Template:Syscon pinout BGA 200 pads: Difference between revisions
Jump to navigation
Jump to search
(All table "rowspan" removed) |
(Table rows reordered by "Pad" column) |
||
| Line 11: | Line 11: | ||
! Pad !! Port !! Name !! Type !! Description | ! Pad !! Port !! Name !! Type !! Description | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="A01" | A1 || NC || NC || ? || Not connected | ||
|- | |||
| data-sort-value="A02" | A2 || J || DISC_IN || ? || Connected to BluRay Drive connector (CN3221) pin 52 | |||
|- | |||
| data-sort-value="A03" | A3 || J || SW_0 || ? || Connected to [[Regulators#Fujitsu_MB39A116PFT_.282_channel_DC.2FDC_converter.29 | Fujitsu MB39A116PFT]] (IC6003) pin 9 (switches +5V_MISC)<br>Connected to [[Regulators#Fujitsu_MB39A116PFT_.282_channel_DC.2FDC_converter.29 | Fujitsu MB39A116PFT]] (IC6003) pin 10 (switches +3.3V_MISC)<br>Connected to [[Components#Texas_Instruments_SN105233DBTR|Texas Instruments SN105233DBTR]] (IC6301) pin 10 (switches +1.7_MISC) | |||
|- | |||
| data-sort-value="A04" | A4 || J || SW_8_C || ? || Connected to [[Components#Texas_Instruments_SN105233DBTR|Texas Instruments SN105233DBTR]] (IC6301) pin 9 (switches +1.8V_RSX_FBVDDQ)<br>Connected to [[Regulators#OnSemi_NCP511SN18T1_.281.8V_150_mA_CMOS_Low_Iq_Low-Dropout_Voltage_Regulator.29 | OnSemi NCP511SN18T1]] (IC6008) pin 3 (switches +1.8V_RSX_PLL_VDD) | |||
|- | |||
| data-sort-value="A05" | A5 || J || DISC_OUT12_SW || ? || Connected to BluRay Drive connector (CN3221) pin 58 | |||
|- | |- | ||
| data-sort-value=" | | data-sort-value="A06" | A6 || R || MC_RESERVED2 || ? || Not connected to BluRay Drive because a missing resistor (R4080). BD_LED | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="A07" | A7 || R || MC_ALIVE || ? || Connected to BluRay Drive connector (CN3221) pin 47 | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="A08" | A8 || K || SB_SPI_CLK || ? || Southbridge SPI Bus | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="A09" | A9 || K || SB_SPI_DI || ? || Southbridge SPI Bus | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="A10" | A10 || K || DVE_I2C_SCL || ? || Connected to Digital Video Encoder [[CXM4024R]] pin 35 | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="A11" | A11 || K || ACDC_STBY || ? || Connected to [[Power Supply]] (small connector). This signal enables +12V_MAIN power rail (big prongs) | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="A12" | A12 || E || EJECT_SW || ? || Connected to [[Switch_boards|Switch board]] [[CSW-001]] connector pin 5 | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="A13" | A13 || E || SB_EBUS_RESET || ? || SS2_RESET (StarShip2 related), not connected because a missing resistor (R4135) ? | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="A14" | A14 || E || PE3 || ? || | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="A15" | A15 || E || BE_POW_FAIL || ? || Connected to [[Regulators#OnSemi_NCP5318FTR2G_.28Two.2FThree.2FFour-Phase_Buck_CPU_Controller.29|OnSemi NCP5318FTR2G]] (IC6103) pin 7 | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="A16" | A16 || NC || NC || ? || Not connected | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="B01" | B1 || <abbr title="Power port>PWR</abbr> || AVREF1 || ? || +3.3V_EVER | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="B02" | B2 || J || DISC_OUT8_SW || ? || Connected to BluRay Drive connector (CN3221) pin 57 | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="B03" | B3 || J || PJ3 || ? || Not connected in retail PS3 models (testpad CL4089) | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="B04" | B4 || J || SW_8_B || ? || Connected to [[Regulators#Mitsumi_MM1561JFBE_.28Low-Saturation_500mA_Regulators.29|Mitsumi MM1561JFBE]] (IC2408) pin 5 (switches +1.8V_ANA)<br>Connected to [[Regulators#Mitsumi_MM1593DFBEG_.28Low-Saturation_300mA_Regulators.29|Mitsumi MM1593DFBEG]] (IC2407) pin 5 (switches +3.3V_ANA)<br>Connected to transistor DTC144EUA-T106 (Q2401) base pin (switches +5V_ANA ?)<br>Connected to [[Regulators#OnSemi_NCP511SN15T1G_.281.5_V_150_mA_CMOS_Low_Iq_Low_Dropout_Voltage_Regulator_-_TSOP-5.29|OnSemi NCP511SN15T1G]] (IC6019) pin 3 (switches +1.5V_AVCG_VDDIO)<br>Connected to [[Regulators#Rohm_BD3521FVM-TR_.28Single_channel_Regulator_Driver_IC.29|Rohm BD3521FVM-TR]] (IC6017) pin 3 (switches +1.5V_RSX_VDDIO) | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="B05" | B5 || J || DVE_RST || ? || Connected to Digital Video Encoder [[CXM4024R]] pin 31 ? | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="B06" | B6 || R || MC_P_OFF_REQ || ? || Connected to BluRay Drive connector (CN3221) pin 48 | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="B07" | B7 || R || MC_RESERVED1 || ? || Connected to BluRay Drive connector (CN3221) pin 49 | ||
|- | |- | ||
| data-sort-value="B08" | B8 || K || SB_SPI_DO || ? || Southbridge SPI Bus | | data-sort-value="B08" | B8 || K || SB_SPI_DO || ? || Southbridge SPI Bus | ||
|- | |- | ||
| data-sort-value="B09" | B9 || K || SB_SPI_CS || ? || Southbridge SPI Bus | | data-sort-value="B09" | B9 || K || SB_SPI_CS || ? || Southbridge SPI Bus | ||
|- | |- | ||
| data-sort-value="B10" | B10 || K || DVE_I2C_SDA || ? || Connected to Digital Video Encoder [[CXM4024R]] pin 36 | | data-sort-value="B10" | B10 || K || DVE_I2C_SDA || ? || Connected to Digital Video Encoder [[CXM4024R]] pin 36 | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="B11" | B11 || K || PK0 || ? || | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="B12" | B12 || E || POW_SW || ? || Connected to [[Switch_boards|Switch board]] [[CSW-001]] connector pin 4 | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="B13" | B13 || E || SB_EBUS_BRDY || ? || SS2_BRDY (StarShip2 related) | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="B14" | B14 || E || VD_CECI1 || ? || | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="B15" | B15 || E || POW_FAIL || ? || Connected to [[Components#Mitsumi_PST3642UL_.28IC_for_CMOS_System_Reset.29|Mitsumi PST3642UL]] (IC6023) pin 4. Used to monitor the state of +12V_MAIN power rail | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="B16" | B16 || <abbr title="Reset & Clock">RST</abbr> || OSCOUT || ? || Connected to crystal 32.768Khz | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="C01" | C1 || O || MK_I2C_SDA || ? || Connected to [[Timebases#ICS_ICS1493G-18LFT|ICS1493G-18LFT]] clock generator (IC5001) pin 47 | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="C02" | C2 || <abbr title="Power port>PWR</abbr> || AVREF2 || ? || Ground | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="C15" | C15 || <abbr title="Power port>PWR</abbr> || VSSep || ? || EEPROM Ground | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="C16" | C16 || <abbr title="Reset & Clock">RST</abbr> || OSCIN || ? || Connected to crystal 32.768Khz | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="D01" | D1 || O || MK_I2C_SCL || ? || Connected to [[Timebases#ICS_ICS1493G-18LFT|ICS1493G-18LFT]] clock generator (IC5001) pin 46 | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="D02" | D2 || <abbr title="Power port>PWR</abbr> || VDD2 || ? || +1.5V_RSX_VDDIO | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="D04" | D4 || O || XDR_FET_RST || ? || XDR_RQ_RST | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="D05" | D5 || O || XCG_EN || ? || Connected to [[Timebases#ICS_ICS9218AGLFT_.28IC_CLOCK_GEN_RAMBUS_XDR_28-TSSOP.29|ICS9218AGLFT]] (IC5002) pin 11 (switches BE_Y0_RQ_CTM/N, BE_Y1_RQ_CTM/N)<br>Connected to [[Timebases#ICS_ICS9218AGLFT_.28IC_CLOCK_GEN_RAMBUS_XDR_28-TSSOP.29|ICS9218AGLFT]] (IC5003) pin 11 (switches BE_PLL_REFCLK_P/N)<br>Connected to [[Timebases#ICS_ICS9214DGLFT_.28IC_CLOCK_GEN_RAMBUS_XDR_28-TSSOP.29|ICS9214DGLFT]] (IC5004) pin 11 (switches BE_RC_REFCLK_P/N, RSX_RC_REFCLK_P/N, SB_RC_REFCLK_P/N) | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="D06" | D6 || H || VD_CECI0 || ? || | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="D07" | D7 || H || RSX_POW_FAIL<!--RS_POW_FAIL is an official typo, the name appears several times but only one of them have the typo--> || ? || Connected to [[Regulators#OnSemi_NCP5318FTR2G_.28Two.2FThree.2FFour-Phase_Buck_CPU_Controller.29|OnSemi NCP5318FTR2G]] (IC6201) pin 7 | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="D08" | D8 || H || MUL_TRG_IN || ? || Connected to missing components (IC4003, IC4004, IC4005) pin 3 and 6 (related with BE_TRG_IN/OUT, RSX_TRG_IN/OUT, SB_TRG_IN/OUT) | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="D09" | D9 || H || SB_INT || ? || | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="D10" | D10 || F || MUL_TRG_OUT || ? || Connected to missing components (IC4006) pin 2 (related with BE_TRG_IN/OUT, RSX_TRG_IN/OUT, SB_TRG_IN/OUT) | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="D11" | D11 || F || SB_RESET || ? || Connected to [[88SA8040-TBC1]] SATA2PATA BluRay controller pin 17<br>Connected to GL852 (IC3305) USB HUB pin 38<br>Connected to Multi-card-board connector CN3219 pin 7 | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="D12" | D12 || F || PF2<br>BE_VCS_1.25_ON || ? || [[COK-001]]/[[COK-002]] PF2 (Not connected)<br>[[SEM-001]] BE_VCS_1.25_ON | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="D13" | D13 || F || SW_1_A || ? || Connected to [[Regulators#Mitsumi_MM1593DFBEG_.28Low-Saturation_300mA_Regulators.29|Mitsumi MM1593DFBEG]] (IC6020) pin 5 (switches +3.3V_MK_VDD) for Clock Synthesizer | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="D15" | D15 || <abbr title="Reset & Clock">RST</abbr> || 32KIN || ? || Connected to resistor 22ohm to pad D16 | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="D16" | D16 || <abbr title="Reset & Clock">RST</abbr> || 32KOUT || ? || Connected to resistor 1K to +3.3V_EVER | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="E01" | E1 || <abbr title="Power port>PWR</abbr> || VSS || ? || Ground | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="E02" | E2 || N || RSX_SPI_CS || ? || RSX SPI Bus | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="E04" | E4 || O || EJECT_MECHA || ? || Connected to BluRay Drive connector (CN3221) pin 56 | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="E05" | E5 || O || PO0 || ? || Not connected (testpad CL4086) | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="E06" | E6 || H || HDMI_INT || ? || Connected to [[TC7WP3125FK]] (IC2501) pin 6. This is a syscon input at 3.3V<br> The [[TC7WP3125FK]] converts the signal originally triggered by [[Sil9132CBU]] pad E10 ? at 1.5V and converts it to 3.3V for syscon<br>The [[TC7WP3125FK]] also converts the signal RS_SPDO0 (at 1.5V) into RS_SPDO0_33 (at 3.3V) | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="E07" | E7 || H || MECHA_INT || ? || Not connected in retail PS3 models (testpad CL4102). The related SouthBridge pad is tied to GND with a 10k resistor (R3163) | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="E08" | E8 || H || MUL_CHKSTP_IN || ? || SB_CHKSTP_OUT | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="E09" | E9 || H || SYS_THR_ALRT || ? || Connected to CELL 90nm pad AP23 | ||
|- | |- | ||
| data-sort-value="E10" | E10 || F || MUL_CHKSTP_OUT || ? || | | data-sort-value="E10" | E10 || F || MUL_CHKSTP_OUT || ? || | ||
|- | |- | ||
| data-sort-value="E11" | E11 || F || SB_CGRESET || ? || SB_CGRST (the name indicates that it resets the clock generator for the southbridge) | | data-sort-value="E11" | E11 || F || SB_CGRESET || ? || SB_CGRST (the name indicates that it resets the clock generator for the southbridge) | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="E12" | E12 || F || BT_WAKEON || ? || Connected to wifi board connector (CN3701) pin 30 (named BT_WAKE). This is a syscon input | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="E13" | E13 || F || PF1<br>BE_VCS_1.30_ON || ? || [[COK-001]]/[[COK-002]] PF1 (Not connected)<br>[[SEM-001]] BE_VCS_1.30_ON | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="E15" | E15 || <abbr title="EEPROM Interface">EEP</abbr> || PP3 || ? || | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="E16" | E16 || <abbr title="EEPROM Interface">EEP</abbr> || SKB || ? || | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="F01" | F1 || N || RSX_SPI_DI || ? || RSX SPI Bus | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="F02" | F2 || N || RSX_SPI_DO || ? || RSX SPI Bus | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="F04" | F4 || O || HDMI_RST0 || ? || Connected to [[Sil9132CBU|HDMI controller Sil9132CBU]] pad G2 ? | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="F05" | F5 || O || DISC_IN_MECHA || ? || Connected to BluRay Drive connector (CN3221) pin 55 | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="F06" | F6 || <abbr title="Power port>PWR</abbr> || VDD3 || ? || +3.3V_EVER | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="F07" | F7 || <abbr title="Power port>PWR</abbr> || AVDD || ? || +3.3V_EVER | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="F08" | F8 || <abbr title="Power port>PWR</abbr> || VDD3 || ? || +3.3V_EVER | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="F09" | F9 || NC || NC || ? || Not connected | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="F10" | F10 || <abbr title="Power port>PWR</abbr> || VDD3 || ? || +3.3V_EVER | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="F11" | F11 || <abbr title="Power port>PWR</abbr> || VDDbat || ? || +battery | ||
