MX25L25635FMI-10G: Difference between revisions
Jump to navigation
Jump to search
Cfwprophet (talk | contribs) mNo edit summary |
(Fixed typo: "Noozle" -> "nozzle") |
||
| Line 63: | Line 63: | ||
=== Hint === | === Hint === | ||
On Board Dumping does not work. It should work with VCC pin lifted but i have not tested this. To Read/Write the chip you will need to desolder the Macronix Flash from the PS4 Mainboard and use a external flasher like the Teensy and [[SPIway]] or the Raspberry Pi and [[JAISPI]]. For the desoldering part you should use a Hot Air SMD Rework Station like [https://www.google.at/search?q=smd+rework+station&client=firefox-a&hs=265&rls=org.mozilla:de:official&source=lnms&tbm=isch&sa=X&ei=8721UpqTJo_csgbbs4CQAg&ved=0CAkQ_AUoAQ&biw=1920&bih=992 this one] and a [http://www.google.at/imgres?start=139&client=firefox-a&rls=org.mozilla:de:official&biw=1920&bih=992&tbm=isch&tbnid=qOeVhJr-fGra9M:&imgrefurl=http://www.ebay.de/itm/TSOL-13x10mm-A1185-Nozzle-for-850-SMD-Hot-Air-Rework-Station-Hiefs-/380645069166%3Fpt%3DUK_Home_Garden_PowerTools_SM%26hash%3Ditem58a036d16e&docid=5zwB4qulVHcYDM&itg=1&imgurl=http://pic01.uxsight.com/i/12a/ux_a12030500ux0859_ux_c.jpg&w=600&h=289&ei=3b61Up_xMYnesgb4woGAAQ&zoom=1&ved=1t:3588,r:44,s:100,i:136&iact=rc&page=4&tbnh=153&tbnw=318&ndsp=51&tx=174&ty=50 | On Board Dumping does not work. It should work with VCC pin lifted but i have not tested this. To Read/Write the chip you will need to desolder the Macronix Flash from the PS4 Mainboard and use a external flasher like the Teensy and [[SPIway]] or the Raspberry Pi and [[JAISPI]]. For the desoldering part you should use a Hot Air SMD Rework Station like [https://www.google.at/search?q=smd+rework+station&client=firefox-a&hs=265&rls=org.mozilla:de:official&source=lnms&tbm=isch&sa=X&ei=8721UpqTJo_csgbbs4CQAg&ved=0CAkQ_AUoAQ&biw=1920&bih=992 this one] and a [http://www.google.at/imgres?start=139&client=firefox-a&rls=org.mozilla:de:official&biw=1920&bih=992&tbm=isch&tbnid=qOeVhJr-fGra9M:&imgrefurl=http://www.ebay.de/itm/TSOL-13x10mm-A1185-Nozzle-for-850-SMD-Hot-Air-Rework-Station-Hiefs-/380645069166%3Fpt%3DUK_Home_Garden_PowerTools_SM%26hash%3Ditem58a036d16e&docid=5zwB4qulVHcYDM&itg=1&imgurl=http://pic01.uxsight.com/i/12a/ux_a12030500ux0859_ux_c.jpg&w=600&h=289&ei=3b61Up_xMYnesgb4woGAAQ&zoom=1&ved=1t:3588,r:44,s:100,i:136&iact=rc&page=4&tbnh=153&tbnw=318&ndsp=51&tx=174&ty=50 nozzle] to only heat up the pins of the Chip. | ||
{{Motherboard Components}} | {{Motherboard Components}} | ||
<noinclude>[[Category:Main]]</noinclude> | <noinclude>[[Category:Main]]</noinclude> | ||
Revision as of 20:18, 25 December 2013
Macronix MX25L25635FMI-10G
3V 256M-BIT [x 1/x 2/x 4] CMOS MXSMIO (SERIAL MULTI I/O) 16-SOP (300mil)
http://datasheet.octopart.com/MX25L25635FMI-10G-Macronix-datasheet-17291205.pdf
Pinout
| Pin | 1x I/O | 2x I/O | 4x I/O | Description | |
|---|---|---|---|---|---|
| S3 | 1 | DNU | DNU | SIO3 | Do not use or Serial Data Input & Output (for 4xI/O read mode) |
| 3.3 | 2 | VCC | VCC | VCC | +3V DC Power Supply |
| RS | 3 | RESET# | RESET# | RESET# | Hardware Reset Pin Active low |
| 4 | NC | NC | NC | No Connection | |
| 5 | NC | NC | NC | No Connection | |
| 6 | NC | NC | NC | No Connection | |
| CS | 7 | CS# | CS# | CS# | Chip Select |
| S1 | 8 | SO | SIO1 | SIO1 | Serial Data Output (for 1 x I/O) or Serial Data Input & Output (for 2x I/O or 4x I/O read mode) |
| S2 | 9 | WP# | WP# | SIO2 | Write Protection: connect to GND or Serial Data Input & Output (for 4x I/O read mode) |
| GND | 10 | GND | GND | GND | Ground |
| 11 | NC | NC | NC | No Connection | |
| 12 | NC | NC | NC | No Connection | |
| 13 | NC | NC | NC | No Connection | |
| 14 | NC | NC | NC | No Connection | |
| S0 | 15 | SI | SIO0 | SIO0 | Serial Data Input (for 1 x I/O) or Serial Data Input & Output (for 2x I/O or 4x I/O read mode) |
| SC | 16 | SCLK | SCLK | SCLK | Clock Input |
Hint
On Board Dumping does not work. It should work with VCC pin lifted but i have not tested this. To Read/Write the chip you will need to desolder the Macronix Flash from the PS4 Mainboard and use a external flasher like the Teensy and SPIway or the Raspberry Pi and JAISPI. For the desoldering part you should use a Hot Air SMD Rework Station like this one and a nozzle to only heat up the pins of the Chip.
| ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
