Switch boards: Difference between revisions

From PS3 Developer wiki
Jump to navigation Jump to search
(→‎Modding: variations of the proposed circuit)
 
(113 intermediate revisions by 7 users not shown)
Line 1: Line 1:
= Description =
The [[Switch boards|Switch board]] is a daughterboard where are located the input switches, and some leds for outputs and fireworks


= Comparison of functionality =
*'''Switch board components'''
**'''Switches''': Power and Eject buttons
**'''Green and Red leds''', all switch board models have them, are needed to show the standby/poweron modes and the infamous YLOD
**'''Eject led''', this is the only led not controlled by syscon, the line goes to the bluray controller, so is the bluray controller who decides when is lighted on
**'''White backlight leds''', this was added for PS3 slim models with the new case design and the new pressure buttons (not touch sensitive)
**'''Unknown subcircuit leds''', this seems some kind of experiment that escaped the prototyping table and entered retail production, for some reason exists in some retail PS3 but seems deactivated and partially unpopulated
**'''IC''', there are a couple of "chips" only in the first model of the switch board, probably related with the touch sensitive feature and maybe others


{| class="wikitable"
|-
! rowspan="2" | PS3 Series !! colspan="2" | Power Eject board !! rowspan="2" | Connector<BR />(number of pins) !! colspan="2" | Buttons || colspan="4" | Leds
|-
! Model !! Part {{numero}} !! Power !! Eject !! Standby/Power On/YLOD !! Eject !! Power Eject buttons backlight !! Board contour backlight
|-
| 1000 Series
| [[CSW-001]] || 1-871-871-21 || 10 || {{yes}} || {{yes}}
| style="background:#55CC55; color:#FFFFFF;" | {{nowrap|1x red}} + {{nowrap|1x green}} || style="background:#55CC55; color:#FFFFFF;" | {{nowrap|1x blue}} || {{no}} || {{no}}
|-
| rowspan="2" | 2000 Series
| [[DSW-001]] || 1-880-056-11 || 10 || {{yes}} || {{yes}}
| style="background:#55CC55; color:#FFFFFF;" | {{nowrap|1x red/green (dual)}} || style="background:#55CC55; color:#FFFFFF;" | 1x blue || style="background:#55CC55; color:#FFFFFF;" | {{nowrap|2x white (power)}} + {{nowrap|2x white (eject)}} || style="background:#55CC55; color:#FFFFFF;" | {{nowrap|1x red (left-top)}} + {{nowrap|1x blue& (left-bottom)}} + {{nowrap|1x green (right-top)}} + {{nowrap|1 unpopulated}}
|-
| [[HSW-001]] || 1-881-946-21 || 10 || {{yes}} || {{yes}}
| style="background:#55CC55; color:#FFFFFF;" | {{nowrap|1x red/green (dual)}} || style="background:#55CC55; color:#FFFFFF;" | {{nowrap|1x blue}} || style="background:#55CC55; color:#FFFFFF;" | {{nowrap|2x white (power)}} + {{nowrap|2x white (eject)}} || style="background:#55CC55; color:#FFFFFF;" | {{nowrap|1x red (left-top)}} + {{nowrap|1x blue (left-bottom)}} + {{nowrap|2 unpopulated}}
|-
| 3000 Series
| [[KSW-001]] || 1-884-751-31 || 6 || {{yes}} || {{yes}}
| style="background:#55CC55; color:#FFFFFF;" | {{nowrap|1x red/green (dual)}} || {{no}} || {{no}} || {{no}}
|-
| 4000 Series
| [[MSW-001]] || 1-886-929-11 || 6 || {{yes}} || {{no}}
| style="background:#55CC55; color:#FFFFFF;" | {{nowrap|1x red/green (dual)}} || {{no}} || {{no}} || {{no}}
|-
|}


*Notes
*'''Switch board circuit overview''' (based on how [[HSW-001]] works, this could be different for other switch board models)
**Boardmodel naming seems thus first letter of SKU motherboard (C=COK / D=DYN / K-KTE / M=MSX/MPX) + "SW-001" (with some exception, like the HSW-001 seen above)
**When Power or Eject switches are pressed the correlating syscon pins are pulled down (grounded)
**All LED's have its own resistor with a different value to control the current (thus light intensity) and one or more diodes to protect the circuit
**The LED's on the switch board are turned on either by syscon (all them except one) or by the BD drive controller (only the eject blue led) by using an intermediary transistor
**That transistors connects the LED ground pin to ground when the signal to turn them on is sent by syscon or by the BD drive controller (the other pin of the LED is connected permanently to the 5 volts standby line)


= Power Eject boards Models =
= Comparison of functionality =
 
== CSW-001 ==
 
<gallery>
File:Power Eject board CSW-001 (PCB top view).jpg|Power Eject board CSW-001 (PCB top view)
File:Power Eject board CSW-001 (PCB bottom view).jpg|Power Eject board CSW-001 (PCB bottom view)
</gallery>
 
== DSW-001 ==
 
<gallery>
File:Power Eject board DSW-001 (top view).jpg|Power Eject board DSW-001 (top view)
File:Power Eject board DSW-001 (bottom view).jpg|Power Eject board DSW-001 (bottom view)
File:Power Eject board DSW-001 (PCB top view).jpg|Power Eject board DSW-001 (PCB top view)
File:Power Eject board DSW-001 (PCB bottom view).jpg|Power Eject board DSW-001 (PCB bottom view)
</gallery>


