Revision as of 07:44, 11 October 2024

HV Syscalls

NOTE: Update with graf's work. It'll probably fill in some of the undocumented functions.

lv1_allocate_memory

Create a memory region in the Hypervisor Virtual Address Space (vas)

Kernel Call

result = lv1_allocate_memory( /*IN*/ size, page_size_exp, 0, flags, /*OUT*/ &addr, &muid );

Parameters

Inputs
Register	Description
R3	size - of the region to allocate, must be a multiple of page_size
R4	page_size_exp - where required page_size = 2 ^ page_size_exp
R5	0 - Unknown, see notes
R6	flags - (from linux/include/asm-powerpc/lv1call.h) bit 63: transferability: TF_NO = 0×00, TF_YES = 0×01 bit 62: destruction_scheme: DS_NO_CONNECTIONS = 0×00, DS_ANYTIME = 0×02 bit 61: fail or alternative: FA_FAIL = 0×00, FA_ALTERNATIVE = 0×04 bit 60: need LPAR address 0: ADDR_ANY = 0×00, ADDR_0 = 0×08 function unknown.
Outputs
Register	Description
R3	Status - 0 = OK, LV1_RESOURCE_SHORTAGE (-2), LV1_NO_ENTRY (-6), LV1_DUPLICATE_ENTRY (-7)
R4	addr - LPAR Address of region
R5	muid - Unknown, unused by Kernel

Notes:

page_size_exp takes values of 12 (page_size = 4K) to 21 (page_size = 2M) before LV1_RESOURCE_SHORTAGE (-2) is returned under a fully booted Linux OS. Higher values (24, page_size = 16M) can be found in the actual kernel source and can presumably be made before the OS has fully booted. page_size_exp values below 12 cause a return status of LV1_ILLEGAL_PARAMETER_VALUE (-17).

Input R5 was speculated to be the initialization value for the allocated region, but appears not to be the case. Values other than 0 or 1 appear to return a status of LV1_NO_ENTRY (-6), though a valid value of page_size_exp appears to be checked first (-17 is returned for invalid values of page_size_exp, regardless of the value of R5).

Allocations with flags = 0×00, 0×01, 0×02, 0×03 and 0×04 were successful though the effects of the flags could not be tested at this point. Allocations with flags >= 0×400 return LV1_ILLEGAL_PARAMETER_VALUE.

Initial tests allocating memory with flags = 0×08 (ADDR_0, presumably request physical address rather than logical partition address) result in a status of LV1_DUPLICATE_ENTRY (-7). This and the previous return value of -6 suggest an association with a database of some kind (repository values or memory maps?). It appears that some form of allocation may be taking place as LV1_ILLEGAL_PARAMETER_VALUE and LV1_RESOURCE_SHORTAGE are reported for invalid input parameters, rather than LV1_DUPLICATE_ENTRY.

For all successful allocations so far, output muid (R5) = 1

lv1_write_htab_entry

Write an entry to the hash page table.

Kernel Call

result = lv1_write_htab_entry( /*IN*/ vas_id, slot, va, pa );

Parameters

Inputs
Register	Description
R3	vas_id - virtual address space id (0 for current)
R4	slot - table slot to write entry to
R5	va - first half of PTE
R6	pa - second half of PTE, except RPN is replaced with LPAR address
Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.

lv1_construct_virtual_address_space

Construct a PPE virtual address space.

Kernel Call

result = lv1_construct_virtual_address_space( /*IN*/ htab_size, number_of_sizes, page_sizes, /*OUT*/ &vas_id, &act_htab_size );

Parameters

Inputs
Register	Description
R3	htab_size - must be 18, 19 or 20 (256KB, 512KB or 1MB)
R4	number_of_sizes - How many page sizes are specified in page_sizes
R5	page_sizes - see notes
Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.
R4	vas_id - virtual address space id
R5	act_htab_size - actual hash table size?

Notes:

Page sizes are specified as the power of two for the desired sizes. Each power of two is stored as an 8 bit field in page_sizes, starting from the MSB.

The “pages_sizes” parameter is set in “mm.c” using the following function:

page_sizes = make_page_sizes(PAGE_SHIFT_16M, PAGE_SHIFT_64K);

static unsigned long make_page_sizes(unsigned long a, unsigned long b)
{
	return (a << 56) | (b << 48);
}

lv1_invalidate_htab_entries

Not used in current kernel.

Abstract Call

result = lv1_invalidate_htab_entries( /*IN*/ p1, p2, p3, p4, p5 );

Parameters

Inputs
Register	Description
R3	p1 - Unknown
R4	p2 - Unknown
R5	p3 - Unknown
R6	p4 - Unknown
R7	p5 - Unknown
Outputs
Register	Description
R3	Status?

lv1_get_virtual_address_space_id_of_ppe

Returns the virtual address space id of the PPE.

Kernel Call

result = lv1_get_virtual_address_space_id_of_ppe( /*IN*/ ppe_id , /*OUT*/ &vas_id );

Parameters

Inputs
Register	Description
R3	PPE id
Outputs
Register	Description
R3	status: 0 = LV1_SUCCESS
R4	vas_id - virtual address space id of the PPE
R5	htab_size_log2 - 18, 19 or 20 (256KB, 512KB or 1MB)
R6	number_of_sizes - How many page sizes are specified in page_sizes
R7	page_sizes - see lv1_construct_virtual_address_space

Notes:

Regardless of the ppe_id, when called from kernel module init function, vas_id always seems to be 11.

lv1_query_logical_partition_address_region_info

Retrieve address region information for the specified logical partition address region.

Kernel Call

result = lv1_query_logical_partition_address_region_info( /*IN*/ 0,
   /*OUT*/ &start_address, &size, &access_right, &max_page_size, &flags);

Parameters

Inputs
Register	Description
R3	0 - logical partition address region (lpar)
Outputs
Register	Description
R3	status: 0 = LV1_SUCCESS
R4	start_address - start address of logical partition address region
R5	size - size of logical partition address region
R6	access_right - ?
R7	max_page_size - maximum page size of logical partition address region? or order of the allocation?
R8	flags - ?

Notes:

Only the “max_page_size” parameter is currently used by the Kernel, in “mm.c”

Test Results

Register	Hex	Decimal	Comment
R3	0x00000000	(0)	value does not seem to effect result
Outputs
R3	0×00000000	(0)	LV1_SUCCESS
R4	0×00000000	(0)	start_address
R5	0×08000000	(134217728)	size - 128 Mb
R6	0×00000003	(3)	access_right
R7	0x0000001b	(27)	max_page_size
R8	0×00000008	(8)	flags

This suggests lpar 0 is a special lpar representing the first 128MB of RAM that are always available at boot time. In this case, max_page_size seems to correspond to the order of the allocation (2**27 = 128 MB). The meaning of access_right and flags is unknown.

Also works on a lpar obtained from lv1_allocate_memory, for example

lv1_allocate_memory(4096 /* size */, 12 /* page size */, 0, 0, &lpar, &muid);
lv1_query_logical_partition_address_region_info(lpar, &start_address, &size, &access_right, &max_page_size, &flags);

returns:

Register	Hex	Decimal	Comment
R3	0x30000001f00	(3298534891264)	lpar obtained from lv1_allocate_memory
Outputs
R3	0×00000000	(0)	LV1_SUCCESS
R4	0×30000001f00	(0)	start_address (same as input lpar)
R5	0×00001000	(4096)	size - 4kB
R6	0×00000003	(3)	access_right
R7	0x0000000c	(12)	max_page_size
R8	0×00000000	(0)	flags

lv1_select_virtual_address_space

Select an alternative virtual address space.

Kernel Call

result = lv1_select_virtual_address_space( /*IN*/ vas_id );

Parameters

Inputs
Register	Description
R3	vas_id - virtual address space id
Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.

Notes:

In “mm.c” When destructing a virtual address space, a call to select address space 0 (default?) is performed first.

Calling lv1_select_virtual_address_space(0) from a kernel module init function causes the PS3 to hang.

lv1_undocumented_function_8

Returns current HV uptime. (NOTE: Use graf's work here)

lv1_pause

Called during the Kernel idle loop - puts the PPE thread into an inactive state.

Kernel Call

result = lv1_pause( /*IN*/ mode );

Parameters

Inputs
Register	Description
R3	mode: 0 = wake on DEC interrupt, 1 = ignore DEC interrupt
Outputs
Register	Description
R3	status: 0 = LV1_SUCCESS, -17 = LV1_ILLEGAL_PARAMETER_VALUE

Notes:

LV1_ILLEGAL_PARAMETER_VALUE is returned for values of “mode” other than 0 or 1.

Comment from setup.c

/*
* lv1_pause() puts the PPE thread into inactive state until an
* irq on an unmasked plug exists. MSR[EE] has no effect.
* flags: 0 = wake on DEC interrupt, 1 = ignore DEC interrupt.
*/

lv1_destruct_virtual_address_space

Destruct a virtual address space.

Kernel Call

lv1_destruct_virtual_address_space( /*IN*/ vas_id );

Parameters

Inputs
Register	Description
R3	vas_id - virtual address space id
Outputs
Register	Description
R3	Status?

Notes:

Called with 0 in R3 crashes my PS3. Light turns red, appears to be off

lv1_configure_irq_state_bitmap

Register the address of a HV plug-outlet bitmap with the Hypervisor.

Kernel Call

result = lv1_configure_irq_state_bitmap( /*IN*/ ppe_id, cpu_id, bmp_addr );

Parameters

Inputs
Register	Description
R3	ppe_id - PPE id
R4	cpu_id - PPE CPU id
R5	bmp_addr - lpar address of state bitmap
Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.

Notes:

Comment from interrupt.c:

/**
* The HV mantains per SMT thread mappings of HV outlet to HV plug on
* behalf of the guest.  These mappings are implemented as 256 bit guest
* supplied bitmaps indexed by plug number.  The addresses of the bitmaps
* are registered with the HV through lv1_configure_irq_state_bitmap().
* The HV requires that the 512 bits of status + mask not cross a page
* boundary.  PS3_BMP_MINALIGN is used to define this minimal 64 byte
* alignment.
*
* The HV supports 256 plugs per thread, assigned as {0..255}, for a total
* of 512 plugs supported on a processor.  To simplify the logic this
* implementation equates HV plug value to Linux virq value, constrains each
* interrupt to have a system wide unique plug number, and limits the range
* of the plug values to map into the first dword of the bitmaps.  This
* gives a usable range of plug values of  {NUM_ISA_INTERRUPTS..63}.  Note
* that there is no constraint on how many in this set an individual thread
* can acquire.
*/

lv1_connect_irq_plug_ext

Connect a HV outlet to a CPU and virtual irq.

Kernel Call

result = lv1_connect_irq_plug_ext( /*IN*/ ppe_id, cpu_id, virq, outlet, 0 );

Parameters

Inputs
Register	Description
R3	ppe_id - PPE id
R4	cpu_id - PPE CPU id
R5	virq - virtual irq
R6	outlet - HV outlet
R7	0 - unknown
Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.

lv1_release_memory

Releases a previously allocated memory region. Return code is not checked.

Kernel Call

lv1_release_memory( /*IN*/ base );

Parameters

Inputs
Register	Description
R3	base - base address of memory region
Outputs
Register	Description
R3	Status??

lv1_put_iopte

Put an io page table entry.

Kernel Call

result = lv1_put_iopte( /*IN*/ ioas_id, ioif_addr, lpar_addr, io_id, flags );

Parameters

Inputs
Register	Description
R3	ioas_id - io address space id
R4	ioif_addr - io interface address
R5	lpar_addr - logical partition address
R6	io_id - io id
R7	flags - see notes
Outputs
Register	Description
R3	Status??

Notes:

Code taken from kboot-10\dl\linux-2.6.16\sound\powerpc\snd_ps3pf.c (kboot-20061208)

ret64 = lv1_put_iopte(0, /* io address space id */
   ioif_map_info_array[current_segment].ioif_addr + current_page * IO_PAGESIZE, /* ioif addr */
   p_to_lp(current_paddr), /* lpar addr */
   PS3PF_AUDIO_IOID, IOPTE_READONLY | IOPTE_COHERENT | IOPTE_STRICT_ORDER);

lv1_disconnect_irq_plug_ext

Disconnect a virtual irq from its HV outlet.

Kernel Call

lv1_disconnect_irq_plug_ext( /*IN*/ ppe_id, cpu_id, virq );

Parameters

Inputs
Register	Description
R3	ppe_id - PPE id
R4	cpu_id - PPE CPU id
R5	virq - virtual irq
R7	flags - see notes
Outputs
Register	Description
R3	Status?

lv1_construct_event_receive_port

Creates an outlet that can be used with a virtual irq to receive system events.

Kernel Call

result = lv1_construct_event_receive_port( /*OUT*/ &outlet );

Parameters

Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.
R4	outlet - event outlet

lv1_destruct_event_receive_port

Destruct a previously constructed event receiving port.

Kernel Call

result = lv1_destruct_event_receive_port( /*IN*/ outlet );

Parameters

Inputs
Register	Description
R3	outlet - event outlet
Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.

lv1_send_event_locally

Signal the specified event.

Kernel Call

result = lv1_send_event_locally( /*IN*/ outlet );

Parameters

Inputs
Register	Description
R3	outlet - event outlet
Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.

lv1_detect_pending_interrupts

Not used in current kernel. Used in ps2_gxemu.

