JAISPI: Difference between revisions
Jump to navigation
Jump to search
(Created page with "{{Wikify}} Someone should translate the spanish resources into english for wiki here, please. == JAISPI == JAISPI - Raspberry Pi SPI flasher for PS4 Source: * http://jaic...") |
Standardbus (talk | contribs) m (Playstationhax thread link offline, replaced with a working updated link) |
||
| (38 intermediate revisions by 5 users not shown) | |||
| Line 1: | Line 1: | ||
{{Wikify}} | {{Wikify}} | ||
Someone should crosscheck the spanish and realworld into english for wiki here, please. | |||
Someone should | |||
== JAISPI == | == JAISPI == | ||
| Line 10: | Line 9: | ||
* http://jaicrab.org/?&a=Raspberry/Article/JAISPI | * http://jaicrab.org/?&a=Raspberry/Article/JAISPI | ||
* http://jaicrab.org/?&a=Ps4/Tools/JAISPI | * http://jaicrab.org/?&a=Ps4/Tools/JAISPI | ||
JAISPI - Utility to read and write to the main memory ([[MX25L25635FMI-10G]]) of PS4 with the Raspberry Pi through the SPI protocol. | |||
=== Changelog === | |||
* v1.0 | |||
** Support [[MX25L25635FMI-10G]] | |||
** Reading | |||
** Programming | |||
** Full Erase | |||
=== Installation Instructions === | |||
==== Materials Required ==== | |||
* 1x [[Raspberry Pi]] (see [[Raspberry_Pi#Where_to_buy.3F|here for where to buy]]) | |||
* 1x SD Memory (for Raspbian, a 4GB minimal is recommended) | |||
* 1x PS4 Serial Flash [[MX25L25635FMI-10G]] desoldered from console | |||
==== Downloads ==== | |||
* Raspbian (http://downloads.raspberrypi.org/raspbian_latest) | |||
* Win32 Disk Imager (http://sourceforge.net/projects/win32diskimager/files/latest/download) | |||
* Putty (http://the.earth.li/~sgtatham/putty/latest/x86/putty.exe) | |||
=== Pinout === | === Pinout === | ||
<div style="float:right">[[File:MX25L1006E Pinout.png|200px|thumb|left|[[MX25L1006E]] Pinout]]<br />[[File:25X10CLYA1 Pinout.png|200px|thumb|left|[[25X10CLYA1]] Pinout]]<br />[[File:MX25L25635FMI-10G Pinout.png|200px|thumb|left|[[MX25L25635FMI-10G]] Pinout]]<br /> | <div style="float:right">[[File:MX25L1006E Pinout.png|200px|thumb|left|[[MX25L1006E]] Pinout]]<br />[[File:25X10CLYA1 Pinout.png|200px|thumb|left|[[25X10CLYA1]] Pinout]]<br />[[File:MX25L25635FMI-10G Pinout.png|200px|thumb|left|[[MX25L25635FMI-10G]] Pinout]]<br /> | ||
[[File:Raspberry-pi-rev-1-gpio-pin-out1.jpg|200px|thumb|left|Raspberry Pi GPIO pinout]]</div> | [[File:Raspberry-pi-rev-1-gpio-pin-out1.jpg|200px|thumb|left|Raspberry Pi GPIO pinout]]<br />[[File:Raspberry Pi - model B plus - gpio.png|200px|thumb|left|Raspberry Pi model B+ GPIO pinout]]</div> | ||
{| border="1" cellspacing="0" cellpadding="5" border="#999" class="wikitable" style="border:1px solid #999; border-collapse: collapse;" | {| border="1" cellspacing="0" cellpadding="5" border="#999" class="wikitable" style="border:1px solid #999; border-collapse: collapse;" | ||
|- bgcolor="#cccccc" | |- bgcolor="#cccccc" | ||
| Line 55: | Line 75: | ||
Use short wires, esp. if you are not adding the 0.1{{micro}}F capacitor between ground and vcc as close as possible to the chip | Use short wires, esp. if you are not adding the 0.1{{micro}}F capacitor between ground and vcc as close as possible to the chip | ||
[http://www.raspberrypi.org/introducing-raspberry-pi-model-b-plus/ newer Raspberry Pi model B+] and Raspberry Pi model A+ both use same pinout for the first 26 pinheaders as the previous nonplus model, so it should work on that as well. | |||
=== Installation === | |||
==== Installing Raspbian ==== | |||
Run win32diskimage (if you use linux you can use dd)<br /> | |||
[[File:Win32DiskImager.png]] | |||