== HSW-001 ==
{| class="wikitable" style="line-height:120%"
 
|+PS3 retail switch boards
<gallery>
! colspan="2" | PS3 !! colspan="3" | Switch board !! colspan="2" | Switches || colspan="4" | Leds
File:Power Eject board HSW-001 (top view).jpg|Power Eject board HSW-001 (top view)
File:Power Eject board HSW-001 (PCB with ribbon cable, top view).jpg|Power Eject board HSW-001 (PCB with ribbon cable, top view)
File:Power Eject board HSW-001 (PCB top view).jpg|Power Eject board HSW-001 (PCB top view)
File:Power Eject board HSW-001 (PCB bottom view).jpg|Power Eject board HSW-001 (PCB bottom view)
File:Power Eject board HSW-001 (JSD-001) schematic.jpg|Power Eject board HSW-001 (JSD-001) schematic
File:Power Eject board HSW-001 (Contour LEDs subcircuit, unpopulated components).jpg|Power Eject board HSW-001 (Contour LEDs subcircuit, unpopulated components)
</gallery>
 
{| class="wikitable sortable"
|+HSW-001 Pinout
! rowspan="2" | Pin !! colspan="2" | Signal/Connected to !! rowspan="2" | Description
|-
|-
! On Motherboard<!--// <BR />(Syscon [[SW2-30x]] pins)  //--> !! On Power Eject board
! [[SKU_Models|PS3 Model]] !! [[Motherboard_Revisions|Motherboard]] !! Model !! Part number !! Connector !! Power !! Eject !! Standby/PowerOn/<abbr title="Yellow color is made by lighting red + green leds together">YLOD</abbr> !! Eject !! Switches Backlight !! Board Contour Backlight
|-
|-
| 1 || style="color:white; background-color:darkgrey;" | N.C. || 4x CONTOUR LEDs || Not connected on motherboard<br />On Power Eject board is connected to a transistor driving 2 LEDs with currentlimitor resistors of 3K {{ohm}} (red led at left-top) and 820 {{ohm}} (blue led at left-bottom)
| [[CECHAxx]]<BR/>[[CECHBxx]]
| [[COK-001]]
| rowspan="2" | [[CSW-001]] || rowspan="2" | 1-871-871-21 || rowspan="2" | 10 pins || rowspan="2" | Touch sensitive || rowspan="2" | Touch sensitive
| rowspan="2" | 1x <span style="color:#ffffff; background:#ff0000; outline:1px solid #444444;">&nbsp;red&nbsp;</span> (2 pins)<BR/>1x <span style="color:#ffffff; background:#00ff00; outline:1px solid #444444;">&nbsp;green&nbsp;</span> (2 pins) || rowspan="2" | 1x <span style="color:#ffffff; background:#aaaaff; outline:1px solid #444444;">&nbsp;blue&nbsp;</span> || rowspan="2" style="background:lightgrey; text-align:center;" | N/A || rowspan="2" style="background:lightgrey; text-align:center;" | N/A
|-
|-
| 2 || style="color:white; background-color:#CC3333;" | VCC || style="color:white; background-color:#CC3333;" | VCC || style="color:white; background-color:#CC3333;" | +5V DC VCC
| [[CECHCxx]]<BR/>[[CECHExx]]
| [[COK-002]]
|-
|-
| 3 || || 4x WHITE LEDs|| Inner light for power and eject buttons, power LEDs with a currentlimitor resistor of 1K {{ohm}}, and eject LEDs with a currentlimitor resistor of 910 {{ohm}}
| [[CECHGxx]]
| [[SEM-001]]
| colspan="3" rowspan="4" style="background:lightgrey; text-align:center;" | Integrated on motherboard || rowspan="4" | Touch sensitive || rowspan="4" | Touch sensitive
| rowspan="4" | 1x <span style="color:#ffffff; background:#ff0000; outline:1px solid #444444;">&nbsp;red&nbsp;</span> (2 pins) ?<BR/>1x <span style="color:#ffffff; background:#00ff00; outline:1px solid #444444;">&nbsp;green&nbsp;</span> (2 pins) ? || rowspan="4" | 1x <span style="color:#ffffff; background:#aaaaff; outline:1px solid #444444;">&nbsp;blue&nbsp;</span> || rowspan="4" style="background:lightgrey; text-align:center;" | N/A || rowspan="4" style="background:lightgrey; text-align:center;" | N/A
|-
| [[CECHHxx]]
| [[DIA-001]]
|-
| [[CECHJxx]]<BR/>[[CECHKxx]]
| [[DIA-002]]
|-
| [[CECHLxx]]<BR/>[[CECHMxx]]<BR/>[[CECHPxx]]<BR/>[[CECHQxx]]
| [[VER-001]]
|-
| style="padding:0px" colspan="11" |  
|-
|-
| 4 || style="color:white; background-color:#333333;" | GND || style="color:white; background-color:#333333;" | GND || style="color:white; background-color:#333333;" | Ground
| [[CECH-20xx]]
| [[DYN-001]]
| [[DSW-001]] || 1-880-056-11 || 10 pins || Pressure || Pressure
| 1x dual <span style="color:#ffffff; background:#ff0000; outline:1px solid #444444;">&nbsp;red&nbsp;</span> / <span style="color:#ffffff; background:#00ff00; outline:1px solid #444444;">&nbsp;green&nbsp;</span> (4 pins) || 1x <span style="color:#ffffff; background:#aaaaff; outline:1px solid #444444;">&nbsp;blue&nbsp;</span> || 2x <span style="color:#000000; background:#ffffff; outline:1px solid #444444;">&nbsp;white&nbsp;</span> (power)<BR/>2x <span style="color:#000000; background:#ffffff; outline:1px solid #444444;">&nbsp;white&nbsp;</span> (eject) || 1x <span style="color:#ffffff; background:#ff0000; outline:1px solid #444444;">&nbsp;red&nbsp;</span> (left-top).&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;1x <span style="color:#ffffff; background:#aaaaff; outline:1px solid #444444;">&nbsp;blue&nbsp;</span> (right-top)<BR/>1x <span style="color:#ffffff; background:#aaaaff; outline:1px solid #444444;">&nbsp;blue&nbsp;</span> (left-bottom). 1x <span style="color:#000000; background:lightgrey; outline:1px solid #444444;">&nbsp;N/A&nbsp;</span> (right-bottom)
