Syscon Hardware

Syscon 1st Generation (BGA Packaging)

Syscon is the main power controller chip. It is responsible for powering up the various power systems and for configuring and initialising the CELL BE, RSX and South Bridge. It communicates with these devices via seperate SPI busses. There is external access by JTAG (ARM7TDMI which is at factory disabled by blowing a fuse) and Serial.

Serialnumbers @ SKU

SoftID { 065D, 0832, 08A0, 08C2, 0918, 0B8E, 0C16, 0D52, 0DBF, 0E69, 0F29, 0F38 };

Model	Type	Board	Syscon part no.	Soft Id.	Notes
CECHAxx	0x01	COK-001	CXR713120-201GB	0B8E
CECHBxx	0x02	COK-001	CXR713120-201GB	0B8E
CECHCxx	0x03	COK-002	CXR713120-201GB	0C16
CECHDxx	SKU never released
CECHExx	0x04	COK-002   or COK-002W	CXR713120-201GB	0C16
CECHFxx	SKU never released
CECHGxx	0x05	SEM-001	CXR713120-201GB	0D52
CECHHxx	0x06	DIA-001	CXR713120-201GB	0DBF
CECHIxx	SKU never released
CECHJxx	0x07	DIA-002	CXR713120-201GB	0E69
CECHKxx	0x07	DIA-002	CXR713120-201GB	0E69
CECHLxx	0x08	VER-001	SW-301   or SW-302	065D
CECHMxx	0x08	VER-001	SW-301   or SW-302	065D
CECHNxx	SKU never released
CECHOxx	SKU never released
CECHPxx	0x08	VER-001	SW-301   or SW-302	065D
CECHQxx	0x08	VER-001	SW-301   or SW-302	065D
CECH-20xx	0x09	DYN-001	SW2-301	0832
CECH-21xx	0x0A	SUR-001	SW2-301   or SW2-302	08C2
CECH-25xx	0x0B	JTP-001   or JSD-001	SW2-301  or SW2-302	08C2
CECH-30xx	0x0C	KTE-001	SW2-301  or SW2-302	0918
CECH-40xx	?0x0D?	MSX-001	SW3-302

Non-retail

Model	Type	Board	Syscon part no.	Soft Id.	Notes
DECR10xx	0x01	TMU-520	CXR713F120A	03FB	CP Helper Processor CXD9790GG
DEH-H100x	0x01	COK-001	CXR713F120A	0B67
DECHAxx	0x01	COK-001	CXR713120-201GB	0B8E
DECHJxx	0x07	DIA-002	CXR713120-201GB	0E69
DECR14xx	0x09	DEB-001	CXR713120-201GB	0E69
DECH20xx	0x09	DYN-001	SW2-301	0832
DECH25xx	0x0B	JTP-001   or JSD-001	SW2-301  or SW2-302	08C2
DECH30xx	0x0C	KTE-001	SW2-301  or SW2-302	0918
DECH40xx	?0x0D?	MSX-001	SW3-302

Syscon UART

You can attach a 3.3v TTL cable (LV-TTL) to the UART on syscon. There is a simple plaintext protocol involved. This varies on different syscon models. Example:

<command>:<hash>

Where the hash is the sum of command bytes & 0xFF

you should terminate commands with \r\n, the syscon messages are only terminated with \n

Here are some of the commands/messages encountered:

Messages:
Power applied (standby mode)
OK 00000000:3A

Power on
# (PowerOn State):7F

Power off (Hard shutdown)
# (PowerOff State):DD

After Fan test:
# (PowerOff State) (Fatal):36

No text, invalid hash:
NG F0000002:4D

Commands:
VER:ED
OK 00000000 S1E 00 00 065D:A4

ERRLOG:CB
OK 00000000:3A

DATE:1E
NG F0000003:4E

Template:Models