Syscon Hardware: Difference between revisions
Strike Venom (talk | contribs) m (→Retail) |
Strike Venom (talk | contribs) No edit summary |
||
Line 114: | Line 114: | ||
</pre> | </pre> | ||
= Syscon (SPI) EEPROM = | |||
Pinout (external): | |||
{| class="wikitable" | |||
! Pin !! Description | |||
|- | |||
| CSB || Chip Select (needs always 3.3V <!--low-->) | |||
|- | |||
| DO || Serial Data Output | |||
|- | |||
| DI || Serial Data Input | |||
|- | |||
| SKB || Serial Data Clock | |||
|- | |||
| WCB || Write Protect | |||
|- | |||
| RBB || Read Data back (Verify) | |||
|} | |||
{{Models}} | {{Models}} | ||
[[Category:System Controller]] | [[Category:System Controller]] |
Revision as of 12:07, 24 April 2013
Syscon is the main power controller chip. It is responsible for powering up the various power systems and for configuring and initialising the CELL BE, RSX and South Bridge. It communicates with these devices via seperate SPI busses. There is external access by JTAG (disabled at factory by blowing a fuse), an EEPROM programming interface and Serial (UART). The Syscon is a SoC and consists of an ARM7TDMI (ARMv4) CPU, a 256KB EEPROM and 16KB RAM.
Serialnumbers @ SKU
Retail
Model | Type | Board | Syscon part no. |
Soft Id. |
Notes | |
---|---|---|---|---|---|---|
CECHAxx | 0x01 | COK-001 | CXR713120-201GB | 0B8E | ||
CECHBxx | 0x02 | COK-001 | CXR713120-201GB | 0B8E | ||
CECHCxx | 0x03 | COK-002 | CXR713120-201GB | 0C16 | ||
CECHDxx | SKU never released | |||||
CECHExx | 0x04 | COK-002 or COK-002W |
CXR713120-201GB | 0C16 | ||
CECHFxx | SKU never released | |||||
CECHGxx | 0x05 | SEM-001 | CXR713120-201GB | 0D52 | ||
CECHHxx | 0x06 | DIA-001 | CXR714120-301GB | 0DBF | ||
CECHIxx | SKU never released | |||||
CECHJxx | 0x07 | DIA-002 | CXR714120-301GB | 0E69 | ||
CECHKxx | 0x07 | DIA-002 | CXR714120-301GB or CXR714120-302GB |
0E69 | ||
CECHLxx | 0x08 | VER-001 | SW-301 or SW-302 |
065D | ||
CECHMxx | 0x08 | VER-001 | SW-301 or SW-302 |
065D | ||
CECHNxx | SKU never released | |||||
CECHOxx | SKU never released | |||||
CECHPxx | 0x08 | VER-001 | SW-301 or SW-302 |
065D | ||
CECHQxx | 0x08 | VER-001 | SW-301 or SW-302 |
065D | ||
CECH-20xx | 0x09 | DYN-001 | SW2-301 | 0832 | ||
CECH-21xx | 0x0A | SUR-001 | SW2-301 or SW2-302 |
08A0 | ||
CECH-25xx | 0x0B | JTP-001 or JSD-001 |
SW2-301 or SW2-302 or SW2-303 |
08C2 | ||
CECH-30xx | 0x0C | KTE-001 | SW2-301 or SW2-302 or SW2-303 |
0918 | ||
CECH-40xx | 0x0D | MSX-001 or MPX-001 |
SW3-302 | 098F |
Prototypes
Model | Type | Board | Syscon part no. |
Soft Id. |
Active JTAG | Notes |
---|---|---|---|---|---|---|
DECR1000(A/J) | 0x01 | TMU-520 | CXR713F120A | 03FB | ? | |
DEH-H1000A(S)(-E(S)) | 0x01 | COK-001 (Prototype) | CXR713F120A | 0B67 | ? | |
DEH-H1001-D | 0x01 | COOKIE-13 | CXR713F120A | ?0B67? | ? |
Not mentioned:
0F29 - ? 0F38 - ?
Syscon UART
You can attach a 3.3v TTL cable (LV-TTL) to the UART on syscon (UART0_TxD, UART0_RxD). Baud rate is 57600. There is a simple plaintext protocol involved. This varies on different syscon models. Example:
<command>:<hash>
Where the hash is the sum of command bytes & 0xFF
you should terminate commands with \r\n, the syscon messages are only terminated with \n
Here are some of the commands/messages encountered:
Messages: Power applied (standby mode) OK 00000000:3A Power on # (PowerOn State):7F Power off (Hard shutdown) # (PowerOff State):DD After Fan test: # (PowerOff State) (Fatal):36 No text, invalid hash: NG F0000002:4D Commands: VER:ED OK 00000000 S1E 00 00 065D:A4 ERRLOG:CB OK 00000000:3A DATE:1E NG F0000003:4E
Syscon (SPI) EEPROM
Pinout (external):
Pin | Description |
---|---|
CSB | Chip Select (needs always 3.3V ) |
DO | Serial Data Output |
DI | Serial Data Input |
SKB | Serial Data Clock |
WCB | Write Protect |
RBB | Read Data back (Verify) |