|-
|-
| 5 || || EJECT button || Sink to ground to activate
| [[CECH-21xx]]
| [[SUR-001]]
| rowspan="2" | [[HSW-001]] || rowspan="2" | 1-881-946-11/21 || rowspan="2" | 10 pins || rowspan="2" | Pressure || rowspan="2" | Pressure
| rowspan="2" | 1x dual <span style="color:#ffffff; background:#ff0000; outline:1px solid #444444;">&nbsp;red&nbsp;</span> / <span style="color:#ffffff; background:#00ff00; outline:1px solid #444444;">&nbsp;green&nbsp;</span> (4 pins) || rowspan="2" | 1x <span style="color:#ffffff; background:#aaaaff; outline:1px solid #444444;">&nbsp;blue&nbsp;</span> || rowspan="2" | 2x <span style="color:#000000; background:#ffffff; outline:1px solid #444444;">&nbsp;white&nbsp;</span> (power)<BR/>2x <span style="color:#000000; background:#ffffff; outline:1px solid #444444;">&nbsp;white&nbsp;</span> (eject) || rowspan="2" | 1x <span style="color:#ffffff; background:#ff0000; outline:1px solid #444444;">&nbsp;red&nbsp;</span> (left-top).&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;1x <span style="color:#000000; background:lightgrey; outline:1px solid #444444;">&nbsp;N/A&nbsp;</span> (right-top)<BR/>1x <span style="color:#ffffff; background:#aaaaff; outline:1px solid #444444;">&nbsp;blue&nbsp;</span> (left-bottom). 1x <span style="color:#000000; background:lightgrey; outline:1px solid #444444;">&nbsp;N/A&nbsp;</span> (right-bottom)
|-
|-
| 6 || || POWER button || Sink to ground to activate
| [[CECH-25xx]]
| [[JTP-001]]<BR/>[[JSD-001]]
|-
|-
| 7 || || GREEN led || Connects to left-bottom corner pin (green gnd) of dual red/green LED over power button, with a currentlimitor resistor of 1K {{ohm}}
| [[CECH-30xx]]
| [[KTE-001]]
| [[KSW-001]] || 1-884-751-31 || 6 pins || Pressure || Pressure
| 1x dual <span style="color:#ffffff; background:#ff0000; outline:1px solid #444444;">&nbsp;red&nbsp;</span> / <span style="color:#ffffff; background:#00ff00; outline:1px solid #444444;">&nbsp;green&nbsp;</span> (4 pins) || style="background:lightgrey; text-align:center;" | N/A || style="background:lightgrey; text-align:center;" | N/A || style="background:lightgrey; text-align:center;" | N/A
|-
| style="padding:0px" colspan="11" |
|-
|-
| 8 || || RED led || Connects to left-top corner pin (red gnd) of dual red/green LED over power button, with a currentlimitor resistor of 1K2 {{ohm}}
| rowspan="3" | SuperSlim
| [[MSX-001]]<BR/>[[MPX-001]]<BR/>[[NPX-001]] ?
| [[MSW-001]] || 1-886-929-11/21/31 || 6 pins || Pressure || style="background:lightgrey; text-align:center;" | N/A
| 1x dual <span style="color:#ffffff; background:#ff0000; outline:1px solid #444444;">&nbsp;red&nbsp;</span> / <span style="color:#ffffff; background:#00ff00; outline:1px solid #444444;">&nbsp;green&nbsp;</span> (4 pins) || style="background:lightgrey; text-align:center;" | N/A || style="background:lightgrey; text-align:center;" | N/A || style="background:lightgrey; text-align:center;" | N/A
|-
|-
| 9 || || BLUE led || Connects to blue LED over eject button, with a currentlimitor resistor of 560 {{ohm}}
| [[PPX-001]]<BR/>[[PQX-001]]
|-
| [[PSW-001]] || 1-888-628-21 || 6 pins ? || Pressure || style="background:lightgrey; text-align:center;" | N/A
| 10 || style="color:white; background-color:#333333;" | GND || style="color:white; background-color:#333333;" | GND || style="color:white; background-color:#333333;" | Ground
| 1x dual <span style="color:#ffffff; background:#ff0000; outline:1px solid #444444;">&nbsp;red&nbsp;</span> / <span style="color:#ffffff; background:#00ff00; outline:1px solid #444444;">&nbsp;green&nbsp;</span> (4 pins) || style="background:lightgrey; text-align:center;" | N/A || style="background:lightgrey; text-align:center;" | N/A || style="background:lightgrey; text-align:center;" | N/A
|-
|-
| [[RTX-001]]<BR/>[[REX-001]]
| [[RSW-001]] || 1-893-506-11/31 || 6 pins ? || Pressure || style="background:lightgrey; text-align:center;" | N/A
| 1x dual <span style="color:#ffffff; background:#ff0000; outline:1px solid #444444;">&nbsp;red&nbsp;</span> / <span style="color:#ffffff; background:#00ff00; outline:1px solid #444444;">&nbsp;green&nbsp;</span> (4 pins) || style="background:lightgrey; text-align:center;" | N/A || style="background:lightgrey; text-align:center;" | N/A || style="background:lightgrey; text-align:center;" | N/A
|}
|}


