Template:Syscon pinout LQFP 128 pins: Difference between revisions
Jump to navigation
Jump to search
mNo edit summary |
mNo edit summary |
||
| Line 90: | Line 90: | ||
| 39 || P62 || || ←I/O→ || || 0 | | 39 || P62 || || ←I/O→ || || 0 | ||
|- | |- | ||
| 40 || P63 || | | 40 || {{cellcolors|#c0c0c0}} P63 || P63_DOWN || ←I || 10K resistor to GND || 0 | ||
|- | |- | ||
| 41 || {{cellcolors|#ff9933}} <s>P31/TI03/TO03/</s>INTP4 || ACIN_DET || ←I || Connected to pin 4 of the [[Power Supply|PSU]] control connector. See: [[Media:SYSCON_SWx_JTP-001_JSD-001_HSW-001_CN101.jpg|CECH-25xx/SW2/SwitchBoard/PSU schematic]] || 3v @ standby (3.3) | | 41 || {{cellcolors|#ff9933}} <s>P31/TI03/TO03/</s>INTP4 || ACIN_DET || ←I || Connected to pin 4 of the [[Power Supply|PSU]] control connector. See: [[Media:SYSCON_SWx_JTP-001_JSD-001_HSW-001_CN101.jpg|CECH-25xx/SW2/SwitchBoard/PSU schematic]] || 3v @ standby (3.3) | ||
Revision as of 11:02, 26 June 2021
Pinout
| Pin # | Name | Type | Description | STBY Voltages | |
|---|---|---|---|---|---|
| NEC/Renesas | Sony/Custom | ||||
| 1 | P142/SCK20/SCL20 | ←I | Connected to pin27 @Panasonic MN8647091 (HDMI controller CEC data channel related with pins 127 and 128 ?) | 0 | |
| 2 | SB_INT/SYSCSINT | ←I | Connected to pinD1@SB CXD9963GB through the resistor | ~1V @ standby (0 V?) | |
| 3 | BE_INT/ATTENTION | ←I | Connected to pinBA17@BE through the NPN transistor (CELL switches the transistor to connect this pin to GND) | 3V @ standby (3.15V) | |
| 4 | P120/INTP0/EXLVI | ←I/O→ | To +12V_MAIN through the resistor and divider (EXLVI config = External potential input for low-voltage detector ?) | 0 | |
| 5 | P37 | POW_LED | O→ | Connected to dual led(Green) on Switch board through the dual digital NPN trans. EMH1(SOT-563) | 0 |
| 6 | P36 | STBY_LED | O→ | Connected to dual led(Red) on Switch board through the dual digital NPN trans. EMH1(SOT-563) | 3v @ standby (3.3V) |
| 7 | P35 | ←I/O→ | Connected to pinAA18@SB CXD9963GB | 0 | |
| 8 | P34 | ←I/O→ | Connected to pinAA17@SB CXD9963GB | 0 | |
| 9 | P33 | ←I/O→ | CELL BE related? | 0 | |
| 10 | P32 | ←I/O→ | 0 | ||
| 11 | BACK_LEDS | O→ | Connected to Backlit LEDs on Switch board | 0 | |
| 12 | CONTOUR_LEDS | O→ | Connected to CONTOUR LEDs on Switch board | 0 | |
| 13 | NOT_CONNECTED | - | Disconnected to GND through a missing SMD component. See: NOWHERE | 0 | |
| 14 | NOT_CONNECTED | - | Disconnected to GND through a missing SMD component at the other side of the board. See: VIA | 0 | |
| 15 | P47/INTP2 | ←I/O→ | Unknown purpose. The trace goes in the direction of the Wifi/BT module | 0 | |
| 16 | BUZZER | O→ | Connected to the base of a transistor that drives a pin of the buzzer to GND | 0 | |
