Template:Syscon pinout LQFP 128 pins

From PS3 Developer wiki
Revision as of 04:32, 2 July 2022 by Sandungas (talk | contribs)
Jump to navigation Jump to search


Pinout

Syscon pinout LQFP 128 pins
NEC/Renesas 78K0R/KH3 Optional pin configurations

Syscon SW2-303 unsoldered
CECH-25xx with JTP-001 or JSD-001 motherboard

Syscon SW2-303
CECH-25xx with JTP-001 or JSD-001 motherboard

Syscon SW-301
CECHLxx with VER-001 motherboard
[ View ], [ Discuss ] or [ Edit ]
Syscon pinout LQFP 128 pins
[ View ], [ Discuss ] or [ Edit ]
Pin Port Name Type Description STBY Voltages
NEC/Renesas Sony/Custom
1 14 SCL20 HDMI_I2C_SCL
Out
 Connected to HDMI controller MN8647091 pin 27 0
2 14 INTP7 SB_INT/SYSCSINT
In
 Connected to South Bridge CXD9963GB pad W22 through a resistor ~1V @ standby (0 V?)
3 14 INTP6 BE_INT/ATTENTION
In
 Connected to CELL pad BA17 (1342 pads layout), or pad UNK (1308 pads layout) through a NPN transistor 3V @ standby (3.15V)
4 12 EXLVI
Others
 Connected to +12V_MAIN through a resistor and divider (EXLVI config = External potential input for low-voltage detector ?) 0
5 3 P37 POW_LED
Out
 Connected to Switch board dual led (Green) through a dual digital NPN transistor EMH1(SOT-563) 0
6 3 P36 STBY_LED
Out
 Connected to Switch board dual led (Red) through a dual digital NPN transistor EMH1(SOT-563) 3v @ standby (3.3V)
7 3 P35 ? Connected to South Bridge CXD9963GB pad AA18 (SB_RESET ?, or SB_CGRST ?), see talk page 0
8 3 P34 ? Connected to South Bridge CXD9963GB pad AA17 (SB_RESET ?, or SB_CGRST ?), see talk page 0
9 3 P33 ? CELL BE related? (BE_RESET) 0
10 3 P32 ? 0
11 16 TO13 BACK_LEDS
Out
 Connected to Switch board backlit LEDs through a transistor 0
12 16 TO12 SW_PWM ?
Out
 Connected to Switch board contour LEDs through a transistor 0
13 16 P161/TI11/TO11
Not Connected
 NOT_CONNECTED. Floating through a missing SMD component. See: NOWHERE 0
14 16 P160/TI10/TO10
Not Connected
 NOT_CONNECTED. Floating through a missing SMD component at the other side of the board. See: VIA 0
15 4 P47/INTP2
Out
 Connected to HDMI controller MN8647091 pin 94 0
16 4 TO05 BUZZER
Out
 Connected to the Buzzer through a transistor 0
17 4 SO01
Out
 Connected to South Bridge CXD9963GB ? (SB_SPI_DO) 0
18 4 SI01
In
 Connected to South Bridge CXD9963GB ? (SB_SPI_DI) 3v @ standby
19 4 SCK01
Out
 Connected to South Bridge CXD9963GB ? (SB_SPI_CLK) 0
20 4 P42
Out
 Connected to South Bridge CXD9963GB ? (SB_SPI_CS) 0
21 4 TOOL1 TOOL_CLK
Out
 Connected to Service Connector 3rd Gen. pin 13 (Tool clock) through a missing resistor 3.0
22 4 TOOL0 TOOL_DAT
In/Out
 Connected to Service Connector 3rd Gen. pin 7 (Tool Data) through a missing resistor 0
23 12 P127 ? 0
24 12 SDA21 THR_I2C_SDA
In/Out
 Connected to Temperature Monitors pin 7 (SMBus data) 3v @ standby (3.15)
25 12 SCL21 THR_I2C_SCL
Out
 Connected to Temperature Monitors pin 8 (SMBus clock) 3v @ standby (3.15)
26 RESET RST
In
 Connected to Service Connector 3rd Gen. pin 9 through a missing resistor
Connected to standby voltage regulator Mitsumi 463A pin 3
27 12 XT2 OSCOUT
In
 Connected to a crystal (Subsystem clock). CLK -> 1-2V Amplitude (32.768Khz)
28 12 XT1 OSCIN
In
