Template:Syscon pinout LQFP 128 pins

From PS3 Developer wiki
Revision as of 07:08, 18 March 2022 by Sandungas (talk | contribs)
Jump to navigation Jump to search


Pinout

Syscon pinout LQFP 128 pins
NEC/Renesas 78K0R/KH3 Optional pin configurations

Syscon SW2-303 unsoldered
CECH-25xx with JTP-001 or JSD-001 motherboard

Syscon SW2-303
CECH-25xx with JTP-001 or JSD-001 motherboard

Syscon SW-301
CECHLxx with VER-001 motherboard
[ View ], [ Discuss ] or [ Edit ]
Syscon pinout LQFP 128 pins
[ View ], [ Discuss ] or [ Edit ]
Pin Port Name Type Description STBY Voltages
NEC/Renesas Sony/Custom
1 14 P142/SCK20/SCL20 HDMI_I2C_SCL ?
In
 Connected to HDMI controller MN8647091 pin 27 0
2 14 P141/PCLBUZ1/INTP7 SB_INT/SYSCSINT
In
 Connected to South Bridge CXD9963GB pad D1 through a resistor ~1V @ standby (0 V?)
3 14 P140/PCLBUZ0/INTP6 BE_INT/ATTENTION
In
 Connected to CELL pad BA17 through a NPN transistor (CELL switches the transistor to connect this pin to GND) 3V @ standby (3.15V)
4 12 P120/INTP0/EXLVI
In/Out
 Connected to +12V_MAIN through a resistor and divider (EXLVI config = External potential input for low-voltage detector ?) 0
5 3 P37 POW_LED
Out
 Connected to Switch board dual led (Green) through a dual digital NPN transistor EMH1(SOT-563) 0
6 3 P36 STBY_LED
Out
 Connected to Switch board dual led (Red) through a dual digital NPN transistor EMH1(SOT-563) 3v @ standby (3.3V)
7 3 P35
In/Out
 Connected to South Bridge CXD9963GB pad AA18 0
8 3 P34
In/Out
 Connected to South Bridge CXD9963GB pad AA17 0
9 3 P33
In/Out
 CELL BE related? 0
10 3 P32
In/Out
 0
11 16 P163/TI13/TO13 BACK_LEDS
Out
 Connected to Switch board backlit LEDs through a transistor 0
12 16 P162/TI12/TO12 SW_PWM ?
Out
 Connected to Switch board contour LEDs through a transistor 0
13 16 P161/TI11/TO11
Others
 NOT_CONNECTED. Floating through a missing SMD component. See: NOWHERE 0
14 16 P160/TI10/TO10
Others
 NOT_CONNECTED. Floating through a missing SMD component at the other side of the board. See: VIA 0
15 4 P47/INTP2 BT_WAKEON ?
In/Out
 Connected to Wifi/BT module 0
16 4 P46/INTP1/TI05/TO05 BUZZER
Out
 Connected to the Buzzer through a transistor 0
17 4 P45/SO01
In/Out
 Connected to South Bridge CXD9963GB ? (SB_SPI_DO) 0
18 4 P44/SI01
In/Out
 Connected to South Bridge CXD9963GB ? (SB_SPI_DI) 3v @ standby
19 4 P43/SCK01
In/Out
 Connected to South Bridge CXD9963GB ? (SB_SPI_CLK) 0
20 4 P42/TI04/TO04
In/Out
 Connected to South Bridge CXD9963GB ? (SB_SPI_CS) 0
21 4 P41/TOOL1 TOOL_CLK
Out
 Connected to Service Connector 3rd Gen. pin 13 (Tool clock) through a missing resistor 3.0
22 4 P40/TOOL0 TOOL_DAT
In/Out
 Connected to Service Connector 3rd Gen. pin 7 (Tool Data) through a missing resistor 0
23 12 P127/SO21
In/Out
 0
24 12 P126/SI21/SDA21 THR_I2C_SDA
In/Out
 Connected to Temperature Monitors pin 7 (SMBus data) 3v @ standby (3.15)
25 12 P125/SCK21/SCL21 THR_I2C_SCL
Out
 Connected to Temperature Monitors pin 8 (SMBus clock) 3v @ standby (3.15)
26 RESET RESET
In
 Connected to Service Connector 3rd Gen. pin 9 through a missing resistor
Connected to standby voltage regulator 463A pin 3
27 12 P124/XT2 XT_SUB/OSCOUT ?
