JAISPI

Someone should translate the spanish resources into english for wiki here, please.

JAISPI

JAISPI - Raspberry Pi SPI flasher for PS4

Source:

• http://jaicrab.org/?&a=Raspberry/Article/JAISPI
• http://jaicrab.org/?&a=Ps4/Tools/JAISPI

JAISPI - Utility to read and write to the main memory (MX25L25635FMI-10G) of PS4 with the Raspberry Pi through the SPI protocol.

Changelog

• v1.0
  • Support MX25L25635FMI-10G
  • Reading
  • Programming
  • Full Erase

Options

 -i /dev/spidevX.X             Get ID from flash
 -r file.bin /dev/spidevX.X    Read entire flash to file
 -e /dev/spidevX.X             Erase entire flash
 -p file.bin /dev/spidevX.X    Only write blocks differences from file
 -v file.bin /dev/spidevX.X    Verify blocks with file

Get ID

-i: Displays information of the flash.

#jaispi -i /dev/spidev0.0
JaiSpi v1.0
ID:  0xC22019 MX25L25635

Read

-r: Makes a full dump of the flash (Average time: 35sec)

#jaispi -r DUMP.bin /dev/spidev0.0
JaiSpi v1.0
ID:  0xC22019 MX25L25635
Reading...
0x02000000
Done!

Erase

-e: Clears all flash (Average time: 1min, 30sec)

#jaispi -e /dev/spidev0.0
JaiSpi v1.0
ID:  0xC22019 MX25L25635
Erasing blocks...
Done!

Program

-p: Write to flash only the changed sectors (Average time: 1min 30sec)

#jaispi -p Base.bin /dev/spidev0.0
JaiSpi v1.0
ID:  0xC22019 MX25L25635
Starting...
0x02000000 -> 8192 Sectors written
Done!

Verify

-v: Compares the flash contents with a file in PC (Average time: 35sec)

#jaispi -v Base.bin /dev/spidev0.0
JaiSpi v1.0
ID:  0xC22019 MX25L25635
Checking...
0x02000000 -> 0 Different sectors
Done!

Installation Instructions

Materials Required

• 1x RaspberryPi (raspberrypi.org)
• 1x SD Memory
• 1x Integrated MX25L25635FMI-10G (Main Memory PS4)

Downloads

• Raspbian (http://downloads.raspberrypi.org/raspbian_latest)
• Win32 Disk Imager (http://sourceforge.net/projects/win32diskimager/files/latest/download)
• Putty (http://the.earth.li/~sgtatham/putty/latest/x86/putty.exe)

Pinout

MX25L1006E Pinout

25X10CLYA1 Pinout

MX25L25635FMI-10G Pinout

Raspberry Pi GPIO pinout

8-Pin	16-pin	Usage	Raspberry Pi JAISPI	Description
-	1	SIO3	NC	8pin: Not Available - not used / 16pin: Serial Data Input & Output (for 4xI/O read mode)
8	2	VCC	17	+3V DC Power Supply
7	3	HOLD#/RESET#	NC	8pin: Hold, to pause the device without deselecting the device / 16pin: Hardware Reset Pin Active low
-	4	NC	NC	No Connection
-	5	NC	NC	No Connection
-	6	NC	NC	No Connection
1	7	CS#	24	Chip Select
2	8	SO/SIO1	21	Serial Data Output (for 1 x I/O) or Serial Data Input & Output (for 2x I/O or 4x I/O read mode)
3	9	WP#/SIO2	25	Write Protection: connect to GND or Serial Data Input & Output (for 4x I/O read mode)
4	10	GND	25	Ground
-	11	NC	NC	No Connection
-	12	NC	NC	No Connection
-	13	NC	NC	No Connection
-	14	NC	NC	No Connection
5	15	SI/SIO0	19	Serial Data Input (for 1 x I/O) or Serial Data Input & Output (for 2x I/O or 4x I/O read mode)
6	16	SCLK	23	Clock Input

Use short wires, esp. if you are not adding the 0.1µF capacitor between ground and vcc as close as possible to the chip

Installation

Run win32diskimage.
- In "Image file" select the Raspbian image downloaded and decompressed.
- In "Device" select the drive where the SD memory is.
- Select "Write".

Insert the SD in Raspberry fed by the USB cable. After two minutes, run Putty.
-In Host Name put: raspberrypi
-In case the previous step doesnt works properlly, go to the router and find the IP assigned to your RaspberryPi.
-Select SSH.
-Select Open.

It will request a Login. According Raspbian the user is "pi" and the password "raspberry" (Both without quotes).
Insert the following commands:

sudo-s
cd /bin
wget http://jaicrab.org/Ps4/Tools/JAISPI/jaispi
chmod +x jaispi
echo "# blacklist spi-bcm2708"> / etc / modprobe.d / blacklist.conf raspi-
echo "blacklist i2c-bcm2708" >> / etc / modprobe.d / blacklist.conf raspi-
reboot

Installation is complete. By Putty you can access the RaspberryPi. To run the command jaispi you need to be root (sudo-s):

# sudo-s
# Jaispi-i / dev/spidev0.0