|- | |- | ||
| data-sort-value="F12" | F12 || D || MK_EN || ? || Connected to [[Timebases#ICS_ICS1493G-18LFT|ICS1493G-18LFT]] clock generator (IC5001) pin 16 | | data-sort-value="F12" | F12 || D || MK_EN || ? || Connected to [[Timebases#ICS_ICS1493G-18LFT|ICS1493G-18LFT]] clock generator (IC5001) pin 16 | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="F13" | F13 || D || SW_5_B || ? || Connected to [[Regulators#Rohm_BD3520FVM-TR_.28Single_channel_Regulator_Driver_IC.29|Rohm BD3520FVM-TR]] (IC6200) pin 3 (switches +1.2V_RSX_VDDR) | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="F15" | F15 || <abbr title="EEPROM Interface">EEP</abbr> || PP0 || ? || | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="F16" | F16 || <abbr title="EEPROM Interface">EEP</abbr> || CSB || ? || | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="G01" | G1 || N || RSX_SPI_CLK || ? || RSX SPI Bus | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="G02" | G2 || N || RSX_RESET || ? || | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="G04" | G4 || O || HDMI_RST1 || ? || Not connected ? (it seems to be a secondary reset signal for [[Sil9132CBU|HDMI controller Sil9132CBU]] never used in retail PS3 models) | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="G05" | G5 || O || SW_AVCG<br>PO5 || ? || Connected to [[Timebases#ICS_ICS422AG-07LFT_.28IC_CLOCK_GEN_RSX_AV_CLK_24-TSSOP.29|ICS422AG-07LFT]] (IC2102) pin 12 (switches RSX_AVCLK0, RSX_AVCLK1, RSX_AVCLK2, RSX_AVCLK3) clocks for [[RSX]] and indirectly for EEGS<->RDRAM | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="G06" | G6 || <abbr title="Power port>PWR</abbr> || AVSS || ? || Ground | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="G06" | G7 || <abbr title="Power port>PWR</abbr> || VSS || ? || Ground | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="G08" | G8 || <abbr title="Power port>PWR</abbr> || VSS || ? || Ground | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="G09" | G9 || NC || NC || ? || Not connected | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="G10" | G10 || <abbr title="Power port>PWR</abbr> || VSS || ? || Ground | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="G11" | G11 || <abbr title="Power port>PWR</abbr> || VDDep || ? || EEPROM Power (+3.3V_EVER) | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="G12" | G12 || D || BEVRM_VID4 || ? || Connected to [[Regulators#OnSemi_NCP5318FTR2G_.28Two.2FThree.2FFour-Phase_Buck_CPU_Controller.29|OnSemi NCP5318FTR2G]] (IC6103) pin 3 | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="G13" | G13 || D || BEVRM_VID5 || ? || Connected to [[Regulators#OnSemi_NCP5318FTR2G_.28Two.2FThree.2FFour-Phase_Buck_CPU_Controller.29|OnSemi NCP5318FTR2G]] (IC6103) pin 30 | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="G15" | G15 || <abbr title="EEPROM Interface">EEP</abbr> || PP2 || ? || | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="G16" | G16 || <abbr title="EEPROM Interface">EEP</abbr> || DI || ? || | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="H01" | H1 || N || PN5 || ? || | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="H02" | H2 || N || PN6 || ? || | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="H04" | H4 || L || PL2 || ? || Not Connected | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="H05" | H5 || L || PL1 || ? || Not Connected | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="H06" | H6 || L || PL0 || ? || Not Connected | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="H07" | H7 || <abbr title="Power port>PWR</abbr> || DVDD || ? || +1.8V_EVER | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="H10" | H10 || <abbr title="Power port>PWR</abbr> || VDD3 || ? || +3.3V_EVER | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="H11" | H11 || <abbr title="Reset & Clock">RST</abbr> || TESTMODE || ? || | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="H12" | H12 || D || BEVRM_VID2 || ? || Connected to [[Regulators#OnSemi_NCP5318FTR2G_.28Two.2FThree.2FFour-Phase_Buck_CPU_Controller.29|OnSemi NCP5318FTR2G]] (IC6103) pin 1 | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="H13" | H13 || D || BEVRM_VID3 || ? || Connected to [[Regulators#OnSemi_NCP5318FTR2G_.28Two.2FThree.2FFour-Phase_Buck_CPU_Controller.29|OnSemi NCP5318FTR2G]] (IC6103) pin 2 | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="H15" | H15 || <abbr title="EEPROM Interface">EEP</abbr> || PP1 || ? || | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="H16" | H16 || <abbr title="EEPROM Interface">EEP</abbr> || DO || ? || | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="J01" | J1 || N || RSX_FLDO1 || ? || | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="J02" | J2 || N || RSX_INT || ? || | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="J04" | J4 || L || PL4 || ? || Not Connected | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="J05" | J5 || L || PL3 || ? || Not Connected | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="J06" | J6 || <abbr title="Power port>PWR</abbr> || VDD3 || ? || +3.3V_EVER | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="J07" | J7 || <abbr title="Power port>PWR</abbr> || DVDD || ? || +1.8V_EVER | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="J10" | J10 || <abbr title="Power port>PWR</abbr> || DVDD || ? || +1.8V_EVER | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="J11" | J11 || <abbr title="Reset & Clock">RST</abbr> || RST || ? || Connected to [[Service_Connectors#CN4009| service connector]] (CN4009) pin 8 | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="J12" | J12 || D || BEVRM_VID0 || ? || Connected to [[Regulators#OnSemi_NCP5318FTR2G_.28Two.2FThree.2FFour-Phase_Buck_CPU_Controller.29|OnSemi NCP5318FTR2G]] (IC6103) pin 31 | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="J13" | J13 || D || BEVRM_VID1 || ? || Connected to [[Regulators#OnSemi_NCP5318FTR2G_.28Two.2FThree.2FFour-Phase_Buck_CPU_Controller.29|OnSemi NCP5318FTR2G]] (IC6103) pin 32 | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="J15" | J15 || <abbr title="EEPROM Interface">EEP</abbr> || WCB || ? || | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="J16" | J16 || <abbr title="EEPROM Interface">EEP</abbr> || RBB || ? || | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="K01" | K1 || N || VD_VINT0 || ? || | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="K02" | K2 || N || VD_VINT1 || ? || | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="K04" | K4 || L || PL6 || ? || Not Connected | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="K05" | K5 || L || PL5 || ? || Not Connected | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="K06" | K6 || <abbr title="Power port>PWR</abbr> || VSSF || ? || Ground | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="K07" | K7 || JTAG || JTDI || ? || Connected to [[Service_Connectors#CN4009| service connector]] (CN4009) pin 3 | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="K08" | K8 || JTAG || JTCK || ? || Connected to [[Service_Connectors#CN4009| service connector]] (CN4009) pin 5 | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="K09" | K9 || JTAG || JTDO || ? || Connected to [[Service_Connectors#CN4009| service connector]] (CN4009) pin 6 | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="K10" | K10 || <abbr title="Power port>PWR</abbr> || DVDD || ? || +1.8V_EVER | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="K11" | K11 || <abbr title="Power port>PWR</abbr> || VSSF || ? || Ground | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="K12" | K12 || C || I2CBUS_EN || ? || Connected to [[Components#Toshiba_TC7WB66FK.28TE85R.29_.28low_on-resistance.2C_high-speed_CMOS2-bit_bus_switch.29|Toshiba TC7WB66FK]] pins 3 and 7 (IC5005 on [[SEM-001]]) through 1K resistor (in COK-001 the resistor is missing, a.k.a. this syscon line is N/C). This chip "duplicates" the MK_I2C_SCL/MK_I2C_SDA bus into a secondary XCG_I2C_SCL/XCG_I2C_SDA bus for the clock reference chip/s | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="K13" | K13 || C || PC7 || ? || Not connected in retail PS3 models (testpad CL4085) | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="K15" | K15 || <abbr title="EEPROM Interface">EEP</abbr> || PI6 || ? || | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="K16" | K16 || <abbr title="EEPROM Interface">EEP</abbr> || PI7 || ? || | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="L01" | L1 || <abbr title="Power port>PWR</abbr> || VSS || ? || Ground | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="L02" | L2 || <abbr title="Power port>PWR</abbr> || VDD0 || ? || +1.2V_MC2_VDDIO | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="L04" | L4 || L<!--the name "Port N" is an official typo--> || PL8 || ? || Not Connected | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="L05" | L5 || L || PL7 || ? || Not Connected | ||
|- | |- | ||
| data-sort-value="L06" | L6 || <abbr title="Power port>PWR</abbr> || VDDF || ? || +3.3V_EVER | | data-sort-value="L06" | L6 || <abbr title="Power port>PWR</abbr> || VDDF || ? || +3.3V_EVER | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="L07" | L7 || JTAG || JNTRST || ? || Connected to [[Service_Connectors#CN4009| service connector]] (CN4009) pin 2 ? | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="L08" | L8 || JTAG || JRTCK || ? || Connected to [[Service_Connectors#CN4009| service connector]] (CN4009) pin 4 | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="L09" | L9 || JTAG || JTMS || ? || Connected to [[Service_Connectors#CN4009| service connector]] (CN4009) pin 7 | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="L10" | L10 || <abbr title="Power port>PWR</abbr> || DVDD || ? || +1.8V_EVER | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="L11" | L11 || <abbr title="Power port>PWR</abbr> || DVDD || ? || +1.8V_EVER | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="L12" | L12 || C || RSXVRM_VID4 || ? || Connected to [[Regulators#OnSemi_NCP5318FTR2G_.28Two.2FThree.2FFour-Phase_Buck_CPU_Controller.29|OnSemi NCP5318FTR2G]] (IC6201) pin 3 | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="L13" | L13 || C || RSXVRM_VID5 || ? || Connected to [[Regulators#OnSemi_NCP5318FTR2G_.28Two.2FThree.2FFour-Phase_Buck_CPU_Controller.29|OnSemi NCP5318FTR2G]] (IC6201) pin 30 | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="L15" | L15 || I || DISC_CHUCK || ? || Connected to BluRay Drive connector (CN3221) pin 54 | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="L16" | L16 || I || SW_PCI || ? || Connected to [[Regulators#Mitsumi_MM1591FFBEG_.28Low-Saturation_300mA_Regulators.29 | Mitsumi MM1591FFBEG]] (IC6021) pin 5 (switches +1.5V_BRIDGE) for the PS2 bridge [[CXD9208GP]]<br>Connected to [[Regulators#Mitsumi_MM1593DFBEG_.28Low-Saturation_300mA_Regulators.29 | Mitsumi MM1593DFBEG]] (IC6022) pin 5 (switches +3.3V_BRIDGE) for the PS2 bridge [[CXD9208GP]]<br>Connected to PCI service connector pin 80 | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="M01" | M1 || M || BE_SPI_DI || ? || Connected to CELL 90nm pad AR13 (SPI Bus) | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="M02" | M2 || M || BE_SPI_CS || ? || Connected to CELL 90nm pad AP13 (SPI Bus) | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="M04" | M4 || A || PA0 || ? || Not connected in retail PS3 models (testpad CL4092) | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="M05" | M5 || A || WLAN_RESET || ? || Connected to wifi board connector (CN3701) pin 29 (named 11G_RESET). This is a syscon output | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="M06" | M6 || A || PA4 || ? || Not connected in retail PS3 models (testpad CL4087) | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="M07" | M7 || A || POW_LED || ? || Connected to [[Switch_boards|Switch board]] [[CSW-001]] connector pin 6 | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="M08" | M8 || G || FANPWM1 || ? || Secondary fan output (non-retail PS3 models only) | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="M09" | M9 || G || BUZZER || ? || | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="M10" | M10 || G || XDR_FET_VREF || ? || Connected to transistor DTC144EUA-T106 (Q4008). Switches XDR_RQ_VREF_FET | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="M11" | M11 || G || SW_ATA || ? || Connected to UMH2NTN dual transistor (Q6009) pin 2 (switches +12V_BD)<br>Connected to UMH2NTN dual transistor (Q6009) pin 5 (switches +5V_BD)<br>Connected to UMH2NTN dual transistor (Q6006) pin 2 (switches +5V_HDD) | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="M12" | M12 || C || RSXVRM_VID2 || ? || Connected to [[Regulators#OnSemi_NCP5318FTR2G_.28Two.2FThree.2FFour-Phase_Buck_CPU_Controller.29|OnSemi NCP5318FTR2G]] (IC6201) pin 1 | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="M13" | M13 || C || RSXVRM_VID3 || ? || Connected to [[Regulators#OnSemi_NCP5318FTR2G_.28Two.2FThree.2FFour-Phase_Buck_CPU_Controller.29|OnSemi NCP5318FTR2G]] (IC6201) pin 2 | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="M15" | M15 || I || SW_2 || ? || Connected to [[Regulators#Texas_Instruments_TPS51117PWRG4_.281.8V_to_28V_Input_Sync._Step_Down_Controller_10A_0.75_V_to_5.5_V.29|Texas