Template:Syscon pinout LQFP 128 pins
Jump to navigation
Jump to search
Pin # | Name | Port | Description | STBY Voltages |
---|---|---|---|---|
1 | P142/SCK20/SCL20 | Connected to pin27 @Panasonic MN8647091 | 0 | |
2 | SB_INT | SB_INT/SYSCSINT, Connected to pinD1@SB through the resistor. ~1V @ standby (0 V?) | 0 | |
3 | BE_INT | BE_INT/ATTENTION, pinBA17@BE connected through the NPN transistor. 3V @ standby (3.15V) | 3.15 | |
4 | To +12V_MAIN through the resistor and divider | 0 | ||
5 | P37/POW_LED | Connected to dual led(Green) on switch board through the dual digital NPN trans. EMH1(SOT-563) | 0 | |
6 | P36/STBY_LED | Connected to dual led(Red) on switch board through the dual digital NPN trans. EMH1(SOT-563) | 3v @ standby (3.3V) | |
7 | Connected to pinAA18@SB | 0 | ||
8 | Connected to pinAA17@SB | 0 | ||
9 | CELL BE related? | 0 | ||
10 | 0 | |||
11 | P106 | Connected to Backlit LEDs on switch board | 0 | |
12 | P105 | Connected to CONTOUR LEDs on switch board | 0 | |
13 | P104 | Absent element between this line and GND. Nothing else. | 0 | |
14 | 0 | |||
15 | INTP?? | 0 | ||
16 | BUZZER | 0 | ||
17 | P45/SO01 | 0 | ||
18 | P44/SI01 | 3v @ standby | 3.0 | |
19 | P43/SCK01 | 0 | ||
20 | 0 | |||
21 | TOOL1 | Connected to Pin 13 @ Service Connector through a missing SMD component resistor/diode | 3.0 | |
22 | TOOL0/Debugger Pin? | Connected to Pin 7 @ Service Connector through a missing SMD component resistor/diode | 0 | |
23 | P127/SO21 | 0 | ||
24 | P126/THR_I2C_SDA | Connected to pin 7 of CELL/RSX temperature monitor IC's (SMbus I2C shared data line) | 3v @ standby (3.15) | |
25 | P125/THR_I2C_SCL | Connected to pin 8 of CELL/RSX temperature monitor IC's (SMbus I2C shared clock line) | 3v @ standby (3.15) | |
26 | RESET? | Connected to Pin 9 @ Service Connector through a missing SMD component resistor/diode. And to standby voltage regulator 463A, pin 3 | ||
27 | P124 | Connected to the big black external oscilator 1 next to syscon. CLK -> 1-2V Amplitude (32.768Khz?) | ||
28 | P123 | Connected to the big black external oscilator 1 next to syscon. CLK -> 1-2V Amplitude (32.768Khz?) | ||
29 | P137/FLMD0 | Connected to pin 8 @ Service Connector through a missing SMD component resistor/diode | 3.33 | |
30 | P122 | Connected to a small external oscilator 2 ? | 0.8v @ standby (1.1) | |
31 | P121 | Connected to a small external oscilator 2 ? | 2.2v @ standby (2.4) | |
32 | REGC | |||
33 | GROUND/Vss0 | 0 | ||
34 | GROUND/EVss0 | 0 | ||
35 | Vdd | Connected to voltage regulator 463A, pin 2 (3.3_EVER_B) | 3v @ standby (3.3) | |
36 | EVdd0 | Connected to voltage regulator 463A, pin 2 (3.3_EVER_B) | 3v @ standby (3.3) | |
37 | P60 | 0.2v @ standby | 0 | |
38 | P61 | 0.2v @ standby | 0 | |
39 | 0 | |||
40 | 0 | |||
41 | P31/AC IN? | 3v @ standby (3.3) | 3.3 | |
42 | Connected (indirectly) to voltage regulator BD9684 0906, pin 4 | 0 | ||
43 | P65 | Connected to Pin 12 @ Service Connector through a missing SMD component resistor/diode | 3.0 | |