Abstract Call

result = lv1_detect_pending_interrupts( /*IN*/ p1, /*OUT*/ &v1, &v2, &v3, &v4 );

Parameters

Inputs
Register	Description
R3	p1 - unknown (only 0 value is supported)
Outputs
Register	Description
R3	Status
R4	v1 - irq_bitmap[0]
R5	v2 - irq_bitmap[1]
R6	v3 - irq_bitmap[2]
R7	v4 - irq_bitmap[3]

Notes:
Return 256 bit irq bitmap for previously connected irq plugs (using lv1_connect_irq_plug).
Info taken from kboot-10\dl\linux-2.6.16\include\asm-powerpc\lv1calltab.h (kboot-20061208)

lv1_end_of_interrupt

Indicate the end of an interrupt handler has been reached.

kboot Call

result = lv1_end_of_interrupt( /*IN*/ irq );

Parameters

Inputs
Register	Description
R3	irq - interrupt number
Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.

Notes:

Comment in kboot-10\dl\linux-2.6.16\arch\powerpc\platforms\ps3pf\pic.c (kboot-20061208)

/* 
 lv1_end_of_interrupt must be called at end_irq. 
 Some lv1 drivers clear irq status in it.
*/

lv1_connect_irq_plug

Bind a virtual interrupt to a CPU.

kboot Call

result = lv1_connect_irq_plug( /*IN*/ virq, hwirq );

Parameters

Inputs
Register	Description
R3	virq - virtual interrupt
R4	hwirq - hardware interrupt
Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.

Notes:

Info taken from kboot-10/dl/linux-2.6.16/patches/cell-support/2.6.19-rc6-arnd1/ps3-support/ps3-interrupt.patch (kboot-20061208)

lv1_disconnect_irq_plug

Unbind a virtual interrupt from a CPU.

kboot Call

lv1_disconnect_irq_plug( /*IN*/ virq );

Parameters

Inputs
Register	Description
R3	virq - virtual interrupt
Outputs
Register	Description
R3	Status?

Notes:

Info taken from kboot-10/dl/linux-2.6.16/patches/cell-support/2.6.19-rc6-arnd1/ps3-support/ps3-interrupt.patch (kboot-20061208)

lv1_end_of_interrupt_ext

Indicate that the end of an interrupt handler has been reached.

Kernel Call

lv1_end_of_interrupt_ext( /*IN*/ ppe_id, cpu_id, virq );

Parameters

Inputs
Register	Description
R3	ppe_id - PPE id
R4	cpu_id - PPE CPU id
R5	virq - virtual irq
Outputs
Register	Description
R3	Status?

lv1_did_update_interrupt_mask

Indicate that CPU interrupt mask has been updated.

Kernel Call

lv1_did_update_interrupt_mask( /*IN*/ ppe_id, cpu_id );

Parameters

Inputs
Register	Description
R3	ppe_id - PPE id
R4	cpu_id - PPE CPU id
Outputs
Register	Description
R3	Status?

lv1_shutdown_logical_partition

Not used in current kernel.

Abstract Call

result = lv1_shutdown_logical_partition( /*IN*/ p1 );

Parameters

Inputs
Register	Description
R3	p1 - shutdown command (see notes)
Outputs
Register	Description
R3	Status?

Notes:

Comment from kboot-10/dl/linux-2.6.16/include/asm-powerpc/lv1call.h (kboot-20061208)

/* values for lv1_shutdown_logical_partition */
#define LV1_SHUTDOWN_LP_HALT		1
#define LV1_SHUTDOWN_LP_POWER_OFF	2
#define LV1_SHUTDOWN_LP_RESTART	3

lv1_destruct_logical_spe

Destructs a logical SPE.

Kernel Call

result = lv1_destruct_logical_spe( /*IN*/ spe_id );

Parameters

Inputs
Register	Description
R3	spe_id - spe id
Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.

lv1_construct_logical_spe

Constructs a logical SPE.

Kernel Call

status = lv1_construct_logical_spe( /*IN*/ PAGE_SHIFT, PAGE_SHIFT, PAGE_SHIFT, PAGE_SHIFT, PAGE_SHIFT, vas_id, SPE_TYPE_LOGICAL,
		/*OUT*/ &priv2_addr, &problem_phys, &local_store_phys, &unused, &shadow_addr, &spe_id );

Parameters

R3

Inputs
Register	Description
R3	PAGE_SHIFT
R4	PAGE_SHIFT
R5	PAGE_SHIFT
R6	PAGE_SHIFT
R7	PAGE_SHIFT
R8	vas_id - virtual address space id
R9	SPE_TYPE_LOGICAL (0)
Outputs
Register	Description
Status - 0 = OK, Other values are unknown, but indicate failure.
R4	priv2_addr - lpar address of spe priv2 area
R5	problem_phys - lpar address of spu_problem area
R6	local_store_phys - lpar address of spu local storage
R7	unused
R8	shadow_addr - lpar address of spe register shadow area
R9	spe_id - logical spe id

Notes:

R7 out parameter was referred to in a previous codebase as “ctxt_addr”.

Test Results

priv2_addr	problem_phys	local_store_phys	unused	shadow_addr	spe_id
0x4c0000660000	0x4c0000640000	0x4c0000600000	0×0	0x30000000d000	11
0x4c0000760000	0x4c0000740000	0x4c0000700000	0×0	0x30000000f000	15
0x4c0000860000	0x4c0000840000	0x4c0000800000	0×0	0×300000011000	19
0x4c0000960000	0x4c0000940000	0x4c0000900000	0×0	0×300000013000	23
0x4c0000a60000	0x4c0000a40000	0x4c0000a00000	0×0	0×300000015000	27
0x4c0000b60000	0x4c0000b40000	0x4c0000b00000	0×0	0×300000017000	31

For each entry, only two separate lpar are allocated by the hypervisor. Indeed, calling lv1_query_logical_partition_address_region_info on priv2_addr, problem_phys, local_store_phys and shadow_addr for the first entry returns the following info:

0x4c0000660000

lpar	start_address	size	access_right	max_page_size	flags	comment
0x4c0000600000	524288	0×3 (RW)	12	0xa000000000000000	SPU MMIO lpar, privilege state 2 region (128kB)
0x4c0000640000	0x4c0000600000	524288	0×3 (RW)	12	0xa000000000000000	SPU MMIO lpar, problem state region (128kB)
0x4c0000600000	0x4c0000600000	524288	0×3 (RW)	12	0xa000000000000000	SPU MMIO lpar, local store region (256kB)
0x30000000d000	0x30000000d000	4096	0×1 (RO)	12	0xa000000000000000	SPU shadow registers lpar (4kB, read-only)

From this info we see a single lpar is used for all the SPU MMIO region (see figure 5-1 CBE Memory Map of the Cell Broadband Engine Programming Handbook) and another lpar is used for the SPE registers.

lv1_set_spe_interrupt_mask

Set the interrupt mask of a specific spe.

Kernel Call

lv1_set_spe_interrupt_mask( /*IN*/ spe_id, class, mask );

Parameters

Inputs
Register	Description
R3	spe_id - spe id
R4	class - spe interrupt class
R5	mask - spe interrupt mask
Outputs
Register	Description
R3	Status?

lv1_undocumented_function_62

SPE (isolation, it updates a SLB entry, writes to SLB_Index, SLB_VSID, SLB_ESID and SLB_Invalidate_Entry registers)

lv1_set_slb_for_logical_spu

Exists in PAL 1.7; Returned -4 (LV1_DENIED_BY_POLICY) when passed 0 in R3 to R10.

lv1_undocumented_function_63

Does not exist in 3.15.

Exists in PAL 1.7; Returned -4 (LV1_DENIED_BY_POLICY) when passed 0 in R3 to R10.

lv1_set_spe_transition_notifier

Not used in current kernel.

Abstract Call

result = lv1_set_spe_transition_notifier( /*IN*/ p1, p2, p3 );

Parameters

Inputs
Register	Description
R3	spe_id - logical spe id
R4	0 - Unknown usage
Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.

lv1_disable_logical_spe

Disables a logical SPE.

Kernel Call

result = lv1_disable_logical_spe( /*IN*/ spe_id, 0 );

Parameters

Inputs
Register	Description
R3	spe_id - logical spe id
R4	0 - Unknown usage
Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.

lv1_clear_spe_interrupt_status

Clear the interrupt status of a specific spe.

Kernel Call

lv1_clear_spe_interrupt_status( /*IN*/ spe_id, class, stat, 0 );

Parameters

Inputs
Register	Description
R3	spe_id - logical spe id
R4	class - spe interrupt class
R5	stat - new interrupt status?
R6	0 - Unknown
Outputs
Register	Description
R3	Status?

lv1_get_spe_interrupt_status

Get the interrupt status of a specific spe.

Kernel Call

lv1_get_spe_interrupt_status( /*IN*/ spe_id, class, /*OUT*/ &stat );

Parameters

Inputs
Register	Description
R3	spe_id - logical spe id
R4	class - spe interrupt class
Outputs
Register	Description
R3	Status?
R4	stat - interrupt status

lv1_get_logical_ppe_id

Returns the logical PPE id.

Kernel Call

status = lv1_get_logical_ppe_id( /*OUT*/ &ppe_id );

Parameters

Outputs
Register	Description
R3	Status?
R4	logical PPE id

Notes:

When called from kernel module init function, ppe_id always seem to be 1.

lv1_set_interrupt_mask

Not used in current kernel.

Abstract Call

result = lv1_set_interrupt_mask( /*IN*/ p1, p2, p3, p4, p5 );

Parameters

Inputs
Register	Description
R3	p1 - Unknown
R4	p2 - Unknown
R5	p3 - Unknown
R6	p4 - Unknown
R7	p5 - Unknown
Outputs
Register	Description
R3	Status?

lv1_get_logical_partition_id

Called during Kernel setup.

The single output parameter, logical partition id, is later used as a parameter to call other Hypervisor functions.

Kernel Call

result = lv1_get_logical_partition_id(/*OUT*/ &lp_id );

Parameters

Outputs
register	Description
R3	result: 0 = LV1_SUCCESS
R4	lp_id - logical partition id

Notes:

When called from kernel module init function, lp_id always seems to be 2.

The “read_node” function contained in “repository.c” is passed a parameter, lpar_id (logical partition id). If lpar_id is equal to PS3_LPAR_ID_CURRENT (0) then lv1_get_logical_partition_id is called to retrieve the current logical partition id. Any other value for lpar_id is passed directly to the following HV calls, though the only other value in use appears to be PS3_LPAR_ID_PME (1)

lv1_undocumented_function_75

Exists in PAL 1.7; Returned 0 (LV1_SUCCESS) when passed 0 in R3 to R10.

lv1_configure_execution_time_variable

Not used in current kernel.

Abstract Call

result = lv1_configure_execution_time_variable( /*IN*/ p1 );

Parameters

Inputs
Register	Description
R3	p1 - Unknown
Outputs
Register	Description
R3	Status?

lv1_get_spe_irq_outlet

Get an IRQ outlet of a certain class from the specified SPE.

Kernel Call

result = lv1_get_spe_irq_outlet( /*IN*/ spe_id, class, /*OUT*/ &outlet );

Parameters

Inputs
Register	Description
R3	spe_id - logical spe id
R4	class - spe interrupt class (0, 1 or 2)
Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.
R4	outlet - irq outlet

SPE Interrupt Class:

Class	Description	Examples
0	Errors	SPE errors, DMA errors, DMA alignment errors
1	DMA translation exceptions	MFC page faults, segment faults
2	Application events	SPE stop and signal, DMA completion interrupt, mailbox interrupts

lv1_set_spe_privilege_state_area_1_register

Sets a register in SPE privilege area 1.

Kernel Call

lv1_set_spe_privilege_state_area_1_register( /*IN*/ spe_id, offset, value );

Parameters

Inputs
Register	Description
R3	spe_id - spe id
R4	offset - register offset, 0, 0x600, 0x710, 0x808, 0x820
R5	value - register value
Outputs
Register	Description
R3	Status?

lv1_undocumented_function_89

SPE (writes to MFC_TLB_Invalidate_Entry register)

Exists in PAL 1.7; Returned -6 (LV1_NO_ENTRY) when passed 0 in R3 to R10.

lv1_create_repository_node

The repository appears to be an area of storage for use by the Hypervisor.

Abstract Call

status = lv1_create_repository_node(/*IN*/ n1, n2, n3, n4, v1, v2 );

Parameters

Inputs
Register	Description
R3	top level key
R4	2nd level key
R5	3rd level key
R6	4th level key
R7	value 1
R8	value 2
Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.

Notes:

This call is not used within the current Kernel, so the parameter list is based on speculation. It will still return 0 if the specified node already exists, and it will not change current data.

See “lv1_get_repository_node_value” for an example of actual key/value usage within the Kernel.

lv1_get_repository_node_value

The repository appears to be an area of storage for use by the Hypervisor. 256-bit keys are used to reference 128-bit values stored in the repository. Functions exist to create, get, modify and remove repository nodes.

See notes below for usage speculation.

Kernel Call

status = lv1_get_repository_node_value(/*IN*/ lpar_id, n1, n2, n3, n4 /*OUT*/ &v1, &v2 );

Parameters

Inputs
Register	Description
R3	logical partion id
R4	top level key
R5	2nd level key
R6	3rd level key
R7	4th level key
Outputs
Register	Description
R3	Status: 0 = OK, -6 = LV1_NO_ENTRY
R4	value 1
R5	value 2

Notes:

The logical partition id is also required as an input parameter to get a repository node value, but this parameter does not appear to be passed when creating, modifying or removing nodes.

