Template:Syscon pinout BGA 200 pads: Difference between revisions
Jump to navigation
Jump to search
(Both names are official) |
No edit summary |
||
| Line 70: | Line 70: | ||
| A2 || DISC_IN || | | A2 || DISC_IN || | ||
|- | |- | ||
| B3 || SW_10 || | | B3 || data-sort-value="SW_9+1"| SW_10 || | ||
|- | |- | ||
| A3 || SW_0 || +5V, +3.3V, & +1.7V MISC | | A3 || SW_0 || +5V, +3.3V, & +1.7V MISC | ||
Revision as of 05:49, 27 June 2022
Pinout
| Pad# | Name | Port | Description |
|---|---|---|---|
| T2 | BE_INT | Port M Cell Control Line |
|
| R1 | PM7 | ||
| R2 | PM6 | ||
| P1 | BE_POWGOOD | ||
| P2 | BE_RESET | ||
| N1 | BE_SPI_CLK | Cell SPI Bus | |
| N2 | BE_SPI_DO | ||
| M1 | BE_SPI_DI | ||
| M2 | BE_SPI_CS | ||
| L4 | PL8 | Port N | unused |
| L5 | PL7 | ||
| K4 | PL6 | ||
| K5 | PL5 | ||
| J4 | PL4 | ||
| J5 | PL3 | ||
| H4 | PL2 | ||
| H5 | PL1 | ||
| H6 | PL0 | ||
| A8 | SB_SPI_CLK | Port K | Southbridge SPI Bus |
| B8 | SB_SPI_DO | ||
| A9 | SB_SPI_DI | ||
| B9 | SB_SPI_CS | ||
| A10 | DVE_I2C_SCL | ||
| B10 | DVE_I2C_SDA | ||
| A11 | ACDC_STBY | ||
| B11 | PK0 | ||
| B5 | PJ7 | Port J | |
| A5 | DISC_OUT12_SW | ||
| B2 | DISC_OUT8_SW | ||
| A2 | DISC_IN | ||
| B3 | SW_10 | ||
| A3 | SW_0 | +5V, +3.3V, & +1.7V MISC | |
| B4 | SW_8_B | +1.5V VDDIO for both AVCG & RSX Analog IO | |
| A4 | SW_8_C | +1.8V_RSX_PLL_VDD | |
| L16 | SW_PCI | Port I | |
| L15 | DISC_CHUCK | ||
| M16 | DISC_PHOT_LED | ||
| M15 | SW_2 | +1.8V_VDD_MEM & +1.8V_RSX_FBVDDQ | |
| N16 | DIAG_MODE | ||
| N15 | BACKUP_MODE | ||
| E6 | HDMI_INT | Port H | |
| D6 | VD_CECI0 | ||
| E7 | PH5 | ||
| D7 | RS_POW_FAIL | ||
| E8 | MUL_CHKSTP_IN | ||
| D8 | MUL_TRG_IN | ||
| E9 | SYS_THR_ALRT | ||
| D9 | SB_INT | ||
| M11 | SW_ATA | Port G | |
| N11 | SW_4_A | +1.2V, +1.9V, +3.3V ESW (Ethernet Controller) | |
| M10 | XDR_FET_VREF | ||
| N10 | XDR_FET_SCK | ||
| M9 | BUZZER | ||
| N9 | SW_PWM | Unknown output ? (connected to the Switch board) | |
| M8 | FANPWM1 | Secondary fan output (non-retail PS3 models only) | |
| N8 | FANPWM0 | Primary fan output (all PS3 models) | |
| E10 | MUL_CHKSTP_OUT | Port F | |
| D10 | MUL_TAG_OUT | ||
| E11 | SB_CGRESET | ||
| D11 | SB_RESET | ||
| E12 | BT_WAKEON | ||
| D12 | BE_VCS_1.25_ON | ||
| E13 | BE_VCS_1.30_ON | ||
| D13 | SW_1_A | +3.3V_MK_VDD for Clock Synthesizer | |
| A12 | EJECT_SW | Port E | |
| B12 | POW_SW | ||
| A13 | SB_EBUS_RESET | ||
| B13 | SB_EBUS_BRDY | ||
| A14 | PE3 | ||
| B14 | VD_CECI1 | ||
| A15 | BE_POW_FAIL | ||
| B15 | POW_FAIL | ||
| F13 | SW_5_B | Port D | |
| F12 | MK_EN | Connected to clock generator ICS1493G-18LFT (IC5001 pin #16 on COK-001) | |
| G13 | BEVRM_VID5 | ||
| G12 | BEVRM_VID4 | ||
| H13 | BEVRM_VID3 | ||
| H12 | BEVRM_VID2 | ||
| J13 | BEVRM_VID1 | ||
| J12 | BEVRM_VID0 | ||
| K13 | SW_HDD | Port C | |
| K12 | I2CBUS_EN | ||
| L13 | RSXVRM_VID5 | ||
| L12 | RSXVRM_VID4 | ||
| M13 | RSXVRM_VID3 | ||
| M12 | RSXVRM_VID2 | ||
| N13 | RSXVRM_VID1 | ||
| N12 | RSXVRM_VID0 | ||
| T15 | SW_8_A | Port B | +1.5V_YC_RC_VDDA (Analog voltage supplies, VDD_A) |
| R14 | SW_7_A | +1.0V_BE_VDDC (Cell BE core voltage supply (VDD) then VCS (the core array voltage). Note, the VID values stored on the CELL itself are not available to be read yet. So the default VID of the VRM is used until then. | |
