0xFFFFFFFF if there is no error, or any other value if there is error happened or EEPROM still busy doing something.

SC EEPROM dumps

https://mega.nz/#!iV0nGY4I!94ByAd-sourgK8_l_4s-6BX_V7iVOrysQd55bI0N6ws MD5:1DB1CAA8E3D54256A59D08B6AF2B9BC5 (Dumped by Syscon EEPROM Flasher done by me "Abkarino" using Arduino Mega).

https://mega.nz/#!AwF1jIaB!5qei9JOCzisgUHARcjARCw0zvQENkkvtAdd_O0dRUfI DECR eeprom dump from lv2 um_manager, needs documentation.

different consoles, same initial 16 bytes. maybe key/iv?

Important Offsets

EEPROM Offset Table - Flags and Tokens

Here is the table of EEPROM offsets that can be accessed through Update Manager (3.15):

Offset	Size	Description
0x02F00	8	Downgrade Minimum Version String
0x02F08	0x10	Downgrade Minimum Version Build + Date Build String
0x02F20	8	Target ID? (HV bible lists the Target ID as 85 Europe, not 83 Japan)
0x02F28	0xD0	Padding/undocumented 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF xx xx xx xx xx FF FF xx xx xx xx xx xx xx xx xx xx xx xx xx 00 00 00 00 FF xx 00 xx xx FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF xx xx xx 00 00 xx xx xx xx xx FF FF FF xx xx xx FF FF FF xx 00
0x02FF8	1	Factory Bit (0 = ?, 1 = reset, 2 = ?, 3 = (on retails))
0x02FF9	0x7	Padding/undocumented 00 00 00 00 xx xx xx

Offset		Size	Description
0x48000		0x13	(lv0 NVS region 0 start)
0	0x48000	0x13	(lv0 NVS region 0)
0x48012		-	(lv0 NVS region 0 end)
0x48013		0x2A	QA Token ECDSA Signature (=> 3.60 firmwares)
0x48800		0x0C	(lv0 NVS region 1 start)
1	0x48801	0xFF	- hv log settings/infos? -
	0x48802	1
	0x48804	4	bootrom failure code
	0x48808	4	bootrom failure timestamp
0x4880B		-	(lv0 NVS region 1 end)
0x48C00		0x20	(lv0 NVS region 2 start)
2	0x48C00	1	load_image_in_rom flag (os_boot_order_flag)
	0x48C01	1	(force standalone mode related)
	0x48C02	1	debug interface (select_net_device)
	0x48C03	1	sys.dbgcard.dgbe.index (select_dgbe_device)
	0x48C05	1	update_flag for CEB
	0x48C06	1	FSELF Control Flag / toggles release mode (fself_ctrl)
	0x48C07	1	Product Mode (UM allows to read this offset, it can be also written but only when already in product mode)
	0x48C08	1	(UNKNOWN ?debug?))
	0x48C0A	1	QA Flag
	0x48C0B	1	mode_auth_flag / gx enable
	0x48C0C	1	bootrom diagnostic mode and parameter
	0x48C0D	1
	0x48C0F	2
	0x48C11	1	bootrom trace level (0x00: fatal errors, 0x01: errors, 0x02: information messages, 0x03: debug messages)
	0x48C12	1
	0x48C13	1	Device Type (flash_ext_format)
	0x48C14	?	cellos_spu_configure
	0x48C18	4	System Language XRegistry.sys#Settings ( /setting/system/language )
	0x48C1C	4	VSH Target (seems it can be 0xFFFFFFFE, 0xFFFFFFFF, 0x00000001 default: 0x00000000 /maybe QA,Debug,Retail,Kiosk?)
0x48C1F		-	(lv0 NVS region 2 end)
0x48C22		0x03	(lv0 NVS region 3 start)
3	0x48C22	1	be nclk (be_nclck_flag1)
	0x48C23	1	be ref clk (be_nclck_flag2)
	0x48C24	1	Bank #0 OS-Flag (ros0 if 0xFF else ros1) (os_bank_indicator)
0x48C24		-	(lv0 NVS region 3 end)
0x48C25		1	Bank #0 rvkprg-Flag
0x48C26		1	Bank #0 rvkpkg-Flag
0x48C27		1	Bank #1 OS-Flag
0x48C28		1	Bank #1 rvkprg-Flag
0x48C29		1	Bank #1 rvkpkg-Flag
0x48C30		0x0D	(lv0 NVS region 4 start)
4	0x48C30	1	SPE number Usally 0x06, can be set to 0x07 to enable the 8 SPE (restrict_spu)
	0x48C31	4	sata_param
	0x48C35	8	spr_tbuw_value (cellos_spu_configure)
0x48C3C		-	(lv0 NVS region 4 end)
0x48C40		0x10	(lv0 NVS region 5 start)
5	0x48C42	1	HDD Copy Mode
	0x48C43	4
	0x48C47	1	Analog Sunset Flag, will disable AACS video output without HDMI cable soon
	0x48C50	0x10	Debug Support Flag
	0x48C60	1	Update Status
	0x48C61	1	Recover Mode Flag
	0x48C62	8	boot param
	0x48C6A	2	factory process completion %
0x48C4F		-	(lv0 NVS region 5 end)
0x48C80		0x10	(lv0 NVS region 6 start)
6	0x48C80	8	(rsx.rdcy.0)
6	0x48C88	8	(rsx.rdcy.1)
0x48C8F		-	(lv0 NVS region 6 end)
0x48C90		0x30	(lv0 NVS region 7 start)
7	0x48C90	8	(rsx.rdcy.2)
	0x48C98	8	(rsx.rdcy.3)
	0x48CA0	8	(rsx.rdcy.4)
	0x48CA8	8	(rsx.rdcy.5)
	0x48CB0	8	(rsx.rdcy.6) / game_board_storage_read
	0x48CB8	8	(rsx.rdcy.7) / game_board_storage_read
0x48CBF		-	(lv0 NVS region 7 end)
0x48CCE		1	0xFF / 0xFE / 0x00 (?)
0x48CCF		1	pme_user debug printf flag ( & 0x03 )
0x48CF0		0x10	(NVS region start)
	0x48CF0	1	ss.common.printf.enabled
	0x48CF1
	0x48CF2
	0x48CF3
	0x48CF4
	0x48CF5
	0x48CF6
	0x48CF7
	0x48CF8
	0x48CF9
	0x48CFA
	0x48CFB
	0x48CFC
	0x48CFD
	0x48CFE
	0x48CFF
0x48CFF		-	(NVS region end)
0x48D00		0x0C	(lv0 NVS region 8 start)
8	0x48D00	4	ip_addr (dgbe_config)
	0x48D04	4	ip_netmask
	0x48D08	4	ip_gateway
0x48D0B		-	(lv0 NVS region 8 end)
0x48D20		0x08	(lv0 NVS region 9 start)
9	0x48D20	8	spider.gbe0.macaddr.0 (`0xFFFFFFFFFFFFFFFF` if unused/nonpresent)
0x48D27		-	(lv0 NVS region 9 end)
0x48D28		0x18	(lv0 NVS region B start)
B	0x48D28	8	spider.gbe0.macaddr.1 (`FFFFFFFFFFFFFFFF` if unused/nonpresent)
	0x48D30	8	spider.gbe0.macaddr.2 (`FFFFFFFFFFFFFFFF` if unused/nonpresent)
	0x48D38	8	spider.gbe0.macaddr.3 (`FFFFFFFFFFFFFFFF` if unused/nonpresent)
0x48D3F		-	(lv0 NVS region B end)
0x48D3E		0x50	(lv0 NVS region A start)
A	0x48D3E	0x50	QA Token - UM doesn't allow access to this offset but SC Manager can read/write it (qa_token)
0x48D8D		-	(lv0 NVS region A end)
0x48D8E		0x50	mode_auth_data (read/cleared by ss_sc_init_pu, checked by spu_mode_auth)

