Switch boards

Description

The Switch board is a daughterboard where are located the input switches, and some leds for outputs and fireworks

• Switch board components
  • Switches: Power and Eject buttons
  • Green and Red leds, all switch board models have them, are needed to show the standby/poweron modes neither the infamous YLOD
  • Eject led, this is the only led not controlled by syscon, the line goes to the bluray drive, so is the bluray drive who decides when is lighted on
  • White backlight leds, this was added for PS3 slim models with the new design of the buttons (not touch sensitive)
  • Unknown subcircuit leds, this seems some kind of experiment that escaped the prototyping table and entered retail production, for some reason exists in some retail PS3 but seems deactivated and partially unpopulated

• Switch board circuit overview (based on how HSW-001 works, this could be different for other switch board models)
  • When Power or Eject switches are pressed the correlating syscon pins are pulled down (grounded)
  • All LED's have its own resistor with a different value to control the current (thus light intensity) and one or more diodes to protect the circuit
  • The LED's on the switch board are turned on either by syscon (all them except one) or by the BD drive controller (only the eject blue led) by using an intermediary transistor
  • That transistors connects the LED ground pin to ground when the signal to turn them on is sent by syscon or by the BD drive controller (the other pin of the LED is connected permanently to the 5 volts standby line)

Comparison of functionality

PS3 retail switch boards

PS3		Switch board			Switches		Leds
PS3 Model	Motherboard	Model	Part number	Connector	Power	Eject	Standby/PowerOn/YLOD	Eject	Switches Backlight	Board Contour Backlight (factory disabled)
CECHAxx CECHBxx	COK-001	CSW-001	1-871-871-21	10 pins	Touch sensitive	Touch sensitive	1x red (2 pins) 1x green (2 pins)	1x blue	No	No
CECHCxx CECHExx	COK-002
CECHGxx	SEM-001	Integrated on motherboard			Touch sensitive	Touch sensitive	1x red (2 pins) ? 1x green (2 pins) ?	1x blue	No	No
CECHHxx	DIA-001
CECHJxx CECHKxx	DIA-002
CECHLxx CECHMxx CECHPxx CECHQxx	VER-001
CECH-20xx	DYN-001	DSW-001	1-880-056-11	10 pins	Pressure	Pressure	1x red/green (dual, 4 pins)	1x blue	2x white (power) 2x white (eject)	1x red (left-top). 1x blue (right-top) 1x blue (left-bottom). 1x unpopulated (right-bottom)
CECH-21xx	SUR-001	HSW-001	1-881-946-11 1-881-946-21	10 pins	Pressure	Pressure	1x red/green (dual, 4 pins)	1x blue	2x white (power) 2x white (eject)	1x red (left-top). 1x unpopulated (right-top) 1x blue (left-bottom). 1x unpopulated (right-bottom)
CECH-25xx	JTP-001 JSD-001
CECH-30xx	KTE-001	KSW-001	1-884-751-31	6 pins	Pressure	Pressure	1x red/green (dual, 4 pins)	No	No	No
SuperSlim	MSX-001 MPX-001 NPX-001 ? PPX-001 ? PQX-001 ? RTX-001 ?	MSW-001	1-886-929-11	6 pins	Pressure	No	1x red/green (dual, 4 pins)	No	No	No

• Notes
  • Boardmodel naming seems thus first letter of SKU motherboard (C=COK, D=DYN, K=KTE, M=MSX/MPX) + "SW-001" (with the exception of HSW-001)

Flex Ribbon cables

• 

  Switch board Flex Ribbon Cable (PS3 1000 series, top view)

• 

  Switch board Flex Ribbon Cable (PS3 1000 series, bottom view)

• 

  Switch board Flex Ribbon Cable (PS3 2000 series, top view)

• 

  Switch board Flex Ribbon Cable (PS3 3000 series, top view)

• 

  Switch board Flex Ribbon Cable (PS3 3000 series, bottom view)

Switch boards Pinout comparison

CSW-001

Switch board CSW-001 (PCB top view)