| 17 | P45/SO01 | ←I/O→ | SB_SPI_DO @CXD9963GB ? | 0 | |
| 18 | P44/SI01 | ←I/O→ | SB_SPI_DI @CXD9963GB ? | 3v @ standby | |
| 19 | P43/SCK01 | ←I/O→ | SB_SPI_CLK @CXD9963GB ? | 0 | |
| 20 | P42/TI04/TO04 | ←I/O→ | SB_SPI_CS @CXD9963GB ? | 0 | |
| 21 | TOOL_CLK | O→ | Tool clock. Connected to Pin 13 @ Service Connector 3rd Gen. through a missing SMD component resistor/diode | 3.0 | |
| 22 | TOOL_DAT | ←I/O→ | Tool Data. Connected to Pin 7 @ Service Connector 3rd Gen. through a missing SMD component resistor/diode | 0 | |
| 23 | P127/SO21 | ←I/O→ | 0 | ||
| 24 | THR_I2C_SDA | ←I/O→ | SMBus data. Connected to pin 7 of CELL/RSX temperature monitors TMP411A/B | 3v @ standby (3.15) | |
| 25 | THR_I2C_SCL | O→ | SMBus clock. Connected to pin 8 of CELL/RSX temperature monitors TMP411A/B | 3v @ standby (3.15) | |
| 26 | RESET | RESET | ←I | Connected to Pin 9 @ Service Connector 3rd Gen. through a missing SMD component resistor/diode. And to standby voltage regulator 463A, pin 3 | |
| 27 | XT_SUB | ←I | Subsystem clock. Connected to a big black crystal. CLK -> 1-2V Amplitude (32.768Khz?) | ||
| 28 | XT_SUB | ←I | Subsystem clock. Connected to a big black crystal. CLK -> 1-2V Amplitude (32.768Khz?) | ||
| 29 | FLMD0 | FLASH_MODE | - | Flash programming mode. Connected to pin 8 @ Service Connector 3rd Gen. through a missing SMD component resistor/diode | 3.33 |
| 30 | XT_MAIN | ←I | Main system clock. Connected to a tiny metallic crystal marked "EX" | 0.8v @ standby (1.1) | |
| 31 | XT_MAIN | ←I | Main system clock. Connected to a tiny metallic crystal marked "EX" | 2.2v @ standby (2.4) | |
| 32 | REGC | VREG_CAP | - | Capacitor for the internal voltage regulator. Connected to ground through a capacitor (around 1uF) at the other side of the board. See: VIA. And 2 diodes to battery+ | |
| 33 | VSS0 | GND | - | 0 | |
| 34 | EVSS0 | GND | - | 0 | |
| 35 | VDD | 3.3_EVER_B | - | Connected to standby voltage regulator 463A, pin 2 | 3v @ standby (3.3) |
| 36 | EVDD0 | 3.3_EVER_B | - | Connected to standby voltage regulator 463A, pin 2 | 3v @ standby (3.3) |
| 37 | P60/SCL0 | ←I/O→ | Primary I2C bus. UNK_I2C_SCL ? (either HDMI, DVE, or MK) | 0.2v @ standby | |
| 38 | P61/SDA0 | ←I/O→ | Primary I2C bus. UNK_I2C_SDA ? (either HDMI, DVE, or MK) | 0.2v @ standby | |
| 39 | P62 | ←I/O→ | 0 | ||
| 40 | P63 | P63_DOWN | ←I | 10K resistor to GND | 0 |
| 41 | ACIN_DET | ←I | Connected to pin 4 of the PSU control connector. See: CECH-25xx/SW2/SwitchBoard/PSU schematic | 3v @ standby (3.3) | |
| 42 | P64/RD | ←I/O→ | Connected (indirectly) to voltage regulator BD9684 0906, pin 4 (enable something) | 0 | |