In a standard mostly untouched ps3 the common value for this flags is 0xFF wich means not active, anything else means active (e.g. 0xFE)

To change this to an active status you have to write 0x00 to turn on the flag

Debug support flag is tied to EID which is supposed to be hashed and saves in SC EEPROM

QA flag is tied to QA token that is also saved in this part of the SC EEPROM

QA Token ECDSA Signature is stored in 0x48013 offset (starting from 3.60 firmwares)

Undocumented config

There is an unknown syscon response of 0x100 bytes when using NVS service with such params: BlockID=1, Offset=0, Size=0.

0000h: FF 02 FF FE FF 02 FF FF 19 FB E1 16 00 00 00 00  ÿ.ÿþÿ.ÿÿ.ûá..... 
0010h: 17 74 B8 54 00 00 E1 18 00 04 00 00 0C 03 00 00  .t¸T..á......... 
0020h: 3C 02 02 00 00 00 00 10 00 00 00 00 55 55 55 55  <...........UUUU 
0030h: 00 00 00 00 00 00 00 00 17 E0 C8 52 00 00 E2 18  .........àÈR..â. 
0040h: 01 50 00 35 40 01 03 00 00 00 00 10 1D 30 00 B3  [email protected].³ 
0050h: 00 07 01 00 00 00 00 00 00 00 00 00 00 00 00 00  ................ 
0060h: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF  ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ 
0070h: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF  ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ 
0080h: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF  ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ 
0090h: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF  ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ 
00A0h: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF  ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ 
00B0h: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF  ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ 
00C0h: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF  ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ 
00D0h: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF  ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ 
00E0h: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF  ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ 
00F0h: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF  ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ

This is 0x48800 on EEPROM

cech-c (NO BD Drive): http://pastie.org/private/grl0dc0dxajisa36chgm7w

lv0 SC EEPROM usage

[*] lv0 NVS regions:
	# start_offset end_offset block   size
	0 0x00         0x12       0x48000 0x13
	1 0x00         0x0B       0x48800 0x0C
	2 0x00         0x1F       0x48C00 0x20
	3 0x22         0x24       0x48C00 0x03
	4 0x30         0x3C       0x48C00 0x0D
	5 0x40         0x4F       0x48C00 0x10
	6 0x80         0x8F       0x48C00 0x10
	7 0x90         0xBF       0x48C00 0x30
	8 0x00         0x0B       0x48D00 0x0C
	9 0x20         0x27       0x48D00 0x08
	A 0x3E         0x8D       0x48D00 0x50
	B 0x28         0x3F       0x48D00 0x18

[*] Example region data (taken from region cache):
	2:
	   01 FF 05 FF FF FF FF FF FF FF 00 FF FF FF FF FF
	   FF FF FF FE FF FF FF FF 00 00 00 01 00 00 00 00
	3:
	   FF FF 00
	4:
	   06 18 18 17 18 FF FF FF FF FF FF FF FF
	5:
	   FF FF 0D 02 0A 02 FF FF FF FF FF FF FF FF FF FF
	9:
	   FF FF FF FF FF FF FF FF