Instruments TPS51117PWRG4]] (IC6302) pin 1 (switches +1.8V_VDD_MEM) | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="M16" | M16 || I || DISC_PHOT_LED || ? || Connected to BluRay Drive connector (CN3221) pin 53 | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="N01" | N1 || M || BE_SPI_CLK || ? || Connected to CELL 90nm pad AY13 (SPI Bus) | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="N02" | N2 || M || BE_SPI_DO || ? || Connected to CELL 90nm pad AV13 (SPI Bus) | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="N04" | N4 || A || SW_5_A || ? || Connected to [[Regulators#OnSemi_NCP5318FTR2G_.28Two.2FThree.2FFour-Phase_Buck_CPU_Controller.29|OnSemi NCP5318FTR2G]] (IC6201) pin 29<br>Connected to [[Components#Toshiba_TC7SG08FU_.282_Input_AND_Gate.29|Toshiba TC7SG08FU]] (IC6204) pin 1<br>Switches +1.2V_RSX_VDDC | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="N05" | N5 || A || BT_RESET || ? || Connected to wifi board connector (CN3701) pin 10 (named SYSCON_RST). This is a syscon output | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="N06" | N6 || A || AUDIO_MUTE || ? || Connected to transistor DTA144EUA-T106 (Q2404). Switches [[Components#Cirrus_CX4351-CZZR|Cirrus CX4351-CZZR]] pin 18 (AOUTA) left audio channel and pin 15 (AOUTB) right audio channel, that are connected to [[Connectors#AV_Multi_Out_pinout_-_CN2401_12P|MultiAV connector]] pin 11 (AUL) and pin9 (AUR) respectivelly | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="N07" | N7 || A || STBY_LED || ? || Connected to [[Switch_boards|Switch board]] [[CSW-001]] connector pin 7 | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="N08" | N8 || G || FANPWM0 || ? || Primary fan output (all PS3 models) | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="N09" | N9 || G || SW_PWM || ? || Connected to [[Switch_boards|Switch board]] [[CSW-001]] connector pin 2 | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="N10" | N10 || G || XDR_FET_SCK || ? || BE_RQ_SCK_BJT | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="N11" | N11 || G || SW_4_A || ? || Connected to wifi board connector (CN3701) pin 9 (named 11G_PWR_EN). This is a syscon output<br>Connected to base pin of transistor UMH2NTN (Q3501) who switches IC3502 pin 5, and IC3501 pin 3 (+1.2V_ESW, +1.9V_ESW, +3.3V_ESW for Ethernet Controller) | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="N12" | N12 || C || RSXVRM_VID0 || ? || Connected to [[Regulators#OnSemi_NCP5318FTR2G_.28Two.2FThree.2FFour-Phase_Buck_CPU_Controller.29|OnSemi NCP5318FTR2G]] (IC6201) pin 31 | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="N13" | N13 || C || RSXVRM_VID1 || ? || Connected to [[Regulators#OnSemi_NCP5318FTR2G_.28Two.2FThree.2FFour-Phase_Buck_CPU_Controller.29|OnSemi NCP5318FTR2G]] (IC6201) pin 32 | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="N15" | N15 || I || BACKUP_MODE || ? || Connected to [[Service_Connectors#CN4009| service connector]] (CN4009) pin 14 | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="N16" | N16 || I || DIAG_MODE || ? || Connected to [[Service_Connectors#CN4009| service connector]] (CN4009) pin 13 | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="P01" | P1 || M || BE_POWGOOD || ? || Connected to CELL 90nm pad AV20 | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="P02" | P2 || M || BE_RESET || ? || Connected to CELL 90nm pad AW20 | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="P15" | P15 || P || UART0_RxD || ? || Connected to [[Service_Connectors#CN4009| service connector]] (CN4009) pin 10 (Serial Receive) | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="P16" | P16 || P || UART0_TxD || ? || Connected to [[Service_Connectors#CN4009| service connector]] (CN4009) pin 11 (Serial Transmit) | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="R01" | R1 || M || PM7 || ? || | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="R02" | R2 || M || PM6 || ? || | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="R03" | R3 || <abbr title="Power port>PWR</abbr> || VDD1 || ? || +1.2V_MC2_VDDIO | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="R04" | R4 || <abbr title="Power port>PWR</abbr> || AVSUO || ? || Ground | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="R05" | R5 || <abbr title="Power port>PWR</abbr> || AVDUO || ? || +3.3V_EVER | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="R06" | R6 || <abbr title="Power port>PWR</abbr> || VSS || ? || Ground | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="R07" | R7 || <abbr title="Power port>PWR</abbr> || DVDD || ? || +1.8V_EVER | ||
|- | |- | ||
| data-sort-value="R08" | R8 || Q || RSX_FBVDD_SEL || ? || Connected to [[Components#Texas_Instruments_SN105233DBTR|Texas Instruments SN105233DBTR]] (IC6301) through transistor/s | | data-sort-value="R08" | R8 || Q || RSX_FBVDD_SEL || ? || Connected to [[Components#Texas_Instruments_SN105233DBTR|Texas Instruments SN105233DBTR]] (IC6301) through transistor/s | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="R09" | R9 || Q || PQ1 || ? || | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="R10" | R10 || Q || RMC_IN || ? || Connected to [[Switch_boards|Switch board]] [[CSW-001]] connector pin 3<br> Connected to [[Service_Connectors#CN4009| service connector]] (CN4009) pin 17 | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="R11" | R11 || B || VD_CECO0 || ? || | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="R12" | R12 || B || SW_3 || ? || Connected to [[Regulators#Rohm_BD3520FVM-TR_.28Single_channel_Regulator_Driver_IC.29|Rohm BD3520FVM-TR]] (IC6305) pin 3 (switches +1.2V_SB_VDDC and +1.2V_SB_VDDR) | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="R13" | R13 || B || SW_1_B || ? || Connected to [[Regulators#Mitsumi_MM1562ZFBE_.28Low-Saturation_500mA_Regulators.29 | Mitsumi MM1562ZFBE]] (IC6013) pin 5 (switches +2.5V_LREG_XCG_500_MEM)<br>Connected to [[Components#Toshiba_TC7WB66FK.28TE85R.29_.28low_on-resistance.2C_high-speed_CMOS2-bit_bus_switch.29|Toshiba TC7WB66FK]] (IC5005) pins 3 and 7, and to (IC5006) pin 4, through 1K resistor. The TC7WB66FK chip "duplicates" the MK_I2C_SCL/MK_I2C_SDA bus into a secondary XCG_I2C_SCL/XCG_I2C_SDA bus for the clock reference chip/s<br>Analog Voltage for the core PLL of IC5004, Clock Generator used to support the Rambus XDR memory subsystem and Redwood logic interface. | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="R14" | R14 || B || SW_7_A || ? || Connected to [[Regulators#OnSemi_NCP5318FTR2G_.28Two.2FThree.2FFour-Phase_Buck_CPU_Controller.29|OnSemi NCP5318FTR2G]] (IC6103) pin 29<br>Connected to [[Components#Toshiba_TC7SG08FU_.282_Input_AND_Gate.29|Toshiba