Syscon Hardware

From PS3 Developer wiki
Jump to navigation Jump to search
Syscon 1st Generation (BGA Packaging)

Syscon is the main power controller chip. It is responsible for powering up the various power systems and for configuring and initialising the CELL BE, RSX and South Bridge. It communicates with these devices via seperate SPI busses. There is external access by JTAG (disabled at factory by blowing a fuse), an EEPROM programming interface and Serial (UART). The Syscon is a SoC and consists of an ARM7TDMI (ARMv4) CPU, a 256KB EEPROM and 16KB RAM.

Serialnumbers @ SKU

Retail

Model Type Board Syscon
part no.
Soft
Id.
Notes
CECHAxx 0x01 COK-001 CXR713120-201GB 0B8E
CECHBxx 0x02 COK-001 CXR713120-201GB 0B8E
CECHCxx 0x03 COK-002 CXR713120-201GB
  or
CXR713120-202GB
0C16
CECHDxx SKU never released
CECHExx 0x04 COK-002
  or
COK-002W
CXR713120-201GB
  or
CXR713120-202GB
0C16
CECHFxx SKU never released
CECHGxx 0x05 SEM-001 CXR713120-201GB
  or
CXR713120-202GB
  or
CXR713120-203GB
0D52
CECHHxx 0x06 DIA-001 CXR714120-301GB 0DBF
CECHIxx SKU never released
CECHJxx 0x07 DIA-002 CXR714120-301GB
  or
CXR714120-302GB
0E69
CECHKxx 0x07 DIA-002 CXR714120-301GB
  or
CXR714120-302GB
0E69
CECHLxx 0x08 VER-001 SW-301
  or
SW-302
065D
CECHMxx 0x08 VER-001 SW-301
  or
SW-302
065D
CECHNxx SKU never released
CECHOxx SKU never released
CECHPxx 0x08 VER-001 SW-301
  or
SW-302
065D
CECHQxx 0x08 VER-001 SW-301
  or
SW-302
065D
CECH-20xx 0x09 DYN-001 SW2-301 0832
CECH-21xx 0x0A SUR-001 SW2-301
  or
SW2-302
08A0
CECH-25xx 0x0B JTP-001
  or
JSD-001
SW2-301  or
SW2-302  or
SW2-303
08C2
CECH-30xx 0x0C KTE-001 SW2-301  or
SW2-302  or
SW2-303
0918
CECH-40xx 0x0D MSX-001
  or
MPX-001
SW3-302 098F


Prototypes

Model Type Board Syscon
part no.
Soft
Id.
Active JTAG Notes
CEB-3040 - MTU-501 CXR713F120GB-000
DECR1000(A/J) 0x01 TMU-520 CXR713F120A 03FB ?
DEH-H1000A(S)(-E(S)) 0x01 COK-001 (Prototype) CXR713F120A 0B67 ?
DEH-H1001-D 0x01 COOKIE-13 CXR713F120A ?0B67? ?



Not mentioned:

0F29 - ?
0F38 - ?

Syscon Externalised Ports

Note: for more specific information per model, see the links to each subppage in the Serialnumbers @ SKU table.

Syscon UART

BGA Name Description
P16 UART0_TxD Serial Transmit
P15 UART0_RxD Serial Receive

You can attach a 3.3v TTL cable (LV-TTL) to the UART on syscon (UART0_TxD, UART0_RxD). Baud rate is 57600. There is a simple plaintext protocol involved. This varies on different syscon models. Example:

<command>:<hash>

Where the hash is the sum of command bytes & 0xFF

you should terminate commands with \r\n, the syscon messages are only terminated with \n

Here are some of the commands/messages encountered:

Messages:
Power applied (standby mode)
OK 00000000:3A

Power on
# (PowerOn State):7F

Power off (Hard shutdown)
# (PowerOff State):DD

After Fan test:
# (PowerOff State) (Fatal):36

No text, invalid hash:
NG F0000002:4D

Commands:
VER:ED
OK 00000000 S1E 00 00 065D:A4

ERRLOG:CB
OK 00000000:3A

DATE:1E
NG F0000003:4E

Syscon (SPI) EEPROM

BGA Name Description
F16 CSB Chip Select (needs always 3.3V )
H16 DO Serial Data Output
G16 DI Serial Data Input
E16 SKB Serial Data Clock
U15 WCB Write Protect
U16 RBB Read/Busy

Syscon JTAG

disabled in factory after production on retailmodels

BGA Name Description
L8 JRTCK Return Test Clock
K8 JTCK Test Clock
K9 JTDO Test Data Out
L9 JTMS Test Mode State / Test Mode Select
K7 JTDI Test Data In
L7 JNTRST Test Reset

Syscon Underlaying ports

Syscon Cell SPI Bus

BGA Name Description
M2 /BE_SPI_CS Chip Select
N2 BE_SPI_DO Serial Data Output
M1 BE_SPI_DI Serial Data Input
N1 BE_SPI_CLK Serial Data Clock
P2 /BE_RESET CellBE Reset
P1 BE_POWGOOD CellBE PowerGood
T2 /BE_INT CellBE Interrupt

Syscon Southbridge SPI Bus

BGA Name Description
B9 /SB_SPI_CS Chip Select
B8 SB_SPI_DO Serial Data Output
A9 SB_SPI_DI Serial Data Input
A8 SB_SPI_CLK Serial Data Clock


Template:Models