*Notes
*Notes
**All LEDs on the board (except the subcircuit with the contour LEDs) are switched on/of from his GND pin (the other pin of the LED's is connected permanently to a volts line). In other words, when the LED is activated the line along the flex cable is connected to GND
**The names of the first Switch Board models are composed by the first letter of the first PS3 motherboard that used the switch board + the suffix '''SW''' (acronym of '''SW'''itch). E.g: [[COK-001|'''C'''OK-001]]=[[CSW-001|'''C'''SW-001]], [[DYN-001|'''D'''YN-001]]=[[DSW-001|'''D'''SW-001]]
**Contour LED's
**Since [[CECH-21xx]]/[[SUR-001]] the first character of the switch board name indicates the [[Chassis_ID|Chasis Type]], included in the [[Platform ID]]. E.g: [[SUR-001]] = Cok'''H'''11 so his switch board was named [[HSW-001|'''H'''SW-001]]
***Are separated from the rest of the board by a transistor, the transistor is activated by a volts signal from PIN1 of the connector, but the motherboard doesnt send this signal, discuss in [[Talk:Power_Eject_boards|Talk Page]]
***There are several ways to re-enable the contour LED's. And there are solder points without components to duplicate this subcircuit to add another 2 LEDs more for a total of 4. See [[Power_Eject_boards#Modding|Modding section]]


== KSW-001 ==
= Flex Ribbon cables =


<gallery>
<gallery>
File:Power Eject board KSW-001 (top view).jpg|Power Eject board KSW-001 (top view)
File:Power Eject Flex Ribbon Cable (PS3 1000 series, top view).jpg|Switch board Flex Ribbon Cable (PS3 1000 series, top view)
File:Power Eject board KSW-001 (PCB top view).jpg|Power Eject board KSW-001 (PCB top view)
File:Power Eject Flex Ribbon Cable (PS3 1000 series, bottom view).jpg|Switch board Flex Ribbon Cable (PS3 1000 series, bottom view)
File:Power Eject board KSW-001 (PCB with ribbon cable, bottom view).jpg|Power Eject board KSW-001 (PCB with ribbon cable, bottom view)
File:Power Eject Flex Ribbon Cable (PS3 2000 series, top view).jpg|Switch board Flex Ribbon Cable (PS3 2000 series, top view)
File:Power Eject board KSW-001 (PCB bottom view).jpg|Power Eject board KSW-001 (PCB bottom view)
File:Power Eject Flex Ribbon Cable (PS3 3000 series, top view).jpg|Switch board Flex Ribbon Cable (PS3 3000 series, top view)
File:Power Eject Flex Ribbon Cable (PS3 3000 series, bottom view).jpg|Switch board Flex Ribbon Cable (PS3 3000 series, bottom view)
</gallery>
</gallery>


== MSW-001 ==
= Switch boards Pinout =
== CSW-001 ==
<div style="float:right">[[File:Power Eject board CSW-001 (PCB top view).jpg|500px|thumb|left|Switch board CSW-001 (PCB top view)]]</div>
*[[CSW-001]] is a [[Switch boards|switch board]] compatible with PS3 models:
**[[CECHAxx]], [[CECHBxx]] with motherboard [[COK-001]]
**[[CECHCxx]], [[CECHExx]] with motherboard [[COK-002]]
{{CSW-001 pinout}}
== DSW-001 ==
<div style="float:right">[[File:Power Eject board DSW-001 (PCB top view).jpg|500px|thumb|left|Switch board DSW-001 (PCB top view)]]</div>
*[[DSW-001]] is a [[Switch boards|switch board]] compatible with PS3 models:
**[[CECH-20xx]] with [[DYN-001]] motherboard
{{DSW-001 pinout}}
== HSW-001 ==
<div style="float:right">[[File:Power Eject board HSW-001 (PCB top view).jpg|500px|thumb|left|Switch board HSW-001 (PCB top view)]]</div>
*[[HSW-001]] is a [[Switch boards|switch board]] compatible with PS3 models:
**[[CECH-21xx]] with [[SUR-001]] motherboard
**[[CECH-25xx]] with [[JTP-001]] or [[JSD-001]] motherboards
{{clear}}
{{HSW-001 pinout}}


<gallery>
== KSW-001 ==
File:Power Eject board MSW-001 (PCB top view).jpg|Power Eject board MSW-001 (PCB top view)
<div style="float:right">[[File:Power Eject board KSW-001 (PCB top view).jpg|600px|thumb|left|Switch board KSW-001 (PCB top view)]]</div>
File:Power Eject board MSW-001 (PCB bottom view).jpg|Power Eject board MSW-001 (PCB bottom view)
*[[KSW-001]] is a [[Switch boards|switch board]] compatible with PS3 models:
</gallery>
**[[CECH-30xx]] with [[KTE-001]] motherboard
{{KSW-001 pinout}}


= Flex Ribbon cables =
== MSW-001 ==
 
<div style="float:right">[[File:Power Eject board MSW-001 (PCB top view).jpg|700px|thumb|left|Switch board MSW-001 (PCB top view)]]</div>
<gallery>
*[[MSW-001]] is a [[Switch boards|switch board]] compatible with PS3 models:
File:Power Eject Flex Ribbon Cable (PS3 1000 series, top view).jpg|Power Eject Flex Ribbon Cable (PS3 1000 series, top view)
**[[MSX-001]], [[MPX-001]]
File:Power Eject Flex Ribbon Cable (PS3 1000 series, bottom view).jpg|Power Eject Flex Ribbon Cable (PS3 1000 series, bottom view)
{{MSW-001 pinout}}
File:Power Eject Flex Ribbon Cable (PS3 2000 series, top view).jpg|Power Eject Flex Ribbon Cable (PS3 2000 series, top view)
== PSW-001 ==
File:Power Eject Flex Ribbon Cable (PS3 3000 series, top view).jpg|Power Eject Flex Ribbon Cable (PS3 3000 series, top view)
*[[PSW-001]] is a [[Switch boards|switch board]] compatible with PS3 models:
File:Power Eject Flex Ribbon Cable (PS3 3000 series, bottom view).jpg|Power Eject Flex Ribbon Cable (PS3 3000 series, bottom view)
**[[PPX-001]], [[PQX-001]]
</gallery>
PSW-001 pinout... is the same than MSW-001 ?
== RSW-001 ==
*[[RSW-001]] is a [[Switch boards|switch board]] compatible with PS3 models:
**[[RTX-001]], [[REX-001]]
RSW-001 pinout... is the same than MSW-001 ?


