JAISPI

Someone should translate the spanish resources into english for wiki here, please.

JAISPI

JAISPI - Raspberry Pi SPI flasher for PS4

Source:

• http://jaicrab.org/?&a=Raspberry/Article/JAISPI
• http://jaicrab.org/?&a=Ps4/Tools/JAISPI

JAISPI - Utility to read and write to the main memory (MX25L25635) of PS4 with the Raspberry Pi through the SPI protocol.

Changelog

• v1.0
  • Support MX25L25635.
  • Reading
  • Programming
  • Full Erase

Options

-I / dev / spidevX.X Get ID from flash
-E / dev / Erase Entire Flash spidevX.X
File.bin-r / dev / spidevX.X Read Entire file to flash
File.bin-p / dev / spidevX.X Differences Only write blocks from file
File.bin-v / dev / spidevX.X Verify blocks with file

-I: Displays information of the flash.

# Jaispi-i / dev/spidev0.0
JaiSpi v1.0
ID: 0xC22019 MX25L25635

-E: Clears all flash
Average time 1min, 30sec.

# Jaispi-e / dev/spidev0.0
JaiSpi v1.0
ID: 0xC22019 MX25L25635
Erasing blocks ...
Done!

-R: Makes a full dump of the flash.
Average time 35sec.

# Jaispi dump.bin-r / dev/spidev0.0
JaiSpi v1.0
ID: 0xC22019 MX25L25635
Reading ...
0x02000000
Done!

-P: Write to flash only the changed sectors.
Average time 1min 30sec

# Jaispi-p Base.bin / dev/spidev0.0
JaiSpi v1.0
ID: 0xC22019 MX25L25635
Starting ...
0x02000000 -> 8192 written Sectors
Done!

-V: Verify the contents of the flash with the filename.
Average time 35sec.

# Jaispi-v Base.bin / dev/spidev0.0
JaiSpi v1.0
ID: 0xC22019 MX25L25635
Checking ...
0x02000000 -> 0 the industries Different
Done!

Installation Instructions

Materials Required

• 1x RaspberryPi (raspberrypi.org)
• 1x SD Memory
• 1x Integrated MX25L25635 (Main Memory PS4)

Downloads

• Raspbian (downloads.raspberrypi.org/raspbian_latest)
• Win32 Disk Imager (sourceforge.net/projects/win32diskimager/files/latest/download)
• Putty (the.earth.li/~sgtatham/putty/latest/x86/putty.exe)

Pinout

MX25L1006E Pinout

25X10CLYA1 Pinout

MX25L25635FMI-10G Pinout

Raspberry Pi GPIO pinout

8-Pin	16-pin	Usage	Raspberry Pi JAISPI	Description
-	1	SIO3	NC	8pin: Not Available - not used / 16pin: Serial Data Input & Output (for 4xI/O read mode)
8	2	VCC	17	+3V DC Power Supply
7	3	HOLD#/RESET#	NC	8pin: Hold, to pause the device without deselecting the device / 16pin: Hardware Reset Pin Active low
-	4	NC	NC	No Connection
-	5	NC	NC	No Connection
-	6	NC	NC	No Connection
1	7	CS#	24	Chip Select
2	8	SO/SIO1	21	Serial Data Output (for 1 x I/O) or Serial Data Input & Output (for 2x I/O or 4x I/O read mode)
3	9	WP#/SIO2	25	Write Protection: connect to GND or Serial Data Input & Output (for 4x I/O read mode)
4	10	GND	25	Ground
-	11	NC	NC	No Connection
-	12	NC	NC	No Connection
-	13	NC	NC	No Connection
-	14	NC	NC	No Connection
5	15	SI/SIO0	19	Serial Data Input (for 1 x I/O) or Serial Data Input & Output (for 2x I/O or 4x I/O read mode)
6	16	SCLK	23	Clock Input

Use short wires, esp. if you are not adding the 0.1µF capacitor between ground and vcc as close as possible to the chip

Installation

Run win32diskimage.
File-In image select the image downloaded and decompressed Raspbian.
- In Device select the drive where the SD memory is.
We Power-Write.

We insert the SD in Raspberry and fed by the USB cable. After two minutes, run Putty.

-In Host Name put: raspberrypi
-De not work well the previous step, go to the router and find the IP assigned to your RaspberryPi.
-We marked SSH.
-We Power Open.

We request Login. According Raspbian the user is "pi" and the password "raspberry" (Both without quotes). We insert the following commands:

sudo-s cd / bin wget http://jaicrab.org/Ps4/Tools/JAISPI/jaispi chmod + x jaispi echo "# blacklist spi-bcm2708"> / etc / modprobe.d / blacklist.conf raspi- echo "blacklist i2c-bcm2708" >> / etc / modprobe.d / blacklist.conf raspi- reboot

Installation is complete. By Putty you can access the RaspberryPi. To run the command jaispi need to be root (sudo-s): # Sudo-s # Jaispi-i / dev/spidev0.0