• Part number: 1-871-871-21
• Compatible with PS3 models:
  • CECHAxx, CECHBxx with motherboard COK-001
  • CECHCxx, CECHExx with motherboard COK-002

CSW-001 Pinout

Pin	Name	Connected to		Description
		On Motherboard	On Switch board
1	GND	GND	GND	Ground
2	SW_PWM	Syscon pad N9	Testpad ?	FREQ. Intended to send a PWM signal to the switch board ?
3	RMC_IN	Syscon pad R10 Service Connector (CN4009) pin 17	Testpad ?. NC	ReMote Control INput The IR receiver component is missing in the Switch board but existed in some PS3 prototypes that was using SIRC protocol and SERV_SIRCS
4	POW_SW	Syscon pad B12	Power Switch
5	EJECT_SW	Syscon pad A12	Eject Switch
6	POW_LED	Syscon pad M7	Green led
7	STBY_LED	Syscon pad N7	Red led
8	BD_LED	BluRay connector (CN3221) pin 50	Blue led
9	GND	GND	GND	Ground
10	+5V_EVER	Power Supply connector (CN6005) pins 4 and 5	VCC	5V Standby

DSW-001

Switch board DSW-001 (PCB top view)

• Part number: 1-880-056-11
• Compatible with PS3 models:
  • CECH-20xx with DYN-001 motherboard

DSW-001 Pinout

Pin	Name	Connected to		Description
		On Motherboard	On Switch board
1	RMC_IN ?	Syscon SW2-30x, pin 13	Testpad	Only This line have a Testpad @ switchboard, seems that it is a service pin. Also connected to a pin of a Service Connectors ?
2	SW_PWM ?	Syscon SW2-30x, pin 12	4x CONTOUR LEDs	Permanently inactive by default. On Switch board is connected to a transistor driving 3 LEDs: TWO BLUE AND ONE RED.
3	?	Syscon SW2-30x, pin 11	2x White leds -	Inner LEDs for EJECT button backlight
			2x White leds -	Inner LEDs for POWER button backlight
4	POW_SW	Syscon SW2-30x, pin 110	Power switch	Sink to ground to activate.
5	EJECT_SW	Syscon SW2-30x, pin 111	Eject switch	Sink to ground to activate.
6	POW_LED	Syscon SW2-30x, pin 5	Green led	Connects to bottom-left corner pin (green gnd) of dual red/green LED over power switch.
7	STBY_LED	Syscon SW2-30x, pin 6	Red led	Connects to top-left corner pin (red gnd) of dual red/green LED over power switch.
8	BD_LED	BluRay Connector, pin 13	Blue led	Connects to blue LED over eject switch.
9	GND	GND	GND	Ground
10	+5V_EVER	Power Supply Connector (CN101), pin 1	VCC	5V Standby

• above top panel view port behind pcb. resistors was not tested.

HSW-001

Switch board HSW-001 (PCB top view)

• Part number: 1-881-946-11, 1-881-946-21
• Compatible with PS3 models:
  • CECH-21xx with SUR-001 motherboard
  • CECH-25xx with JTP-001 or JSD-001 motherboards