= Modding =
= Modding =


== Contour backlight in PS3 2000 Series boards ==
== Contour backlight in PS3 2000 Series boards ==
PS3 2000 series ([[CECH-20xx]], [[CECH-21xx]], and [[CECH-25xx]], with power eject boards DSW-001 and HSW-001) has been designed to have a lighted line all around the top edge of the power eject board
<div style="float:right">[[File:Power Eject board PS3 2000 series (light rays schematic in contour leds).jpg|500px|thumb|left|Switch board PS3 2000 series<BR />Light rays schematic in contour leds]]</div>
 
PS3 2000 series [[CECH-20xx]] (with Switch board [[DSW-001]]), [[CECH-21xx]] and [[CECH-25xx]] (with Switch board [[HSW-001]]) has been designed to have a lighted line all around the top edge of the Switch board
'''Light rays bouncing surfaces, and light reactive materials'''
<div style="float:right">[[File:Power Eject board PS3 2000 series (light rays schematic in contour leds).jpg|500px|thumb|left|Power Eject board PS3 2000 series<BR />Light rays schematic in contour leds]]</div>


The plastic plate uses a "light reactive" material along the edge and in a squared hole in the corner allows the light to "transpass" it
The plastic plate uses a "light reactive" material along the edge and in a squared hole in the corner allows the light to "transpass" it
Line 134: Line 148:


The reflection of this surfaces can be increased a bit with chrome stickers (or alluminium tape). The case has a plane border of 3,5mm x 17,7cm perfect to stick in it, this way the glue layer of the sticker is at the other side, but the case doesnt have the 45 degrees surface (it has a weird hole instead), you can use other colors for the sticker/s because the color is partially visible from outside (preferably lighter colors or one that matches your led/s color to enhance it)
The reflection of this surfaces can be increased a bit with chrome stickers (or alluminium tape). The case has a plane border of 3,5mm x 17,7cm perfect to stick in it, this way the glue layer of the sticker is at the other side, but the case doesnt have the 45 degrees surface (it has a weird hole instead), you can use other colors for the sticker/s because the color is partially visible from outside (preferably lighter colors or one that matches your led/s color to enhance it)
<BR />
<BR />
<BR />
<BR />
<BR />
<BR />
<BR />
<BR />


=== HSW-001 Contour backlight enabled bypassing the transistor ===
For more detailed info about this boards see: [[DSW-001]] and [[HSW-001]] pages
'''Contour LEDs subcircuit'''
<div style="float:right">[[File:Power Eject board HSW-001 (Contour LEDs subcircuit, unpopulated components).jpg|500px|thumb|left|Power Eject board HSW-001<BR />Contour LEDs subcircuit, unpopulated components]]</div>
In HSW-001 board there are 2 leds connected to 2 resistors, 1 zener diode, and 1 transistor (and unpopulated solder points for another similar group of components) all this subcircuit is driven from PIN1 line in the connector


Why is this subcircuit present in this power eject boards is a mystery, obviously it was designed to be lighted but at some point somebody declined the idea (maybe poor lighting, maybe too scandalous for sony taste, who knows)... the point is the the line is cutted in the motherboard, and half of the components are missing so this contour backlight is disabled from factory
{| class="wikitable"
 
|-
The subcircuit is activated by the transistor base pin that goes in-line with the other unpopulated transistor base pin, both does the same function at the same time, each transistor is in chargue of 2 leds with a common zenner diode (the transistor opens/closes the leds ground lines, and when the line is opened the zener diode works as an "voltage regulator" for the subcircuit avoiding "voltage peaks"). These transistors are "isolating" the subcircuit at his left
| {{#ev:youtube|leapBkrm5tk}} || {{#ev:youtube|FUk1q4af7TE}}
 
|-
The unpopulated resistors values are dependant of the leds added
| PS3 [[CECH-20xx]] Switch board [[DSW-001]]. Tests || PS3 [[CECH-25xx]] Switch board [[HSW-001]]. Enabled subcircuit with 2 leds (blue + red)
 
|}
'''Minimal parts version'''
<div style="float:right">[[File:Power Eject board HSW-001 (Enabling contour LEDs, minimal parts version).jpg|500px|thumb|left|Power Eject board HSW-001<BR />(Enabling contour LEDs, minimal parts version)]]</div>
With this method, all the ground pins of the background light LED's are joined together and switched at the same time (4 white LED's from power/eject buttons + the LEDs present in the "contour backlight" subcircuit)
 
The wire is bridging the connector PIN3 (that switches on/of the backlight for power eject buttons) to the collector pin of the transistor, but also is connected to the collector pin of the other unpopulated transistor, this means all the 4 LEDs of the subcircuit (in the case of adding the 2 missing LEDs with his 2 resistors) will be activated at the same time by the wire, and has a common zenner diode to protect the 4 LEDs lines from voltage peaks
 
The transistor function is bypassed by this wire so the area at the left of the transistor/s is not an isolated subcircuit anymore, this can be a problem for the total current of the board and for this reason in the photo there is an "optional" cutted line to disable the white leds for power eject buttons (you are adding 4 leds, so other 4 "needs" to be disabled to ballance the karma)
 