TC7SG08FU]] (IC6107) pin 1<br>Switches +1.0V_BE_VDDC<br>Cell BE core voltage supply (VDD) then VCS (the core array voltage). Note, the VID values stored on the CELL itself are not available to be read yet. So the default VID of the VRM is used until then. | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="R15" | R15 || P || HDMI_I2C_SDA || ? || Connected to [[Sil9132CBU|HDMI controller Sil9132CBU]] pad D2 | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="R16" | R16 || P || HDMI_I2C_SCL || ? || Connected to [[Sil9132CBU|HDMI controller Sil9132CBU]] pad E2 | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="T01" | T1 || NC || NC || ? || Not connected | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="T02" | T2 || M || BE_INT || ? || Connected to CELL 90nm pad AW19 | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="T03" | T3 || <abbr title="Power port>PWR</abbr> || VSS || ? || Ground | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="T04" | T4 || <abbr title="Reset & Clock">RST</abbr> || XTAL || ? || Connected to crystal 16.9344Mhz | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="T05" | T5 || <abbr title="Reset & Clock">RST</abbr> || EXTAL || ? || Connected to crystal 16.9344Mhz | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="T06" | T6 || <abbr title="Power port>PWR</abbr> || VSS || ? || Ground | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="T07" | T7 || <abbr title="Reset & Clock">RST</abbr> || XXTALO || ? || Not connected (testpad CL4040) | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="T08" | T8 || Q || THR_I2C_SCL || ? || | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="T09" | T9 || Q || THR_I2C_SDA || ? || | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="T10" | T10 || Q || PQ4 || ? || | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="T11" | T11 || Q || PQ5 || ? || | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="T12" | T12 || B || VD_CECO1 || ? || | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="T13" | T13 || B || SW_4_B || ? || Connected to 88E6108 ethernet controller (IC3503) pin 94 (signal named P3_ENABLE_PD)<br>Connected to (Q6003) transistor (switches +3.3V_SB_VDDIO)<br>Connected to [[Regulators#OnSemi_NCP511SN25T1G_.282.5V_150_mA_CMOS_Low_Iq_Low-Dropout_Voltage_Regulator.29 | OnSemi NCP511SN25T1G]] (IC6011) pin 3 (switches +2.5V_SB_PLL_VDDC)<br>Connected to [[Regulators#Mitsumi_MM1591JFBEG_.28Low-Saturation_300mA_Regulators.29 | Mitsumi MM1591JFBEG]] (IC6014) pin 5 (switches +1.8V_SB_PERI)<br>Connected to UMH2NTN dual transistor (Q6006) pin 5 (switches +5V_USB) | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="T14" | T14 || B || SW_6 || ? || Connected to [[Regulators#Rohm_BD3520FVM-TR_.28Single_channel_Regulator_Driver_IC.29|Rohm BD3520FVM-TR]] (IC6303) pin 3 (switches +1.2V_YC_RC_VDDIO)<br>Connected to [[Regulators#Mitsumi_MM3141CNRE_.28150mA_Regulator_Monolithic.29 | Mitsumi MM3141CNRE]] (IC6012) pin 3 (switches +1.2V_MC2_VDDIO)<br>I/O voltage supplies, VDD_IO for [[CELL]], [[RSX]] and [[South Bridge]] | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="T15" | T15 || B || SW_8_A || ? || Connected to [[Regulators#Rohm_BD3504FVM-TR_.28Single_channel_Regulator_Driver_IC.29 | Rohm BD3504FVM-TR]] (IC6304) pin 3 (switches +1.5V_YC_RC_VDDA)<br>Connected to [[Regulators#Texas_Instruments_TPS73101DBVRG4_.28Single_Output_LDO.2C_150mA.2C_Adj._1.2-5.5V_SOT23-5.29 | Texas Instruments TPS73101DBVRG4]] (IC6007) pin 3 (switches +1.6V_BE_VDDA) | ||
|- | |- | ||
| data-sort-value=" | | data-sort-value="T16" | T16 || NC || NC || ? || Not connected | ||
|}</div><noinclude>[[Category:Templates]]</noinclude> | |}</div><noinclude>[[Category:Templates]]</noinclude> | ||
Revision as of 14:37, 20 October 2022
| Pad | Port | Name | Type | Description |
|---|---|---|---|---|
| A1 | NC | NC | ? | Not connected |
| A2 | J | DISC_IN | ? | Connected to BluRay Drive connector (CN3221) pin 52 |
| A3 | J | SW_0 | ? | Connected to Fujitsu MB39A116PFT (IC6003) pin 9 (switches +5V_MISC) Connected to Fujitsu MB39A116PFT (IC6003) pin 10 (switches +3.3V_MISC) Connected to Texas Instruments SN105233DBTR (IC6301) pin 10 (switches +1.7_MISC) |
| A4 | J | SW_8_C | ? | Connected to Texas Instruments SN105233DBTR (IC6301) pin 9 (switches +1.8V_RSX_FBVDDQ) Connected to OnSemi NCP511SN18T1 (IC6008) pin 3 (switches +1.8V_RSX_PLL_VDD) |
| A5 | J | DISC_OUT12_SW | ? | Connected to BluRay Drive connector (CN3221) pin 58 |
| A6 | R | MC_RESERVED2 | ? | Not connected to BluRay Drive because a missing resistor (R4080). BD_LED |
| A7 | R | MC_ALIVE | ? | Connected to BluRay Drive connector (CN3221) pin 47 |
| A8 | K | SB_SPI_CLK | ? | Southbridge SPI Bus |
| A9 | K | SB_SPI_DI | ? | Southbridge SPI Bus |
| A10 | K | DVE_I2C_SCL | ? | Connected to Digital Video Encoder CXM4024R pin 35 |
| A11 | K | ACDC_STBY | ? | Connected to Power Supply (small connector). This signal enables +12V_MAIN power rail (big prongs) |
| A12 | E | EJECT_SW | ? | Connected to Switch board CSW-001 connector pin 5 |
| A13 | E | SB_EBUS_RESET | ? | SS2_RESET (StarShip2 related), not connected because a missing resistor (R4135) ? |
| A14 | E | PE3 | ? | |
| A15 | E | BE_POW_FAIL | ? | Connected to OnSemi NCP5318FTR2G (IC6103) pin 7 |
| A16 | NC | NC | ? | Not connected |
| B1 | PWR | AVREF1 | ? | +3.3V_EVER |
| B2 | J | DISC_OUT8_SW | ? | Connected to BluRay Drive connector (CN3221) pin 57 |
| B3 | J | PJ3 | ? | Not connected in retail PS3 models (testpad CL4089) |
| B4 | J | SW_8_B | ? | Connected to Mitsumi MM1561JFBE (IC2408) pin 5 (switches +1.8V_ANA) Connected to Mitsumi MM1593DFBEG (IC2407) pin 5 (switches +3.3V_ANA) Connected to transistor DTC144EUA-T106 (Q2401) base pin (switches +5V_ANA ?) Connected to OnSemi NCP511SN15T1G (IC6019) pin 3 (switches +1.5V_AVCG_VDDIO) Connected to Rohm BD3521FVM-TR (IC6017) pin 3 (switches +1.5V_RSX_VDDIO) |
| B5 | J | DVE_RST | ? | Connected to Digital Video Encoder CXM4024R pin 31 ? |
| B6 | R | MC_P_OFF_REQ | ? | Connected to BluRay Drive connector (CN3221) pin 48 |
| B7 | R | MC_RESERVED1 | ? | Connected to BluRay Drive connector (CN3221) pin 49 |
| B8 | K | SB_SPI_DO | ? | Southbridge SPI Bus |
| B9 | K | SB_SPI_CS | ? | Southbridge SPI Bus |
| B10 | K | DVE_I2C_SDA | ? | Connected to Digital Video Encoder CXM4024R pin 36 |
| B11 | K | PK0 | ? | |
| B12 | E | POW_SW | ? | Connected to Switch board CSW-001 connector pin 4 |
| B13 | E | SB_EBUS_BRDY | ? | SS2_BRDY (StarShip2 related) |
| B14 | E | VD_CECI1 | ? | |
| B15 | E | POW_FAIL | ? | Connected to Mitsumi PST3642UL (IC6023) pin 4. Used to monitor the state of +12V_MAIN power rail |
| B16 | RST | OSCOUT | ? | Connected to crystal 32.768Khz |
