Template:CSW-001 pinout: Difference between revisions

From PS3 Developer wiki
Jump to navigation Jump to search
mNo edit summary
 
(2 intermediate revisions by the same user not shown)
Line 7: Line 7:
| 1 || {{cellcolors|#333333|white}} GND || GND || GND || Ground
| 1 || {{cellcolors|#333333|white}} GND || GND || GND || Ground
|-
|-
| 2 || {{cellcolors|darkgrey|white}} SW_PWM || [[Template:Syscon_pinout_BGA_200_pads|Syscon Mullion]], pad N9 || Testpad ? || FREQ. Intended to send a [https://en.wikipedia.org/wiki/Pulse-width_modulation PWM] signal to the switch board ?
| 2 || {{cellcolors|darkgrey|white}} SW_PWM || [[Template:Syscon_pinout_BGA_200_pads|Syscon]] pad N9 || Testpad ? || FREQ. Intended to send a [https://en.wikipedia.org/wiki/Pulse-width_modulation PWM] signal to the switch board ?
|-
|-
| 3 || {{cellcolors|#44cc44|white}} RMC_IN || [[Template:Syscon_pinout_BGA_200_pads|Syscon Mullion]], pad R10<br>[[Service Connectors#CN4009|Service Connector]] (CN4009) pin 17 || Testpad ?. <abbr title="missing resistor>NC</abbr> || IR Remote Control (input)
| 3 || {{cellcolors|#44cc44|white}} RMC_IN || [[Template:Syscon_pinout_BGA_200_pads|Syscon]] pad R10<br>[[Service Connectors#CN4009|Service Connector]] (CN4009) pin 17 || Testpad ?. <abbr title="missing resistor>NC</abbr> || '''R'''e'''M'''ote '''C'''ontrol '''IN'''put<br>The IR receiver component is missing in the Switch board but existed in some PS3 prototypes that was using [https://www.sbprojects.net/knowledge/ir/sirc.php SIRC protocol] and [[SC_Communication#Syscon_Services|SERV_SIRCS]]
|-
|-
| 4 || POW_SW || [[Template:Syscon_pinout_BGA_200_pads|Syscon Mullion]], pad B12 || Power Switch {{buttonpower}} ||  
| 4 || POW_SW || [[Template:Syscon_pinout_BGA_200_pads|Syscon]] pad B12 || Power Switch {{buttonpower}} ||  
|-
|-
| 5 || EJECT_SW || [[Template:Syscon_pinout_BGA_200_pads|Syscon Mullion]], pad A12 || Eject Switch {{buttoneject}} ||  
| 5 || EJECT_SW || [[Template:Syscon_pinout_BGA_200_pads|Syscon]] pad A12 || Eject Switch {{buttoneject}} ||  
|-
|-
| 6 || POW_LED || [[Template:Syscon_pinout_BGA_200_pads|Syscon Mullion]], pad M7 || Green led ||  
| 6 || POW_LED || [[Template:Syscon_pinout_BGA_200_pads|Syscon]] pad M7 || Green led ||  
|-
|-
| 7 || STBY_LED || [[Template:Syscon_pinout_BGA_200_pads|Syscon Mullion]], pad N7 || Red led ||  
| 7 || STBY_LED || [[Template:Syscon_pinout_BGA_200_pads|Syscon]] pad N7 || Red led ||  
|-
|-
| 8 || BD_LED || BluRay Connector, pin ? || Blue led ||  
| 8 || BD_LED || BluRay connector (CN3221) pin 50 || Blue led ||  
|-
|-
| 9 || {{cellcolors|#333333|white}} GND || GND || GND || Ground
| 9 || {{cellcolors|#333333|white}} GND || GND || GND || Ground
|-
|-
| 10 || {{cellcolors|#CC3333|white}} +5V_EVER || [[Power Supply]] <abbr title="CN???>Connector</abbr>, pins 4/5 ? || VCC || 5V Standby
| 10 || {{cellcolors|#CC3333|white}} +5V_EVER || [[Power Supply]] connector (CN6005) pins 4 and 5 || VCC || 5V Standby
|}
|}
<noinclude>[[Category:Templates]]</noinclude>
<noinclude>[[Category:Templates]]</noinclude>

Latest revision as of 04:56, 18 October 2022

CSW-001 Pinout
Pin Name Connected to Description
On Motherboard On Switch board
1 GND GND GND Ground
2 SW_PWM Syscon pad N9 Testpad ? FREQ. Intended to send a PWM signal to the switch board ?
3 RMC_IN Syscon pad R10
Service Connector (CN4009) pin 17
Testpad ?. NC ReMote Control INput
The IR receiver component is missing in the Switch board but existed in some PS3 prototypes that was using SIRC protocol and SERV_SIRCS
4 POW_SW Syscon pad B12 Power Switch PS3 power button
5 EJECT_SW Syscon pad A12 Eject Switch PS3 eject button
6 POW_LED Syscon pad M7 Green led
7 STBY_LED Syscon pad N7 Red led
8 BD_LED BluRay connector (CN3221) pin 50 Blue led
9 GND GND GND Ground
10 +5V_EVER Power Supply connector (CN6005) pins 4 and 5 VCC 5V Standby