# In "Image file" select the downloaded and decompressed Raspbian image (''2013-09-25-wheezy-raspbian.img'' at the time of this writing) | |||
# In "Device" select the drive where the SD memory is. | |||
# Select "Write". | |||
After finished writing, put the SD card in the Raspberry Pi and power it up by inserting the USB cable. | |||
==== Remote Shell into Raspbian ==== | |||
Two minutes after booting up the Raspberry Pi, run Putty.<br /> | |||
[[File:Putty.png]] | |||
# In Host Name put: raspberrypi<br />If this doesn't works properly, go to the router, find the IP assigned to your Raspberry Pi and use that instead, | |||
# Select SSH (or Raspberry and Putty support TTL https://learn.adafruit.com/adafruits-raspberry-pi-lesson-5-using-a-console-cable/overview) | |||
# Select Open | |||
==== Installing Application ==== | |||
It will request a Login. According Raspbian the user is "pi" and the password "raspberry" (Both without quotes). | |||
Insert the following commands: | |||
{{keyboard|content= | |||
sudo -s | |||
cd /bin | |||
wget http://jaicrab.org/Ps4/Tools/JAISPI/jaispi | |||
chmod +x jaispi | |||
echo "#blacklist spi-bcm2708" > /etc/modprobe.d/raspi-blacklist.conf | |||
echo "blacklist i2c-bcm2708" >> /etc/modprobe.d/raspi-blacklist.conf | |||
reboot | |||
}} | |||
Installation is complete. By Putty you can access the Raspberry Pi. To run the command jaispi you need to be root (sudo-s): | |||
{{keyboard|content= | |||
# sudo -s | |||
# Jaispi -i / dev/spidev0.0 | |||
}} | |||
=== Options === | |||
-i /dev/spidevX.X Get ID from flash | |||
-r file.bin /dev/spidevX.X Read entire flash to file | |||
-e /dev/spidevX.X Erase entire flash | |||
-p file.bin /dev/spidevX.X Only write blocks differences from file | |||
-v file.bin /dev/spidevX.X Verify blocks with file | |||
==== Get ID ==== | |||
-i: Displays information of the flash. | |||
#jaispi -i /dev/spidev0.0 | |||
JaiSpi v1.0 | |||
ID: 0xC22019 MX25L25635 | |||
==== Read ==== | |||
-r: Makes a full dump of the flash (Average time: 35sec) | |||
#jaispi -r DUMP.bin /dev/spidev0.0 | |||
JaiSpi v1.0 | |||
ID: 0xC22019 MX25L25635 | |||
Reading... | |||
0x02000000 | |||
Done! | |||
==== Erase ==== | |||
-e: Clears all flash (Average time: 1min, 30sec) | |||
#jaispi -e /dev/spidev0.0 | |||
JaiSpi v1.0 | |||
ID: 0xC22019 MX25L25635 | |||
Erasing blocks... | |||
Done! | |||
==== Program ==== | |||
-p: Write to flash only the changed sectors (Average time: 1min 30sec) | |||
#jaispi -p Base.bin /dev/spidev0.0 | |||
JaiSpi v1.0 | |||
ID: 0xC22019 MX25L25635 | |||
Starting... | |||
0x02000000 -> 8192 Sectors written | |||
Done! | |||
==== Verify ==== | |||
-v: Compares the flash contents with a file in PC (Average time: 35sec) | |||
#jaispi -v Base.bin /dev/spidev0.0 | |||
JaiSpi v1.0 | |||
ID: 0xC22019 MX25L25635 | |||
Checking... | |||
0x02000000 -> 0 Different sectors | |||
Done! | |||
=== JAISPI / PS4 NOR Chip Dumping personal experience by AlphaHack === | |||
PS4 NOR Chip Dumping Process Documentation | |||
* [https://www.mediafire.com/?6jcpwd7mzw6fnsk as PDF] | |||
* [https://playstationhax.xyz/forums/topic/1749-ps4-nor-chip-dumping-process-documentation/ as forumtopic] | |||
{{Hardware Modification}} | {{Hardware Modification}} | ||
<noinclude>[[Category:Main]]</noinclude> | <noinclude>[[Category:Main]]</noinclude> | ||
Latest revision as of 14:56, 10 February 2017
| This article is marked for rewrite/restructuring in proper wiki format. You can help PS4 Developer wiki by editing it. |
Someone should crosscheck the spanish and realworld into english for wiki here, please.