In the case the transistor is activated (seems not posible because the trace is cutted in motherboard) the collector pin (ground for leds) is connected to the the emitter pin (common ground of the Power Eject board), this doesnt interferes with the added wire because the PIN3 line is doing the same function (with another transistor in the motherboard)
 
The top-left LED (red) ground is connected to this tiny black component in verticall that is a '''HUGE 3K {{ohm}}''' resistor, the value of the resistor makes the red light almost not visible, so is a good idea to remove/replace the resistor or to remove the red LED, removing LEDs can be convenient because are different colors (better use one colored LED + 3 whites... or 4 of the same color)
 
To remove a resistor so tiny with a solder iron there is a trick using a melted drop that connects both pins of the component and when all is melted you move the component laterally. If you try to remove a LED of this size with a solder iron his plastic cover will "pop up" in 100% of the cases, if you dont plan to recycle the LED this is not a problem, first you destroy/popup the plastic cover of the LED with the solder tip and then you can use the trick of the melted solder drop, the only caution needed is to dont damage other nearly components and use a good solder iron with a 0,5mm tip or so
 
*Variations (Contour LEDs are separated in 2 groups, turned on/of by 2 separated ground lines... in this list are defined as "group1" and "group2")
**1 wire (both groups grounds driven by 1 wire)
***Wire connected to PIN3 (power/eject buttons white backlight)... 4x contour LEDs are ON when/while PS3 is turned on (is the circuit proposed here as "minimal parts version")
***Wire connected to PIN7 (Power ON dual LED, green color)... 4x contour LEDs are ON when/while PS3 is turned on (with a "triple blink" when turned ON/OFF)
***Wire connected to PIN8 (Standby dual LED, red color)... pointless and annoying, contour LEDs will be permanently ON and there is a better way to achieve this
***Wire connected to PIN9 (Eject LED, blue color)... 4x contour LEDs are ON while there is a disc in the drive, and does a "triple blink" when loading/ejecting a disc
**2 wires (this implyes adding the unpopulated resistors and LEDs, and using 2 wires to separate the LEDs in 2 groups)
***Wire 1 connected to PIN3 (power/eject buttons white backlight), and wire 2 connected to PIN7 (Power ON dual LED, green color)... group1 is ON when/while PS3 is ON (for a total of 50% light intensity), and group2 does a "triple blink" and stays ON (for a total of 100% intensity)
***Wire 1 connected to PIN3 (power/eject buttons white backlight), and wire 2 connected to PIN9 (Eject LED, blue color)... group1 is ON when/while PS3 is ON (for a total of 50% light intensity), and group2 does a "triple blink" when loading/eject a disc or stays ON while a disc is inserted (for a total of 100% intensity)
***Wire 1 connected to PIN7 (Power ON dual LED, green color), and wire 2 connected to PIN8 (Standby dual LED, red color)... there is a better way to activate a group for standby, and group2 does a "triple blink" when loading/eject a disc or stays ON while a disc is inserted (for a total of 100% intensity)... but you have replicate the dual function of the Standby/Power ON dual LED, this means you have all the output for homebrew apps thas uses these LEDS like "fan controll utility" and even error codes like the YLOD
***Wire 1 connected to PIN7 (Power ON dual LED, green color), and wire 2 connected to PIN9 (Eject LED, blue color)... group1 is ON when/while PS3 is turned on with a "triple blink" when turned ON/OFF (for a total of 50% light intensity), and group2 does a "triple blink" when loading/eject a disc or stays ON while a disc is inserted (for a total of 100% intensity)
 
=== DSW-001 Contour backlight ===
*Enabling contour LEDs in DSW-001 Power Eject board: [http://ps3gunz.org/forum/viewtopic.php?pid=590435 | Original thread (french)] [http://translate.google.com/translate?sl=fr&tl=en&js=n&prev=_t&hl=es&ie=UTF-8&u=http%3A%2F%2Fps3gunz.org%2Fforum%2Fviewtopic.php%3Fpid%3D590435&act=url | Google translated (english)]
 
== Other links related ==
*HSW-001 pinout schematic: http://www.ps3hax.net/showthread.php?p=544479#post544479
*Contour leds tests video: http://www.youtube.com/watch?v=leapBkrm5tk
 
{{Console}}


[[Category:Power Eject boards]]
{{Components}}<noinclude>[[Category:Main]]</noinclude>

Latest revision as of 18:27, 5 December 2021

Description[edit | edit source]

The Switch board is a daughterboard where are located the input switches, and some leds for outputs and fireworks

  • Switch board components
    • Switches: Power and Eject buttons
    • Green and Red leds, all switch board models have them, are needed to show the standby/poweron modes and the infamous YLOD
    • Eject led, this is the only led not controlled by syscon, the line goes to the bluray controller, so is the bluray controller who decides when is lighted on
    • White backlight leds, this was added for PS3 slim models with the new case design and the new pressure buttons (not touch sensitive)
    • Unknown subcircuit leds, this seems some kind of experiment that escaped the prototyping table and entered retail production, for some reason exists in some retail PS3 but seems deactivated and partially unpopulated
    • IC, there are a couple of "chips" only in the first model of the switch board, probably related with the touch sensitive feature and maybe others


  • Switch board circuit overview (based on how HSW-001 works, this could be different for other switch board models)
    • When Power or Eject switches are pressed the correlating syscon pins are pulled down (grounded)
    • All LED's have its own resistor with a different value to control the current (thus light intensity) and one or more diodes to protect the circuit
    • The LED's on the switch board are turned on either by syscon (all them except one) or by the BD drive controller (only the eject blue led) by using an intermediary transistor
    • That transistors connects the LED ground pin to ground when the signal to turn them on is sent by syscon or by the BD drive controller (the other pin of the LED is connected permanently to the 5 volts standby line)