| C1 | O | MK_I2C_SDA | ? | Connected to ICS1493G-18LFT clock generator (IC5001) pin 47 |
| C2 | PWR | AVREF2 | ? | Ground |
| C15 | PWR | VSSep | ? | EEPROM Ground |
| C16 | RST | OSCIN | ? | Connected to crystal 32.768Khz |
| D1 | O | MK_I2C_SCL | ? | Connected to ICS1493G-18LFT clock generator (IC5001) pin 46 |
| D2 | PWR | VDD2 | ? | +1.5V_RSX_VDDIO |
| D4 | O | XDR_FET_RST | ? | XDR_RQ_RST |
| D5 | O | XCG_EN | ? | Connected to ICS9218AGLFT (IC5002) pin 11 (switches BE_Y0_RQ_CTM/N, BE_Y1_RQ_CTM/N) Connected to ICS9218AGLFT (IC5003) pin 11 (switches BE_PLL_REFCLK_P/N) Connected to ICS9214DGLFT (IC5004) pin 11 (switches BE_RC_REFCLK_P/N, RSX_RC_REFCLK_P/N, SB_RC_REFCLK_P/N) |
| D6 | H | VD_CECI0 | ? | |
| D7 | H | RSX_POW_FAIL | ? | Connected to OnSemi NCP5318FTR2G (IC6201) pin 7 |
| D8 | H | MUL_TRG_IN | ? | Connected to missing components (IC4003, IC4004, IC4005) pin 3 and 6 (related with BE_TRG_IN/OUT, RSX_TRG_IN/OUT, SB_TRG_IN/OUT) |
| D9 | H | SB_INT | ? | |
| D10 | F | MUL_TRG_OUT | ? | Connected to missing components (IC4006) pin 2 (related with BE_TRG_IN/OUT, RSX_TRG_IN/OUT, SB_TRG_IN/OUT) |
| D11 | F | SB_RESET | ? | Connected to 88SA8040-TBC1 SATA2PATA BluRay controller pin 17 Connected to GL852 (IC3305) USB HUB pin 38 Connected to Multi-card-board connector CN3219 pin 7 |
| D12 | F | PF2 BE_VCS_1.25_ON |
? | COK-001/COK-002 PF2 (Not connected) SEM-001 BE_VCS_1.25_ON |
| D13 | F | SW_1_A | ? | Connected to Mitsumi MM1593DFBEG (IC6020) pin 5 (switches +3.3V_MK_VDD) for Clock Synthesizer |
| D15 | RST | 32KIN | ? | Connected to resistor 22ohm to pad D16 |
| D16 | RST | 32KOUT | ? | Connected to resistor 1K to +3.3V_EVER |
| E1 | PWR | VSS | ? | Ground |
| E2 | N | RSX_SPI_CS | ? | RSX SPI Bus |
| E4 | O | EJECT_MECHA | ? | Connected to BluRay Drive connector (CN3221) pin 56 |
| E5 | O | PO0 | ? | Not connected (testpad CL4086) |
| E6 | H | HDMI_INT | ? | Connected to TC7WP3125FK (IC2501) pin 6. This is a syscon input at 3.3V The TC7WP3125FK converts the signal originally triggered by Sil9132CBU pad E10 ? at 1.5V and converts it to 3.3V for syscon The TC7WP3125FK also converts the signal RS_SPDO0 (at 1.5V) into RS_SPDO0_33 (at 3.3V) |
| E7 | H | MECHA_INT | ? | Not connected in retail PS3 models (testpad CL4102). The related SouthBridge pad is tied to GND with a 10k resistor (R3163) |
| E8 | H | MUL_CHKSTP_IN | ? | SB_CHKSTP_OUT |
| E9 | H | SYS_THR_ALRT | ? | Connected to CELL 90nm pad AP23 |
| E10 | F | MUL_CHKSTP_OUT | ? | |
| E11 | F | SB_CGRESET | ? | SB_CGRST (the name indicates that it resets the clock generator for the southbridge) |
| E12 | F | BT_WAKEON | ? | Connected to wifi board connector (CN3701) pin 30 (named BT_WAKE). This is a syscon input |
| E13 | F | PF1 BE_VCS_1.30_ON |
? | COK-001/COK-002 PF1 (Not connected) SEM-001 BE_VCS_1.30_ON |
| E15 | EEP | PP3 | ? | |
| E16 | EEP | SKB | ? | |
| F1 | N | RSX_SPI_DI | ? | RSX SPI Bus |
| F2 | N | RSX_SPI_DO | ? | RSX SPI Bus |
| F4 | O | HDMI_RST0 | ? | Connected to HDMI controller Sil9132CBU pad G2 ? |
| F5 | O | DISC_IN_MECHA | ? | Connected to BluRay Drive connector (CN3221) pin 55 |
| F6 | PWR | VDD3 | ? | +3.3V_EVER |
| F7 | PWR | AVDD | ? | +3.3V_EVER |
| F8 | PWR | VDD3 | ? | +3.3V_EVER |
| F9 | NC | NC | ? | Not connected |
| F10 | PWR | VDD3 | ? | +3.3V_EVER |
| F11 | PWR | VDDbat | ? | +battery |
| F12 | D | MK_EN | ? | Connected to ICS1493G-18LFT clock generator (IC5001) pin 16 |
| F13 | D | SW_5_B | ? | Connected to Rohm BD3520FVM-TR (IC6200) pin 3 (switches +1.2V_RSX_VDDR) |
| F15 | EEP | PP0 | ? | |
| F16 | EEP | CSB | ? | |
| G1 | N | RSX_SPI_CLK | ? | RSX SPI Bus |
| G2 | N | RSX_RESET | ? | |
| G4 | O | HDMI_RST1 | ? | Not connected ? (it seems to be a secondary reset signal for HDMI controller Sil9132CBU never used in retail PS3 models) |
| G5 | O | SW_AVCG PO5 |
? | Connected to ICS422AG-07LFT (IC2102) pin 12 (switches RSX_AVCLK0, RSX_AVCLK1, RSX_AVCLK2, RSX_AVCLK3) clocks for RSX and indirectly for EEGS<->RDRAM |
| G6 | PWR | AVSS | ? | Ground |
| G7 | PWR | VSS | ? | Ground |
| G8 | PWR | VSS | ? | Ground |
| G9 | NC | NC | ? | Not connected |
| G10 | PWR | VSS | ? | Ground |
| G11 | PWR | VDDep | ? | EEPROM Power (+3.3V_EVER) |
| G12 | D | BEVRM_VID4 | ? | Connected to OnSemi NCP5318FTR2G (IC6103) pin 3 |
| G13 | D | BEVRM_VID5 | ? | Connected to OnSemi NCP5318FTR2G (IC6103) pin 30 |
| G15 | EEP | PP2 | ? | |
| G16 | EEP | DI | ? | |
| H1 | N | PN5 | ? | |
| H2 | N | PN6 | ? | |
| H4 | L | PL2 | ? | Not Connected |
| H5 | L | PL1 | ? | Not Connected |
| H6 | L | PL0 | ? | Not Connected |
| H7 | PWR | DVDD | ? | +1.8V_EVER |
| H10 | PWR | VDD3 | ? | +3.3V_EVER |
| H11 | RST | TESTMODE | ? | |
| H12 | D | BEVRM_VID2 | ? | Connected to OnSemi NCP5318FTR2G (IC6103) pin 1 |
| H13 | D | BEVRM_VID3 | ? | Connected to OnSemi NCP5318FTR2G (IC6103) pin 2 |
| H15 | EEP | PP1 | ? | |
| H16 | EEP | DO | ? | |
| J1 | N | RSX_FLDO1 | ? | |
| J2 | N | RSX_INT | ? | |
| J4 | L | PL4 | ? | Not Connected |
| J5 | L | PL3 | ? | Not Connected |
| J6 | PWR | VDD3 | ? | +3.3V_EVER |
| J7 | PWR | DVDD | ? | +1.8V_EVER |
| J10 | PWR | DVDD | ? | +1.8V_EVER |
| J11 | RST | RST | ? | Connected to service connector (CN4009) pin 8 |
| J12 | D | BEVRM_VID0 | ? | Connected to OnSemi NCP5318FTR2G (IC6103) pin 31 |
| J13 | D | BEVRM_VID1 | ? | Connected to OnSemi NCP5318FTR2G (IC6103) pin 32 |
| J15 | EEP | WCB | ? | |
| J16 | EEP | RBB | ? | |
| K1 | N | VD_VINT0 | ? | |
| K2 | N | VD_VINT1 | ? | |
| K4 | L | PL6 | ? | Not Connected |
| K5 | L | PL5 | ? | Not Connected |
| K6 | PWR | VSSF | ? | Ground |
| K7 | JTAG | JTDI | ? | Connected to service connector (CN4009) pin 3 |
| K8 | JTAG | JTCK | ? | Connected to service connector (CN4009) pin 5 |
| K9 | JTAG | JTDO | ? | Connected to service connector (CN4009) pin 6 |
| K10 | PWR | DVDD | ? | +1.8V_EVER |
| K11 | PWR | VSSF | ? | Ground |
| K12 | C | I2CBUS_EN | ? | Connected to Toshiba TC7WB66FK pins 3 and 7 (IC5005 on SEM-001) through 1K resistor (in COK-001 the resistor is missing, a.k.a. this syscon line is N/C). This chip "duplicates" the MK_I2C_SCL/MK_I2C_SDA bus into a secondary XCG_I2C_SCL/XCG_I2C_SDA bus for the clock reference chip/s |
| K13 | C | PC7 | ? | Not connected in retail PS3 models (testpad CL4085) |
| K15 | EEP | PI6 | ? | |
| K16 | EEP | PI7 | ? | |
| L1 | PWR | VSS | ? | Ground |
| L2 | PWR | VDD0 | ? | +1.2V_MC2_VDDIO |
| L4 | L | PL8 | ? | Not Connected |
| L5 | L | PL7 | ? | Not Connected |
| L6 | PWR | VDDF | ? | +3.3V_EVER |
| L7 | JTAG | JNTRST | ? | Connected to service connector (CN4009) pin 2 ? |
| L8 | JTAG | JRTCK | ? | Connected to service connector (CN4009) pin 4 |
| L9 | JTAG | JTMS | ? | Connected to service connector (CN4009) pin 7 |