In
 Connected to a crystal (Subsystem clock). CLK -> 1-2V Amplitude (32.768Khz)
28 12 P123/XT1 XT_SUB/OSCIN ?
In
 Connected to a crystal (Subsystem clock). CLK -> 1-2V Amplitude (32.768Khz)
29 FLMD0 FLASH_MODE
Others
 Connected to Service Connector 3rd Gen. pin 8 (Flash programming mode) through a missing resistor 3.33
30 12 P122/X2/EXCLK XT_MAIN/XTAL ?
In
 Connected to a crystal (Main system clock) marked "EX" (16.9344Mhz?) 0.8v @ standby (1.1)
31 12 P121/X1 XT_MAIN/EXTAL ?
In
 Connected to a crystal (Main system clock) marked "EX" (16.9344Mhz?) 2.2v @ standby (2.4)
32 REGC VREG_CAP
Others
 Connected to battery+ through 2 diodes
Connected to a capacitor (internal voltage regulator, around 1uF) at the other side of the board. See: VIA
33 VSS0 GND
Others
 0
34 EVSS0 GND
Others
 0
35 VDD 3.3_EVER_B
Others
 Connected to standby voltage regulator 463A pin 2 3v @ standby (3.3)
36 EVDD0 3.3_EVER_B
Others
 Connected to standby voltage regulator 463A pin 2 3v @ standby (3.3)
37 6 P60/SCL0 MK_I2C_SCL
In/Out
 Connected to Texas Instruments-SCEI Clock Generator CDC972 pin 37 0.2v @ standby
38 6 P61/SDA0 MK_I2C_SDA
In/Out
 Connected to Texas Instruments-SCEI Clock Generator CDC972 pin 38 0.2v @ standby
39 6 P62
In/Out
 0
40 6 P63 P63_DOWN
In
 10K resistor to GND 0
41 3 P31/TI03/TO03/INTP4 ACIN_DET
In
 Connected to Power Supply control connector pin 4 through a transistor. See: schematic 3v @ standby (3.3)
42 6 P64/RD
In/Out
 Connected to voltage regulator BD9684 0906 pin 4 (enable something) through some undocumented components 0
43 6 P65/WR0
In/Out
 Connected to Service Connector 3rd Gen. pin 12 through a missing resistor 3.0
44 6 P66/WR1
In/Out
 0
45 6 P67/ASTB
Others
 NOT_CONNECTED. 0
46 7 P77/EX23/KR7/INTP11
Out
 Connected to CELL BE through a transistor (labeled 26 and located near the CELL temperature monitor)
It seems to be some kind of ALERT signal (inverted direction than the signal from pin 109)		 0
47 7 P76/EX22/KR6/INTP10
In/Out
 3v @ standby (3.15)
48 7 P75/EX21/KR5/INTP9
In
 Connected to RSX through a transistor (labeled ND and located near the RSX temperature monitor)
It seems to be some kind of ALERT signal		 3v @ standby (3.15)
49 7 P74/EX20/KR4/INTP8 INTP8_DOWN
In
 10K resistor to GND 0
50 7 P73/EX19/KR3
In/Out
 Connected to Service Connector 3rd Gen. pin 3
Connected to voltage regulator D35653 0S25 (FLASH_ENABLE ?)		 0
51 7 P72/EX18/KR2
In/Out
 Connected to xxxxxxxxxxxxxx through transistor 0
52 7 P71/EX17/KR1
In/Out
 Connected to voltage regulator BD3525 pin 12 (enable something) 0
53 7 P70/EX16/KR0
In/Out
 0
54 0 P06/WAIT P06_DOWN
