Template:CSW-001 pinout: Difference between revisions
Jump to navigation
Jump to search
No edit summary |
(Moved from Template:Syscon_pinout_BGA_200_pads) |
||
| Line 9: | Line 9: | ||
| 2 || {{cellcolors|darkgrey|white}} SW_PWM || [[Template:Syscon_pinout_BGA_200_pads|Syscon]] pad N9 || Testpad ? || FREQ. Intended to send a [https://en.wikipedia.org/wiki/Pulse-width_modulation PWM] signal to the switch board ? | | 2 || {{cellcolors|darkgrey|white}} SW_PWM || [[Template:Syscon_pinout_BGA_200_pads|Syscon]] pad N9 || Testpad ? || FREQ. Intended to send a [https://en.wikipedia.org/wiki/Pulse-width_modulation PWM] signal to the switch board ? | ||
|- | |- | ||
| 3 || {{cellcolors|#44cc44|white}} RMC_IN || [[Template:Syscon_pinout_BGA_200_pads|Syscon]] pad R10<br>[[Service Connectors#CN4009|Service Connector]] (CN4009) pin 17 || Testpad ?. <abbr title="missing resistor>NC</abbr> || IR | | 3 || {{cellcolors|#44cc44|white}} RMC_IN || [[Template:Syscon_pinout_BGA_200_pads|Syscon]] pad R10<br>[[Service Connectors#CN4009|Service Connector]] (CN4009) pin 17 || Testpad ?. <abbr title="missing resistor>NC</abbr> || '''R'''e'''M'''ote '''C'''ontrol '''IN'''put<br>The IR receiver component is missing in the Switch board but existed in some PS3 prototypes that was using [https://www.sbprojects.net/knowledge/ir/sirc.php SIRC protocol] and [[SC_Communication#Syscon_Services|SERV_SIRCS]] | ||
|- | |- | ||
| 4 || POW_SW || [[Template:Syscon_pinout_BGA_200_pads|Syscon]] pad B12 || Power Switch {{buttonpower}} || | | 4 || POW_SW || [[Template:Syscon_pinout_BGA_200_pads|Syscon]] pad B12 || Power Switch {{buttonpower}} || | ||
Latest revision as of 04:56, 18 October 2022
| Pin | Name | Connected to | Description | |
|---|---|---|---|---|
| On Motherboard | On Switch board | |||
| 1 | GND | GND | GND | Ground |
| 2 | SW_PWM | Syscon pad N9 | Testpad ? | FREQ. Intended to send a PWM signal to the switch board ? |
| 3 | RMC_IN | Syscon pad R10 Service Connector (CN4009) pin 17 |
Testpad ?. NC | ReMote Control INput The IR receiver component is missing in the Switch board but existed in some PS3 prototypes that was using SIRC protocol and SERV_SIRCS |
| 4 | POW_SW | Syscon pad B12 | Power Switch  |
|
| 5 | EJECT_SW | Syscon pad A12 | Eject Switch  |
|
| 6 | POW_LED | Syscon pad M7 | Green led | |
| 7 | STBY_LED | Syscon pad N7 | Red led | |
| 8 | BD_LED | BluRay connector (CN3221) pin 50 | Blue led | |
| 9 | GND | GND | GND | Ground |
| 10 | +5V_EVER | Power Supply connector (CN6005) pins 4 and 5 | VCC | 5V Standby |