There are instances in the Kernel code where the keys are constructed from string values, which appear to follow a 4-level key/subkey hierarchy.

Test Results

Calling lv1_get_repository_node_value for the node ‘bi.pu.#1.rm_size’ produces the following result:

bi.pu.(1).rm_size - Real mode memory size
Register	Hex Value	Value	Comment
R3	0000000000000002	(2)	PS3_LPAR_ID_CURRENT
R4	0000000062690000	....bi..	boot info?
R5	7075000000000000	pu......	processor unit
R6	0000000000000001	........	pu id (1)
R7	726d5f73697a6500	rm_size.	real mode size
Outputs
R3	0000000000000000	(0)	LV1_SUCCESS
R4	0000000008000000	(134217728)	128 Mb
R5	0000000000000000	(0)

Other nodes referenced in “repository.c”:

lpar_id = PS3_LPAR_ID_CURRENT (0×2)
Node	v1	v2	Comment
bi.spun.#0.#0	0000000000000006 (6)	0 (0)	number of physical spus reserved
bi.spursvn.#0.#0	0000000000000006 (6)	0 (0)	number of spu resource reservations
bi.spursv.(0..5).#0	8000000000000000 (PS3_SPU_RESOURCE_TYPE_EXCLUSIVE)	(0..5)	spu resource reservation id value
bi.boot_dat.address.#0	0000000007fff000 (134213632)	0 (0)	boot data address
bi.boot_dat.size.#0	0000000000000800 (2048)	0 (0)	boot data size
bi.pu.(1).rm_size	0000000008000000 (134217728)	0 (0)	real mode limit
bi.rgntotal.#0.#0	000000000f800000 (260046848)	0 (0)	max memory size

lpar_id = PS3_LPAR_ID_PME (0×1)
Node	v1	v2	Comment
ben.#0.#0.#0	0000000000000001 (1)	0000000000000000 (0)	Unused - in function “ps3_repository_read_num_be”
be(0).#0.#0.#0	0000000000000000 (0)	0000000000000000 (0)	be node id (used to retrieve clock freq)
be.(0).clock.#0	0000000004c1a6c0 (79800000)	0000000000000000 (0)	decrementer frequency (3.2 Ghz / 40)

lpar_id = PS3_LPAR_ID_PME (0×1) - FW 3.15 PAL 60GB PS3, First Generation (Fat)
Node	v1	v2	Comment
sys.flash.fmt.#0	00000000000001 (1)	00000000000000 (0)	Flash format. v1: 1 = NAND , 2 = VFLASH?
sys.hw.config.#0	20000000fffffeff	00000000000000 (0)	0×20000000000000 mask + something
sys.flash.ext.#0	000000000000ff (255)	00000000000000 (0)	–
plat.id.#0.#0	436f6b4231300000 (ASCII‘CokB10’)	00000000000000 (0)	Platform ID
sys.ac.sd.#0	00000000000000 (0)	00000000000000 (0)	System Debug Flag
sys.flash.boot.#0	00000000000000 (0)	00000000000000 (0)	–
be.0.lpm.priv	00000000000002 (2)	00000000780101 (7864577)	–
rsx.rdcy.1.#0	ffff0d020a02ffff	00000000000000 (0)	–
rsx.rdcy.2.#0	ffffffffffffffff	00000000000000 (0)	–
rsx.rdcy.3.#0	00000000000000 (0)	00000000000000 (0)	–
rsx.rdcy.4.#0	00000000000000 (0)	00000000000000 (0)	–
rsx.rdcy.5.#0	00000000000000 (0)	00000000000000 (0)	–
rsx.rdcy.6.#0	00000000000000 (0)	00000000000000 (0)	–
rsx.rdcy.7.#0	00000000000000 (0)	00000000000000 (0)	–
rsx.rdcy.8.#0	00000000000000 (0)	00000000000000 (0)	–
mu.1.size.#0	00000010000000 (268435456)	00000000000000 (0)	–
be.0.tb_clk.#0	00000004c1a6c0 (79800000)	00000000000000 (0)	–
be.0.nclk.#0	000000be420e00 (3192000000)	00000000000000 (0)	–
ios.net.eurus.lpar	00000000000000 (0)	00000000000000 (0)	–
sys.syscon.pversion.#0	00000000000001 (1)	00000000000000 (0)	–
sys.param.load.rom1st	00000000000001 (1)	00000000000000 (0)	–
lv1.maxplgid.#0.#0	00000000000100 (256)	00000000000000 (0)	–
lv1.specver.#0.#0	00000300010005	00000000000000 (0)	Matches firmware 3.1.5
lv1.buildid.#0.#0	00000000000000 (0)	00000000000000 (0)	–
lv1.ts.size.#0	00000000000000 (0)	00000000000000 (0)	–
lv1.ts.start.#0	00000010000000 (268435456)	00000000000000 (0)	–

lv1_modify_repository_node_value

The repository appears to be an area of storage for use by the Hypervisor.

Abstract Call

status = lv1_modify_repository_node_value(/*IN*/ n1, n2, n3, n4, v1, v2 );

Parameters

Inputs
Register	Description
R3	top level key
R4	2nd level key
R5	3rd level key
R6	4th level key
R7	value 1
R8	value 2
Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.

Parameter list based on speculation. Not used in current Kernel.

lv1_remove_repository_node

The repository appears to be an area of storage for use by the Hypervisor.

Abstract Call

status = lv1_remove_repository_node( /*IN*/ n1, n2, n3, n4 );

Parameters

Inputs
Register	Description
R3	top level key
R4	2nd level key
R5	3rd level key
R6	4th level key
Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.

Parameter list based on speculation. Not used in current Kernel.

lv1_read_htab_entries

Not used in current Kernel.

Abstract Call

result = lv1_read_htab_entries( /*IN*/ p1, p2, /*OUT*/ &v1, &v2, &v3, &v4, &v5 );

Parameters

Inputs
Register	Description
R3	p1 - vas_id
R4	p2 - offset
Outputs
Register	Description
R3	Status?
R4	v1 - unknown
R5	v2 - unknown
R6	v3 - unknown
R7	v4 - unknown
R8	v5 - unknown

Notes: offset is 64-bit indexed. r4-r7 seem to be right from the htab. r8 is 16-bit indexed reading from something 0xFFFB is max offset

lv1_set_dabr

Sets dabr (Data Address Breakpoint Register) and dabrx (Data Address Breakpoint Register Extension)

Kernel Call

result = lv1_set_dabr( /*IN*/ dabr, dabrx);

Parameters

Inputs
Register	Description
R3	dabr - see notes
R4	dabrx - see notes
Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.

Notes:

DABR:

Bit(s) Name Description
0:60   DAB  Data Address Breakpoint
61     BT   Breakpoint Translation
62     DW   Data Write
63     DR   Data Read

DABRX

Bit(s) Name  Description
0:59         Reserved
60     BTI   Breakpoint Translation Ignore
61:63  PRIVM Privilege Mask
61     HYP   Hypervisor state - unsupported in LV1
62     PNH   Privileged but Non-Hypervisor state
63     PRO   Problem state

When PRIVM in dabrx is 0 or when any unsupported or reserved bit in dabrx is active, both dabr and dabrx writes are not performed and 0x2FFFFFFEF is returned.

DABRX is defined in “setup.c” as follows

enum {DABR_USER = 1, DABR_KERNEL = 2,};

lv1_set_vmx_graphics_mode

Set the Single Precision mode of the vmx graphics units in the PPU

Abstract Call

result = lv1_set_vmx_graphics_mode( mode );

Parameters

Inputs
Register	Description
R3	mode - 0 = IEEE 754-1985 SIMD rounding mode for VMX/Altivec Instructions
	mode - 1 = SPE-compatible SIMD graphics-rounding mode for VMX/Altivec Instructions
Outputs
Register	Description
R3	result: 0 = LV1_SUCCESS, -17 = LV1_ILLEGAL_PARAMETER_VALUE

Notes:

This is a call to set the single precision rounding mode of the VMX units in the Cell PPUs. The AltiVec/VMX SIMD/Vector processing unit has 2 rounding modes for dealing with Single-precision floating-point. IEEE 754-1985 and SPE-compatible SIMD graphics-rounding mode.

The Cell Broadband Engine Programming Handbook has this to say on the subject: The first implementation of the Cell Broadband Engine Architecture (CBEA) (the CBE processor) supports instructions with a graphics rounding mode. This mode allows programs written with vector/SIMD multimedia extension instructions to produce floating-point results that are equivalent in precision to those written in the SPU instruction set. In this mode, as in the SPU environment, the default rounding mode is round to zero, denormals are treated as zero, and there are no infinities or NaNs.

This call change bit 12 (known as grap_md or grap_mode in various documents) in the HID1 register. Hardware Implementation Register 1 is a HV privileged resource, hence to change the mode from Supervisor mode requires a HV call.

Reference Documents: Cell Broadband Engine Programming Handbook V1.1 Cell Broadband Engine Registers V1.5

Tests:

Info taken from kboot-10\dl\linux-2.6.16\include\asm-powerpc\lv1calltab.h (kboot-20061208)

When recompiled into Kernel module init function, accepts values of 0 and 1 for p1. All other values return -17 (LV1_ILLEGAL_PARAMETER_VALUE)

lv1_set_thread_switch_control_register

Not used in current Kernel.

Abstract Call

result = lv1_set_thread_switch_control_register( /*IN*/ p1 );

Parameters

Inputs
Register	Description
R3	p1 - Unknown
Outputs
Register	Description
R3	Status?

Notes:

Info taken from kboot-10\dl\linux-2.6.16\include\asm-powerpc\lv1calltab.h (kboot-20061208)

lv1_authenticate_program_segment

previous alias: lv1_undocumented_function_99

SPE (isolation, syscall 0x10043, syscall 0x10042, syscall 0x1004A)

Exists in PAL 1.7; Returned -4 (LV1_DENIED_BY_POLICY) when passed 0 in R3 to R10.

lv1_undocumented_function_102

Returns current TB ticks

Exists in PAL 1.7; Returned 0 (LV1_SUCCESS) and R4 = 0x692F5D1E7h when passed 0 in R3 to R10.

lv1_get_total_execution_time

Not used in current kernel. Does not exist in 3.15 HV dump.

Abstract Call

result = lv1_get_total_execution_time( /*IN*/ p1, p2, /*OUT*/ &v1 );

Parameters

Inputs
Register	Description
R3	p1 - Unknown
R4	p2 - Unknown
Outputs
Register	Description
R3	Status?
R4	v1 - Unknown

Notes:

I always get LV1_NOT_IMPLEMENTED

lv1_undocumented_function_105

Exists in PAL 1.7. Returns -17 (LV1_ILLEGAL_PARAMETER_VALUE, 0, 0, C000000000537EF8h, F09B89AF5001h, 6C0061D8E190h, C0000000008DF718h, F09B89AF5001h, when passed 0 in R3 to R10.

lv1_undocumented_function_106

Exists in PAL 1.7. Returns the same as lv1_undocumented_function_105.

lv1_undocumented_function_107

Exists in PAL 1.7. Returns the same as lv1_undocumented_function_105.

lv1_undocumented_function_108

Exists in PAL 1.7. Returns the same as lv1_undocumented_function_105.

lv1_undocumented_function_109

Exists in PAL 1.7. Returns the same as lv1_undocumented_function_105.

lv1_read_remote_file

Parameters

Inputs
Register	Description
R3	u32 type
R4	u32 *path
R5	u64 offset
R6	u32 *buf
R7	u64 size
Outputs
Register	Description
R3	status
R4	n_read

lv1_write_remote_file

Parameters

Inputs
Register	Description
R3	u32 type
R4	u32 *path
R5	u64 offset
R6	u32 *buf
R7	u64 size
Outputs
Register	Description
R3	status
R4	n_write

lv1_get_remote_file_size

Parameters

Inputs
Register	Description
R3	u32 type
R4	u32 *path
Outputs
Register	Description
R3	status
R4	file_size

----

lv1_map_physical_address_region

Parameters

Inputs
Register	Description
R3	start -
R4	page_size -
R5	size -
Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.
R4	lpar_addr -

lv1_unmap_physical_address_region

Parameters

Inputs
Register	Description
R3	lpar_addr -
Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.

lv1_allocate_io_segment

Allocate an io segment.

kboot Call

result = lv1_allocate_io_segment( /*IN*/ ioas_id, segment_size, io_page_size, /*OUT*/ &ioif_addr );

Parameters

Inputs
Register	Description
R3	ioas_id - io address space id
R4	segment_size - io segment size
R5	io_page_size - io page size, 0xC, 0×10, 0×14
Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.
R4	ioif_addr - io interface address

Notes:

Code taken from kboot-10\dl\linux-2.6.16\sound\powerpc\snd_ps3pf.c (kboot-20061208)

ret64 = lv1_allocate_io_segment(0,           /* io space */
   IO_SEGMENTSIZE, /* segment size */
   IO_PAGESIZE_SHIFT, /* io page size */
   &(ioif_map_info_array[current_segment].ioif_addr));

lv1_release_io_segment

Release an io segment.

kboot Call

result = lv1_release_io_segment( /*IN*/ ioas_id, ioif_addr );

Parameters

Inputs
Register	Description
R3	ioas_id - io address space id
R4	ioif_addr - io interface address
Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.