| L10 | PWR | DVDD | ? | +1.8V_EVER |
| L11 | PWR | DVDD | ? | +1.8V_EVER |
| L12 | C | RSXVRM_VID4 | ? | Connected to OnSemi NCP5318FTR2G (IC6201) pin 3 |
| L13 | C | RSXVRM_VID5 | ? | Connected to OnSemi NCP5318FTR2G (IC6201) pin 30 |
| L15 | I | DISC_CHUCK | ? | Connected to BluRay Drive connector (CN3221) pin 54 |
| L16 | I | SW_PCI | ? | Connected to Mitsumi MM1591FFBEG (IC6021) pin 5 (switches +1.5V_BRIDGE) for the PS2 bridge CXD9208GP Connected to Mitsumi MM1593DFBEG (IC6022) pin 5 (switches +3.3V_BRIDGE) for the PS2 bridge CXD9208GP Connected to PCI service connector pin 80 |
| M1 | M | BE_SPI_DI | ? | Connected to CELL 90nm pad AR13 (SPI Bus) |
| M2 | M | BE_SPI_CS | ? | Connected to CELL 90nm pad AP13 (SPI Bus) |
| M4 | A | PA0 | ? | Not connected in retail PS3 models (testpad CL4092) |
| M5 | A | WLAN_RESET | ? | Connected to wifi board connector (CN3701) pin 29 (named 11G_RESET). This is a syscon output |
| M6 | A | PA4 | ? | Not connected in retail PS3 models (testpad CL4087) |
| M7 | A | POW_LED | ? | Connected to Switch board CSW-001 connector pin 6 |
| M8 | G | FANPWM1 | ? | Secondary fan output (non-retail PS3 models only) |
| M9 | G | BUZZER | ? | |
| M10 | G | XDR_FET_VREF | ? | Connected to transistor DTC144EUA-T106 (Q4008). Switches XDR_RQ_VREF_FET |
| M11 | G | SW_ATA | ? | Connected to UMH2NTN dual transistor (Q6009) pin 2 (switches +12V_BD) Connected to UMH2NTN dual transistor (Q6009) pin 5 (switches +5V_BD) Connected to UMH2NTN dual transistor (Q6006) pin 2 (switches +5V_HDD) |
| M12 | C | RSXVRM_VID2 | ? | Connected to OnSemi NCP5318FTR2G (IC6201) pin 1 |
| M13 | C | RSXVRM_VID3 | ? | Connected to OnSemi NCP5318FTR2G (IC6201) pin 2 |
| M15 | I | SW_2 | ? | Connected to Texas Instruments TPS51117PWRG4 (IC6302) pin 1 (switches +1.8V_VDD_MEM) |
| M16 | I | DISC_PHOT_LED | ? | Connected to BluRay Drive connector (CN3221) pin 53 |
| N1 | M | BE_SPI_CLK | ? | Connected to CELL 90nm pad AY13 (SPI Bus) |
| N2 | M | BE_SPI_DO | ? | Connected to CELL 90nm pad AV13 (SPI Bus) |
| N4 | A | SW_5_A | ? | Connected to OnSemi NCP5318FTR2G (IC6201) pin 29 Connected to Toshiba TC7SG08FU (IC6204) pin 1 Switches +1.2V_RSX_VDDC |
| N5 | A | BT_RESET | ? | Connected to wifi board connector (CN3701) pin 10 (named SYSCON_RST). This is a syscon output |
| N6 | A | AUDIO_MUTE | ? | Connected to transistor DTA144EUA-T106 (Q2404). Switches Cirrus CX4351-CZZR pin 18 (AOUTA) left audio channel and pin 15 (AOUTB) right audio channel, that are connected to MultiAV connector pin 11 (AUL) and pin9 (AUR) respectivelly |
| N7 | A | STBY_LED | ? | Connected to Switch board CSW-001 connector pin 7 |
| N8 | G | FANPWM0 | ? | Primary fan output (all PS3 models) |
| N9 | G | SW_PWM | ? | Connected to Switch board CSW-001 connector pin 2 |
| N10 | G | XDR_FET_SCK | ? | BE_RQ_SCK_BJT |
| N11 | G | SW_4_A | ? | Connected to wifi board connector (CN3701) pin 9 (named 11G_PWR_EN). This is a syscon output Connected to base pin of transistor UMH2NTN (Q3501) who switches IC3502 pin 5, and IC3501 pin 3 (+1.2V_ESW, +1.9V_ESW, +3.3V_ESW for Ethernet Controller) |
| N12 | C | RSXVRM_VID0 | ? | Connected to OnSemi NCP5318FTR2G (IC6201) pin 31 |
| N13 | C | RSXVRM_VID1 | ? | Connected to OnSemi NCP5318FTR2G (IC6201) pin 32 |
| N15 | I | BACKUP_MODE | ? | Connected to service connector (CN4009) pin 14 |
| N16 | I | DIAG_MODE | ? | Connected to service connector (CN4009) pin 13 |
| P1 | M | BE_POWGOOD | ? | Connected to CELL 90nm pad AV20 |
| P2 | M | BE_RESET | ? | Connected to CELL 90nm pad AW20 |
| P15 | P | UART0_RxD | ? | Connected to service connector (CN4009) pin 10 (Serial Receive) |
| P16 | P | UART0_TxD | ? | Connected to service connector (CN4009) pin 11 (Serial Transmit) |
| R1 | M | PM7 | ? | |
| R2 | M | PM6 | ? | |
| R3 | PWR | VDD1 | ? | +1.2V_MC2_VDDIO |
| R4 | PWR | AVSUO | ? | Ground |
| R5 | PWR | AVDUO | ? | +3.3V_EVER |
| R6 | PWR | VSS | ? | Ground |
| R7 | PWR | DVDD | ? | +1.8V_EVER |
| R8 | Q | RSX_FBVDD_SEL | ? | Connected to Texas Instruments SN105233DBTR (IC6301) through transistor/s |
| R9 | Q | PQ1 | ? | |
| R10 | Q | RMC_IN | ? | Connected to Switch board CSW-001 connector pin 3 Connected to service connector (CN4009) pin 17 |
| R11 | B | VD_CECO0 | ? | |
| R12 | B | SW_3 | ? | Connected to Rohm BD3520FVM-TR (IC6305) pin 3 (switches +1.2V_SB_VDDC and +1.2V_SB_VDDR) |
| R13 | B | SW_1_B | ? | Connected to Mitsumi MM1562ZFBE (IC6013) pin 5 (switches +2.5V_LREG_XCG_500_MEM) Connected to Toshiba TC7WB66FK (IC5005) pins 3 and 7, and to (IC5006) pin 4, through 1K resistor. The TC7WB66FK chip "duplicates" the MK_I2C_SCL/MK_I2C_SDA bus into a secondary XCG_I2C_SCL/XCG_I2C_SDA bus for the clock reference chip/s Analog Voltage for the core PLL of IC5004, Clock Generator used to support the Rambus XDR memory subsystem and Redwood logic interface. |
| R14 | B | SW_7_A | ? | Connected to OnSemi NCP5318FTR2G (IC6103) pin 29 Connected to Toshiba TC7SG08FU (IC6107) pin 1 Switches +1.0V_BE_VDDC Cell BE core voltage supply (VDD) then VCS (the core array voltage). Note, the VID values stored on the CELL itself are not available to be read yet. So the default VID of the VRM is used until then. |
| R15 | P | HDMI_I2C_SDA | ? | Connected to HDMI controller Sil9132CBU pad D2 |
| R16 | P | HDMI_I2C_SCL | ? | Connected to HDMI controller Sil9132CBU pad E2 |
| T1 | NC | NC | ? | Not connected |
| T2 | M | BE_INT | ? | Connected to CELL 90nm pad AW19 |
| T3 | PWR | VSS | ? | Ground |
| T4 | RST | XTAL | ? | Connected to crystal 16.9344Mhz |
| T5 | RST | EXTAL | ? | Connected to crystal 16.9344Mhz |
| T6 | PWR | VSS | ? | Ground |
| T7 | RST | XXTALO | ? | Not connected (testpad CL4040) |
| T8 | Q | THR_I2C_SCL | ? | |
| T9 | Q | THR_I2C_SDA | ? | |
| T10 | Q | PQ4 | ? | |
| T11 | Q | PQ5 | ? | |
| T12 | B | VD_CECO1 | ? | |
| T13 | B | SW_4_B | ? | Connected to 88E6108 ethernet controller (IC3503) pin 94 (signal named P3_ENABLE_PD) Connected to (Q6003) transistor (switches +3.3V_SB_VDDIO) Connected to OnSemi NCP511SN25T1G (IC6011) pin 3 (switches +2.5V_SB_PLL_VDDC) Connected to Mitsumi MM1591JFBEG (IC6014) pin 5 (switches +1.8V_SB_PERI) Connected to UMH2NTN dual transistor (Q6006) pin 5 (switches +5V_USB) |
| T14 | B | SW_6 | ? | Connected to Rohm BD3520FVM-TR (IC6303) pin 3 (switches +1.2V_YC_RC_VDDIO) Connected to Mitsumi MM3141CNRE (IC6012) pin 3 (switches +1.2V_MC2_VDDIO) I/O voltage supplies, VDD_IO for CELL, RSX and South Bridge |
| T15 | B | SW_8_A | ? | Connected to Rohm BD3504FVM-TR (IC6304) pin 3 (switches +1.5V_YC_RC_VDDA) Connected to Texas Instruments TPS73101DBVRG4 (IC6007) pin 3 (switches +1.6V_BE_VDDA) |
| T16 | NC | NC | ? | Not connected |