Switch boards

Power Eject boards

PS3 Series	Power Eject board		Connector (number of pins)	Buttons		Leds (this can be expanded)
	Model	Part Nº		Power	Eject	Power On	Standby	Eject	Others
1000 Series	CSW-001	1-871-871-21	10	Yes	Yes	Yes	Yes	Yes
2000 Series	DSW-001	1-880-056-11	10	Yes	Yes	Yes	Yes	Yes	*See modding section at bottom
	HSW-001	1-881-946-21	10	Yes	Yes	Yes	Yes	Yes	*See modding section at bottom
3000 Series	KSW-001	1-884-751-31	6	Yes	Yes	Yes	No	No
4000 Series	MSW-001	1-886-929-11	6	Yes	No	Yes	No	No

note: boardmodel naming seems thus first letter of SKU motherboard (C=COK / D=DYN / K-KTE / M=MSX/MPX) + "SW-001" (with some exception, like the HSW-001 seen above)

CSW-001

• 

  Power Eject board CSW-001 (PCB top view)

• 

  Power Eject board CSW-001 (PCB bottom view)

DSW-001

• 

  Power Eject board DSW-001 (top view)

• 

  Power Eject board DSW-001 (bottom view)

• 

  Power Eject board DSW-001 (PCB top view)

• 

  Power Eject board DSW-001 (PCB bottom view)

HSW-001

• 

  Power Eject board HSW-001 (top view)

• 

  Power Eject board HSW-001 (PCB with ribbon cable, top view)

• 

  Power Eject board HSW-001 (PCB top view)

• 

  Power Eject board HSW-001 (PCB bottom view)

• 

  Power Eject board HSW-001 (JSD-001) schematic

Pin	Signal	Description
1	N.C.	not connected on motherboard, but on Power Eject board it is sourced to 2 leds via T1 transistor and currentlimitor resistors of 3K and 820 Ω ; see modding section
2	VCC	+5V DC VCC
3	WHITE	connects to 4 white leds with currentlimitor resistor of 1K Ω
4	GND	Ground
5	EJECT	Eject button (sink to ground to activate)
6	POWER	Power button (sink to ground to activate)
7	RED	connects to red led with currentlimitor resistor of 1K2 Ω
8	GREEN	connects to green led with currentlimitor resistor of 1K2 Ω
9	BLUE	connects to blue led with currentlimitor resistor of 560 Ω
10	GND	Ground

KSW-001

• 

  Power Eject board KSW-001 (top view)

• 

  Power Eject board KSW-001 (PCB top view)

• 

  Power Eject board KSW-001 (PCB with ribbon cable, bottom view)

• 

  Power Eject board KSW-001 (PCB bottom view)

MSW-001

• 

  Power Eject board MSW-001 (PCB top view)

• 

  Power Eject board MSW-001 (PCB bottom view)

Flex Ribbon cables

PS3 1000 Series

• 

  Power Eject Flex Ribbon Cable (PS3 1000 series, top view)

• 

  Power Eject Flex Ribbon Cable (PS3 1000 series, bottom view)

PS3 2000 Series

• 

  Power Eject Flex Ribbon Cable (PS3 2000 series, top view)

PS3 3000 Series

• 

  Power Eject Flex Ribbon Cable (PS3 3000 series, top view)

• 

  Power Eject Flex Ribbon Cable (PS3 3000 series, bottom view)

Modding

Enabling the "contour leds" in DSW-001 and HSW-001 power eject boards

Power Eject board PS3 2000 series
Detail of the transparent "light reactive" contour all along the top edge

Power Eject board PS3 2000 series
Detail of the transparent "light reactive" square hole in the corner

Power Eject board PS3 2000 series
Detail of the "mysterious leds" at left corner, and unpopulated components

PS3 2000 series (CECH-20xx, CECH-21xx, and CECH-25xx, with power eject boards DSW-001 and HSW-001) has been designed to have a lighted line all around the top edge of the power eject board

This is clearly visible in the plastic "light reactive" material used in the edge, and the square hole in the corner that allows the light to "transpass" the surface (with a 45 degrees angle bouncing surface at top of the hole that aligns the light rays in paralell to the buttons surface)

Under this square there are 2 leds (placed in opposite directions and diferent type, and another 2 missing leds at this side for a total of 4 leds) that are connected to a group of capacitors, resistors, and transistors (most of them not populated) and to the ribbon cable (that goes to syscon)

Why is this subcircuit present in this power eject boards is a mystery, obviously it was designed to be lighted but at some point somebody declined the idea (maybe poor lighting, maybe too scandalous for sony taste, who knows)... the point is the components are missing, so this leds at the corner are disabled from factory

To re-enable them is not only needed to populate the missing components, is also needed to be sure syscon is sending the correct signal to controll them (we have no idea when are supposed to be lighted). The components missing are easy to identificate because are the same than the others present at his side

There is a manual to "bridge" the traces that goes to this "mysterious" leds with the "standby" or "eject" led in this link http://translate.google.com/translate?sl=fr&tl=en&js=n&prev=_t&hl=es&ie=UTF-8&u=http%3A%2F%2Fps3gunz.org%2Fforum%2Fviewtopic.php%3Fpid%3D590435&act=url

• Notes
  • this mod is not recommended, because the "bridged" line is taking too much current from the new leds, because doesnt even explain what is each line, because the leds are not controlled by syscon as originally was designed
  • He didnt taked care of the "bouncing surface" over the square (barelly visible in the photos) and along the curve... all the "light reactive" surface needs to be covered with a "mirror" sticker to make the light rays to "bounce" first in paralell direction to the surface, and then bounce again along the curve. This sticker doesnt exists (because they decided to disable all this), but for sure it was in the initial design to preserve the lighting