Notes:

Code taken from kboot-10\dl\linux-2.6.16\sound\powerpc\snd_ps3pf.c (kboot-20061208)

ret64 = lv1_release_io_segment(0, /* io space */
   ioif_map_info_array[current_segment].ioif_addr);

lv1_allocate_ioid

Not used in current kernel.

Abstract Call

result = lv1_allocate_ioid( /*IN*/ p1, /*OUT*/ &v1 );

Parameters

Inputs
Register	Description
R3	SBZ
Outputs
Register	Description
R3	Status?
R4	the ioid

Notes:

Info taken from kboot-10\dl\linux-2.6.16\include\asm-powerpc\lv1calltab.h (kboot-20061208)

lv1_release_ioid

Not used in current Kernel.

Abstract Call

result = lv1_release_ioid( /*IN*/ p1, p2 );

Parameters

Inputs
Register	Description
R3	p1 - Unknown
R4	p2 - Unknown
Outputs
Register	Description
R3	Status?

Notes:

Info taken from kboot-10\dl\linux-2.6.16\include\asm-powerpc\lv1calltab.h (kboot-20061208)

lv1_construct_io_irq_outlet

Construct an outlet for a non-virtualized device interrupt.

Kernel Call

result = lv1_construct_io_irq_outlet( /*IN*/ interrupt_id, /*OUT*/ &outlet );

Parameters

Inputs
Register	Description
R3	interrupt_id - interrupt id
Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.
R4	outlet - interrupt outlet

lv1_destruct_io_irq_outlet

Destruct a previously constructed device interrupt outlet.

Kernel Call

result = lv1_destruct_io_irq_outlet( /*IN*/ outlet );

Parameters

Inputs
Register	Description
R3	outlet - interrupt outlet
Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.

lv1_map_htab

Map the hash page table.

Kernel Call

result = lv1_map_htab( /*IN*/ 0, /*OUT*/ &htab_addr );

Parameters

Inputs
Register	Description
R3	0 - Unknown (lpid?)
Outputs
Register	Description
R3	Status?
R4	htab_addr - hash page table address

Notes:

In “htab.c” return code is assigned, but not used. Must be translated and ioremapped before it can be used in the kernel. It’s 1MB long

lv1_unmap_htab

Unmap the hash page table.

Kernel Call

lv1_unmap_htab( /*IN*/ htab_addr );

Parameters

Inputs
Register	Description
R3	htab_addr - hash page table address
Outputs
Register	Description
R3	Status?

lv1_read_remote_file_long_name

Parameters

Inputs
Register	Description
R3	u32 type
R4	u32 *path
R5	u32 path_len
R6	u64 offset
R7	u32 *buf
R8	u64 size
Outputs
Register	Description
R3	status
R4	n_read

lv1_write_remote_file_long_name

Parameters

Inputs
Register	Description
R3	u32 type
R4	u32 *path
R5	u32 path_len
R6	u64 offset
R7	u32 *buf
R8	u64 size
Outputs
Register	Description
R3	status
R4	n_write

lv1_get_remote_file_size_long_name

Parameters

Inputs
Register	Description
R3	u32 type
R4	u32 *path
R5	u32 path_len
Outputs
Register	Description
R3	status
R4	file_size

lv1_get_version_info

Returns PS3 firmware version information.

Kernel Call

result = lv1_get_version_info( /*OUT*/ &raw );

Parameters

Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.
R4	raw - firmware data (see notes)

Notes:

The firmware information is accessed using the following union:

union ps3_firmware_version {
	u64 raw;
	struct {
		u16 pad;
		u16 major;
		u16 minor;
		u16 rev;
	};
};

lv1_undocumented_function_134

Exists in PAL 1.7. Returns 0 when passed R3-R10=0.

lv1_undocumented_function_135

Exists in PAL 1.7. Returns -6 (LV1_NO_ENTRY) in R3, rest same as lv1_undocumented_function_105.

lv1_undocumented_function_136

Exists in PAL 1.7. Returns -6 (LV1_NO_ENTRY) in R3, rest same as lv1_undocumented_function_105.

lv1_undocumented_function_137

SPE

Exists in PAL 1.7. Returns -4 (LV1_DENIED_BY_POLICY) when passed 0 in R3-R10.

lv1_undocumented_function_138

SPE

Exists in PAL 1.7. Returns -4 (LV1_DENIED_BY_POLICY) when passed 0 in R3-R10.

lv1_construct_lpm

Not used in current kernel.

Abstract Call

result = lv1_construct_lpm( /*IN*/ p1, p2, p3, p4, p5, p6, /*OUT*/ &v1, &v2, &v3 );

Parameters

Inputs
Register	Description
R3	p1 - node_id, this is the node id of the processor, 0 is only valid value
R4	p2 - tb_type, 0 is none, 1 is internal
R5	p3 - Unknown, is 0
R6	p4 - Unknown, is 0
R7	p5 - tb_cache in lpar, 128 byte aligned
R8	p6 - tb_cache_size
Outputs
Register	Description
R3	Status
R4	v1 - lpm_id
R5	v2 - outlet_id
R6	v3 - tb_size

lv1_destruct_lpm

Not used in current kernel.

Abstract Call

result = lv1_destruct_lpm( /*IN*/ p1 );

Parameters

Inputs
Register	Description
R3	p1 - lpm_id
Outputs
Register	Description
R3	Status?

lv1_start_lpm

Not used in current kernel.

Abstract Call

result = lv1_start_lpm( /*IN*/ p1 );

Parameters

Inputs
Register	Description
R3	p1 - lpm_id
Outputs
Register	Description
R3	Status?

lv1_stop_lpm

Not used in current kernel.

Abstract Call

result = lv1_stop_lpm( /*IN*/ p1, /*OUT*/ &v1 );

Parameters

Inputs
Register	Description
R3	p1 - Unknown
Outputs
Register	Description
R3	Status?
R4	v1 - Unknown

lv1_copy_lpm_trace_buffer

Not used in current kernel.

Abstract Call

result = lv1_copy_lpm_trace_buffer( /*IN*/ p1, p2, p3 /*OUT*/ &v1 );

Parameters

Inputs
Register	Description
R3	p1 - lpm_id
R3	p2 - offset
R3	p3 - request
Outputs
Register	Description
R3	Status
R4	v1 - tmp

lv1_add_lpm_event_bookmark

Not in current kernel.

Abstract Call

result = lv1_add_lpm_event_bookmark( /*IN*/ p1, p2, p3, p4, p5 );

Parameters

Inputs
Register	Description
R3	p1 - Unknown
R3	p2 - Unknown
R3	p3 - Unknown
R6	p4 - Unknown
R7	p5 - Unknown
Outputs
Register	Description
R3	Status?

lv1_delete_lpm_event_bookmark

Not used in current kernel.

Abstract Call

result = lv1_delete_lpm_event_bookmark( /*IN*/ p1, p2, p3 );

Parameters

Inputs
Register	Description
R3	p1 - Unknown
R3	p2 - Unknown
R3	p3 - Unknown
Outputs
Register	Description
R3	Status?

lv1_set_lpm_interrupt_mask

Not used in current kernel.

Abstract Call

result = lv1_set_lpm_interrupt_mask( /*IN*/ p1, p2, p3, /*OUT*/ &v1 );

Parameters

Inputs
Register	Description
R3	p1 - Unknown
R3	p2 - Unknown
R3	p3 - Unknown
Outputs
Register	Description
R3	Status?
R4	v1 - Unknown

lv1_get_lpm_interrupt_status

Not used in current kernel.

Abstract Call

result = lv1_get_lpm_interrupt_status( /*IN*/ p1, /*OUT*/ &v1 );

Parameters

Inputs
Register	Description
R3	p1 - Unknown
Outputs
Register	Description
R3	Status?
R4	v1 - Unknown

lv1_set_lpm_general_control

Not used in current kernel.

Abstract Call

result = lv1_set_lpm_general_control( /*IN*/ p1, p2, p3, p4, p5, /*OUT*/ &v1, &v2 );

Parameters

Inputs
Register	Description
R3	p1 - Unknown
R4	p2 - Unknown
R5	p3 - Unknown
R6	p4 - Unknown
R7	p5 - Unknown
Outputs
Register	Description
R3	Status?
R4	v1 - Unknown
R5	v2 - Unknown

lv1_set_lpm_interval

Not used in current kernel.

Abstract Call

result = lv1_set_lpm_interval( /*IN*/ p1, p2, p3, /*OUT*/ &v1 );

Parameters

Inputs
Register	Description
R3	p1 - Unknown
R4	p2 - Unknown
R5	p3 - Unknown
Outputs
Register	Description
R3	Status?
R4	v1 - Unknown

lv1_set_lpm_trigger_control

Not used in current kernel.

Abstract Call

result = lv1_set_lpm_trigger_control( /*IN*/ p1, p2, p3, /*OUT*/ &v1 );

Parameters

Inputs
Register	Description
R3	p1 - Unknown
R4	p2 - Unknown
R5	p3 - Unknown
Outputs
Register	Description
R3	Status?
R4	v1 - Unknown

lv1_set_lpm_counter_control

Not used in current kernel.

Abstract Call

result = lv1_set_lpm_counter_control( /*IN*/ p1, p2, p3, p4, /*OUT*/ &v1 );

Parameters

Inputs
Register	Description
R3	p1 - Unknown
R4	p2 - Unknown
R5	p3 - Unknown
R6	p4 - Unknown
Outputs
Register	Description
R3	Status?
R4	v1 - Unknown

lv1_set_lpm_group_control

Not used in current kernel.

Abstract Call

result = lv1_set_lpm_group_control( /*IN*/ p1, p2, p3, /*OUT*/ &v1 );

Parameters

Inputs
Register	Description
R3	p1 - Unknown
R4	p2 - Unknown
R5	p3 - Unknown
Outputs
Register	Description
R3	Status?
R4	v1 - Unknown

lv1_set_lpm_debug_bus_control

Not used in current kernel.

Abstract Call

result = lv1_set_lpm_debug_bus_control( /*IN*/ p1, p2, p3, /*OUT*/ &v1 );

Parameters

Inputs
Register	Description
R3	p1 - Unknown
R4	p2 - Unknown
R5	p3 - Unknown
Outputs
Register	Description
R3	Status?
R4	v1 - Unknown

lv1_set_lpm_counter

Not used in current kernel.

Abstract Call

result = lv1_set_lpm_counter( /*IN*/ p1, p2, p3, p4, p5, /*OUT*/ &v1, &v2 );

Parameters

Inputs
Register	Description
R3	p1 - Unknown
R4	p2 - Unknown
R5	p3 - Unknown
R6	p4 - Unknown
R7	p5 - Unknown
Outputs
Register	Description
R3	Status?
R4	v1 - Unknown
R5	v2 - Unknown

lv1_set_lpm_signal

Not used in current kernel.

Abstract Call

result = lv1_set_lpm_signal( /*IN*/ p1, p2, p3, p4, p5, p6, p7 );

Parameters

Inputs
Register	Description
R3	p1 - Unknown
R4	p2 - Unknown
R5	p3 - Unknown
R6	p4 - Unknown
R7	p5 - Unknown
R8	p6 - Unknown
R9	p7 - Unknown
Outputs
Register	Description
R3	Status?

lv1_set_lpm_spr_trigger

Not used in current kernel.

Abstract Call

result = lv1_set_lpm_spr_trigger( /*IN*/ p1, p2 );

Parameters

Inputs
Register	Description
R3	p1 - Unknown
R4	p2 - Unknown
Outputs
Register	Description
R3	Status?

lv1_insert_htab_entry

Used in current kernel.

Kernel Call

result = lv1_insert_htab_entry( /*IN*/ p1, p2, p3, p4, p5, p6, /*OUT*/ &v1, &v2, &v3 );

Parameters

Inputs
Register	Description
R3	p1 - htab ID, 0 or returns -6
R4	p2 - hpte_group, 0 or returns -17
R5	p3 - hpte_v
R6	p4 - hpte_r
R7	p5 - Bolted flag
R8	p6 - flags?
Outputs
Register	Description
R3	Status?
R4	v1 - inserted_index
R5	v2 - evicted_v
R6	v3 - evicted_r

Notes: Kernel usage:

result = lv1_insert_htab_entry(PS3_LPAR_VAS_ID_CURRENT, hpte_group,
				       hpte_v, hpte_r,
				       HPTE_V_BOLTED, 0,
				       &inserted_index,
				       &evicted_v, &evicted_r);

lv1_read_virtual_uart

Read data from a VUART port into a provided buffer.

Kernel Call

result = lv1_read_virtual_uart( /*IN*/ port_number, buffer, bytes, /*OUT*/ bytes_read );

Parameters

Inputs
Register	Description
R3	port_number - VUART port number
R4	buffer - pointer to buffer (must be address in lpar)
R5	bytes - buffer size?
Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.
R4	bytes_read - number of bytes read into buffer

lv1_write_virtual_uart

Write a buffer of data to a VUART port.

Kernel Call

result = lv1_write_virtual_uart( /*IN*/ port_number, buffer, bytes, /*OUT*/ bytes_written );

Parameters

Inputs
Register	Description
R3	port_number - VUART port number
R4	buffer - pointer to buffer (must be address in lpar)
R5	bytes - buffer size?
Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.
R4	bytes_written - number of bytes written to VUART

lv1_set_virtual_uart_param

Set a parameter for a port on the VUART.

