USB
USB 2.0
Depending on the SKU Models the PS3 is equiped with 6x (Tool/DECR), 4 or 2 USB (Universal Serial Bus) 2.0 ports with maximum bandwidth of 480 Mbit/s (~57 MB/s), connected internally to a USB-Hub chip.
Note: On PS3 Slim CECH-20xx/DYN-001 and later, the USB port datalines are directly connected to South Bridge without a USB-Hub chip (port is initialised via DC switch IC connected to South Bridge and TH3301 thermistor protect 5V input).
USB lines top view (common traces for all slim models)
USB lines bottom view (common traces for all slim models)
JSD-001/JTP-001 USB connector TH3301 thermistor and DC switch IC to South Bridge
.jpg)
.jpg)
Generic USB Pinout
| Pin | Signal | Description |
|---|---|---|
| 1 | VCC | +5 volt DC (max.500mA) |
| 2 | D- | Data- |
| 3 | D+ | Data+ |
| 4 | GND | Ground |
Internal USB-Hub IC's
GL852-MSG02-MT (USB-Hub 64pin)
Datasheet: http://www.ps3devwiki.com/files/documents/-Datasheets/USB/Genesys_Logic_GL852.pdf
6-806-862-01 / IC3305
Used in PS3 FAT CECHA/COK-001 and CECHB/COK-001
| Pin Name | 64 Pin# | 48Pin# | I/O Type | Description |
|---|---|---|---|---|
| DM0,DP0 | 3,4 | 3,4 | B | USB signals for USPORT |
| DM1,DP1 | 8,9 | 5,6 | B | USB signals for DSPORT1 |
| DM2,DP2 | 14,15 | 9,10 | B | USB signals for DSPORT2 |
| DM3,DP3 | 25,26 | 17,18 | B | USB signals for DSPORT3 |
| DM4,DP4 | 31,32 | 21,22 | B | USB signals for DSPORT4 |
| RREF | 17 | 11 | B | A 680Ω resister must be connected between RREF and analog ground (AGND). |
| OVCUR1#~4 | 56,54,42,40 | 42,40,30,28 | I (pu) |
Active low. Over current indicator for DSPORT1~4 OVCUR1# is the only over current flag for GANG mode. |
| PWREN1#~4 | 57,55,43,41 | 43,41,31,29 | O | Active low. Power enable output for DSPORT1~4 PWREN1# is the only power-enable output for GANG mode. |
| GREEN1~4 | 60,48,44,34 | 45,35,32,23 | 1,3,4: O 2: B (pd) |
Green LED indicator for DSPORT1~4 *GREEN[1~2] are also used to access the external EEPROM. For detailed information, please refer to Chapter 5. |
| AMBER1~4 | 61,49,45,35 | 46,36,33,24 | O (pd) |
Amber LED indicator for DSPORT1~4 *Amber [1~2] are also used to access the external EEPROM |
| PSELF | 50 | 37 | I | 0: GL852 is bus-powered. 1: GL852 is self-powered. |
| PGANG/ SUSPND |
53 | 39 | B | This pin is default put in input mode after power-on reset. Individual/gang mode is strapped during this period. After the strapping period, this pin will be set to output mode, and then output high for normal mode. When GL852 is suspended, this pin will output low. *For detailed explanation, please see Chapter 5 Gang input:1, output: 0@normal, 1@suspend |
| X1 | 20 | 14 | I | 12MHz crystal clock input. |
| X2 | 21 | 15 | O | 12MHz crystal clock output. |
| RESET# | 38 | 26 | I | Active low. External reset input, default pull high 10KΩ. When RESET# = low, whole chip is reset to the initial state. |
| TEST | 39 | 27 | I (pd) |
0: Normal operation. 1: Chip will be put in test mode. |
| AVDD | 11,18,22,28,64 | 1,7,12,16,19 | P | 3.3V analog power input for analog circuits. |
| AGND | 1,12,19,23,29 | 2,8,13,20 | P | Analog ground input for analog circuits. |
| DVDD | 37,47,52,59 | 25,34,38,44,48 | P | 3.3V digital power input for digital circuits |
| DGND | 36,46,51,58,62 | 47 | P | Digital ground input for digital circuits. |
| NC | 2,5~7,10,13,16,24,27,30,33 | - | - | No connection |
Type O Output I Input B Bi-directional B/I Bi-directional, default input B/O Bi-directional, default output P Power / Ground A Analog SO Automatic output low when suspend pu Internal pull up pd Internal pull down odpu Open drain with internal pull up
GL852 (USB-Hub 64pin)
Datasheet: http://www.ps3devwiki.com/files/documents/-Datasheets/USB/Genesys_Logic_GL852.pdf
Used in PS3 FAT CECHC/COK-002
GL852 (USB-Hub 48pin)
Datasheet: http://www.ps3devwiki.com/files/documents/-Datasheets/USB/Genesys_Logic_GL852.pdf
Used in PS3 FAT CECHG/SEM-001
GL852 (USB-Hub 48pin)
Datasheet: http://www.ps3devwiki.com/files/documents/-Datasheets/USB/Genesys_Logic_GL852.pdf
Wifi#UWB-001
Used in PS3 FAT CECHH/DIA-001
GL852 (USB-Hub 48pin)
Datasheet: http://www.ps3devwiki.com/files/documents/-Datasheets/USB/Genesys_Logic_GL852.pdf
Wifi#UWB-001
Used in PS3 FAT CECHJ/DIA-002 and CECHK/DIA-002
GL852 (USB-Hub 48pin)
Datasheet: http://www.ps3devwiki.com/files/documents/-Datasheets/USB/Genesys_Logic_GL852.pdf
Used in PS3 FAT CECHL/VER-001 up and including CECHQ/VER-001
| |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