In/Out
 45K resistor array to GND 0
55 0 P05/CLKOUT P05_DOWN
In/Out
 45K resistor array to GND 0
56 EVSS1 GND
Others
 0
57 EVDD1 3.3_EVER_B
Others
 Connected to standby voltage regulator 463A pin 2 3v @ standby (3.3)
58 8 P80/EX0
In/Out
 0
59 8 P81/EX1
In/Out
 0
60 8 P82/EX2
In/Out
 0
61 8 P83/EX3
In/Out
 0
62 8 P84/EX4
In/Out
 0
63 8 P85/EX5
In/Out
 0
64 8 P86/EX6
In/Out
 0
65 8 P87/EX7
In/Out
 0
66 3 P30/INTP3/RTC1HZ
In/Out
 0
67 5 P50/EX8
In/Out
 0
68 5 P51/EX9
In/Out
 0
69 5 P52/EX10
In/Out
 0
70 5 P53/EX11
In/Out
 0
71 5 P54/EX12
In/Out
 0
72 5 P55/EX13
In/Out
 0
73 5 P56/EX14
In/Out
 0
74 5 P57/EX15
In/Out
 0
75 1 P17/EX31/TI02/TO02
In/Out
 Connected to voltage regulator Mitsumi 040 810X pin 5 0
76 1 P16/EX30/TI01/TO01/INTP5
In
 Connected to RSX through a transistor (labeled ND and located near the RSX temperature monitor)
It seems to be some kind of ALERT signal		 3v @ standby (3.15)
77 1 P15/EX29/RTCDIV/RTCCL
In/Out
 3v @ standby (3.3)
78 1 P14/EX28/RxD3 SC_RxD
In
 Connected to Service Connector 3rd Gen. pin 11 (UART-TTL terminal Receive) through a missing resistor
Connected to PCI Connector pin 6		 0
79 1 P13/EX27/TxD3 SC_TxD
Out
 Connected to Service Connector 3rd Gen. pin 10 (UART-TTL terminal Transmit) through a missing resistor
Connected to PCI Connector pin 4		 3.3
80 1 P12/EX26/SO00/TxD0 BE_SPI_DI
Out
 Connected to CELL pad. (MOSI) Serial Output from Syscon Master to Cell Slave 0
81 1 P11/EX25/SI00/RxD0 BE_SPI_DO
In
 Connected to CELL pad. (MISO) Serial Input from Cell Slave to Syscon Master 1.2
82 1 P10/EX24/SCK00 BE_SPI_CLK Connected to CELL pad. 2.5 Mhz SPI Clock
83 9 P90/EX32 /BE_SPI_CS
In/Out
 Connected to CELL pad. Chip Select 2.0
84 9 P91/EX33
In/Out
 3v @ standby
85 9 P92/EX34
In/Out
 0
86 9 P93/EX35
In/Out
 0
87 9 P94
In/Out
 Connected to RSX pad AW8 ? (RSX_SPI_CS). See: Template:RSX pad layout 41x41 and pad AW8 0
88 9 P95/SCK11/SCL11
In/Out
 Connected to RSX pad AY8 ? (RSX_SPI_CLK ). See: Template:RSX pad layout 41x41 and pad AY8 0
89 9 P96/SI11/SDA11
In/Out
 Connected to RSX pad BA7 ? (RSX_SPI_DI). See: Template:RSX pad layout 41x41 and pad BA7 0
90 9 P97/SO11
In/Out
 Connected to RSX pad BS6 ? (RSX_SPI_DO). See: Template:RSX pad layout 41x41 and pad BA6 0
91 11 P112
In/Out
 0
92 11 P113
In/Out
 Connected to voltage regulator BD3527 pin 12 (located near FLASH) 0
93 11 P114
In/Out
 0
94 11 P115
In/Out
 Connected to xxxxxxxxxxxxxx through transistor 0
95 11 P116
In/Out
 Connected to voltage regulator BD3527 pin 12 (located near USB) 0
96 11 P117 AV_EN
Out
 Connected to MultiAV connector pin 3 (+5V output) through a transistor 0