Kernel Call

result = lv1_set_virtual_uart_param( /*IN*/ port_number, param_id, param_value );

Parameters

Inputs
Register	Description
R3	port_number - VUART port number
R4	param_id - id of parameter to set (see notes)
R5	param_value - parameter value
Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.

See lv1_get_virtual_uart_param for parameter information.

lv1_get_virtual_uart_param

Get a parameter for a port on the VUART.

Kernel Call

result = lv1_get_virtual_uart_param( /*IN*/ port_number, param_id, /*OUT*/ &param_value );

Parameters

Inputs
Register	Description
R3	port_number - VUART port number
R4	param_id - id of parameter to set (see notes)
Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.
R4	param_value - parameter value

VUART parameters defined in vuart.c:

Parameter	param_id	Notes
PARAM_TX_TRIGGER	0
PARAM_RX_TRIGGER	1
PARAM_INTERRUPT_MASK	2
PARAM_RX_BUF_SIZE	3	read only
PARAM_RX_BYTES	4	read only
PARAM_TX_BUF_SIZE	5	read only, not referenced in current Kernel
PARAM_TX_BYTES	6	read only, not referenced in current Kernel
PARAM_INTERRUPT_STATUS	7	read only

lv1_configure_virtual_uart_irq

Configure the VUART IRQ.

Kernel Call

result = lv1_configure_virtual_uart_irq( /*IN*/ lpar_addr, /*OUT*/ &outlet );

Parameters

Inputs
Register	Description
R3	lpar_addr - logical partition address of virtual uart interrupt bitmap
Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.
R4	outlet - irq outlet

Notes:

Comment from interrupt.c:

/**
* The system supports only a single virtual uart, so multiple calls without
* freeing the interrupt will return a wrong state error.
*/

lv1_undocumented_function_167

SPE (isolation, reads from SPU_Out_Intr_Mbox and MFC_CNTL registers)

Exists on PAL 1.7. Returns -4 (LV1_DENIED_BY_POLICY) when passed 0 in R3 to R10.

lv1_undocumented_function_168

SPE (isolation, writes to MFC_CNTL register)

Exists on PAL 1.7. Returns -4 (LV1_DENIED_BY_POLICY) when passed 0 in R3 to R10.

lv1_open_device

Open the device for a given bus and device id.

Kernel Call

result = lv1_open_device( /*IN*/ bus_id, dev_id, 0 );

Parameters

Inputs
Register	Description
R3	bus_id - bus id
R4	dev_id - device id
R5	0 - Unknown
Outputs
Register	Description
R3	Status: LV1_SUCCESS (0) - OK LV1_NO_ENTRY (-6) - invalid dev_id LV1_BUSY (-9) - device already open LV1_ILLEGAL_PARAMETER_VALUE (-17) - invalid bus_id

Notes:

Valid values for bus_id and dev_id can be obtained from the repository (see lv1_get_repository_node_value).

Once open, functions such as lv1_map_device_mmio_region and lv1_allocate_device_dma_region can be used to map the device into memory.

The value of R5 does not seem to affect the outcome of the call (powers of 2 in the 64 bit range were tested). One reason for the flag could be to indicate whether to open the device in shared mode or not (and thus prevent the LV1_BUSY return code).

lv1_close_device

Close the device for a given bus and device id.

Kernel Call

result = lv1_close_device( /*IN*/ bus_id, dev_id );

Parameters

Inputs
Register	Description
R3	bus_id - bus id
R4	dev_id - device id
Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.

lv1_map_device_mmio_region

Map an MMIO region to the specified device.

Kernel Call

result = lv1_map_device_mmio_region( /*IN*/ bus_id, dev_id, bus_addr, size, page_size, /*OUT*/ &lpar_addr );

Parameters

Inputs
Register	Description
R3	bus_id - bus id
R4	dev_id - device id
R5	bus_addr - address of the region
R6	size - size of the region
R7	page_size - page size of the region
Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.
R4	lpar_addr - logical partition address of the mapped region

lv1_unmap_device_mmio_region

Unmap an MMIO region from the specified device.

Kernel Call

result = lv1_unmap_device_mmio_region( /*IN*/ bus_id, dev_id, lpar_addr );

Parameters

Inputs
Register	Description
R3	bus_id - bus id
R4	dev_id - device id
R5	lpar_addr - logical partition address of the mapped region
Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.

lv1_allocate_device_dma_region

Allocate a DMA region for the specified device.

Kernel Call

result = lv1_allocate_device_dma_region( /*IN*/ bus_id, dev_id, io_size, io_pagesize, flag, /*OUT*/ &dma_region );

Parameters

Inputs
Register	Description
R3	bus_id - bus id
R4	dev_id - device id
R5	io_size - region size
R6	io_pagesize - specified as a PAGE_SHIFT (i.e. n where pagesize = 2^n)
R7	flag - 0=32 bit mode, 2=8 bit mode
Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.
R4	dma_region - dma region address

Notes: When the device is little endian, the mode must be set to 8 bit for 8 bit DMA to work as expected, otherwise the bytes will be read/written in the wrong order. OTOH, this mode requires that 16 and 32-bit values are byte-swapped by the CPU since they will appear as little endian in memory.

lv1_free_device_dma_region

Free a previously allocated DMA region for the specified device.

Kernel Call

lv1_free_device_dma_region( /*IN*/ bus_id, dev_id, dma_region );

Parameters

Inputs
Register	Description
R3	bus_id - bus id
R4	dev_id - device id
R5	dma_region - dma region address
Outputs
Register	Description
R3	Status?

lv1_map_device_dma_region

Map a DMA region for the specified device.

Kernel Call

result = lv1_map_device_dma_region( /*IN*/ bus_id, dev_id, lpar_addr, dma_region, size, flags );

Parameters

Inputs
Register	Description
R3	bus_id - bus id
R4	dev_id - device id
R5	lpar_addr - logical partition address
R6	dma_region - dma region address
R7	size - region size
R8	flags - see notes
Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.

Notes:

In “mm.c” and “ps3_storage.c”, flags parameter is always specified as 0xf800000000000000UL. They are the same flags as the IOPTE entry ones.

lv1_unmap_device_dma_region

Unmap a DMA region for the specified device.

Kernel Call

result = lv1_unmap_device_dma_region( /*IN*/ bus_id, dev_id, dma_region, size );

Parameters

Inputs
Register	Description
R3	bus_id - bus id
R4	dev_id - device id
R5	dma_region - dma region address
R6	size - region size
Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.

lv1_read_pci_config

Read external PCI config. PS3tool only?

kboot Call

result = lv1_read_pci_config( /*IN*/ bus_id, pci_bus_id, dev_id, func_id, offset, size, /*OUT*/ &config_data );

Parameters

Inputs
Register	Description
R3	bus_id - ps3 bus id
R4	pci_bus_id - pci bus id
R5	dev_id - pci device id
R6	func_id - pci function
R7	offset - offset to store data within config_data
R8	size - size of config_data
Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.
R4	config_data - pci config data

Notes:

Code taken from kboot-10\dl\linux-2.6.16\arch\powerpc\platforms\ps3pf\pci.c (kboot-20061208)

status = lv1_read_pci_config(p->bus_id, p->bus_pci_bus, p->bus_pci_dev, p->bus_pci_func,
	(uint64_t)offset, size, &data);

lv1_write_pci_config

Write external PCI config. PS3tool only?

kboot Call

result = lv1_write_pci_config( /*IN*/ bus_id, pci_bus_id, dev_id, func_id, offset, size, config_data );

Parameters

Inputs
Register	Description
R3	bus_id - ps3 bus id
R4	pci_bus_id - pci bus id
R5	dev_id - pci device id
R6	func_id - pci function
R7	offset - offset to store data within config_data
R8	size - size of config_data
R9	config_data - pci config data
Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.

Notes:

Code taken from kboot-10\dl\linux-2.6.16\arch\powerpc\platforms\ps3pf\pci.c (kboot-20061208)

status = lv1_write_pci_config(p->bus_id, p->bus_pci_bus, p->bus_pci_dev, p->bus_pci_func,
   (uint64_t)offset, size, (uint64_t)val);
if(status) {
   /* lv1_write_pci_config can't write reg from 0x10 to 0x3f */
}

lv1_read_pci_io

Not used in current kernel.

Abstract Call

result = lv1_read_pci_io( /*IN*/ p1, p2, p3, p4, /*OUT*/ &v1 );

Parameters

Inputs
Register	Description
R3	p1 - Unknown
R4	p2 - Unknown
R5	p3 - Unknown
R6	p4 - Unknown
Outputs
Register	Description
R3	Status?
R4	v1 - Unknown

Notes:

Info taken from kboot-10\dl\linux-2.6.16\include\asm-powerpc\lv1calltab.h (kboot-20061208)

lv1_write_pci_io

Not used in current kernel.

Abstract Call

result = lv1_write_pci_io( /*IN*/ p1, p2, p3, p4, p5 );

Parameters

Inputs
Register	Description
R3	p1 - Unknown
R4	p2 - Unknown
R5	p3 - Unknown
R6	p4 - Unknown
Outputs
Register	Description
R3	Status?

Notes:

Info taken from kboot-10\dl\linux-2.6.16\include\asm-powerpc\lv1calltab.h (kboot-20061208)

lv1_undocumented_function_182

Exists in PAL 3.15. Nothing known so far. Note: probably a function that allocates or frees memory.

lv1_undocumented_function_183

Exists in PAL 3.15. Nothing known so far. Note: probably a function that allocates or frees memory.

lv1_net_add_multicast_address

Add multicast address to the specified network device.

Kernel Call

result = lv1_net_add_multicast_address( /*IN*/ bus_id, dev_id, addr, flag );

Parameters

Inputs
Register	Description
R3	bus_id - bus id
R4	dev_id - device id
R5	addr - see notes
R6	flag - see notes
Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.

Notes:

From “gelic_net.c”, addr can also take special values of 0 and GELIC_NET_BROADCAST_ADDR (0xffffffff) and flag is assigned values of 0 and 1.

lv1_net_remove_multicast_address

Remove multicast address on the specified network device.

Kernel Call

result = lv1_net_remove_multicast_address( /*IN*/ bus_id, dev_id, 0, 1 );

Parameters

Inputs
Register	Description
R3	bus_id - bus id
R4	dev_id - device id
R5	0 - Unknown
R6	1 - Unknown
Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.

lv1_net_start_tx_dma

Start DMA transmit on the specified network device.

Kernel Call

result = lv1_net_start_tx_dma( /*IN*/ bus_id, dev_id, bus_addr, 0 );

Parameters

Inputs
Register	Description
R3	bus_id - bus id
R4	dev_id - device id
R5	bus_addr - dma address?
R6	0 - Unknown
Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.

lv1_net_stop_tx_dma

Stop DMA transmit on the specified network device.

Kernel Call

result = lv1_net_stop_tx_dma( /*IN*/ bus_id, dev_id, 0 );

Parameters

Inputs
Register	Description
R3	bus_id - bus id
R4	dev_id - device id
R5	0 - Unknown
Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.

lv1_net_start_rx_dma

Start DMA receive on the specified network device.

Kernel Call

result = lv1_net_start_rx_dma( /*IN*/ bus_id, dev_id, bus_addr, 0 );

Parameters

Inputs
Register	Description
R3	bus_id - bus id
R4	dev_id - device id
R5	bus_addr - dma address?
R6	0 - Unknown
Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.

lv1_net_stop_rx_dma

Stop DMA receive on the specified network device.

Kernel Call

result = lv1_net_stop_rx_dma( /*IN*/ bus_id, dev_id, 0 );

Parameters

Inputs
Register	Description
R3	bus_id - bus id
R4	dev_id - device id
R5	0 - Unknown
Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.

lv1_net_set_interrupt_status_indicator

Set the interrupt status indicator for the specified network device.

Kernel Call

result = lv1_net_set_interrupt_status_indicator( /*IN*/ bus_id, dev_id, irq_status_addr, 0 );

Parameters

Inputs
Register	Description
R3	bus_id - bus id
R4	dev_id - device id
R5	irq_status_addr - lpar address of the irq status indicator
R6	0 - Unknown
Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.

lv1_net_set_interrupt_mask

Sets the interrupt mask for specified network device.

Kernel Call

result = lv1_net_set_interrupt_mask( /*IN*/ bus_id, dev_id, mask, 0 );

Parameters

Inputs
Register	Description
R3	bus_id - bus id
R4	dev_id - device id
R5	mask - interrupt mask
R6	0 - Unknown
Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.

lv1_net_control

Send a control command to the specified network device.

Kernel Call

result = lv1_net_control( /*IN*/ bus_id, dev_id, p1, p2, p3, p4, /*OUT*/ &v1, &v2 );

Parameters

Inputs
Register	Description
R3	bus_id - bus id
R4	dev_id - device id
R5	p1 - command dependent input parameter
R6	p2 - command dependent input parameter
R7	p3 - command dependent input parameter
R8	p4 - command dependent input parameter
Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.
R4	v1 - command dependent output parameter
R5	v2 - command dependent output parameter

lv1_undocumented_function_195

WLAN Gelic device

Exists in PAL 1.7. Returns -3 (LV1_NO_PRIVILEGE) when passed 0 in R3 to R10.

lv1_undocumented_function_196

WLAN Gelic device

Exists in PAL 1.7. Returns -3 (LV1_NO_PRIVILEGE) when passed 0 in R3 to R10.

lv1_connect_interrupt_event_receive_port

Assign a virtual interrupt to a system bus device.