[*] lv0 SC EEPROM usage:
	name                 addr    size structure
	dgbe_config          0x48D00 0x0C [0x04 ip_addr, 0x04 ip_netmask, 0x04 ip_gateway]
	restrict_spu         0x48C30 0x01 [0x01 flag]
	sata_param           0x48C31 0x04 [0x04 flag]
	os_bank_indicator    0x48C24 0x01 [0x01 flag]
	cellos_spu_configure 0x48C33 0x04 [0x04 config]
	flash_ext_format     0x48C13 0x01 [0x01 flag]
	cellos_flags         0x48C0F 0x02 [0x02 flags]
	qaf_enable           0x48C0A 0x01 [0x01 flag]
	UNKNOWN (debug?)     0x48C08 0x01 [0x01 flag]
	fself_ctrl           0x48C06 0x01 [0x01 flag]
	select_dgbe_device   0x48C03 0x01 [0x01 index]
	os_boot_order_flag   0x48C00 0x01 [0x01 flag]
	qa_token             0x48D3E 0x50 [0x50 token]
	UNKNOWN              0x48804 0x04 [0x04 value]
	UNKNOWN              0x48D20 0x08 [0x08 value]
	rsx.rdcy.7           0x48CB8 0x08 [0x08 value]
	rsx.rdcy.6           0x48CB0 0x08 [0x08 value]
	rsx.rdcy.5           0x48CA8 0x08 [0x08 value]
	rsx.rdcy.4           0x48CA0 0x08 [0x08 value]
	rsx.rdcy.3           0x48C98 0x08 [0x08 value]
	rsx.rdcy.2           0x48C90 0x08 [0x08 value]
	rsx.rdcy.1           0x48C88 0x08 [0x08 value]
	rsx.rdcy.0           0x48C80 0x08 [0x08 value]
	be_nclck_flag2       0x48C23 0x01 [0x01 flag]
	be_nclck_flag1       0x48C22 0x01 [0x01 flag]
	select_net_device    0x48C02 0x01 [0x01 index]
	spr_tbuw_value       0x48C35 0x08 [0x08 value]
	bootrom_trace_level  0x48C11 0x01 [0x01 level]

System Data From EEPROM

Here is the list of possible EEPROM offsets:

Index	SC EEPROM Offset	Size Of Data	Description
0	0x48D20	6	?
1	0x48D28	6	?
2	0x48D30	6	?
3	0x48D38	6	?
4	0x48D00	4	?
5	0x48D04	4	?
6	0x48D08	4	?

Dumpable EEPROM Offset - Block ID and Block Offset Mapping Table (NVS Service)

Right now we only have read access to some portions of the eeprom to have access to this regions DM needs to be patched, see section dumping eeprom

EEPROM Offset	Block ID	Block Offset	Description	Physical Offset
0x48000 - 0x480FF	0x00	0x48000 - 0x480FF	?	0x7000
0x48800 - 0x488FF	0x01	0x48800 - 0x488FF	Bluray Drive Area	0x7100
0x48C00 - 0x48CFF	0x02	0x48C00 - 0x48CFF	Contains flags and tokens/ see above	0x7200
0x48D00 - 0x48DFF	0x03	0x48D00 - 0x48DFF	System Data Region	0x7300
0x2F00 - 0x2FFF	0x10	0x2F00 - 0x2FFF	"Industry Area" aka OS Version Area	0x2F00
0x3000 - 0x30FF	0x20	0x3000 - 0x30FF	"CS Area"	0x3000
All other offsets	Invalid	Invalid	?

Dumpable only with HW flasher EEPROM Offsets - Full Mapping Table (NAND Only)

Physical Offset	Description
0x0-0xF	magic1? (static bytes)
0x10-0x29F	eEID1? (probably encrypted)
0x560-0x95F	Authenticated Data Region 0
0x960-0xD5F	Authenticated Data Region 1
0xD60-0x115F	Authenticated Data Region 2
0x1160-0x155F	Authenticated Data Region 3
0x1560-0x195F	Authenticated Data Region 4
0x1960-0x1D5F	Authenticated Data Region 5
0x1D60-0x215F	Authenticated Data Region 6
0x2160-0x255F	Authenticated Data Region 7
0x2700 - 0x270F	magic2? (static bytes)
0x2800 - 0x2BFF	Syscon Patch Content Top-Half
0x4400 - 0x4FFF OR 0x7400 - 0x7FFF	Syscon Patch Content Bottom-Half
All other offsets	Unknown

Authenticated Data Regions Crypto Analysis

Tests

http://i.imgur.com/A8g00bD.png <- aes 128 cbc with fixed key and incremented iv (by 1 each time)
http://i.imgur.com/HZDWGSk.png <- results
http://i.imgur.com/2mtrtdm.png region 0 encrypted vs http://i.imgur.com/7bSdQni.png decrypted
http://i.imgur.com/FGJKkuz.png region 7 encrypted vs http://i.imgur.com/7TSeHWK.png decrypted

Conclusion

different key for a different authenticated region.
sony uses either aes 128-cbc or aes 256-cbc (most likely 128-cbc)
sony does this weird cbc crypto in which they only decrypt portions of 0x10 bytes of the region, then increment or decrement (most likely increment) iv, and then decrypt again. i've decided to call it ctr-cbc
most likely the keys used are ~~session~~ perconsole keys.
most likely the iv used starts with 00, then gets incremented by 1 for each 0x10 bytes

Acknowledgements

Zer0Tolerance for the crypto findings
flatz for his awesome syscon tool

Dumping your SC EEPROM

Linux

First you need graf_chokolo kernel ps3dm-utils and linux_hv_scripts.

If you are ready.

