Template:Syscon pinout LQFP 100 pins

From PS3 Developer wiki
Revision as of 09:55, 1 July 2022 by Sandungas (talk | contribs) (Please zeco review this edit, as far i understand in vyktor images. Syscon pin 7 <---> BD controller pin 7)
Jump to navigation Jump to search


Pinout

Syscon pinout LQFP 100 pins
NEC/Renesas 78K0R/KG3 Optional pin configurations

Syscon SW3-304
CECH-42xx with PQX-001 motherboard
[ View ], [ Discuss ] or [ Edit ]
Syscon pinout LQFP 100 pins
[ View ], [ Discuss ] or [ Edit ]
Pin Port Name Type Description Voltages
NEC/Renesas Sony/Custom Stby Runn
1 14 SCL20 HDMI_I2C_SCL
Out
 Connected to HDMI controller MN8647091 pin 27 0 3.3V
2 14 P141/PCLBUZ1/INTP7 ? Connected to South Bridge CXD9963GB pad AA17 (SB_RESET ?, or SB_CGRST ?)
3 14 INTP6 SB_INT ? Connected to South Bridge CXD9963GB pad W22 3.3V
4 12 EXLVI
In
 Connected to Power Supply main +12V rail through a resistor and divider. Related with Error Code 3001 ? 1.5V
5 4 P47/INTP2 ? Connected to HDMI controller MN8647091 pin 94
6 4 TO05 BUZZER
Out
 Connected to Buzzer- through a NPN 50V@100mA transistor 3.3V
7 4 P45/SO01 ? Connected to bdrom IC pin 11 pin 7 ? (Bluray Drive controller CXD5132R-1 ? or...) 3.3V
8 4 P44/SI01 THR_I2C_SDA
In/Out
 Connected to TMP411A pin 7 through a 47ohm resistor (CELL Temperature Monitor, data)
Connected to TMP411B pin 7 through a 47ohm resistor (RSX Temperature Monitor, data)
Connected to ISL6331 pin 22 (Unknown Temperature sensor, data). And a testpad		 3.3V 3.3V
9 4 P43/SCK01 THR_I2C_SCL
Out
 Connected to TMP411A pin 8 (CELL Temperature Monitor, clock)
Connected to TMP411B pin 8 (RSX Temperature Monitor, clock)
Connected to ISL6331 pin 23 (Unknown Temperature sensor, clock). And a testpad		 3.3V 3.3V
10 4 P42/TI04/TO04 ? Connected to South Bridge CXD9963GB pad AA18 (SB_RESET ?, or SB_CGRST ?) 3.3V
11 4 TOOL1 TOOL_CLK
Out
 Connected to Service Connector 3rd Gen. pin 13 (Tool clock) through a missing resistor 3.3V
12 4 TOOL0 TOOL_DAT
In/Out
 Connected to Service Connector 3rd Gen. pin 7 (Tool Data) through a missing resistor 3.3V
13 RESET RST
In
 Connected to Service Connector 3rd Gen. pin 9 through a missing resistor 3.3V
14 12 XT2 OSCOUT
Out
 Connected to Crystal 32.768kHz (Subsystem clock) 1.2V 1.2V
15 12 XT1 OSCIN
In
 Connected to Crystal 32.768kHz (Subsystem clock) 0.8V
16 FLMD0 FLASH_MODE
In
 Connected to Service Connector 3rd Gen. pin 8 (Flash programming mode) through a missing resistor 3.3V 3.3V
17 12 X2 XTAL
Out
 Connected to Crystal marked "ED" or "EU" (Main system clock)
18 12 X1 EXTAL
In
 Connected to Crystal marked "ED" or "EU" (Main system clock)
19 REGC VDDbat
Others
 Connected to CR2025 battery + through 2 inverted Schottky 30V@30mA diodes ?
1uF capacitor to ground ?		 2.5V
20 VSS GND
Others
21 EVSS0 GND
Others
22 VDD 3.3_EVER_B
Others
 Connected to Mitsumi 463A pin 2 (standby voltage regulator, secondary output power rail) 3.3V 3.3V
23 EVDD0 3.3_EVER_B
Others
 Connected to Mitsumi 463A pin 2 (standby voltage regulator, secondary output power rail) 3.3V 3.3V
24 6 P60/SCL0 ?
25 6 P61/SDA0 ?
26 6 P62 ? Connected to ISL IC pin 3 2.5V
27 6 P63 ? Connected to Switch board dual led (Red) through a dual digital NPN transistor EMH1(SOT-563) ? (STBY_LED ?) 3.3V
28 3 P31/TI03/TO03/INTP4 ACIN_DET ? ? pin 4 to wifi5v vreg ic/EN ?