Comparison of functionality[edit | edit source]

PS3 retail switch boards
PS3 Switch board Switches Leds
PS3 Model Motherboard Model Part number Connector Power Eject Standby/PowerOn/YLOD Eject Switches Backlight Board Contour Backlight
CECHAxx
CECHBxx 		COK-001 CSW-001 1-871-871-21 10 pins Touch sensitive Touch sensitive 1x  red  (2 pins)
1x  green  (2 pins)		 1x  blue  N/A N/A
CECHCxx
CECHExx 		COK-002
CECHGxx SEM-001 Integrated on motherboard Touch sensitive Touch sensitive 1x  red  (2 pins) ?
1x  green  (2 pins) ?		 1x  blue  N/A N/A
CECHHxx DIA-001
CECHJxx
CECHKxx 		DIA-002
CECHLxx
CECHMxx
CECHPxx
CECHQxx 		VER-001
CECH-20xx DYN-001 DSW-001 1-880-056-11 10 pins Pressure Pressure 1x dual  red  /  green  (4 pins) 1x  blue  2x  white  (power)
2x  white  (eject)		 1x  red  (left-top).        1x  blue  (right-top)
1x  blue  (left-bottom). 1x  N/A  (right-bottom)
CECH-21xx SUR-001 HSW-001 1-881-946-11/21 10 pins Pressure Pressure 1x dual  red  /  green  (4 pins) 1x  blue  2x  white  (power)
2x  white  (eject)		 1x  red  (left-top).        1x  N/A  (right-top)
1x  blue  (left-bottom). 1x  N/A  (right-bottom)
CECH-25xx JTP-001
JSD-001
CECH-30xx KTE-001 KSW-001 1-884-751-31 6 pins Pressure Pressure 1x dual  red  /  green  (4 pins) N/A N/A N/A
SuperSlim MSX-001
MPX-001
NPX-001 ? 		MSW-001 1-886-929-11/21/31 6 pins Pressure N/A 1x dual  red  /  green  (4 pins) N/A N/A N/A
PPX-001
PQX-001 		PSW-001 1-888-628-21 6 pins ? Pressure N/A 1x dual  red  /  green  (4 pins) N/A N/A N/A
RTX-001
REX-001 		RSW-001 1-893-506-11/31 6 pins ? Pressure N/A 1x dual  red  /  green  (4 pins) N/A N/A N/A

Flex Ribbon cables[edit | edit source]

  • Switch board Flex Ribbon Cable (PS3 1000 series, top view)

    Switch board Flex Ribbon Cable (PS3 1000 series, top view)

  • Switch board Flex Ribbon Cable (PS3 1000 series, bottom view)

    Switch board Flex Ribbon Cable (PS3 1000 series, bottom view)

  • Switch board Flex Ribbon Cable (PS3 2000 series, top view)

    Switch board Flex Ribbon Cable (PS3 2000 series, top view)

  • Switch board Flex Ribbon Cable (PS3 3000 series, top view)

    Switch board Flex Ribbon Cable (PS3 3000 series, top view)

  • Switch board Flex Ribbon Cable (PS3 3000 series, bottom view)

    Switch board Flex Ribbon Cable (PS3 3000 series, bottom view)

Switch boards Pinout[edit | edit source]

CSW-001[edit | edit source]

Switch board CSW-001 (PCB top view)
CSW-001 Pinout
[edit]
Pin Name Connected to Description
On Motherboard On Switch board
1 GND GND GND Ground
2 SW_PWM Syscon pad N9 Testpad ? FREQ. Intended to send a PWM signal to the switch board ?
3 RMC_IN Syscon pad R10
Service Connector (CN4009) pin 17		 Testpad ?. NC ReMote Control INput
The IR receiver component is missing in the Switch board but existed in some PS3 prototypes that was using SIRC protocol and SERV_SIRCS
4 POW_SW Syscon pad B12 Power Switch PS3 power button
5 EJECT_SW Syscon pad A12 Eject Switch PS3 eject button
6 POW_LED Syscon pad M7 Green led
7 STBY_LED Syscon pad N7 Red led
8 BD_LED BluRay connector (CN3221) pin 50 Blue led
9 GND GND GND Ground
10 +5V_EVER Power Supply connector (CN6005) pins 4 and 5 VCC 5V Standby

DSW-001[edit | edit source]

Switch board DSW-001 (PCB top view)
DSW-001 Pinout
[edit]
Pin Name Connected to Description
On Motherboard On Switch board
1 RMC_IN ? Syscon SW2-30x, pin 13 Testpad Only This line have a Testpad @ switchboard, seems that it is a service pin.
Also connected to a pin of a Service Connectors ?
2 SW_PWM ? Syscon SW2-30x, pin 12 4x CONTOUR LEDs Permanently inactive by default.
On Switch board is connected to a transistor driving 3 LEDs: TWO BLUE AND ONE RED.
3 ? Syscon SW2-30x, pin 11 2x White leds - Inner LEDs for EJECT button backlight
2x White leds - Inner LEDs for POWER button backlight
4 POW_SW Syscon SW2-30x, pin 110 Power switch PS3 power button Sink to ground to activate.
5 EJECT_SW Syscon SW2-30x, pin 111 Eject switch PS3 eject button Sink to ground to activate.
6 POW_LED Syscon SW2-30x, pin 5 Green led Connects to bottom-left corner pin (green gnd) of dual red/green LED over power switch.
7 STBY_LED Syscon SW2-30x, pin 6 Red led Connects to top-left corner pin (red gnd) of dual red/green LED over power switch.
8 BD_LED BluRay Connector, pin 13 Blue led Connects to blue LED over eject switch.
9 GND GND GND Ground
10 +5V_EVER Power Supply Connector (CN101), pin 1 VCC 5V Standby
  • above top panel view port behind pcb. resistors was not tested.