 Connected to a crystal (Subsystem clock). CLK -> 1-2V Amplitude (32.768Khz)
29 FLMD0 FLASH_MODE
In
 Connected to Service Connector 3rd Gen. pin 8 (Flash programming mode) through a missing resistor 3.33
30 12 X2 XTAL
In
 Connected to a crystal (Main system clock) marked "EX" (16.9344Mhz?) 0.8v @ standby (1.1)
31 12 X1 EXTAL
In
 Connected to a crystal (Main system clock) marked "EX" (16.9344Mhz?) 2.2v @ standby (2.4)
32 REGC VREG_CAP
Others
 Connected to battery+ through 2 diodes
Connected to a capacitor (internal voltage regulator, around 1uF) at the other side of the board. See: VIA
33 VSS0 GND
Others
 0
34 EVSS0 GND
Others
 0
35 VDD 3.3_EVER_B
Others
 Connected to standby voltage regulator Mitsumi 463A pin 2 3v @ standby (3.3)
36 EVDD0 3.3_EVER_B
Others
 Connected to standby voltage regulator Mitsumi 463A pin 2 3v @ standby (3.3)
37 6 SCL0 MK_I2C_SCL
Out
 Connected to Texas Instruments-SCEI Clock Generator CDC972 pin 37 0.2v @ standby
38 6 SDA0 MK_I2C_SDA
In/Out
 Connected to Texas Instruments-SCEI Clock Generator CDC972 pin 38 0.2v @ standby
39 6 P62 ? 0
40 6 P63 P63_DOWN
Others
 10K resistor to GND 0
41 3 INTP4 ACIN_DET
In
 Connected to Power Supply control connector pin 4 through a transistor. See: schematic 3v @ standby (3.3)
42 6 P64/RD
Out
 Connected to voltage regulator BD9684 0906 pin 4 (enable something) through some undocumented components 0
43 6 WR0 ? Connected to Service Connector 3rd Gen. pin 12 through a missing resistor 3.0
44 6 P66/WR1 ? 0
45 6 P67/ASTB
Not Connected
 NOT_CONNECTED. 0
46 7 P77/EX23/KR7/INTP11 ? Connected to CELL pad BA19 ? (1342 pads layout), or pad UNK (1308 pads layout) through a transistor (labeled 26 and located near the CELL temperature monitor)
It seems to be some kind of ALERT signal (inverted direction than the signal from pin 109) BE_POWGOOD ?		 0
47 7 P76/EX22/KR6/INTP10 ? 3v @ standby (3.15)
48 7 INTP9 VD_VINT0/RSX_VINTE0
In
 Connected to RSX pad AR22 (RSX layout 41x41) through a transistor 3v @ standby (3.15)
49 7 P74/EX20/KR4/INTP8 P74_DOWN
Others
 10K resistor to GND 0
50 7 KR3 ? Connected to Service Connector 3rd Gen. pin 3
Connected to voltage regulator D35653 0S25 (FLASH_ENABLE ?)		 0
51 7 P72/EX18/KR2 ? Connected to xxxxxxxxxxxxxx through transistor 0
52 7 P71/EX17/KR1
Out
 Connected to voltage regulator Rohm BD3525 pin 12 (enable something) 0
53 7 P70/EX16/KR0 ? 0
54 0 P06/WAIT P06_DOWN
Others
 45K resistor array to GND 0
55 0 P05/CLKOUT P05_DOWN
Others
 45K resistor array to GND 0
56 EVSS1 GND
Others
 0
57 EVDD1 3.3_EVER_B
Others
 Connected to standby voltage regulator Mitsumi 463A pin 2 3v @ standby (3.3)
58 8 P80/EX0 ? 47k resistor tied to vcc 0
59 8 P81/EX1 ? 47k resistor tied to vcc 0
60 8 P82/EX2 ? 47k resistor tied to vcc 0
61 8 P83/EX3 ? 47k resistor tied to vcc 0
62 8 P84/EX4 ? 47k resistor tied to vcc 0
63 8 P85/EX5 ? 47k resistor tied to vcc 0
64 8 P86/EX6 ? 47k resistor tied to vcc 0
65 8 P87/EX7 ? tied to a resistor of 10k 0
66 3 P30/INTP3/RTC1HZ ? goes to isl 6325 pin 9 0
67 5 P50/EX8 ? goes to isl 6325 pin 8 0
68 5 P51/EX9 ? goes to isl 6325 pin 7 0
69 5 P52/EX10 ? goes to isl 6325 pin 6 0
70 5 P53/EX11 ? goes to isl 6325 pin 5 0