Kernel Call

result = lv1_connect_interrupt_event_receive_port( /*IN*/ bus_id, dev_id, outlet, interrupt_id );

Parameters

Inputs
Register	Description
R3	bus_id - device bus id
R4	dev_id - device id
R5	outlet - interrupt outlet
R6	interrupt_id - interrupt id
Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.

lv1_disconnect_interrupt_event_receive_port

Disconnect a virtual interrupt from a system bus device.

Kernel Call

result = lv1_disconnect_interrupt_event_receive_port( /*IN*/ bus_id, dev_id, outlet, interrupt_id );

Parameters

Inputs
Register	Description
R3	bus_id - device bus id
R4	dev_id - device id
R5	outlet - interrupt outlet
R6	interrupt_id - interrupt id
Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.

lv1_get_spe_all_interrupt_statuses

Not used in current kernel.

Abstract Call

result = lv1_get_spe_all_interrupt_statuses( /*IN*/ p1, /*OUT*/ &v1 );

Parameters

Inputs
Register	Description
R3	p1 - Unknown
Outputs
Register	Description
R3	Status?
R4	v1 - Unknown

lv1_undocumented_function_200

SPE (isolation)

Exists in PAL 1.7. Returns -4 (LV1_DENIED_BY_POLICY) when passed 0 in R3 to R10.

lv1_undocumented_function_201

SPE (isolation)

Exists in PAL 1.7. Returns -4 (LV1_DENIED_BY_POLICY) when passed 0 in R3 to R10.

lv1_deconfigure_virtual_uart_irq

Deconfigure the VUART IRQ.

Kernel Call

result = lv1_deconfigure_virtual_uart_irq();

Parameters

Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.

lv1_enable_logical_spe

Enables a logical SPE.

Kernel Call

status = lv1_enable_logical_spe( /*IN*/ spe_id, resource_id );

Parameters

Inputs
Register	Description
R3	spe_id - logical spe id
R4	resource_id - spe resource id (prevously retrieved from Kernel repository)
Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.

lv1_undocumented_function_209

SPE (isolation)

Exists in PAL 1.7. Returns -4 (LV1_DENIED_BY_POLICY) when passed 0 in R3 to R10.

lv1_gpu_open

Open the GPU. Call lv1_gpu_close to close the GPU.

Kernel Call

status = lv1_gpu_open( /*IN*/ p1 );

Parameters

Inputs
Register	Description
R3	p1 - Unknown, Kernel only ever passes 0, though other randomly chosen values seem to succeed.
Outputs
Register	Description
R3	Status: 0 = LV1_SUCCESS, -6 = LV1_NO_ENTRY

Notes:

When called from Kernel module init function, if GPU is already open, subsequent calls to lv1_gpu_open return LV1_NO_ENTRY (-6). Closing the GPU and re-opening succeeds.

lv1_gpu_close

Closes the GPU. Must be called once for every call to lv1_gpu_open.

Kernel Call

status = lv1_gpu_close();

Parameters

Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.

lv1_gpu_device_map

Map a device into logical address space. Address needs to be ioremapped before use.

kboot Call

result = lv1_gpu_device_map( /*IN*/ dev_id, /*OUT*/ &lpar_addr, &lpar_size );

Parameters

Inputs
Register	Description
R3	dev_id - device id (see notes)
Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.
R4	lpar_addr - logical partition address of device block
R5	lpar_size - size of device block

Notes:

Info taken from kboot-10\dl\linux-2.6.16\sound\powerpc\snd_ps3pf.c (kboot-20061208) where the audio front-end registers are mapped into memory. Two calls to lv1_gpu_device_map are performed, the first when dev_id = 1, to obtain the audio interrupt (Audio IRQ Outlet) and a second time when dev_id = 2 to obtain a mapping of the register block (Audio Registers).

lpar_addr is a virtual address, created by the Hypervisor. Multiple calls to lv1_gpu_device_map with the same dev_id return successfully, but the lpar_address returned for each is different (if there have been no intermediary lv1_gpu_device_unmap calls). These various virtual lpar_addr values all alias the same physical location in memory.

Test Results

lv1_gpu_device_map
dev_id	result	lpar_addr	lpar_size	Comment
0	ffffffffffffffef	98d2f7d44da1ceae	0100000000000000	result = LV1_ILLEGAL_PARAMETER_VALUE
1	0000000000000000	0000300000022000	0000000000001000	Audio IRQ Outlet (map1_dump)
2	0000000000000000	00003c0000128000	0000000000008000	Audio_Registers (map2_dump)
3	0000000000000000	0000300000026000	0000000000001000	??? - Any attempt to dereference this lpar_addr locks up the PS3
4	ffffffffffffffef	0000300000026000	0000000000001000	result = LV1_ILLEGAL_PARAMETER_VALUE
5	0000000000000000	0000300000028000	0000000000001000	??? - (map5_dump)
6	0000000000000000	0000300000029000	0000000000001000	??? - (map6_dump)
7	0000000000000000	00003000002A0000	0000000000010000	??? - (map7_dump)
8	0000000000000000	000030000002B000	0000000000001000	video RAM at offset 0x0ff10000- (map8_dump)
9-255	-20	???	???	result = LV1_NOT_IMPLEMENTED

It is interesting that when dev_id = 4, LV1_ILLEGAL_PARAMETER_VALUE is returned with lpar_addr and lpar_size set to the values returned from the previous call - for the first call when dev_id = 0, values also appear to be set (though these could be garbage values)

Devices 1 & 2

dev_id 1 gives a location used to process IRQ’s from the audio and dev_id 2 gives the base address of the Audio Hardware registers. From published Sony documents (http://www.watch.impress.co.jp/game/docs/20060329/3dps303.htm), Audio is believed to be on the RSX, this call seems to confirm that. Access to the audio after this mapping call (it would appear) bypasses the Hypervisor and occurs directly on the RSX hardware. 3,5,6,7,8 are currently unknown. Presumably 0 and 4 are otherwise valid parameters blocked by the Hypervisor for OtherOS (ie, they may function for Games) otherwise I would have expected a return result of -20 for them. So rather than just being a bridge for audio into HDMI, it is for all audio.

Also interesting is that the GPU version number returned by lv1_gpu_context_allocate appears at address 0×10 in the device 1 dump, though this of course may be complete coincidence.

Device 7

dev_id 7 appears to be a video device. It is not possible to map the entire reported memory space (0×10000), only areas 0×0000 to 0x0fff and 0×2000 to 0x2fff (discovered via laborious trial and error testing, mapping other areas causes the PS3 to hang without warning). In both mappable areas, the current screen resolution can be seen at locations 0×200 and 0×210. Changes to the ps3 video mode (e.g. using the ps3videomode utility) can be observed in the mapped areas, but modifying the values directly does not affect the screen resolution. Although both areas contain different values, there appear to be parts in common, as changing the values at 0×200 and 0×210 directly in one area also causes the same values in the other area to change.

Given the screen resolution connection, it could be possible that this device is a mapping of the GPU display heads:

Out of 16Kb, only two areas are mappable (= number of accessible display heads)
Mappable areas are 2Kb apart → 8 total display heads (= size of display heads array returned by lv1_gpu_context_allocate)

Device 8

dev_id 8 appears to be a mapping of video RAM at offset 0x0ff10000. This region of video memory is referenced by RSX DMA objects but its purpose is unknown.

lv1_gpu_device_unmap

Unmaps the device from logical address space.

kboot Call

lv1_gpu_device_unmap( /*IN*/ dev_id );

Parameters

Inputs
Register	Description
R3	dev_id - device id (see lv1_gpu_device_map)
Outputs
Register	Description
R3	Status?

Notes:

Info taken from kboot-10\dl\linux-2.6.16\sound\powerpc\snd_ps3pf.c (kboot-20061208)

lv1_gpu_memory_allocate

Allocate GPU memory.

Kernel Call

status = lv1_gpu_memory_allocate(ddr_size, 0, 0, 0, 0, &memory_handle, &ddr_lpar);

Parameters

Inputs
Register	Description
R3	ddr_size - amount of DDR to reserve? (see notes)
R4	tile_max_size in bytes. Max value 512*1024.
R5	zcull_max_size in bytes. Max value 3075*1024.
R6	tile_max_areas. Max value 15.
R7	zcull_max_areas. Max value 8.
Outputs
Register	Description
R3	status: 0 = LV1_SUCCESS, -17 = LV1_ILLEGAL_PARAMETER_VALUE
R4	memory_handle - used by lv1_gpu_context_allocate and lv1_gpu_memory_free??
R5	ddr_lpar - remappable address of allocated video memory, unused by Kernel.

Notes:

ddr_size accepts values (0..252) * 2^20 - values not divisible by 2^20 (1 MB) and above the range result in a return value of -17 (LV1_ILLEGAL_PARAMETER_VALUE). [Verified by Strontium Dog on an AU PS3 V1.5 firmware]

Bits 52-63 of ddr_size seem to be ignored or correspond to flags. The lower bits correspond to the amount of allocated video RAM. A call to lv1_gpu_context_allocate using the returned memory_handle will create a RSX DMA object handle 0xfeed0000 corresponding to the region of allocated memory. Multiple calls to lv1_gpu_memory_allocate with non-zero ddr_size will change the start of this region. The DMA object limit is set to ddr_size - 1. Before FW 2.1, a ddr_size of 0 was accepted, in which case a DMA object starting at zero and of limit 0xffffffff was created. Note that in this case, the start of this region is always zero even if previous calls to lv1_gpu_memory_allocate with non-zero ddr_size were performed. As of FW 2.1 and above, a zero ddr_size is not accepted anymore.

Parameters r4-r7 are unknown. Maximum values for these parameters are respectively 512kB, 3075kB, 15 and 8. They refer to shared scarce resources, as allocations are retained across multiple calls to lv1_gpu_memory_allocate. When attached to a context during lv1_gpu_context_allocate, the values of these parameters are reported in the lpar_driver_info structure of the context.

Cell separates multiple OS into Logical Partitions (lpar) described at http://research.scea.com/research/html/CellGDC05/13.html. PS3 GPU memory is referred to as DDR (or GDDR) whereas system memory is XDR. 256 MB of each are installed in PS3 though only XDR is currently available for use by OtherOS.

To make use of the allocated DDR ddr_lpar needs to be transformed into a usable address using:

ddr_address = ioremap_flags(ddr_lpar, ddr_size, _PAGE_NO_CACHE);

Be aware that the memory that holds the physical GPU frame buffer is not allocated by the Kernel, just used. So on the first call to this, some or all of the memory you request (depending on now much you request) may be actually used as the frame buffer. You will know this, because your writes to memory will mysteriously disappear up to 20ms after you perform them. Note that direct access to video ram is very slow (~10MB/s).

Test Results

Register	Hex	Decimal	Comments
R3	0x000000000fc00000	(264241152)	252 MB
R4	0×0000000000000000	(0)
R5	0×0000000000000000	(0)
R6	0×0000000000000000	(0)
R7	0×0000000000000000	(0)
Outputs
R3	0×0000000000000000	(0)	LV1_SUCCESS
R4	0x000000005a5a5a5b	(...)	memory handle
R5	0x00007001a0000000	(...)	ddr logical partition address

lv1_gpu_memory_free

Free memory handle returned by lv1_gpu_memory_allocate. Must be called to dispose of the handle returned by lv1_gpu_memory_allocate.

Kernel Call

status = lv1_gpu_memory_free(ps3fb.memory_handle);

Parameters

Inputs
Register	Description
R3	Memory handle returned by lv1_gpu_memory_allocate
Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.

lv1_gpu_context_iomap

Map system RAM address to GPU through the Cell FlexIO interface.

Kernel Call

status = lv1_gpu_context_iomap(ps3fb.context_handle, GPU_IOIF, 
			       xdr_lpar, ps3fb_videomemory.size, 0);

Parameters

Inputs
Register	Description
R3	ps3fb.context_handle as allocated by lv1_gpu_context_allocate
R4	GPU_IOIF = 0x0d000000UL - GPU address where the system RAM virtual framebuffer is remapped
R5	xdr_lpar - lpar version of the physical address of the virtual frame buffer in local memory. (Note: the lpar version = the physical address in the PS3)
R6	ps3fb_videomemory.size = The size of the virtual frame buffer
R7	0 - IOPTE flags - bitfield describing protection, coherency and ordering of the I/O mapping. Any combination of 0 or 2^{11 (cache hint),59 (read ordering),60 (write ordering),61 (coherency),62 (read protection) ,63 (write protection)} seems valid
Outputs
Register	Description
R3	Status - 0 = OK, LV1_TYPE_MISMATCH (-8) if R5 set to a DDR lpar address, LV1_ILLEGAL_PARAMETER_VALUE (-17) if any other bit set in R7 than described above

This function creates a mapping in GPU address space so that the RSX can access system RAM. The Kernel uses it to associate the virtual framebuffer residing in system RAM to the GPU, so that so that transfers can be initiated by the RSX from the system RAM to the video RAM using the lv1_gpu_context_attribute:fb_blit() call.