| T14 | SW_6 | +1.2V_YC_RC_VDDIO (I/O voltage supplies, VDD_IO) | |
| R13 | SW_1_B | +2.5V_LREG_XCG_500_MEM. Analog Voltage for the core PLL of IC5004, Clock Generator used to support the Rambus XDR memory subsystem and Redwood logic interface. | |
| T13 | SW_4_B | +5V_USB, +1.8V_SB_PERI, +2.5V_SB_PLL_VDDC | |
| R12 | SW_3 | +1.2V_SB VDDC & VDDR | |
| T12 | VD_CECO1 | ||
| R11 | VD_CECO0 | ||
| N7 | STBY_LED | Port A | |
| M7 | POW_LED | ||
| N6 | AUDIO_MUTE | Uses a transistor, to switch another 2 transistors, that switches pins AOUTA#18 and AOUTB#15 of Cirrus CS4351-CZZR 192 kHz Stereo DAC (pins 9 and 11 of the MultiAV connector) | |
| M6 | SW_7_B | ||
| N5 | BT_RESET | ||
| M5 | GBE_RESET | ||
| N4 | SW_5_A | +1.2V_RSX_VDDC | |
| M4 | SW_9 | ||
| J16 | RBB | EEPROM Interface | |
| K16 | PI7 | ||
| J15 | WCB | ||
| K15 | PI6 | ||
| E16 | SKB | ||
| E15 | PP3 | ||
| G16 | DI | ||
| G15 | PP2 | ||
| H16 | DO | ||
| H15 | PP1 | ||
| F16 | CSB | ||
| F15 | PP0 | ||
| H11 | TESTMODE | Reset & Clock | |
| B16 | OSCOUT | ||
| C16 | OSCIN | ||
| D16 | 32KOUT | ||
| D15 | 32KIN | ||
| T5 | EXTAL | ||
| T4 | XTAL | ||
| T7 | XXTALO | ||
| J11 | RST | ||
| R4 | AVSUO | Power Port | Ground |
| R5 | AVDUO | +3.3v | |
| G6 | AVSS | Ground | |
| C2 | AVREF2 | Ground | |
| B1 | AVREF1 | +3.3v | |
| F7 | AVDD | +3.3v | |
| K11 | VSSF | Ground | |
| K6 | VSSF | Ground | |
| L6 | VDDF | +3.3v | |
| G7 | VSS | Ground | |
| G8 | |||
| G10 | |||
| T6 | |||
| R6 | |||
| T3 | |||
| L1 | |||
| E1 | |||
| C15 | VSSep | EEPROM Ground | |
| G11 | VDDep | EEPROM Power +3.3v | |
| F11 | VDDbat | +battery | |
| H7 | DVDD | +1.8v | |
| J10 | |||
| K10 | |||
| L10 | |||
| L11 | |||
| R7 | |||
| J7 | |||
| F8 | VDD3 | +3.3v | |
| F10 | |||
| H10 | |||
| J6 | |||
| F6 | |||
| D2 | VDD2 | +1.5V_RSX_VDDIO | |
| R3 | VDD1 | +1.2V_MC2_VDDIO | |
| L2 | VDD0 | +1.2V_MC2_VDDIO | |
| A16 | NC | ||
| T16 | |||
| T1 | |||
| A1 | |||
| G9 | |||
| F9 | |||
| L8 | JRTCK | JTAG Interface | |
| K8 | JTCK | ||
| K9 | JTDO | ||
| L9 | JTMS | ||
| K7 | JTDI | ||
| L7 | JNTAST | ||
| A6 | PR3 | Port R | |
| B6 | MC_P_OFF_REQ | ||
| A7 | MC_ALIVE | ||
| B7 | MC_RESERVED1 | ||
| R10 | RMC_IN | Port Q | Connected to missing IR receiver in the Switch boards (IR remote control input using SIRC protocol and SERV_SIRCS) |
| T11 | PQ5 | ||
| T10 | PQ4 | ||
| T8 | THR_I2C_SCL | ||
| T9 | THR_I2C_SDA | ||
| R9 | PQ1 | ||
| R8 | RSX_FBVDD_SEL | ||
| P16 | UART0_TxD | Port P | Serial Transmit |
| P15 | UART0_RxD | Serial Receive | |
| R16 | HDMI_I2C_SCL | ||
| R15 | HDMI_I2C_SDA | ||
| D1 | MK_I2C_SCL | Port O | Connected to clock generator ICS1493G-18LFT (IC5001 pin #46 on COK-001) |
| C1 | MK_I2C_SDA | Connected to clock generator ICS1493G-18LFT (IC5001 pin #47 on COK-001) | |
| G4 | PO7 | ||
| F4 | HDMI_RST0 | ||
| G5 | PO5 | ||
| F5 | DISC_IN_MECHA | ||
| E4 | EJECT_MECHA | ||
| D4 | XDR_FET_RST | ||
| E5 | GX_VSRST | ||
| D5 | XCG_EN | ||
| K2 | VD_VINT1 | Port N | |
| K1 | VD_VINT0 | ||
| J2 | RSX_INT | ||
| J1 | RSX_FLDO | ||
| H2 | PN6 | ||
| H1 | PN5 | ||
| G2 | RSX_RESET | ||
| G1 | RSX_SPI_CLK | RSX SPI Bus | |
| F2 | RSX_SPI_DO | ||
| F1 | RSX_SPI_DI | ||
| E2 | RSX_SPI_CS | ||