29 6 P64 ? Connected (indirectly) to a voltage regulator ? (to enable something ?) 3.3V
30 6 P65 ? Connected to IDT4227 pin 1 3.3V
31 6 P66 MK_I2C_SCL ? ? Connected to Texas Instruments-SCEI Clock Generator CDC750 pin 33 3.3V
32 6 P67 MK_I2C_SDA ? ? Connected to Texas Instruments-SCEI Clock Generator CDC750 pin 34 3.3V
33 7 P77/KR7/INTP11 ? Connected to voltage regulator Rohm BD3527 pin 12 (enable USB ?) 3.3V
34 7 P76/KR6/INTP10 ? Connected to ISL6331 pin 24 3.3V
35 7 P75/KR5/INTP9 ? Connected to South Bridge CXD9963GB pad U19 throught 4k7 resistor 3.3V
36 7 P74/KR4/INTP8 ? Connected to ISL6331 pin 20 3.3V
37 7 P73/KR3 ? Connected to Service Connector 3rd Gen. pin 3
Connected to D35236SK pin 6 		3.3V
38 7 P72/KR2 ? Connected to D35326SK pin 7 3.3V
39 7 P71/KR1
Out
 Connected to voltage regulator Rohm BD3525 pin 12 (enable something) 3.3V
40 7 P70/KR0 ? Connected to Texas Instruments PS53123 pin 10 3.3V
41 0 P06 ? Connected to Texas Instruments PS53123 pin 7
42 0 P05 ? Connected to Texas Instruments PS53123 pin 17 3.3V
43 EVSS1 GND
Others
44 8 P80
Others
 Connected to 3v3 through a 100K resistor, and to a unpopulated pad
45 8 P81
Others
 Connected to GND through a 0ohm resistor, and to a unpopulated pad
46 8 P82 ? Connected to HDMI controller MN8647091 pin 95. Notes 3.3V
47 8 P83
Others
 Connected to GND through a 0ohm resistor, and to a unpopulated pad
48 8 P84 ? Connected to pin1 EN vreg 8D11 (bottom side of power pcb) 3.3V
49 8 P85 ? Connected to Texas Instruments PS53123 pin 3 3.3V
50 8 P86 ? Connected to IDT4227 pin 12 3.3V
51 8 P87 ? Connected to power pcb connector 3.3V
52 3 P30/INTP3/RTC1HZ ? Connected to ISL6331 pin 21 3.3V
53 EVDD1 3.3_EVER_B
Others
 Connected to Mitsumi 463A pin 2 (standby voltage regulator, secondary output power rail) 3.3V 3.3V
54 5 P50 ? Connected to ISL6331 pin 25 3.3V
55 5 P51 ? Connected to South Bridge CXD9963GB pad W21. And in line 10k to gnd
56 5 P52 WIFI_CTRL ? 10k resistor to GND, and to wifi/BT module. See: wifi/BT 10x7 pinout or wifi/BT 9x7 pinout Vary 3.3V
57 5 P53 UART0_RxD
In
 Connected to Service Connector 3rd Gen. pin 11 (UART-TTL terminal Receive) through a missing resistor
Connected to PCI Connector pin 6 through a missing resistor
58 5 P54 UART0_TxD
Out
 Connected to Service Connector 3rd Gen. pin 10 (UART-TTL terminal Transmit) through a missing resistor
Connected to PCI Connector pin 4 through a missing resistor		 Vary 3.3V
59 5 P55 ? Connected to South Bridge CXD9963GB pad V19 3.3V
60 5 P56 ? Connected to South Bridge CXD9963GB pad V22. And in line 47ohms 3.3V
61 5 P57 ? Connected to South Bridge CXD9963GB pad U18 3.3V
62 1 P17 RSX_VINTE0
VD_VINT0
In
 Connected to RSX pad AR22 (41x41 layout), or pad UNK (34x34 layout) through a 10k resistor 1.5V
63 1 P16 RSX_CGRST
Not Connected
 Connected to RSX pad AV6 (41x41 layout), or pad UNK (34x34 layout)
This pin is "nerfed" with a 10k resistor to GND in RSX41x41 pad AV6 so syscon is not able to RESET the RSX CG		 0.8V
64 1 P15 RSX_VINTE1
VD_VINT1
In
 Connected to RSX pad AL38 (41x41 layout), or pad UNK (34x34 layout) 1.5V
65 1 P14 RSX_RESET
Out
 Connected to RSX pad AW5 (41x41 layout), or pad UNK (34x34 layout) 1.5V
66 1 P13 RSX_SPI_CS
Out
 Connected to RSX pad AW8 (41x41 layout), or pad UNK (34x34 layout) 1.5V
67 1 SO00 RSX_SPI_DO
Out
 Connected to RSX pad AY8 (41x41 layout), or pad UNK (34x34 layout) 1.5V
68 1 SI00 RSX_SPI_DI
In
 Connected to RSX pad BA7 (41x41 layout), or pad UNK (34x34 layout)
69 1 SCK00 RSX_SPI_CLK
Out
 Connected to RSX pad BA6 (41x41 layout), or pad UNK (34x34 layout)