71 5 P54/EX12 ? goes to isl 6325 pin 4 0
72 5 P55/EX13 ? goes to isl 6325 pin 3 0
73 5 P56/EX14 ? goes to isl 6325 pin 2 0
74 5 P57/EX15 ? goes to isl 6325 pin 20 0
75 1 P17/EX31/TI02/TO02 RSX_VDDR_EN
Out
 Connected to RSX through voltage regulator Mitsumi 810X pin 5 0
76 1 INTP5 RSX_INT
In
 Connected to RSX pad AY7 (RSX layout 41x41) through a transistor 3v @ standby (3.15)
77 1 P15/EX29/RTCDIV/RTCCL ? 3v @ standby (3.3)
78 1 RxD3 UART0_RxD
In
 Connected to Service Connector 3rd Gen. pin 11 (UART-TTL terminal Receive) through a missing resistor
Connected to PCI Connector pin 6		 0
79 1 TxD3 UART0_TxD
Out
 Connected to Service Connector 3rd Gen. pin 10 (UART-TTL terminal Transmit) through a missing resistor
Connected to PCI Connector pin 4		 3.3
80 1 SO00 BE_SPI_DO
Out
 Connected to CELL pad AV13 (1342 pads layout), or pad UNK (1308 pads layout). Serial Output from Syscon Master to Cell Slave (MOSI) 0
81 1 SI00 BE_SPI_DI
In
 Connected to CELL pad BA13 (1342 pads layout), or pad UNK (1308 pads layout). Serial Input from Cell Slave to Syscon Master (MISO) 1.2
82 1 SCK00 BE_SPI_CLK
Out
 Connected to CELL pad AY13 (1342 pads layout), or pad UNK (1308 pads layout). 2.5 Mhz SPI Clock
83 9 P90 BE_SPI_CS
Out
 Connected to CELL pad AW13 (1342 pads layout), or pad UNK (1308 pads layout). Chip Select 2.0
84 9 P91/EX33 ? 3v @ standby
85 9 P92/EX34 ? 0
86 9 P93/EX35 ? 0
87 9 P94
Out
 Connected to RSX pad AW8 ? (RSX_SPI_CS). See: Template:RSX pad layout 41x41 and pad AW8 0
88 9 SCK11
Out
 Connected to RSX pad AY8 ? (RSX_SPI_CLK ). See: Template:RSX pad layout 41x41 and pad AY8 0
89 9 SI11
In
 Connected to RSX pad BA7 ? (RSX_SPI_DI). See: Template:RSX pad layout 41x41 and pad BA7 0
90 9 SO11
Out
 Connected to RSX pad BA6 ? (RSX_SPI_DO). See: Template:RSX pad layout 41x41 and pad BA6 0
91 11 P112 ? 0
92 11 P113
Out
 Connected to voltage regulator BD3527 pin 12 (located near FLASH) 0
93 11 P114 ? goes to BD352 ic pin 12 0
94 11 P115 ? Connected to xxxxxxxxxxxxxx through transistor / BD949 pin 5 0
95 11 P116
Out
 Connected to voltage regulator BD3527 pin 12 (located near USB) 0
96 11 P117 AV_EN
Out
 Connected to MultiAV connector pin 3 (+5V output) through a transistor 0
97 AVREF1 3.3_EVER_B
Others
 Connected to standby voltage regulator Mitsumi 463A pin 2 3v @ standby (3.3)
98 11 P110/ANO0
Not Connected
 NOT_CONNECTED. 0
99 11 P111/ANO1
Not Connected
 NOT_CONNECTED. 0
100 AVREF0 3.3_EVER_B
Others
 Connected to standby voltage regulator Mitsumi 463A pin 2 3v @ standby (3.3)
101 AVSS0 GND
Others
 0
102 15 P157/ANI15 P157_DOWN
Others
 100k resistor to GND. And to a missing SMD component to VIA to pin 8 of voltage regulator Mitsumi 463A (3.3_EVER_A) 0
103 15 P156/ANI14 ANI14_UP
Others
 VIA to 100k resistor to pin 8 of voltage regulator Mitsumi 463A (3.3_EVER_A) 0
104 15 P155/ANI13 ANI13_DOWN
Others
 VIA to 100k resistor to GND 0
105 15 P154/ANI12
Not Connected
 100k resistor to GND 0
106 15 P153/ANI11
Not Connected
 100k resistor to GND 0
107 15 P152/ANI10
Not Connected
 on cell front transistor 0
108 15 P151/ANI9
Not Connected
 pass on 100 ohms resistance then to power front panel 0
109 15 P150/ANI8 THERMAL_OVERLOAD ?