Patch DM using linux_hv_scripts

dmpatch.sh

Read the data from the region you want for example (see tables above)

ps3dm_scm /dev/ps3dmproxy 0x48000 0xFF

You can see some coolstuff that containing dumps

Hashes

Where exactly the hashes are stored is still a secret, it is said that those hashes are stored in SC EEPROM

To retrieve the information about the packages you have installed you can also use ps3d_utils

Linux

Installed Package info

ps3dm_um /dev/ps3dmproxy get_pkg_info TYPE

Examples

get_pkg_info 1 - Core OS package

	
		0003004100000000

get_pkg_info 2 - Revoke List for program

	
		0003004100000000

get_pkg_info 3 - Revoke list for package

		0002003000000000

get_pkg_info 4

		deadbeaffacebabe

get_pkg_info 5

		deadbeaffacebabe

get_pkg_info 6 - Firmware Package

		0003005000000000

You can find more information about this in Hypervisor Reverse Engineering

Hashes

What algorithm is used and what exactly is hashed is still unknown (seems that the content of files is hashed by the SHA-1).

ps3dm_scm /dev/ps3dmproxy get_region_data ID

These hashes are checked by lv1 to make sure that the data has not been altered through SC Manager: scm_get_region_data: get_result: ret[X]: 0x%x

Examples

region_data 0 - Core OS package

00 03 00 41 00 00 00 00 00 c3 eb 01 96 24 d0 1c 26 14 f3 1c a4 a2 ff ce 81 77 3a 4c f8 42 86 04 ee 34 bb db be 1c a7 51 e5 59 f1 95 61 07 a5 eb

region_data 1

	
ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff

region_data 2

	
ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff

region_data 3 //Revoke List for program?

	
00 03 00 41 00 00 00 00 80 41 f6 b8 f2 d5 30 60 59 35 49 d7 f0 3d 58 57 87 00 88 11 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff

region_data 4

	
ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff

region_data 5 //Revoke List for package?

		
00 02 00 30 00 00 00 00 ba 6e 1c d5 5f 48 5b 8b 3f cc c8 60 75 ce f6 83 b2 20 dc f4 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

region_data 6

	
de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be

region_data 7

de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be

region_data 8 - BD Firmware Package

	
00 03 00 50 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

region_data 9

de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be

region_data 10

	
de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be

region_data 11

de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be

region_data 12

de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be

region_data 13

de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be

region_data 14

de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be

region_data 15

de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be

region_data 16 - 47?

Dumped data(SLIM)

Here is an example of data (partition 1) from syscon which stores VTRM block key, SRK/SRH, region data, etc.