| 43 | P65/WR0 | ←I/O→ | Connected to Pin 12 @ Service Connector 3rd Gen. through a missing SMD component resistor/diode | 3.0 | |
| 44 | P66/WR1 | ←I/O→ | 0 | ||
| 45 | NOT_CONNECTED | - | 0 | ||
| 46 | P77/EX23/KR7/INTP11 | ←I/O→ | 0 | ||
| 47 | P76/EX22/KR6/INTP10 | ←I/O→ | 3v @ standby (3.15) | ||
| 48 | P75/EX21/KR5/INTP9 | ←I/O→ | 3v @ standby (3.15) | ||
| 49 | P74/EX20/KR4/INTP8 | ←I/O→ | 0 | ||
| 50 | P73/EX19/KR3 | ←I/O→ | Connected to pin 3 @ Service Connector 3rd Gen.. And to voltage regulator D35653 0S25 (FLASH_ENABLE ?) | 0 | |
| 51 | P72/EX18/KR2 | ←I/O→ | 0 | ||
| 52 | P71/EX17/KR1 | ←I/O→ | Connected to voltage regulator BD3525, pin 12 (enable something) | 0 | |
| 53 | P70/EX16/KR0 | ←I/O→ | 0 | ||
| 54 | P06/WAIT | ←I/O→ | 0 | ||
| 55 | P05/CLKOUT | ←I/O→ | 0 | ||
| 56 | EVSS1 | GND | - | 0 | |
| 57 | EVDD1 | 3.3_EVER_B | - | Connected to standby voltage regulator 463A, pin 2 | 3v @ standby (3.3) |
| 58 | P80/EX0 | ←I/O→ | 0 | ||
| 59 | P81/EX1 | ←I/O→ | 0 | ||
| 60 | P82/EX2 | ←I/O→ | 0 | ||
| 61 | P83/EX3 | ←I/O→ | 0 | ||
| 62 | P84/EX4 | ←I/O→ | 0 | ||
| 63 | P85/EX5 | ←I/O→ | 0 | ||
| 64 | P86/EX6 | ←I/O→ | 0 | ||
| 65 | P87/EX7 | ←I/O→ | 0 | ||
| 66 | P30/INTP3/RTC1HZ | ←I/O→ | 0 | ||
| 67 | P50/EX8 | ←I/O→ | 0 | ||
| 68 | P51/EX9 | ←I/O→ | 0 | ||
| 69 | P52/EX10 | ←I/O→ | 0 | ||
| 70 | P53/EX11 | ←I/O→ | 0 | ||
| 71 | P54/EX12 | ←I/O→ | 0 | ||
| 72 | P55/EX13 | ←I/O→ | 0 | ||
| 73 | P56/EX14 | ←I/O→ | 0 | ||
| 74 | P57/EX15 | ←I/O→ | 0 | ||
| 75 | P17/EX31/TI02/TO02 | ←I/O→ | Connected to voltage regulator Mitsumi 040 810X, pin 5 | 0 | |
| 76 | P16/EX30/TI01/TO01/INTP5 | ←I/O→ | 3v @ standby (3.15) | ||
| 77 | P15/EX29/RTCDIV/RTCCL | ←I/O→ | 3v @ standby (3.3) | ||
| 78 | SC_RxD | ←I | SC_RxD UART (terminal).Connected to Pin 11 @ Service Connector 3rd Gen. through a missing SMD component resistor/diode, and to pin 6 @ PCI Connector | 0 | |
| 79 | SC_TxD | O→ | SC_TxD UART (terminal).Connected to Pin 10 @ Service Connector 3rd Gen. through a missing SMD component resistor/diode, and to pin 4 @ PCI Connector | 3.3 | |
| 80 | BE_SPI_DO | O→ | SO from Cell Slave to Syscon Master | 0 | |
| 81 | BE_SPI_DI | ←I | SI from Syscon Master to Cell Slave | 1.2 | |
| 82 | BE_SPI_CLK ? | ←I/O→ | Serial Clock | 0 | |
| 83 | P90/EX32 | BE_SPI_CS ? | ←I/O→ | Chip Select | 2.0 |
| 84 | P91/EX33 | ←I/O→ | 3v @ standby | ||
| 85 | P92/EX34 | ←I/O→ | 0 | ||
| 86 | P93/EX35 | ←I/O→ | 0 | ||
| 87 | P94 | ←I/O→ | RSX_SPI_CS ? See: Template:RSX pad layout 41x41 and pad AW8@ | 0 | |
| 88 | P95/SCK11/SCL11 | ←I/O→ | RSX_SPI_CLK ? See: Template:RSX pad layout 41x41 and pad AY8@ | 0 | |
| 89 | P96/SI11/SDA11 | ←I/O→ | RSX_SPI_DI ? See: Template:RSX pad layout 41x41 and pad BA7@ | 0 | |
