Talk:Syscon Hardware: Difference between revisions
| Line 93: | Line 93: | ||
'''Talk''' | '''Talk''' | ||
-This breaks lot of standards/pages/tables in ps3devwiki, can you add some notes please ?. E.g: the board came from official repair service, bought in a normal shop, or is a frankenstein made at home ?, it boots correctly and allows firmware updates ?. If it works normally i think this proves CXR713120-20xGB and CXR714120-30xGB shares the same pinout, but the fact that is using 0DBF SoftID is a bit shocking (maybe because is the minimal SoftID allowed by CXR714120-30xGB... [[Talk:More_System_Information | check SoftID examples in this table]]) --[[User:Sandungas|Sandungas]] 22:07, 24 July 2013 (MSK) | -This breaks lot of standards/pages/tables in ps3devwiki, can you add some notes please ?. E.g: the board came from official repair service, bought in a normal shop, or is a frankenstein made at home ?, it boots correctly and allows firmware updates ?. If it works normally i think this proves CXR713120-20xGB and CXR714120-30xGB shares the same pinout, but the fact that is using 0DBF SoftID is a bit shocking (maybe because is the minimal SoftID allowed by CXR714120-30xGB ?... [[Talk:More_System_Information | check SoftID examples in this table]]) --[[User:Sandungas|Sandungas]] 22:07, 24 July 2013 (MSK) | ||
Revision as of 19:12, 24 July 2013
Multipage Correction
<TizzyT> eussnl my syscon is CXR714120-301GB its different form what the wiki says CECHH / DIA-001
Package
http://pastie.org/private/tkcfjwit37huzyzoie7z5g BGA
ball count: 4x16 + 8x14 + 2x12 = 64+112+24 = 200 pads
new QF package is 26 * 38 = 128 pins
Clocks
SysCon clocks:
T4 XTAL / T5 EXTAL goes to [X4001] of 16.9344 MHz C16 OSCIN / B16 OSCOUT goes to [X4002] of 32.768 kHz
http://oi52.tinypic.com/2s9ziw0.jpg
Backup Mode / Diag
BACKUP_MODE / DIAG_MODE pins on Gen 2 might be pins 110 and 111. They are pulled low. Not completely sure, but looking at those pins in relation to what's around them seems like it could be those two.
SEM-001 CECHG
Pink is N15 BACKUP_MODE Blue is N16 DIAG_MODE
picture: http://psx-scene.com/forums/attachments/f149/26456d1300550098-brick-recovery-research-untitled-1.jpg source: http://psx-scene.com/forums/780185-post344.html !unverified!
According to schematics, DIAG and BACKUP_MODE are are shown in the following picture for COK-001 and COK-002 Motherboards - http://goput.it/69k.jpg These pins are tied to 3.3v so grounding them should enable each mode respectively. !unverified!
SoftID
Note: moved from seperate page, as there are already over 8 different syscon pages and the very same info is mention in depth on the SC firmware and SC hardware page (and in 150 wiki edits on the sysinfo page :/) we dont have a sperate page for every SELF flag either ;) (although there are >4 pages describing SELF :/)
a SoftID is just a 0x4 code that tells you the hardware revision of the syscon.
This info can be get through the More System Information method.
You can find them also inside the SYS_CON_FIRMWARE_*********.pkg (Syscon_Firmware) at the offset 0x28E (In this link you can found the list of the Syscon update packages)
every SoftID is associated with the ps3 mainboard. this means that you can know if a SC is compatible with your board without opening a PS3 ( Syscon Hardware)
| SoftID | SC Generation | notes | |
|---|---|---|---|
| Phats | |||
| 0B8E | 1 | - | |
| 0C16 | 2 | - | |
| 0D52 | 3 | - | |
| 0DBF | 4 | - | |
| 0E69 | 5 | - | |
| 0F29 | 6 | - | |
| 0F38 | 7 | - | |
| 065D | 8 | - | |
| Slims | |||
| 0832 | 9 | - | |
| 08C2 | 10 | - | |
| 0918 | 11 | - | |
Datasheet of SoC similar to syscon
COK-002 with 0DBF syscon
Information: https://lh5.googleusercontent.com/-UiaHRjhdt50/UesKSGuxdFI/AAAAAAAAGOU/0FV8Fazyl60/s800/TV2013072019053700.jpg
Board type: https://lh6.googleusercontent.com/-K1sc66WzJxo/Ue1Mdr5mHeI/AAAAAAAAGO8/rnqlidQAVfY/s800/DSC01591.JPG
Syscon: https://lh6.googleusercontent.com/-OTxjx3qJV0M/Ue1L2itOfRI/AAAAAAAAGO0/Bv6zli_xQQg/s800/DSC01590.JPG
Talk
-This breaks lot of standards/pages/tables in ps3devwiki, can you add some notes please ?. E.g: the board came from official repair service, bought in a normal shop, or is a frankenstein made at home ?, it boots correctly and allows firmware updates ?. If it works normally i think this proves CXR713120-20xGB and CXR714120-30xGB shares the same pinout, but the fact that is using 0DBF SoftID is a bit shocking (maybe because is the minimal SoftID allowed by CXR714120-30xGB ?... check SoftID examples in this table) --Sandungas 22:07, 24 July 2013 (MSK)