44 | 0 | |||
45 | 0 | |||
46 | INTP?? | 0 | ||
47 | P76 | 3v @ standby (3.15) | 3.15 | |
48 | P75 | 3v @ standby (3.15) | 3.15 | |
49 | INTP?? | 0 | ||
50 | P73 | Connected to pin 3 @ Service Connector. And to voltage regulator D35653 0S25 | 0 | |
51 | 0 | |||
52 | Connected to voltage regulator BD3525, pin 12 | 0 | ||
53 | 0 | |||
54 | 0 | |||
55 | 0 | |||
56 | GROUND/EVss1 | 0 | ||
57 | EVdd1 | Connected to voltage regulator 463A, pin 2 (3.3_EVER_B) | 3v @ standby (3.3) | |
58 | 0 | |||
59 | 0 | |||
60 | 0 | |||
61 | 0 | |||
62 | 0 | |||
63 | 0 | |||
64 | 0 | |||
65 | 0 | |||
66 | INTP?? | 0 | ||
67 | 0 | |||
68 | 0 | |||
69 | 0 | |||
70 | 0 | |||
71 | 0 | |||
72 | 0 | |||
73 | 0 | |||
74 | 0 | |||
75 | Connected to voltage regulator Mitsumi 040 810X, pin 5 | 0 | ||
76 | P16 | 3v @ standby (3.15) | 3.15 | |
77 | P15 | 3v @ standby (3.3) | 3.3 | |
78 | SC_RxD(RxD3/RxD2/P14) | SC_RxD UART (terminal).Connected to Pin 11 @ Service Connector through a missing SMD component resistor/diode, and to pin 6 @ PCI Connector | 0 | |
79 | SC_TxD(TxD3/TxD2/P13) | SC_TxD UART (terminal).Connected to Pin 10 @ Service Connector through a missing SMD component resistor/diode, and to pin 4 @ PCI Connector | 3.3 | |
80 | P12/EX26/SO00/TxD0 | SO from Cell Slave to Syscon Master | 0 | |
81 | P11 P11/EX25/SI00/RxD0 | SI from Syscon Master to Cell Slave | 1.2 | |
82 | P10/EX24/SCK00 | Serial Clock | 0 | |
83 | P90 | Chip Select | 2.0 | |
84 | P91 | 3v @ standby | 3.0 | |
85 | 0 | |||
86 | 0 | |||
87 | 0 | |||
88 | P95/SCK11/SCL11 | 0 | ||
89 | /SI11/SDA11 | 0 | ||
90 | P97/SO11 | 0 | ||
91 | 0 | |||
92 | Connected to voltage regulator BD3527 (near FLASH), pin 12 | 0 | ||
93 | 0 | |||
94 | 0 | |||
95 | Connected to voltage regulator BD3527 (near USB), pin 12 | 0 | ||
96 | 0 | |||
97 | P101 | Connected to voltage regulator 463A, pin 2 (3.3_EVER_B) | 3v @ standby (3.3) | |
98 | 0 | |||
99 | 0 | |||
100 | P146 | Connected to voltage regulator 463A, pin 2 (3.3_EVER_B) | 3v @ standby (3.3) | |
101 | GROUND | 0 | ||
102 | 0 | |||
103 | 0 | |||
104 | 0 | |||
105 | 0 | |||
106 | 0 | |||
107 | 0 | |||
108 | 0 | |||
109 | P150 | 3v @ standby | 3.0 | |
110 | P27/POW_SW_DET | Power switch detect. Connected to switch board | 3v @ standby (3.3) 3.3 | |
111 | P26/EJECT_SW_DET | Eject switch detect. Connected to switch board | 3v @ standby (3.3) 3.3 | |
112 | 0 | |||
113 | 0 | |||
114 | 0 | |||
115 | 0 | |||
116 | 0 | |||
117 | P20 | (0V?) | 0 | |
118 | P130/ACDC_STBY | Connected to standby voltage regulator 348A, pins 2 and 7 EN_HDMI ? | 3v @ standby (3.3) | |
119 | P102 | 3v @ standby (3.3) | ||
120 | 0 | |||
121 | P04/SCK10/SCL10 | 0 | ||
122 | SI10/RxD1/SDA10 | 0 | ||
123 | P02/SO10/TxD1 | 0 | ||
124 | Connected to pin93 @Panasonic MN8647091 | 0 | ||
125 | 0 | |||
126 | P145/FAN_PWM | PWM Control for the Fan. | 0 | |
127 | P144/SO20/TxD2 | 0 | ||
128 | /SI20/RxD2/SDA20 | Connected to pin29 @Panasonic MN8647091 | 0 |