| 90 | P97/SO11 | ←I/O→ | RSX_SPI_DO ? See: Template:RSX pad layout 41x41 and pad BA6@ | 0 | |
| 91 | P112 | ←I/O→ | 0 | ||
| 92 | P113 | ←I/O→ | Connected to voltage regulator BD3527 (near FLASH), pin 12 | 0 | |
| 93 | P114 | ←I/O→ | 0 | ||
| 94 | P115 | ←I/O→ | 0 | ||
| 95 | P116 | ←I/O→ | Connected to voltage regulator BD3527 (near USB), pin 12 | 0 | |
| 96 | P117 | ←I/O→ | 0 | ||
| 97 | AVREF1 | 3.3_EVER_B | - | Connected to standby voltage regulator 463A, pin 2 | 3v @ standby (3.3) |
| 98 | NOT_CONNECTED | - | 0 | ||
| 99 | NOT_CONNECTED | - | 0 | ||
| 100 | AVREF0 | 3.3_EVER_B | - | Connected to standby voltage regulator 463A, pin 2 | 3v @ standby (3.3) |
| 101 | AVSS0 | GND | - | 0 | |
| 102 | ANI15_DOWN | ←I | 100k resistor to GND. And to a missing SMD component to VIA to pin 8 of voltage regulator 463A (3.3_EVER_A) | 0 | |
| 103 | ANI14_UP | ←I | VIA to 100k resistor to pin 8 of voltage regulator 463A (3.3_EVER_A) | 0 | |
| 104 | ANI13_DOWN | ←I | VIA to 100k resistor to GND | 0 | |
| 105 | NOT_CONNECTED | - | 0 | ||
| 106 | NOT_CONNECTED | - | 0 | ||
| 107 | NOT_CONNECTED | - | 0 | ||
| 108 | NOT_CONNECTED | - | 0 | ||
| 109 | ANI8_UP_UNK | ←I | Connected to an unknown track. And to 10k resistor to VIA to pin 8 of voltage regulator 463A (3.3_EVER_A) | 3v @ standby | |
| 110 | POW_SW_DET | ←I | Power switch detect. Connected to Switch board | 3v @ standby (3.3) 3.3 | |
| 111 | EJECT_SW_DET | ←I | Eject switch detect. Connected to Switch board | 3v @ standby (3.3) 3.3 | |
| 112 | P25/ANI5 | ←I/O→ | Connected to Wifi/BT module, unknown pad | 0 | |
| 113 | P24/ANI4 | ←I/O→ | Connected to Wifi/BT module, unknown pad | 0 | |
| 114 | P23/ANI3 | ←I/O→ | 0 | ||
| 115 | P22/ANI2 | ←I/O→ | 0 | ||
| 116 | P21/ANI1 | ←I/O→ | 0 | ||
| 117 | P20/ANI0 | ←I/O→ | (0V?) | ||
| 118 | P130 | ACDC_STBY | O→ | Connected to pin 3 of the PSU control connector. See: CECH-25xx/SW2/SwitchBoard/PSU schematic | 3v @ standby (3.3) |
| 119 | P131/TI06/TO06 | ←I/O→ | Connected to voltage regulator 348A, pins 2 and 7 (EN_HDMI & EN_AV together ?... in other words, enable video output) | 3v @ standby (3.3) | |
| 120 | P07 | ←I/O→ | 0 | ||
| 121 | P04/SCK10/SCL10 | ←I/O→ | 0 | ||
| 122 | P03/SI10/RxD1/SDA10 | ←I/O→ | 0 | ||
| 123 | P02/SO10/TxD1 | ←I/O→ | 0 | ||
| 124 | P01/TO00 | ←I/O→ | Connected to pin93 @Panasonic MN8647091 | 0 | |
| 125 | P00/TI00 | ←I/O→ | 0 | ||
| 126 | FAN_PWM | O→ | PWM Control for the Fan. | 0 | |
| 127 | P144/SO20/TxD2 | ←I/O→ | (HDMI controller CEC data channel related with pins 1 and 128 ?) | 0 | |
| 128 | P143/SI20/RxD2/SDA20 | ←I/O→ | Connected to pin29 @Panasonic MN8647091 (HDMI controller CEC data channel related with pins 1 and 127 ?) | 0 | |