97 AVREF1 3.3_EVER_B
Others
 Connected to standby voltage regulator 463A pin 2 3v @ standby (3.3)
98 11 P110/ANO0
Others
 NOT_CONNECTED. 0
99 11 P111/ANO1
Others
 NOT_CONNECTED. 0
100 AVREF0 3.3_EVER_B
Others
 Connected to standby voltage regulator 463A pin 2 3v @ standby (3.3)
101 AVSS0 GND
Others
 0
102 15 P157/ANI15 ANI15_DOWN
In
 100k resistor to GND. And to a missing SMD component to VIA to pin 8 of voltage regulator 463A (3.3_EVER_A) 0
103 15 P156/ANI14 ANI14_UP
In
 VIA to 100k resistor to pin 8 of voltage regulator 463A (3.3_EVER_A) 0
104 15 P155/ANI13 ANI13_DOWN
In
 VIA to 100k resistor to GND 0
105 15 P154/ANI12
Others
 NOT_CONNECTED. 0
106 15 P153/ANI11
Others
 NOT_CONNECTED. 0
107 15 P152/ANI10
Others
 NOT_CONNECTED. 0
108 15 P151/ANI9
Others
 NOT_CONNECTED. 0
109 15 P150/ANI8 ANI8_UP_UNK
In
 Connected to CELL BE through a transistor (labeled ND and located near the CELL temperature monitor)
It seems to be some kind of ALERT signal (inverted direction than the signal from pin 46)
And to 10k resistor to VIA to pin 8 of voltage regulator 463A (3.3_EVER_A)		 3v @ standby
110 2 P27/ANI7 POW_SW
In
 Connected to Switch board power switch 3v @ standby (3.3) 3.3
111 2 P26/ANI6 EJECT_SW
In
 Connected to Switch board eject switch 3v @ standby (3.3) 3.3
112 2 P25/ANI5 WIFI_DATA_1
In/Out
 Connected to Wifi/BT module 0
113 2 P24/ANI4 WIFI_DATA_2
In/Out
 Connected to Wifi/BT module 0
114 2 P23/ANI3
In/Out
 0
115 2 P22/ANI2
In/Out
 0
116 2 P21/ANI1
In/Out
 0
117 2 P20/ANI0
In/Out
 (0V?)
118 13 P130 ACDC_STBY
Out
 Connected to Power Supply control connector pin 3 through a 2K2ohm resistor. See: schematic 3v @ standby (3.3)
119 13 P131/TI06/TO06 HDMI_EN
Out
 Connected to HDMI controller MN8647091 (primary and secondary power inputs) through voltage regulator 348A pins 2 and 7
Connected to HDMI connector pin 18 (+5V output) through a transistor		 3v @ standby (3.3)
120 0 P07
In/Out
 0
121 0 P04/SCK10/SCL10 DVE_I2C_SCL
In/Out
 Connected to Digital Video Encoder CXM4027R pin 35 0
122 0 P03/SI10/RxD1/SDA10 DVE_I2C_SDA
In/Out
 Connected to Digital Video Encoder CXM4027R pin 36 0
123 0 P02/SO10/TxD1
In/Out
 0
124 0 P01/TO00
In/Out
 Connected to HDMI controller MN8647091 pin 93 0
125 0 P00/TI00
In/Out
 0
126 14 P145/TI07/TO07 FANPWM0
Out
 Connected to the FAN grey wire (PWM duty) 0
127 14 P144/SO20/TxD2
In/Out
 0
128 14 P143/SI20/RxD2/SDA20 HDMI_I2C_SDA ?
In/Out
 Connected to HDMI controller MN8647091 pin 29 0
Retrieved from "http://www.psdevwiki.com/ps3/index.php?title=Template:Syscon_pinout_LQFP_128_pins&oldid=66025"