0x0000: 00 00 00 03 C0 00 00 FF 00 00 00 00 00 00 00 00  ................ 
0x0010: 01 A2 F6 6C 26 54 1A 54 CE A3 F9 71 50 2B A8 20  ...l&T.T...qP+.  
0x0020: 33 0E F4 5F 77 19 96 A6 7A 84 5D C9 AE B9 50 73  3.._w...z.]...Ps 
0x0030: AE 45 5D 8E 6C BB 80 4D 7E C5 BF A4 AC 8E E1 E5  .E].l..M~....... 
0x0040: 82 9B 0A 57 9A 40 D9 0C 00 00 00 00 00 00 00 00  ...W.@.......... 
0x0050: 7F 03 00 94 B4 7C B6 50 51 E5 84 30 4D 51 77 7C  ?....|.PQ..0MQw| 
0x0060: 7C 03 00 94 B4 7C B6 50 51 E5 84 30 4D 51 77 7C  |....|.PQ..0MQw| 
0x0070: 7D 03 00 94 B4 7C B6 50 51 E5 84 30 4D 51 77 7C  }....|.PQ..0MQw| 
0x0080: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF  ................ 
0x0090: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF  ................ 
0x00A0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF  ................ 
0x00B0: 00 03 00 55 00 00 00 00 50 12 F0 AD 3A 4F 9F 1B  ...U....P...:O.. 
0x00C0: F9 F1 E1 D3 64 85 D4 01 19 9D 76 9E 5C 33 8D FE  ....d.....v.\3.. 
0x00D0: 39 75 10 9B 73 43 69 89 2B F6 EE 53 15 4A 3B 06  9u..sCi.+..S.J;. 
0x00E0: 00 03 00 55 00 00 00 00 7B C9 65 97 CF 0D 20 4B  ...U....{.e... K 
0x00F0: BB 6A B1 B9 B0 71 83 27 79 6F 16 08 FF FF FF FF  .j...q.'yo......
------------------------------------------------------------------------- 
0x0100: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF  ................ 
0x0110: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF  ................ 
0x0120: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF  ................ 
0x0130: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF  ................ 
0x0140: 00 01 00 00 00 00 00 00 B0 64 53 92 7F 5E 29 47  .........dS.?^)G 
0x0150: 9C BC 84 58 4A F2 ED 0B 50 E1 BE F3 FF FF FF FF  ...XJ...P....... 
0x0160: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF  ................ 
0x0170: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF  ................ 
0x0180: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF  ................ 
0x0190: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF  ................ 
0x01A0: DE AD BE AF FA CE BA BE DE AD BE AF FA CE BA BE  ................ 
0x01B0: DE AD BE AF FA CE BA BE DE AD BE AF FA CE BA BE  ................ 
0x01C0: DE AD BE AF FA CE BA BE DE AD BE AF FA CE BA BE  ................ 
0x01D0: DE AD BE AF FA CE BA BE DE AD BE AF FA CE BA BE  ................ 
0x01E0: DE AD BE AF FA CE BA BE DE AD BE AF FA CE BA BE  ................ 
0x01F0: DE AD BE AF FA CE BA BE DE AD BE AF FA CE BA BE  ................
------------------------------------------------------------------------- 
0x0200: 00 03 00 50 00 00 00 00 00 00 00 00 00 00 00 00  ...P............ 
0x0210: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................ 
0x0220: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................ 
0x0230: DE AD BE AF FA CE BA BE DE AD BE AF FA CE BA BE  ................ 
0x0240: DE AD BE AF FA CE BA BE DE AD BE AF FA CE BA BE  ................ 
0x0250: DE AD BE AF FA CE BA BE DE AD BE AF FA CE BA BE  ................ 
0x0260: DE AD BE AF FA CE BA BE DE AD BE AF FA CE BA BE  ................ 
0x0270: DE AD BE AF FA CE BA BE DE AD BE AF FA CE BA BE  ................ 
0x0280: DE AD BE AF FA CE BA BE DE AD BE AF FA CE BA BE  ................ 
0x0290: DE AD BE AF FA CE BA BE DE AD BE AF FA CE BA BE  ................ 
0x02A0: DE AD BE AF FA CE BA BE DE AD BE AF FA CE BA BE  ................ 
0x02B0: DE AD BE AF FA CE BA BE DE AD BE AF FA CE BA BE  ................ 
0x02C0: DE AD BE AF FA CE BA BE DE AD BE AF FA CE BA BE  ................ 
0x02D0: DE AD BE AF FA CE BA BE DE AD BE AF FA CE BA BE  ................ 
0x02E0: DE AD BE AF FA CE BA BE DE AD BE AF FA CE BA BE  ................ 
0x02F0: DE AD BE AF FA CE BA BE DE AD BE AF FA CE BA BE  ................
------------------------------------------------------------------------- 
0x0300: DE AD BE AF FA CE BA BE DE AD BE AF FA CE BA BE  ................ 
0x0310: DE AD BE AF FA CE BA BE DE AD BE AF FA CE BA BE  ................ 
0x0320: DE AD BE AF FA CE BA BE DE AD BE AF FA CE BA BE  ................ 
0x0330: DE AD BE AF FA CE BA BE DE AD BE AF FA CE BA BE  ................ 
0x0340: DE AD BE AF FA CE BA BE DE AD BE AF FA CE BA BE  ................ 
0x0350: DE AD BE AF FA CE BA BE DE AD BE AF FA CE BA BE  ................ 
0x0360: DE AD BE AF FA CE BA BE DE AD BE AF FA CE BA BE  ................ 
0x0370: DE AD BE AF FA CE BA BE DE AD BE AF FA CE BA BE  ................ 
0x0380: 42 03 00 94 B4 7C B6 50 51 E5 84 30 4D 51 77 7C  B....|.PQ..0MQw| 
0x0390: 43 03 00 94 B4 7C B6 50 51 E5 84 30 4D 51 77 7C  C....|.PQ..0MQw| 
0x03A0: 40 03 00 94 B4 7C B6 50 51 E5 84 30 4D 51 77 7C  @....|.PQ..0MQw| 
0x03B0: 41 03 00 94 B4 7C B6 50 51 E5 84 30 4D 51 77 7C  A....|.PQ..0MQw| 
0x03C0: 46 03 00 94 B4 7C B6 50 51 E5 84 30 4D 51 77 7C  F....|.PQ..0MQw| 
0x03D0: 47 03 00 94 B4 7C B6 50 51 E5 84 30 4D 51 77 7C  G....|.PQ..0MQw| 
0x03E0: 44 03 00 94 B4 7C B6 50 51 E5 84 30 4D 51 77 7C  D....|.PQ..0MQw| 
0x03F0: 45 03 00 94 B4 7C B6 50 51 E5 84 30 4D 51 77 7C  E....|.PQ..0MQw|