Comments:

It was previously suspected that GPU_IOIF was the address of GPU MMIO registers. However GPU_IOIF is a GPU address, not a lpar address, and therefore has no meaning on the Linux side, and cannot be directly mapped from the Linux address space. Reserving the memory block (using request_mem_region) and mapping (using ioremap) results in a block of memory that is used by Linux (nothing resembling IO registers was observed whilst single frame stepping a gfx demo). [was: As you’ve previously discovered that the top of RAM is 0x0e00 0000, GPU_IOIF here is 16Mb below that. That’s typically the size of the a graphics card PCI IO region on a PC, so given the name, I’d strongly suggest it’s not GPU memory that’s being mapped but the GPU IO registers. Although why this address range would overlap with RAM is a mystery.]

GPU_IOIF was successfully set to other values (0×00000000, 0×02000000, 0×04000000) with Linux booting and displaying correctly. A value of 0x0f000000 causes the PS3 to hang (need to retest 0x0e0000000)

Although it looks like GPU_IOIF would overlap video RAM, the RSX differentiates between the two by associating different DMA objects to the source and destination of the blit. The source is associated with DMA object handle 0xfeed0001 which targets system memory, while the destination is associated with DMA object handle 0xfeed0000 which targets video memory. This has been observed by analysing the FIFO commands sent to the GPU by the hypervisor during the lv1_gpu_context_attribute:fb_setup() and lv1_gpu_context_attribute:fb_blit() calls.

It seems a call to lv1_gpu_context_iomap(handle, bus_addr, xdr_lpar, size, flags) is equivalent to a series of call to lv1_put_iopte:

int i;
int context_number; /* derived from handle, 1st allocated context 0, 2nd allocated context 1, etc... */

for (i = 0; i < size; i += 1024 * 1024) {
	lv1_put_iopte(0,             /* IO ASID */
		      ((0x08ULL + context_number) << 28) | bus_addr) + i, /* IO address */ 
		      xdr_lpar + i, /* Logical Partition address */
	              1,            /* PS3_AUDIO_IOID, actually RSX IOID */
		      flags);
}

Tested by replacing the call to lv1_gpu_context_iomap with the code above in ps3fb.c.

lv1_undocumented_function_222

Located @ 0x20D648 in 3.15 HV.

Does something with GPU Register 0x140, doesn't take arguments or return anything.

lv1_gpu_context_attribute

This is a multifunction call.

General Case

Abstract Call

status = lv1_gpu_context_attribute(ps3fb.context_handle, operation_code,

p1, p2, p3, p4 );

Parameters

Inputs
Register	Description
R3	ps3fb.context_handle as allocated by lv1_gpu_context_allocate
R4	operation_code - The code of the operation to perform.
R5	p1 - Parameter 1 to the operation
R6	p2 - Parameter 2 to the operation
R7	p3 - Parameter 3 to the operation
R8	p4 - Parameter 4 to the operation
Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.

Operations

The operation code can be one of the following:

Operation	Code	Details	Address in 3.15
No Entry	0×0000	Not a valid operation, returns LV1_NO_ENTRY (-6)
L1GPU_CONTEXT_ATTRIBUTE_FIFO_SETUP	0×0001	fifo_setup	0×210910
Unknown	0×0002	fifo_pause, (rsx_ctx, 2, 0, 0, 0, 0)	0x2108ec
Unknown	0×0003	fifo_continue, (rsx_ctx, 3, 0, 0, 0, 0)	0x2107c0
No Entry	0×0004-0x00FF	Not a valid operation, returns LV1_NO_ENTRY (-6)
L1GPU_CONTEXT_ATTRIBUTE_DISPLAY_MODE_SET	0×0100	display_mode_set	0x21092c
L1GPU_CONTEXT_ATTRIBUTE_DISPLAY_SYNC	0×0101	display_sync	0×210318
L1GPU_CONTEXT_ATTRIBUTE_DISPLAY_FLIP	0×0102	display_flip	0×210588
Unknown	0×0103	Unknown function, returns LV1_SUCCESS(0) when called with 0,0,0,0	0×210994
Unknown	0×0104	Unknown function, returns LV1_SUCCESS(0) when called with 0,0,0,0	0×210754
Unknown	0×0105	Unknown function, returns LV1_SUCCESS(0) when called with 0,0,0,0	0×210828
Unknown	0×0106	cellGcmFunc4 ? , returns LV1_SUCCESS(0) when called with 0,0,0,0	0x2109ac
Unknown	0×0107	Unknown function, returns LV1_SUCCESS(0) when called with 0,0,0,0 – Doesn’t Exist in the 3.15 HV.	N/A
Unknown	0×0108	set interrupt frequency, returns LV1_ILLEGAL_PARAMETER_VALUE(-17) when called with 0,0,0,0	0x21063c
Unknown	0×0109	Unknown function, returns LV1_SUCCESS(0) when called with 0,0,0,0	0x2104e8
Unknown	0x010A	init gcm channel, (e.g. (rsx_ctx, 0x10A, 0, 0, 0x80000000, 0))	0×210888
No Entry	0x010B-0x01FF	Not a valid operation, returns LV1_NO_ENTRY (-6)
Unknown	0×0200	Crashes the PS3 when called with 0,0,0,0. See CN2 – Doesn’t exist in 3.15	N/A
Unknown	0×0201	Unknown function, returns LV1_SUCCESS(0) when called with 0,0,0,0	0×210724
Unknown	0×0202	generate rsx graphics error ?, returns LV1_SUCCESS(0) when called with 0,0,0,0. See CN3	0x21083c
No Entry	0×0203-0x02FF	Not a valid operation, returns LV1_NO_ENTRY (-6)
Unknown	0×0300	tile, (set invalidate tile, set tile, bind tile, unbind tile)	0x2108c0
Unknown	0×0301	Zcull, (set Zcull, bind Zcull, unbind Zcull)	0x2104bc
Unknown	0×0302	Unknown function. found @ 0x2105E8 in the 3.15 HV	0x2105e8
No Entry	0×0303-0x03FF	Not a valid operation, returns LV1_NO_ENTRY (-6)
Unknown	0×0400	Unknown function, returns LV1_SUCCESS(0) when called with 0,0,0,0	0x2109d8
No Entry	0×0401-0x05FF	Not a valid operation, returns LV1_NO_ENTRY (-6)
L1GPU_CONTEXT_ATTRIBUTE_FB_SETUP	0×0600	fb_setup	0×210788
L1GPU_CONTEXT_ATTRIBUTE_FB_BLIT	0×0601	fb_blit	0x2107ec
L1GPU_CONTEXT_ATTRIBUTE_FB_BLIT_SYNC	0×0602	fb_blit_sync	0×210964
L1GPU_CONTEXT_ATTRIBUTE_FB_CLOSE	0×0603	Added on FW >= 2.1 and used in recent Linux kernel (called with 0,0,0,0) to undo fb_setup. Not a Valid operation on older firmware.	0×210694
No Entry	0×0604-0x0FFF	Not a valid operation, returns LV1_NO_ENTRY (-6)

L1GPU_CONTEXT_ATTRIBUTE_FIFO_SETUP is undocumented and has been discovered by probing.

Notes

Probing this call by passing in an unknown operation_code and parameters of 0, seems to return a status of LV1_SUCCESS (0) whereas if the operation is not a valid id, the call returns LV1_NO_ENTRY (-6)

Crash Note 1 (CN1)

Symptoms of Crash:

No Video.
Keyboard/Mouse unresponsive.
Green Power Light lit steady.
Requires hard power off to clear (holding power button on front unresponsive).

Crash Note 2 (CN2)

Symptoms of Crash:

No Video.
Keyboard/Mouse unresponsive.
Three quick beeps from internal PS3 beeper.
Power Light lit blinks red.
Pressing power Led makes it steady red, pressing again reboots.

Crash Note 3 (CN3)

Symptoms of Crash:

Video remains on display (from time preceding call).
All video updates cease.  
Linux Kernel reports repeatedly: "lv1_gpu_context_attribute FB_BLIT failed: status -32768"
Rebooted PS3 to clear using front power button, this did not fix condition.  Hard power reset required to clear.

lv1_gpu_context_attribute:display_mode_set

Sets up the display mode? In the 3.15 firmware, this function doesn’t actually do anything. It takes 3 32bit parameters but then doesn’t do anything with them. Always returns 0.

This is a specific operation of the generic operation lv1_gpu_context_attribute(...);

Kernel Call

status = lv1_gpu_context_attribute(0x0,L1GPU_CONTEXT_ATTRIBUTE_DISPLAY_MODE_SET,
				   0, 0, 1, 0);

Parameters

Inputs
Register	Description
R3	ps3fb.context_handle as allocated by lv1_gpu_context_allocate theoretically. The Kernel actually passes 0 for this operation, so it must not be required.
R4	operation_code - L1GPU_CONTEXT_ATTRIBUTE_DISPLAY_MODE_SET (0×100)
R5	p1 - 0 - Unknown.
R6	p2 - 0 - Unknown.
R7	head - 0 = Head A (Unfitted to the Retail PS3), 1 = Head B the active head on the PS3.
R8	p4 - 0 - unused.
Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.

lv1_gpu_context_attribute:display_sync

Sets up some sort of Display Sync attribute mode.

This is a specific operation of the generic operation lv1_gpu_context_attribute(...);

Kernel Call

status = lv1_gpu_context_attribute(0x0,L1GPU_CONTEXT_ATTRIBUTE_DISPLAY_SYNC,
				   head, L1GPU_DISPLAY_SYNC_VSYNC, 0, 0);

Parameters

Inputs
Register	Description
R3	ps3fb.context_handle as allocated by lv1_gpu_context_allocate theoretically. The Kernel actually passes 0 for this operation, so it must not be required.
R4	operation_code - L1GPU_CONTEXT_ATTRIBUTE_DISPLAY_SYNC (0×101)
R5	head - 0 = Head A (Unfitted to the PC), 1 = Head B the active head on the PS3.
R6	sync_type - L1GPU_DISPLAY_SYNC_VSYNC = Enable VSync? Possibly also L1GPU_DISPLAY_SYNC_HSYNC = Enable HSync?
R7	p3 - 0 - Unknown, seems unused.
R8	p4 - 0 - Unknown, seems unused.
Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.

lv1_gpu_context_attribute:display_flip

Set the start of the current video page in video memory.

This is a specific operation of the generic operation lv1_gpu_context_attribute(...);

Kernel Call

status = lv1_gpu_context_attribute(ps3fb.context_handle,
			           L1GPU_CONTEXT_ATTRIBUTE_DISPLAY_FLIP,
			           head, offset, 0, 0);

Parameters

Inputs
Register	Description
R3	ps3fb.context_handle as allocated by lv1_gpu_context_allocate theoretically.
R4	operation_code - L1GPU_CONTEXT_ATTRIBUTE_DISPLAY_FLIP (0×102)
R5	head - 0 = Head A (Unfitted to the PC), 1 = Head B the active head on the PS3.
R6	offset - Offset from start of video memory to set as active displayed memory.
R7	p3 - 0 - Unknown, seems unused.
R8	p4 - 0 - Unknown, seems unused.
Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.

lv1_gpu_context_attribute:fb_setup

Set the start of the current video page in video memory.

This is a specific operation of the generic operation lv1_gpu_context_attribute(...);

Kernel Call

status = lv1_gpu_context_attribute(ps3fb.context_handle,
		L1GPU_CONTEXT_ATTRIBUTE_FB_SETUP,
		xdr_lpar, ps3fb_videomemory.size,
		GPU_IOIF, 0);

Parameters

Inputs
Register	Description
R3	ps3fb.context_handle as allocated by lv1_gpu_context_allocate theoretically.
R4	operation_code - L1GPU_CONTEXT_ATTRIBUTE_FB_SETUP (0×600)
R5	xdr_lpar - Address of command FIFO
R6	ps3fb_videomemory.size - Size of command FIFO
R7	GPU_IOIF = 0x0d000000UL. - GPU address of command FIFO (was: I dont know what this address is. Maybe its the address of the frame buffers in Video memory???)
R8	p4 - 0 - Unknown, seems unused.
Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.

Part of patch to move FIFO from start of video memory to end:

status = lv1_gpu_context_attribute(ps3fb.context_handle,
 					   L1GPU_CONTEXT_ATTRIBUTE_FB_SETUP,
-					   xdr_lpar, ps3fb_videomemory.size,
-					   GPU_IOIF, 0);
+					   xdr_lpar + ps3fb.xdr_size,
+					   GPU_CMD_BUF_SIZE,
+					   GPU_IOIF + ps3fb.xdr_size, 0);

The memory map used to look like:

Address	Description
xdr_lpar	FIFO region
xdr_lpar + ???	not used
xdr_lpar + ps3fb_videomemory.size - 2 * frame size	frame 2
xdr_lpar + ps3fb_videomemory.size - frame size	frame 1
xdr_lpar + ps3fb_videomemory.size	END

The memory map of ps3fb now looks like this:

Address	Description
xdr_lpar	frame 1
xdr_lpar + FB_OFF(1)	frame 2
xdr_lpar + FB_OFF(2)	not used
xdr_lpar + ps3fb_videomemory.size - GPU_CMD_BUF_SIZE	FIFO region
xdr_lpar + ps3fb_videomemory.size	END

The FIFO section of the memory range is now not mapped into Linux’s address space.

So, from that change we can see that R5 and R7 are moved by the size of the xdr_size (videomemory_size-GPU_CMD_BUF_SIZE) so both refer to the FIFO buffer in different addressing schemes (probably physical memory address and LPAR address)

More discussion on this is at http://forums.ps2dev.org/viewtopic.php?t=8364

lv1_gpu_context_attribute:fb_blit

Block Image Transfer from Main memory to GPU memory.