HSW-001[edit | edit source]

Switch board HSW-001 (PCB top view)
HSW-001 Pinout
[edit]
Pin Name Connected to Description
On Motherboard On Switch board
1 SW_PWM ? Syscon SW2-30x, pin 12 4x CONTOUR LEDs, transistor base pin The transistor is located in the switch board and drives 2 LEDs with currentlimitor resistors of 3K Ω (red led at left-top) and 820 Ω (blue led at left-bottom)
The circuit has unpopulated pads to add another transistor and another 2 LEDs for a total of 4 LEDs driven by a misterious syscon pin
2 +5V_EVER Power Supply Connector (CN101), pin 1 VCC 5V Standby line from power supply connector CN101, the pin named 5V_EVER on motherboard and 5VSB on power supply
3 ? Syscon SW2-30x, pin 11 2x White leds - Inner LEDs for EJECT button backlight, with a currentlimitor resistor of 910 Ω
2x White leds - Inner LEDs for POWER button backlight, with a currentlimitor resistor of 1K Ω
4 GND GND GND Ground
5 EJECT_SW Syscon SW2-30x, pin 111 Eject switch PS3 eject button Sink to ground to activate
6 POW_SW Syscon SW2-30x, pin 110 Power switch PS3 power button Sink to ground to activate
7 POW_LED Syscon SW2-30x, pin 5 Green led - Connects to left-bottom corner pin (green gnd) of dual red/green LED located next to the power switch, with a currentlimitor resistor of 1K Ω
8 STBY_LED Syscon SW2-30x, pin 6 Red led - Connects to left-top corner pin (red gnd) of dual red/green LED located next to the power switch, with a currentlimitor resistor of 1K2 Ω
9 BD_LED BluRay controller CXD5131R-1, pin 36 (on SUR-001/JSD-001)
or
BluRay controller R8J32830FPV1, pin ?? (on JTP-001)		 Blue led - Connects to blue LED located next to the eject switch, with a currentlimitor resistor of 560 Ω
10 GND GND GND Ground


KSW-001[edit | edit source]

Switch board KSW-001 (PCB top view)
KSW-001 Pinout
[edit]
Pin Name Connected to Description
On Motherboard On Switch board
1 EJECT_SW Syscon SW3-30x, pin 83 ? Eject switch PS3 eject button Sink to ground to activate
2 +5V_EVER VCC VCC 5V Standby
3 POW_SW Syscon SW3-30x, pin 81 ? Power switch PS3 power button Sink to ground to activate
4 STBY_LED Syscon SW3-30x, pin ? Red led Connects to right-top corner pin (red gnd) of dual red/green LED over power switch,
5 POW_LED Syscon SW3-30x, pin ? Green led Connects to top right corner pin (green gnd) of dual red/green LED over power switch,
6 GND GND GND Ground
  • above top panel view port behind pcb. resistors was not tested.


MSW-001[edit | edit source]

Switch board MSW-001 (PCB top view)
MSW-001 Pinout
[edit]
Pin Name Connected to Description
On Motherboard On Switch board
1 ? ? GND
2 ? ? GND
3 ? ? POW_SW
4 ? ? POW_LED
5 ? ? VCC
6 ? ? STBY_LED

PSW-001[edit | edit source]

PSW-001 pinout... is the same than MSW-001 ?

RSW-001[edit | edit source]

RSW-001 pinout... is the same than MSW-001 ?

Modding[edit | edit source]

Contour backlight in PS3 2000 Series boards[edit | edit source]

Switch board PS3 2000 series
Light rays schematic in contour leds

PS3 2000 series CECH-20xx (with Switch board DSW-001), CECH-21xx and CECH-25xx (with Switch board HSW-001) has been designed to have a lighted line all around the top edge of the Switch board

The plastic plate uses a "light reactive" material along the edge and in a squared hole in the corner allows the light to "transpass" it

The ligth rays "bounces" inside this material, and the first bouncing surface over the squared hole is a plane at 45 degrees angle. This first bounce aligns the light rays in paralell to the board, the next bounces happens all along the curved surface in horizontal

The reflection of this surfaces can be increased a bit with chrome stickers (or alluminium tape). The case has a plane border of 3,5mm x 17,7cm perfect to stick in it, this way the glue layer of the sticker is at the other side, but the case doesnt have the 45 degrees surface (it has a weird hole instead), you can use other colors for the sticker/s because the color is partially visible from outside (preferably lighter colors or one that matches your led/s color to enhance it)

For more detailed info about this boards see: DSW-001 and HSW-001 pages

Load video
YouTube
Load video
YouTube
PS3 CECH-20xx Switch board DSW-001. Tests PS3 CECH-25xx Switch board HSW-001. Enabled subcircuit with 2 leds (blue + red)
Motherboards
Fat (nand)
Fat (nor)
Slim (nor)
Super Slim (nor/eMMC)
Harddrives
Fujitsu
Hitachi
Seagate
Toshiba
Bluray Drive
Drive
BD-400 · BD-410 · BD-450 · BD-460 · BD-470
Laser
Slide
BD Daughterboards
Motorsensorboards
Sensorboards
Lidsensorboards
Power Supply
Sony
Delta
Panasonic
Nichicon
Chicony
Cooling
Fans
14 cm (fat)
10 cm (slim 2XXX)
8 cm (slim 3XXX)
7.35 cm (super slim 4XXX)
Heatsinks
type 1 · type 2 · type 3 · type 4 · type 5 · type 6 · type 7
Other Boards
Wifi/BT (WI/WB)
Boards
Components
Boards
Components
Boards
Components
Retrieved from "http://www.psdevwiki.com/ps3/index.php?title=Switch_boards&oldid=63703"