70 AVREF1
Others
 1.5V
71 11 P110/ANO0 ? Connected to a testpad near SC
72 11 P111/ANO1 RSX_INT
In
 Connected to RSX pad AY7 (41x41 layout), or pad UNK (34x34 layout). Related with Error Code 1802 1.5V
73 AVREF0
Others
 1.2V
74 AVSS GND
Others
75 15 P157 BE_POWGOOD
POWER_GOOD
Out
 Connected to CELL pad UNK (1308 layout), or pad UNK (1359 layout)
Connected to CELL Service Connector CN1001 pad 9		 1.2V
76 15 P156 BE_RESET
BE_RESET_AND
HARD_RESET
Out
 Connected to CELL pad UNK (1308 layout), or pad UNK (1359 layout)
Connected to CELL Service Connector CN1001 pad 6 and 8		 1.2V
77 15 P155 BE_SPI_DO
Out
 Connected to CELL pad UNK (1308 layout), or pad UNK (1359 layout). Serial Output from Syscon Master to Cell Slave
78 15 P154 BE_SPI_DI
In
 Connected to CELL pad UNK (1308 layout), or pad UNK (1359 layout). Serial Input from Cell Slave to Syscon Master
79 15 P153 BE_SPI_CLK
Out
 Connected to CELL pad UNK (1308 layout), or pad UNK (1359 layout). 2.5 Mhz SPI Clock 1.2V
80 15 P152 BE_SPI_CS
Out
 Connected to CELL pad UNK (1308 layout), or pad UNK (1359 layout). Chip Select Vary 1.2V
81 15 P151 BE_INT
ATTENTION
In
 Connected to CELL pad UNK (1308 layout), or pad UNK (1359 layout) through a NPN 50V@100mA transistor. Related with Error Code 1701
82 15 P150 SYS_THR_ALRT
THERMAL_OVERLOAD
In
 Connected to CELL pad UNK (1308 layout), or pad UNK (1359 layout) through a NPN 50V@100mA transistor. Related with Error Code 1103 ?, or 1200 ?
Connected to a testpad		 Vary
83 2 P27/ANI7 ? Connected to Switch board power switch ? (POW_SW?) 3.3V 3.3V
84 2 P26/ANI6 ? Connected to Switch board eject switch ? (EJECT_SW?). And to a testpad
85 2 P25/ANI5 ? 10K resistor to GND, to testpad, and to 100ohms resistor to Wifi/BT module. (BT_WAKEON ? or BT_RESET ?) See: wifi/BT 10x7 pinout or wifi/BT 9x7 pinout
86 2 P24/ANI4 ? 10K resistor to GND, to testpad, and to 100ohms resistor to Wifi/BT module. (BT_WAKEON ? or BT_RESET ?) See: wifi/BT 10x7 pinout or wifi/BT 9x7 pinout
87 2 P23/ANI3 ? 3.3V
88 2 P22/ANI2 ? Connected to Bluray Drive 8-pins connector pin 8 through 100ohm resistor (DISC_CHUCK or DISC_OUT8_SW or DISC_OUT12_SW or DISC_IN or DISC_PHOT_LED), and to a testpad ?. See: pin 115
89 2 P21/ANI1 ? Connected to Bluray Drive 8-pins connector pin 7 through 100ohm resistor (DISC_CHUCK or DISC_OUT8_SW or DISC_OUT12_SW or DISC_IN or DISC_PHOT_LED), and to a testpad ?. See: pin 116 3.3V
90 2 P20/ANI0 ? Connected to Bluray Drive 8-pins connector pin 6 through 100ohm resistor (DISC_CHUCK or DISC_OUT8_SW or DISC_OUT12_SW or DISC_IN or DISC_PHOT_LED), and to a testpad ?. See: pin 117 3.3V 3.3V
91 13 P130 ACDC_STBY ?
Out
 Enable PSU 12v power rail ? 3.3V
92 13 P131/TI06/TO06 ? Connected to voltage regulator Mitsumi 348A pins 2 and 7 ?
Connected to HDMI connector pin 18 (+5V output) through a transistor ?		 3.3V
93 0 SCL10 DVE_I2C_SCL
Out
 Connected to Digital Video Encoder CXM4027R pin 35 3.3V
94 0 SDA10 DVE_I2C_SDA
In/Out
 Connected to Digital Video Encoder CXM4027R pin 36 3.3V
95 0 P02/SO10/TxD1 ? to pin 12 bdrom port ? (DISC_IN or DISC_PHOT_LED ?) 3.3V
96 0 P01/TO00 ? Connected to HDMI controller MN8647091 pin 93 ??? 1.5V
97 0 P00/TI00 ?
98 14 TO07 FANPWM0
Out
 Connected to the FAN grey wire (PWM duty) 0.8V
99 14 P144/SO20/TxD2 ? to pin 17 on bdrom port ? (DISC_IN or DISC_PHOT_LED ?) 3.3V
100 14 SDA20 HDMI_I2C_SDA
In/Out
 Connected to HDMI controller MN8647091 pin 29 0
Retrieved from "http://www.psdevwiki.com/ps3/index.php?title=Template:Syscon_pinout_LQFP_100_pins&oldid=67276"