=Dumped data (DECR)=´

0000000 0000 0200 00c0 ff00 0000 0000 0000 0000
0000010 49eb 4a35 26c3 7a51 881e 5dc9 0352 54f1
0000020 d07c 8877 1bd1 a213 dd43 24c7 79a4 d15c
0000030 b93f c1f3 0ae9 4328 d830 82e0 6e20 2906
0000040 aaee d04c 44ac 7edd 0000 0000 0000 0000
0000050 579d 03cf ebe0 7a89 828f d63b f583 1dfb
0000060 b6f5 d336 d548 2056 b987 fd3a 493b 71ab
0000070 4008 b533 0740 b884 3f73 91d1 3e04 e81b
0000080 0300 1500 0000 0000 8f39 3b56 c3d3 2719
0000090 f542 2a0b 0d06 6431 f318 8ae3 ab0a bed0
00000a0 d7f0 7a47 f4a7 5ba7 092d 4878 46e9 6240
00000b0 0400 7800 0000 0000 009f b7c1 85ba f09b
00000c0 2f54 07b8 2e3a c4b7 d048 6d4b 10c8 994b
00000d0 1eec 9db0 a3e9 04b4 9def b07d 2483 7369
00000e0 0300 5500 0000 0000 02e9 49a0 20ca 495d
00000f0 6546 86fe b4cf 1e3b 0045 046e ffff ffff
0000100 ffff ffff ffff ffff ffff ffff ffff ffff
0000110 0300 1500 0000 0000 c204 3714 9009 3bc3
0000120 e024 2c8c 93d8 a514 5879 5190 ffff ffff
0000130 ffff ffff ffff ffff ffff ffff ffff ffff
0000140 0100 0000 0000 0000 020f f032 094c bc59
0000150 c101 761c 2e77 a4e0 c180 2feb ffff ffff
0000160 ffff ffff ffff ffff ffff ffff ffff ffff
0000170 0100 0000 0000 0000 b233 a494 e16b 7449
0000180 5fcc 48ee ae19 763c d2cd db7d ffff ffff
0000190 ffff ffff ffff ffff ffff ffff ffff ffff
00001a0 adde afbe cefa beba 0000 0000 0000 0000
00001b0 b01f f2c8 e555 441a eb3a 5177 f415 252f
00001c0 b091 2b3a 7943 cac8 5e59 8c3c f5b9 5495
00001d0 0100 0000 0106 0000 0000 0000 0000 0000
00001e0 0000 0000 0000 0000 0000 0000 0000 0000
*
0000200 0300 1000 0000 0000 0000 0000 0000 0000
0000210 0000 0000 0000 0000 0000 0000 0000 0000
*
0000230 adde afbe cefa beba 0000 0000 0000 0000
0000240 5bd5 81f0 fa49 0b71 5899 edd3 3ed5 9630
0000250 9759 bfb2 6229 86e7 6fde 1c67 198e 87e1
0000260 adde afbe cefa beba 0000 0000 0000 0000
0000270 2bc7 313f 3b5d b760 c6a0 38f5 d740 04a0
0000280 562c 01df ad6f 2635 9eac 52b1 4e97 e84d
0000290 adde afbe cefa beba 0000 0000 0000 0000
00002a0 84f0 e07f de42 af21 b958 11a4 d003 a8ff
00002b0 9de3 2554 dd28 467d 2420 ef43 a33a aa9e
00002c0 adde afbe cefa beba 0000 0000 0000 0000
00002d0 6eff 37f8 2f55 e07a 5362 bed4 d0d1 38e1
00002e0 8235 de2d d7a6 d4ed f6a7 957d b84f a641
00002f0 adde afbe cefa beba 0000 0000 0000 0000
0000300 017f 783c 9a0b df98 137d efce c4ef e934
0000310 137c e3d5 85ff a90b b81d 0eb3 63f4 48d9
0000320 adde afbe cefa beba 0000 0000 0000 0000
0000330 4f8e e7c0 a9c9 14da 2d2b 2dad 484e 5bf5
0000340 ca06 e65a 457b 45e1 c6a5 a6b1 8ea5 49d5
0000350 adde afbe cefa beba 0000 0000 0000 0000
0000360 e9c4 9aa3 7cec 9736 4f25 3de4 73ea 6398
0000370 177c 570a 44ed 0870 b06a 3a9e f2c4 b5cc
0000380 7c49 745c 7545 c566 7407 664b 8458 d842
0000390 71cb a8a4 557e 64e7 24b3 474f 61aa 3231
00003a0 f850 edc1 7a64 0a3b f640 a190 538e 7165
00003b0 8714 9574 14ef 4048 28e7 7451 d242 8237
00003c0 f278 9ed8 6406 4971 6520 f968 79e0 38f7
00003d0 1b6f 6d9e 58bc aeeb 433f 4983 0bb0 f413
00003e0 7b1d 9a48 a3f1 22fb 006e 757a e3d8 47c7
00003f0 0e0e ec8a 5343 654a 8b19 4985 9be0 fe15

0000000 0000 0200 00c0 ff00 0000 0000 0000 0000
0000010 68b4 7f3b 57ad 0f3f a223 e8a1 4911 f5f4
0000020 c928 9f3e f814 f92e 49c1 46cd a06c af0e
0000030 1974 b2b8 9211 f6d0 0c69 5aa6 36e0 1815
0000040 5227 5f89 59cf 2842 0000 0000 0000 0000
0000050 9d14 1e2f 07c8 77f8 e992 cee4 1200 9aa0
0000060 cfad 9941 d3f9 83ec 8f2c 8026 c0d4 0efb
0000070 a3b3 ea61 419a cf17 50e8 d215 a359 dc51
0000080 0300 1500 0000 0000 8f39 3b56 c3d3 2719
0000090 f542 2a0b 0d06 6431 f318 8ae3 ab0a bed0
00000a0 d7f0 7a47 f4a7 5ba7 092d 4878 46e9 6240
00000b0 0300 1500 0000 0000 8f39 3b56 c3d3 2719
00000c0 f542 2a0b 0d06 6431 f318 8ae3 d405 7915
00000d0 68f7 df8a 9ead 34cd c7b4 a89f 99c6 ee82
00000e0 0300 1500 0000 0000 c204 3714 9009 3bc3
00000f0 e024 2c8c 93d8 a514 5879 5190 ffff ffff
0000100 ffff ffff ffff ffff ffff ffff ffff ffff
0000110 0300 1500 0000 0000 c204 3714 9009 3bc3
0000120 e024 2c8c 93d8 a514 5879 5190 ffff ffff
0000130 ffff ffff ffff ffff ffff ffff ffff ffff
0000140 0100 0000 0000 0000 b233 a494 e16b 7449
0000150 5fcc 48ee ae19 763c d2cd db7d ffff ffff
0000160 ffff ffff ffff ffff ffff ffff ffff ffff
0000170 0100 0000 0000 0000 b233 a494 e16b 7449
0000180 5fcc 48ee ae19 763c d2cd db7d ffff ffff
0000190 ffff ffff ffff ffff ffff ffff ffff ffff
00001a0 adde afbe cefa beba 0000 0000 0000 0000
00001b0 3819 8f98 c393 a92f 51c6 cf23 ca12 3669
00001c0 593e 417e 561f 03d4 c3f4 6bd2 515d f4e4
00001d0 0100 0000 0106 0000 0000 0000 0000 0000
00001e0 0000 0000 0000 0000 0000 0000 0000 0000
*
0000200 0300 1000 0000 0000 0000 0000 0000 0000
0000210 0000 0000 0000 0000 0000 0000 0000 0000
*
0000230 adde afbe cefa beba 0000 0000 0000 0000
0000240 fb5f 0b4e ffa7 f463 0af7 d422 3d1b 7df4
0000250 3224 b171 84f9 cdb0 42d7 ff7e 770c 06c7
0000260 adde afbe cefa beba 0000 0000 0000 0000
0000270 f1b9 9fda a001 a3ba ce3f 46ee f641 f440
0000280 1079 1cf6 3ec8 55f3 2c8d 4dd0 fa7e 8127
0000290 adde afbe cefa beba 0000 0000 0000 0000
00002a0 5aa9 ea92 a664 c564 06a2 3893 39b0 ad45
00002b0 adf3 ff9d 1790 2688 d3b1 d66a a520 2d73
00002c0 adde afbe cefa beba 0000 0000 0000 0000
00002d0 d931 8471 bc3d b044 7a2c f364 c2c6 d18c
00002e0 704d f08e 8f58 2a96 9082 d2ea 1ff4 a9e6
00002f0 adde afbe cefa beba 0000 0000 0000 0000
0000300 0b40 1d6d 4ffb d2ce 8cda e2b2 2127 2796
0000310 5176 c8cf a31e edad 8d7a 9e9e 82a7 b3c1
0000320 adde afbe cefa beba 0000 0000 0000 0000
0000330 9bd1 dadb 3269 5e00 2f09 8ed4 0922 0397
0000340 ab01 d61b 190e 3c41 b600 402c e407 45ff
0000350 adde afbe cefa beba 0000 0000 0000 0000
0000360 7106 1509 7e89 fa7d 38b9 e01a cb99 3302
0000370 9b44 40d6 af90 b901 b489 1dc0 af25 844f
0000380 9181 e21f 59fc fbb4 dd43 0f31 9600 4eb6
0000390 5e41 7891 4fd2 045c 7113 095d 952f af4f
00003a0 fe43 1cb6 6c0b 1c4d 0b13 42a0 47a9 bc2d
00003b0 f454 80f5 57b2 a25b 3e34 0b76 3fa0 41a8
00003c0 9fc9 8f96 b19b bcf8 5d3b a044 006a 2338
00003d0 b8a0 2453 fdf8 5e34 64b9 aff0 286e 234e
00003e0 eb6b db86 72b2 ad80 cdbc d59d 42bc d29d
00003f0 77af ab6c 0806 c9d8 2f91 8df3 fd45 39df

