Downgrading Firmware: Difference between revisions
| Line 37: | Line 37: | ||
This saves you the effort of copying/renaming all of the .PUP's and Lv2Diag.self's that you would be using in a typical downgrade setup. | This saves you the effort of copying/renaming all of the .PUP's and Lv2Diag.self's that you would be using in a typical downgrade setup. | ||
A version without the firmware files is available [http://netload.in/datei6tNuevVor5/Automator.rar.htm here] (Last Updated: 3rd Dec) and can still be used providing you have the | A version without the firmware files is available [http://netload.in/datei6tNuevVor5/Automator.rar.htm here] (Last Updated: 3rd Dec) and can still be used providing you have the firmwares required, which is listed within the script. | ||
This script requires the following firmwares to be installed into the 'Firmware' folder and subsequently renamed: | This script requires the following firmwares to be installed into the 'Firmware' folder and subsequently renamed: | ||
Revision as of 06:07, 3 December 2012
Downgrading Firmware
This page is more like a subindex page to other pages :)
Lowest Applicable Firmware
- Look up in SKU Models Table to see what other reported
- Using fake upgrade to get lowest firmware version info
- Use get_applicable_version.pkg to receive lower/upper UDP broadcasts
HowTo/Guides & Documentation
- Downgrading with PSgrade Dongle (using Factory Service Mode)
- Remarry Bluray Drive (uses Factory Service Mode)
- QA Downgrading (QA flag extra and QA Recovery Downgrading)
- Downgrading with linux (for consoles with OtherOS or OtherOS++)
- Hardware flashing (Wiring and comparison of hardware flashers: Infectus, Progskeet 1.0 / 1.1 / Progskeet 1.2, Teensy 2.0++, PNM, PIC32MX etc)
- Flash (main reference page about flash content)
- Validating flash dumps (always validate before reflashing, 'what to check' guide page)
- Downgrading with Hardware flasher (reflashing with hardware flasher - both NAND/NOR)
- Downgrading with NAND flasher (older guides, NAND specific)
- Downgrading with NOR flasher (older guides, NOR specific)
Note: If your firmware is 3.56 or higher then there are currently no ways to downgrade using software only. You can use Hardware flashers on any firmware, including 3.56 and above.
Problems and Issues
- Downgrade BluRay Playback Issue (description of NAND consoles and Factory Service Mode issues)
Automation for Business/Lazy purposes
BwE has made an automator for setting up files needed for downgrading.
This simple script is placed on your downgrading USB and when run (in Windows) it gives you options to load Lv2Diag.self files, FSM .PUP's, Recovery Mode .PUPs as well as the copy and management of bkpps3.bin files for clients.
The script also has md5 checking and other fail-safes.
This saves you the effort of copying/renaming all of the .PUP's and Lv2Diag.self's that you would be using in a typical downgrade setup.
A version without the firmware files is available here (Last Updated: 3rd Dec) and can still be used providing you have the firmwares required, which is listed within the script.
This script requires the following firmwares to be installed into the 'Firmware' folder and subsequently renamed: Kmeaw 3.55 -> 'Kmeaw355' OFW 3.55 -> 'OFW355' Rebug 999 Downgrader -> 'Rebug999' Rogero Downgrade Automator -> 'RogeroDowngrade' Rogero 3.55 v3.7 -> 'Rogero355v3.7' Rogero 4.21 v2.0 -> 'Rogero421v2.0' Rogero 4.30 v2.03 -> 'Rogero430v2.03' The MD5 checking this script does can be slow on some USB sticks, if this is a problem simply stop using the script. It is a necessary part of the script, it determines what is in use and if it is valid. It is recommended to strictly use Rogero 355 v3.7 when downgrading firmware >3.55. Greetz to #ps3downgrade & ps3devwiki
| ||||||||||
