88SA8040-TBC1: Difference between revisions
Jump to navigation
Jump to search
mNo edit summary |
(little html errors) |
||
| (2 intermediate revisions by 2 users not shown) | |||
| Line 4: | Line 4: | ||
[[File:Marvell 88SA8040-TBC1.jpg|thumb|left|Marvell 88SA8040-TBC1]]<br />[[File:88SA8040C0-TBC1 Top.jpg|thumb|left|Marvell 88SA8040C0-TBC1 - Top]]<br />[[File:88SA8040C0-TBC1 Bottom.jpg|thumb|left|Marvell 88SA8040C0-TBC1 - Bottom]]<br />[[File:Marvell 88SA8052-pinout.png|thumb|left|Marvell 88SA8040/88SA8052 -TBC1 - pinout]]<br />[[File:Marvell 88SA8040-TBC1-pinout.jpg|thumb|left|Marvell 88SA8040/88SA8052 -TBC1 - application schematic]]</div> | [[File:Marvell 88SA8040-TBC1.jpg|thumb|left|Marvell 88SA8040-TBC1]]<br />[[File:88SA8040C0-TBC1 Top.jpg|thumb|left|Marvell 88SA8040C0-TBC1 - Top]]<br />[[File:88SA8040C0-TBC1 Bottom.jpg|thumb|left|Marvell 88SA8040C0-TBC1 - Bottom]]<br />[[File:Marvell 88SA8052-pinout.png|thumb|left|Marvell 88SA8040/88SA8052 -TBC1 - pinout]]<br />[[File:Marvell 88SA8040-TBC1-pinout.jpg|thumb|left|Marvell 88SA8040/88SA8052 -TBC1 - application schematic]]</div> | ||
alt. part no: [[88SA8040C0-TBC1C000-P107]] (SATA 1.5 Gb/s to PATA 133) <br /> | alt. part no: [[88SA8040C0-TBC1C000-P107]] (SATA 1.5 Gb/s to PATA 133) <br/> | ||
6-710-129-01 / IC3401 <br /> | 6-710-129-01 / IC3401 <br/> | ||
SATA to PATA IDE bridge chip. This is used on motherboards with a PATA blu-ray drive: early PS3 (up to including [[CECHKxx]]/[[DIA-00x#DIA-002|DIA-002]]). <br /> | SATA to PATA IDE bridge chip. This is used on motherboards with a PATA blu-ray drive: early PS3 (up to including [[CECHKxx]]/[[DIA-00x#DIA-002|DIA-002]]). <br/> | ||
<pre> The 88SA8040 is an IC which consists of 9 bus transceivers (three state output) in | <pre> The 88SA8040 is an IC which consists of 9 bus transceivers (three state output) in | ||
| Line 21: | Line 21: | ||
2.5V, dropout voltage is the input-to-output voltage differential with the minimum | 2.5V, dropout voltage is the input-to-output voltage differential with the minimum | ||
input voltage 2.5V. Minimum input operating voltage is 2.5V.</pre> | input voltage 2.5V. Minimum input operating voltage is 2.5V.</pre> | ||
No datasheet found/available : http://www.marvell.com/storage/system-solutions/sata-to-pata-bridge.jsp <br /> | No datasheet found/available : | ||
http://www.marvell.com/storage/system-solutions/sata-to-pata-bridge.jsp <br /> | |||
== Marvell 88SA8040C0-TBC1C000-P107 (SATA to PATA bridge) == | |||
No padouts have been listed (yet), please help to fill this in :) | |||
{{ | {{Wikify}} | ||
[[Category: | |||
{{Motherboard Components}}<noinclude>[[Category:Main]]</noinclude> | |||
Latest revision as of 15:57, 21 February 2018
Marvell 88SA8040-TBC1[edit | edit source]
alt. part no: 88SA8040C0-TBC1C000-P107 (SATA 1.5 Gb/s to PATA 133)
6-710-129-01 / IC3401
SATA to PATA IDE bridge chip. This is used on motherboards with a PATA blu-ray drive: early PS3 (up to including CECHKxx/DIA-002).
The 88SA8040 is an IC which consists of 9 bus transceivers (three state output) in a 24 pin package. Signals are transmitter from A to B when the direction control input (DiR) is at a high level, and from B to A when DiR is at a low level. When the enable input (G) is high, A and B are isolated. And this product has two terminals (V CCA, VCCB), VCCA is connected with control input and A bus side, VCCB is connected with B bus side. VCCA and V CCB are isolated. Consequently, it is best to change the level in case of two supply voltage coexist on one board and application of power management. Dropout Voltage is defined as the input to output differential at which the output voltage drops 2% below its nominal value measured at 1V differential. For outputs below 2.5V, dropout voltage is the input-to-output voltage differential with the minimum input voltage 2.5V. Minimum input operating voltage is 2.5V.
No datasheet found/available :
http://www.marvell.com/storage/system-solutions/sata-to-pata-bridge.jsp
Marvell 88SA8040C0-TBC1C000-P107 (SATA to PATA bridge)[edit | edit source]
No padouts have been listed (yet), please help to fill this in :)
| This article is marked for rewrite/restructuring in proper wiki format. You can help PS3 Developer wiki by editing it. |
| |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