More samples

https://dl.dropboxusercontent.com/u/35197530/bin/eeprom.bin

Tokens

Here we will document the different types off tokens known in the PS3 All tokens are tied? encrypted? using EID0. They enable additional repository nodes.

List

Token	Location	Size	SPU module	Description
qa_token	sc_eeprom - 0x48D3E	0x50	spu_token_processor.self
user_token	?	?	spu_utoken_processor.self	Encrypted/Signed
token_seed	?	?	?	This is used to create the token with EID0

Token Seed

?

Structure

This section has to be corrected, is only based on debug strings, we need to decrypt the tokens

Token Seed

?

QA Token

User Token

Address	Size	Description
?	?	m_magic
?	?	m_format_version
?	?	m_size
?	?	m_capability
?	?	m_expire_date
?	?	m_idps?
?	?	m_attribute
?	?	m_digest

For every atribute in the token

Address	Size	Description
?	?	attr:m_type
?	?	attr:m_size
?	?	attr:m_data

Dumping SC EEPROM - hardware way

Warning
You can use this method at your own risk. Author is not responsible for any hardware damages and failures.

Bus Pirate 3 Solderless method

You need

1) PS3 motherboard with BGA syscon chip (COK001, COK002, SEM001, DIA001, etc)

2) Bus Pirate v3.6 with connectors.

3) Wires (I used AWG32 150mm with tinned ends, see below)

4) PC with OS Windows7 (Should work on other windows systems, but not tested).

5) A sharp pencil.

6) Fingers ;)

Hardware Part

Find the syscon on your PS3 motherboard.

Look at the EEPROM Pins location and Draw serifs on the upper surface of the chip, strictly on these pins using pencil.

Draw the Pinout for convenience.

Connect Bus-Pirate and AWG32 wires using probe Kit

Connect Bus-Pirate to the EEPROM Pins using the folowing table:

Bus Pirate pin	EEPROM pin
CLK	SKB
CS	CSB
MOSI	DI
MISO	DO
3V3	RBB
GND	Any Ground Point

Use 1 finger to hold the wires. The wires should be well connected with the eeprom pins.

Connect Bus-Pirate to you PC with Windows7 by USB.

Software Part

Big thanks to Dasanko for the hard work and for the Syscon Flasher GUI Tool!!!

Download and Install the driver for Bus-Pirate.

Download link: http://www.ftdichip.com/Drivers/CDM/CDM%20v2.12.00%20WHQL%20Certified.exe

Open the Device Manager and find the port number of your USB Serial Port.

Download and Run Syscon Flasher.exe

Download link: https://mega.co.nz/#!clljxQgQ!vE93p35DJ9-FMKuxpev3zZvPBnxP_IQscPSXK9ocmH8

MD5=D59A8AA9E7BB1AEB753D7C6391CE17B1

There are 6 simple steps to obtain the dump.

1) Select the correct USB Serial Port for Bus-Pirate.

2) Press "Send settings to device" button. If done correctly, then "Mode" Led on the Bus Pirate will be Green.

3) Press "Power on" button. If done correctly, then "VREG" Led on the Bus Pirate will be Red.

4) Press "Browse" button and specify location and file name for your syscon eeprom dump.

5) Specify Offset and Length. Offset=0 Length=0x8000 for full dump the eeprom.

6) Press "Fast Read" button and wait about 15sec.