This is a specific operation of the generic operation lv1_gpu_context_attribute(...);

Kernel Call

status = lv1_gpu_context_attribute(ps3fb.context_handle,
			           L1GPU_CONTEXT_ATTRIBUTE_FB_BLIT,
				   offset, fb_ioif,
				   L1GPU_FB_BLIT_WAIT_FOR_COMPLETION |
				   (xres << 16) | yres,
				   xres * BPP);

Parameters

Inputs
Register	Description
R3	ps3fb.context_handle as allocated by lv1_gpu_context_allocate theoretically.
R4	operation_code - L1GPU_CONTEXT_ATTRIBUTE_FB_BLIT (0×601)
R5	destination GPU address (offset in video RAM).
R6	source GPU address (GPU_IOIF + offset, for system RAM mapped by lv1_gpu_context_iomap).
R7	0×0000 : 0×0000 : xres : yres - x,y size of the blit.
R8	line_length - span, number of bytes in a line. As of Firmware 1.90, lower 32-bit is destination span, upper 32-bit if not null is source span.
Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.

lv1_gpu_context_attribute:fb_blit_sync

This call is never made by the Kernel

This is a specific operation of the generic operation lv1_gpu_context_attribute(...);

Abstract Call

status = lv1_gpu_context_attribute(ps3fb.context_handle,
			           L1GPU_CONTEXT_ATTRIBUTE_FB_BLIT_SYNC,
			           p1, p2, p3, p4);

Parameters

Inputs
Register	Description
R3	ps3fb.context_handle as allocated by lv1_gpu_context_allocate theoretically.
R4	ooperation_code - L1GPU_CONTEXT_ATTRIBUTE_FB_BLIT_SYNC (0×602)
R5	p1 - Unknown.
R6	p2 - Unknown.
R7	p3 - Unknown.
R8	p4 - Unknown.
Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.

I would expect this call to be very similar, if not identical to fb_blit.

lv1_gpu_context_intr

Tests the current IRQ state of the GPU

Kernel Call

status = lv1_gpu_context_intr(ps3fb.context_handle, &v1);

Parameters

Inputs
Register	Description
R3	ps3fb.context_handle as allocated by lv1_gpu_context_allocate.
Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.
R4	IRQ Bitmap of all pending IRQ’s. This is a bitset. A bit = 0 means IRQ not pending, 1 = IRQ pending. Bit GPU_INTR_STATUS_VSYNC_0 = 0. IRQ for vsync on head A. Unused by Kernel Bit GPU_INTR_STATUS_VSYNC_1 = 1. IRQ for vsync on head B. Used by Kernel Bit GPU_INTR_STATUS_FLIP_0 = 2. IRQ for flip on head A. Unused by Kernel Bit GPU_INTR_STATUS_FLIP_1 = 3. IRQ for flip on head B. Unused by Kernel Bit GPU_INTR_STATUS_QUEUE_0 = 4. IRQ for queue on head A. Unused by Kernel Bit GPU_INTR_STATUS_QUEUE_1 = 5. IRQ for queue on head B. Unused by Kernel

lv1_gpu_attribute

Set a GPU attribute.

kboot Call

result = lv1_gpu_attribute( /*IN*/ p1, p2, p3, p4, p5 );

Parameters

Inputs
Register	Description
R3	p1 - unknown
R4	p2 - unknown
R5	p3 - unknown
R6	p4 - unknown
R7	p5 - unknown
Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.

Notes:

Code taken from kboot-10\dl\linux-2.6.16\sound\powerpc\snd_ps3pf.c (kboot-20061208)

ret64 = lv1_gpu_attribute(0x100, 0x007, val, 0, 0);

Test Results

p1	p2	p3	p4	p5	Status
0×100	0	0	0	0
0×105	0	0	0	0	0 (LV1_SUCCESS)
0×202	0	0	0	0	0 (LV1_SUCCESS)
0×400	0	0	0	0	0 (LV1_SUCCESS)
0×401	0	0	0	0	0 (LV1_SUCCESS)
0×402	0	0	0	0	0 (LV1_SUCCESS)
0×403	0	0	0	0	0 (LV1_SUCCESS)
other values in 0-0×1000000	0	0	0	0

lv1_undocumented_function_229

Existed in PAL 1.7. Returned -17 (LV1_ILLEGAL_PARAMETER_VALUE) when passed 0 in R3 to R10.

Does not exist as of PAL 3.15.

lv1_undocumented_function_230

Exists in PAL 3.15. Unknown function; found in 3.15 HV dump.

lv1_undocumented_function_231

Exists in PAL 1.7. Returns -17 (LV1_ILLEGAL_PARAMETER_VALUE), 100000000000000h, 9000000000000000h, C000000000537EF8h, F09B89AF5001h, D0000000002B3084h in R3 to R8 when passed 0 in R3 to R10.

lv1_get_rtc

Gets the current value of the PS3’s real time clock and time base value.

Kernel Call

result = lv1_get_rtc( /*OUT*/ &rtc_val, &tb_val );

Parameters

Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.
R4	rtc_val - real time clock value
R5	tb_val - time base value

lv1_undocumented_function

Exists in PAL 3.15. Unknown function; found in 3.15 HV dump.

lv1_set_ppe_periodic_tracer_frequency

Not used in current kernel.

Abstract Call

result = lv1_set_ppe_periodic_tracer_frequency( /*IN*/ p1 );

Parameters

Inputs
Register	Description
R3	p1 - unknown
Outputs
Register	Description
R3	Status?

lv1_start_ppe_periodic_tracer

Not used in current kernel.

Abstract Call

result = lv1_start_ppe_periodic_tracer( /*IN*/ p1, p2, p3, p4, p5 );

Parameters

Inputs
Register	Description
R3	p1 - unknown
R4	p2 - unknown
R5	p3 - unknown
R6	p4 - unknown
R7	p5 - unknown
Outputs
Register	Description
R3	Status?

lv1_stop_ppe_periodic_tracer

Not used in current kernel.

Abstract Call

result = lv1_stop_ppe_periodic_tracer( /*IN*/ p1, /*OUT*/ &v1 );

Parameters

Inputs
Register	Description
R3	p1 - unknown
Outputs
Register	Description
R3	Status?
R4	v1 - Unknown

lv1_undocumented_function_243

Exists in PAL 1.7. Returns -6 (LV1_NO_ENTRY) when passed 0 in R3 to R10.

lv1_undocumented_function_244

Exists in PAL 1.7. Returns 0 (LV1_SUCCESS) when passed 0 in R3 to R10.

lv1_storage_read

Read a buffer of data from the specified device.

Kernel Call

result = lv1_storage_read( /*IN*/ dev_id, region_id, start_sector, sector_count, 0, buffer, /*OUT*/ &lv1_tag );

Parameters

Inputs
Register	Description
R3	dev_id - device id
R4	region_id - ?
R5	start_sector - start sector of read
R6	sector_count - number of sectors to read
R7	0 - ? comment says /* flags */
R8	buffer - lpar address of buffer
Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.
R4	lv1_tag - tag to identify operation?

lv1_storage_write

Write a buffer of data to the specified device.

Kernel Call

result = lv1_storage_write( /*IN*/ dev_id, region_id, start_sector, sector_count, 0, buffer, /*OUT*/ &lv1_tag );

Parameters

Inputs
Register	Description
R3	dev_id - device id
R4	region_id - ?
R5	start_sector - start sector of write
R6	sector_count - number of sectors to write
R7	0 - ? comment says /* flags */
R8	buffer - lpar address of buffer
Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.
R4	lv1_tag - tag to identify operation?

Notes: The buffer address must be nonzero – even if zero is an otherwise valid address.

lv1_undocumented_function_247

Exists in PAL 1.7. Returns -11 (LV1_WRONG_STATE) when passed 0 in R3 to R10. Does not exist as of PAL 3.15.

lv1_storage_send_device_command

Send a command to the specified device.

Kernel Call

result = lv1_storage_send_device_command( /*IN*/ dev_id, cmd_id, cmd_block, cmd_size, data_buffer, blocks, /*OUT*/ &lv1_tag );

Parameters

Inputs
Register	Description
R3	dev_id - device id
R4	cmd_id - see notes
R5	cmd_block - lpar address of command block?
R6	cmd_size - size of command block?
R7	data_buffer - lpar address of data buffer?
R8	blocks - number of data blocks?
Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.
R4	lv1_tag - tag to identify operation?

Notes:

Command ids specified in ps3_storage.h:

Command	cmd_id
LV1_STORAGE_SEND_ATAPI_COMMAND	0x01
LV1_STORAGE_ATA_HDDOUT	0x23

lv1_storage_get_async_status

Get status of asynchronous storage operations for the specified device?

Kernel Call

result = lv1_storage_get_async_status( /*IN*/ dev_id, /*OUT*/ &lv1_tag, &lv1_status );

Parameters

Inputs
Register	Description
R3	dev_id - device id
Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.
R4	lv1_tag - tag to identify operation?
R5	lv1_status - 0 = OK, else error

lv1_undocumented_function_250

Storage device

Exists in PAL 1.7. Returns -11 (LV1_WRONG_STATE) when passed 0 in R3 to R10.

lv1_undocumented_function_251

Storage device

Exists in PAL 1.7. Returns -11 (LV1_WRONG_STATE) when passed 0 in R3 to R10.

lv1_undocumented_function_252

Storage device

Exists in PAL 1.7. Returns -11 (LV1_WRONG_STATE) when passed 0 in R3 to R10.

lv1_undocumented_function_253

Storage device

Exists in PAL 1.7. Returns -11 (LV1_WRONG_STATE) when passed 0 in R3 to R10.

lv1_storage_check_async_status

Check status of an asynchronous storage operation on the specified device.

Kernel Call

result = lv1_storage_check_async_status( /*IN*/ dev_id, lv1_tag, /*OUT*/ &lv1_status );

Parameters

Inputs
Register	Description
R3	dev_id - device id
R4	lv1_tag - tag to identify operation?
Outputs
Register	Description
R3	Status - 0 = OK, Other values are unknown, but indicate failure.
R4	lv1_status - 0 = OK, else error

lv1_panic

Panic! Causes the OtherOS to be halted.

Kernel Call

lv1_panic( /*IN*/ reboot );

Parameters

Inputs
Register	Description
R3	reboot: 0 = power off, 1 = reboot after panic
Outputs
Register	Description
It is not expected that this call returns, so no Outputs.

Notes:

This hypervisor call causes the PS3 to shutdown immediately, without performing any cleanup or callbacks. Remember to sync filesystems before calling this function!

It seems that any non-zero value in R3 causes a reboot after panic, rather than just 1.

The code in the kernel does all manner of things to actually reboot, including sending vuart messages to some other process running in a different LPAR. I haven’t investigated enough to see exactly what it does, but calling lv1_panic(0) from my my code in the hypervisor causes a panic with the red light flashing until the power button is pressed whereas the kernel’s shutdown code doesn’t.

@@ Line 4,156: / Line 4,156: @@
 ===== Kernel Call =====
-  result = lv1_allocate_device_dma_region( /*IN*/ bus_id, dev_id, io_size, io_pagesize, flag, &dma_region );
+  result = lv1_allocate_device_dma_region( /*IN*/ bus_id, dev_id, io_size, io_pagesize, flag, /*OUT*/ &dma_region );
 ===== Parameters =====
@@ Line 4,196: / Line 4,196: @@
 Notes: When the device is little endian, the mode must be set to 8 bit for 8 bit DMA to work as expected, otherwise the bytes will be read/written in the wrong order. OTOH, this mode requires that 16 and 32-bit values are byte-swapped by the CPU since they will appear as little endian in memory.
 ----
 === lv1_free_device_dma_region ===

HV Syscall Reference: Difference between revisions

Revision as of 07:44, 11 October 2024

HV Syscalls

lv1_allocate_memory

Kernel Call

Parameters

lv1_write_htab_entry

Kernel Call

Parameters

lv1_construct_virtual_address_space

Kernel Call

Parameters

lv1_invalidate_htab_entries

Abstract Call

Parameters

lv1_get_virtual_address_space_id_of_ppe

Kernel Call

Parameters

lv1_query_logical_partition_address_region_info

Kernel Call

Parameters

Test Results

lv1_select_virtual_address_space

Kernel Call

Parameters

lv1_undocumented_function_8

lv1_pause

Kernel Call

Parameters

lv1_destruct_virtual_address_space

Kernel Call

Parameters

lv1_configure_irq_state_bitmap

Kernel Call

Parameters

lv1_connect_irq_plug_ext

Kernel Call

Parameters

lv1_release_memory

Kernel Call

Parameters

lv1_put_iopte

Kernel Call

Parameters

lv1_disconnect_irq_plug_ext

Kernel Call

Parameters

lv1_construct_event_receive_port

Kernel Call

Parameters

lv1_destruct_event_receive_port

Kernel Call

Parameters

lv1_send_event_locally

Kernel Call

Parameters

lv1_detect_pending_interrupts

Abstract Call

Parameters

lv1_end_of_interrupt

kboot Call

Parameters

lv1_connect_irq_plug

kboot Call

Parameters

lv1_disconnect_irq_plug

kboot Call

Parameters

lv1_end_of_interrupt_ext

Kernel Call

Parameters

lv1_did_update_interrupt_mask

Kernel Call

Parameters

lv1_shutdown_logical_partition

Abstract Call

Parameters

lv1_destruct_logical_spe

Kernel Call

Parameters