HSW-001 Pinout

Pin	Name	Connected to		Description
		On Motherboard	On Switch board
1	SW_PWM ?	Syscon SW2-30x, pin 12	4x CONTOUR LEDs, transistor base pin	The transistor is located in the switch board and drives 2 LEDs with currentlimitor resistors of 3K Ω (red led at left-top) and 820 Ω (blue led at left-bottom) The circuit has unpopulated pads to add another transistor and another 2 LEDs for a total of 4 LEDs driven by a misterious syscon pin
2	+5V_EVER	Power Supply Connector (CN101), pin 1	VCC	5V Standby line from power supply connector CN101, the pin named 5V_EVER on motherboard and 5VSB on power supply
3	?	Syscon SW2-30x, pin 11	2x White leds -	Inner LEDs for EJECT button backlight, with a currentlimitor resistor of 910 Ω
			2x White leds -	Inner LEDs for POWER button backlight, with a currentlimitor resistor of 1K Ω
4	GND	GND	GND	Ground
5	EJECT_SW	Syscon SW2-30x, pin 111	Eject switch	Sink to ground to activate
6	POW_SW	Syscon SW2-30x, pin 110	Power switch	Sink to ground to activate
7	POW_LED	Syscon SW2-30x, pin 5	Green led -	Connects to left-bottom corner pin (green gnd) of dual red/green LED located next to the power switch, with a currentlimitor resistor of 1K Ω
8	STBY_LED	Syscon SW2-30x, pin 6	Red led -	Connects to left-top corner pin (red gnd) of dual red/green LED located next to the power switch, with a currentlimitor resistor of 1K2 Ω
9	BD_LED	BluRay controller CXD5131R-1, pin 36 (on SUR-001/JSD-001) or BluRay controller R8J32830FPV1, pin ?? (on JTP-001)	Blue led -	Connects to blue LED located next to the eject switch, with a currentlimitor resistor of 560 Ω
10	GND	GND	GND	Ground

KSW-001

Switch board KSW-001 (PCB top view)

• Part number: 1-884-751-31
• Compatible with PS3 models:
  • CECH-30xx with KTE-001 motherboard

KSW-001 Pinout

Pin	Name	Connected to		Description
		On Motherboard	On Switch board
1	EJECT_SW	Syscon SW3-30x, pin 83 ?	Eject switch	Sink to ground to activate
2	+5V_EVER	VCC	VCC	5V Standby
3	POW_SW	Syscon SW3-30x, pin 81 ?	Power switch	Sink to ground to activate
4	STBY_LED	Syscon SW3-30x, pin ?	Red led	Connects to right-top corner pin (red gnd) of dual red/green LED over power switch,
5	POW_LED	Syscon SW3-30x, pin ?	Green led	Connects to top right corner pin (green gnd) of dual red/green LED over power switch,
6	GND	GND	GND	Ground

• above top panel view port behind pcb. resistors was not tested.

MSW-001

Switch board MSW-001 (PCB top view)

• Part number: 1-886-929-11
• Compatible with PS3 models:
  • ?

MSW-001 Pinout

Pin	Name	Connected to		Description
		On Motherboard	On Switch board
1	?	?	GND
2	?	?	GND
3	?	?	POW_SW
4	?	?	POW_LED
5	?	?	VCC
6	?	?	STBY_LED

---

Modding

Contour backlight in PS3 2000 Series boards

PS3 2000 series (CECH-20xx, CECH-21xx, and CECH-25xx, with Switch boards DSW-001 and HSW-001) has been designed to have a lighted line all around the top edge of the Switch board

Light rays bouncing surfaces, and light reactive materials

Switch board PS3 2000 series
Light rays schematic in contour leds

The plastic plate uses a "light reactive" material along the edge and in a squared hole in the corner allows the light to "transpass" it

The ligth rays "bounces" inside this material, and the first bouncing surface over the squared hole is a plane at 45 degrees angle. This first bounce aligns the light rays in paralell to the board, the next bounces happens all along the curved surface in horizontal

The reflection of this surfaces can be increased a bit with chrome stickers (or alluminium tape). The case has a plane border of 3,5mm x 17,7cm perfect to stick in it, this way the glue layer of the sticker is at the other side, but the case doesnt have the 45 degrees surface (it has a weird hole instead), you can use other colors for the sticker/s because the color is partially visible from outside (preferably lighter colors or one that matches your led/s color to enhance it)

HSW-001

See HSW-001

DSW-001 Contour backlight

• Enabling contour LEDs in DSW-001 Switch board: | Original thread (french) | Google translated (english)

Other links related

• HSW-001 pinout schematic: http://www.ps3hax.net/showthread.php?p=544479#post544479
• Contour leds tests video: http://www.youtube.com/watch?v=leapBkrm5tk