Enjoy:

My dump, for example:

https://mega.co.nz/#!E1kHgSZJ!4e7TdNLdkQQzinwlnRO2KmaBd0GeBliHuHFe2tkmBgQ

Bus Pirate 3 method by: (Zer0Tolerance)

You need

1) PS3 motherboard. I am using DIA-001. may be we can dump it from another boards, but it is unknown yet.

2) Device that can work with SPI interface and send any commands. I am using a Bus Pirate v3.6 with connectors.

3) Soldering station.

4) Wires (see below).

5) Personal conputer with installed HxD, Putty (or other terminal supporting serial port connections, e.g.:Tera Term) , Notepad++

6) /dev/Hands ;)

Preparation

Find the test points on the motherboard using this picture.

All points are covered with varnish. You need to carefully remove the varnish to the copper and solder the wires to it.

Attach a Bus Pirate to the wires using the following table:

Bus Pirate pin	Test Point
CLK	SKB
CS	CSB
MOSI	DI
MISO	DO
3V3	WCB, RBB
GND	Any Ground Point

Make sure that the battery is attached to the motherboard.

Plug your Bus pirate to the USB port on your PC using mini_USB_to_USB cable. (I am using the cable from the ps3 gamepad)

It should be done like this, see the following picture:

Setup software

1) Install the driver for the Bus Pirate and setup your virtual COM port for it using following table:

Parameter	Value
Bits per second	115200
Data bits	8
Parity	None
Stop bits	1
Flow control	None

Open Putty and set it up:

session params:

connection type: Serial

Serial line: COM3 (choose your virtual COM port)

Speed (baud rate): 115200

Logging params:

Session logging: All session output

Log file name: click Browse button and specify your logfile, for example: C:\PS3\Logs\logfile.log

Now click Open button and setup mode for bus pirate using following commands:

Command	Description
m	(mode)
5	(SPI)
4	(Set speed: 1MHz)
2	(Clock polarity: Idle high)
1	(Output clock edge: Idle to active
1	(Input sample phase: Middle *default)
2	(CS: /CS)
2	(Select output type: Normal (H=3.3V, L=GND))

Enable 3.3V: Just type: W (big leter) and press Enter.

Obtain the dump

Type: [0xa8 0x00 0x00 r:32768] and press Enter.

Wait until dumping process will be completed and close Putty.

Thats all. The dump must be into your logfile.log

You can use Notepad++ and Hex Editor like HxD to convert the dump to binary format.

Read Command is 0xA8 0xXX 0xXX, XX XX is a block id to be read, the full EEPROM is 32768 bytes lenght (0x8000), [r:] are syntax command of the Bus Pirate for start, read byte and end

Arduino Mega method by: (Abkarino)

 I had build my own Syscon EEPROM flasher based on open source hardware "Arduino Mega" and some resistors.

This flasher will allow you fully read/write to your Syscon EEPROM (FAT consoles only till now).

You need

1) PS3 motherboard. I had used SEM-0001 board by desoldering Syscon chip form it but you can use, DIA-001 for example without desoldering Syscon chip since all eeprom pins had a test points in the board it self.

2) Arduino Mega or any Arduino board.

3) 6 x 3.6 KOHM resistors + 6 x 1.8 KOHM resistors (work together as a voltage dividers since Arduino IO logic is 5.0v and Syscon EEPROM IO Logic is 3.3v).

4) Soldering station.

5) Wires & Bread board (Optional).

6) Any PC that have terminal software like Putty, RealTerm and so on to access serial port, and any Hex Editor like HxD.

Preparation

Find the test points on the motherboard using this picture.

Or if you have a very good soldering skills and tools to desolder your SysCon then you can desolder your SysCon and solder your wires to it directly.

All points are covered with varnish. You need to carefully remove the varnish to the copper and solder the wires to it.

Attach a Arduino Mega to the wires using the following table:

Arduino Mega pin	Test Point	Syscon Pin
SCL (52)	SKB	E16
SS (53)	CSB	F16
MOSI (51)	DI	G16
MISO (50)	DO	H16
WP (48)	WCB	J15
RB (49)	RBB	J16
VCC (3.3v)	Not needed if you used battery power	G11
GND	Any Ground Point	C15

Make sure that the battery is attached to the motherboard if you will dump/flash SysCon EEPROM in board.

Wiring Diagram & Photos

PS3 SysCon EEPROM Flasher

Fat SysCon Desoldered And Attached To Arduino

SysCon EEPROM Dumping Process

Arduino Sketch Source Code

Here is my Arduino Mega sketch source code to allow you to read/write/erase PS3 Syscon EEPROM. http://pastie.org/10004682#8,19

SC EEPROM

SC EEPROM Info

SC EEPROM Commands

SC EEPROM dumps

Important Offsets

EEPROM Offset Table - Flags and Tokens

Undocumented config

lv0 SC EEPROM usage

System Data From EEPROM

Dumpable EEPROM Offset - Block ID and Block Offset Mapping Table (NVS Service)

Dumpable only with HW flasher EEPROM Offsets - Full Mapping Table (NAND Only)

Authenticated Data Regions Crypto Analysis

Tests

Conclusion

Acknowledgements

Dumping your SC EEPROM

Linux

Hashes

Linux

Installed Package info

Hashes

Dumped data(SLIM)

More samples

Tokens

List

Token Seed

Structure

Token Seed

QA Token

User Token

Dumping SC EEPROM - hardware way

Bus Pirate 3 Solderless method

You need

Hardware Part

Software Part

Bus Pirate 3 method by: (Zer0Tolerance)

You need

Preparation

Setup software

Obtain the dump

Arduino Mega method by: (Abkarino)

You need

Preparation

Wiring Diagram & Photos

Arduino Sketch Source Code

Navigation menu

Search