In
 Connected to CELL pad AV23 ? (1342 pads layout), or pad UNK (1308 pads layout) through a transistor (labeled ND and located near the CELL temperature monitor)
It seems to be some kind of ALERT signal (inverted direction than the signal from pin 46) BE_POW_FAIL ?
And to 10k resistor to VIA to pin 8 of voltage regulator Mitsumi 463A (3.3_EVER_A)		 3v @ standby
110 2 P27/ANI7 POW_SW
In
 Connected to Switch board power switch 3v @ standby (3.3) 3.3
111 2 P26/ANI6 EJECT_SW
In
 Connected to Switch board eject switch 3v @ standby (3.3) 3.3
112 2 P25/ANI5 ? Connected to Wifi/BT module (BT_WAKEON ? or BT_RESET ?) 0
113 2 P24/ANI4 ? Connected to Wifi/BT module (BT_WAKEON ? or BT_RESET ?) 0
114 2 P23/ANI3 ? to resistance 55 ohms to bdrom pin 11 0
115 2 P22/ANI2
In
 Connected to Bluray Drive 8-pins connector pin 8 through 100ohm resistor (DISC_CHUCK or DISC_OUT8_SW or DISC_OUT12_SW or DISC_IN or DISC_PHOT_LED), and to a testpad, see talk page 0
116 2 P21/ANI1
In
 Connected to Bluray Drive 8-pins connector pin 7 through 100ohm resistor (DISC_CHUCK or DISC_OUT8_SW or DISC_OUT12_SW or DISC_IN or DISC_PHOT_LED), and to a testpad, see talk page 0
117 2 P20/ANI0
In
 Connected to Bluray Drive 8-pins connector pin 6 through 100ohm resistor (DISC_CHUCK or DISC_OUT8_SW or DISC_OUT12_SW or DISC_IN or DISC_PHOT_LED), and to a testpad, see talk page (0V?)
118 13 P130 ACDC_STBY
Out
 Connected to Power Supply control connector pin 3 through a 2K2ohm resistor. See: schematic 3v @ standby (3.3)
119 13 P131/TI06/TO06 HDMI_EN
Out
 Connected to voltage regulator Mitsumi 348A pins 2 and 7
Connected to HDMI connector pin 18 (+5V_ANA ?) through a transistor		 3v @ standby (3.3)
120 0 P07 ? Connected to HDMI controller MN8647091 pin 95 through 3.6K resitor 0
121 0 SCL10 DVE_I2C_SCL
Out
 Connected to Digital Video Encoder CXM4027R pin 35 0
122 0 SDA10 DVE_I2C_SDA
In/Out
 Connected to Digital Video Encoder CXM4027R pin 36 0
123 0 P02 ? to pin 12 bdrom port (DISC_IN or DISC_PHOT_LED ?) 0
124 0 P01/TO00 ? Connected to HDMI controller MN8647091 pin 93 0
125 0 P00/TI00 ? to bottom transistor under optical port 0
126 14 TO07 FANPWM0
Out
 Connected to the FAN grey wire (PWM duty) 0
127 14 P144 ? to pin 17 bdrom port (DISC_IN or DISC_PHOT_LED ?) 0
128 14 SDA20 HDMI_I2C_SDA
In/Out
 Connected to HDMI controller MN8647091 pin 29 0
Retrieved from "http://www.psdevwiki.com/ps3/index.php?title=Template:Syscon_pinout_LQFP_128_pins&oldid=67285"