JAISPI[edit | edit source]
JAISPI - Raspberry Pi SPI flasher for PS4
Source:
JAISPI - Utility to read and write to the main memory (MX25L25635FMI-10G) of PS4 with the Raspberry Pi through the SPI protocol.
Changelog[edit | edit source]
- v1.0
- Support MX25L25635FMI-10G
- Reading
- Programming
- Full Erase
Installation Instructions[edit | edit source]
Materials Required[edit | edit source]
- 1x Raspberry Pi (see here for where to buy)
- 1x SD Memory (for Raspbian, a 4GB minimal is recommended)
- 1x PS4 Serial Flash MX25L25635FMI-10G desoldered from console
Downloads[edit | edit source]
- Raspbian (http://downloads.raspberrypi.org/raspbian_latest)
- Win32 Disk Imager (http://sourceforge.net/projects/win32diskimager/files/latest/download)
- Putty (http://the.earth.li/~sgtatham/putty/latest/x86/putty.exe)
Pinout[edit | edit source]
| 8-Pin | 16-pin | Usage | Raspberry Pi JAISPI |
Description |
|---|---|---|---|---|
| - | 1 | SIO3 | NC | 8pin: Not Available - not used / 16pin: Serial Data Input & Output (for 4xI/O read mode) |
| 8 | 2 | VCC | 17 | +3V DC Power Supply |
| 7 | 3 | HOLD#/RESET# | NC | 8pin: Hold, to pause the device without deselecting the device / 16pin: Hardware Reset Pin Active low |
| - | 4 | NC | NC | No Connection |
| - | 5 | NC | NC | No Connection |
| - | 6 | NC | NC | No Connection |
| 1 | 7 | CS# | 24 | Chip Select |
| 2 | 8 | SO/SIO1 | 21 | Serial Data Output (for 1 x I/O) or Serial Data Input & Output (for 2x I/O or 4x I/O read mode) |
| 3 | 9 | WP#/SIO2 | 25 | Write Protection: connect to GND or Serial Data Input & Output (for 4x I/O read mode) |
| 4 | 10 | GND | 25 | Ground |
| - | 11 | NC | NC | No Connection |
| - | 12 | NC | NC | No Connection |
| - | 13 | NC | NC | No Connection |
| - | 14 | NC | NC | No Connection |
| 5 | 15 | SI/SIO0 | 19 | Serial Data Input (for 1 x I/O) or Serial Data Input & Output (for 2x I/O or 4x I/O read mode) |
| 6 | 16 | SCLK | 23 | Clock Input |
Use short wires, esp. if you are not adding the 0.1µF capacitor between ground and vcc as close as possible to the chip
newer Raspberry Pi model B+ and Raspberry Pi model A+ both use same pinout for the first 26 pinheaders as the previous nonplus model, so it should work on that as well.
Installation[edit | edit source]
Installing Raspbian[edit | edit source]
Run win32diskimage (if you use linux you can use dd)
- In "Image file" select the downloaded and decompressed Raspbian image (2013-09-25-wheezy-raspbian.img at the time of this writing)
- In "Device" select the drive where the SD memory is.
- Select "Write".
After finished writing, put the SD card in the Raspberry Pi and power it up by inserting the USB cable.
Remote Shell into Raspbian[edit | edit source]
Two minutes after booting up the Raspberry Pi, run Putty.
- In Host Name put: raspberrypi
If this doesn't works properly, go to the router, find the IP assigned to your Raspberry Pi and use that instead, - Select SSH (or Raspberry and Putty support TTL https://learn.adafruit.com/adafruits-raspberry-pi-lesson-5-using-a-console-cable/overview)
- Select Open
Installing Application[edit | edit source]
It will request a Login. According Raspbian the user is "pi" and the password "raspberry" (Both without quotes).
Insert the following commands:
sudo -s cd /bin wget http://jaicrab.org/Ps4/Tools/JAISPI/jaispi chmod +x jaispi echo "#blacklist spi-bcm2708" > /etc/modprobe.d/raspi-blacklist.conf echo "blacklist i2c-bcm2708" >> /etc/modprobe.d/raspi-blacklist.conf reboot
Installation is complete. By Putty you can access the Raspberry Pi. To run the command jaispi you need to be root (sudo-s):
# sudo -s # Jaispi -i / dev/spidev0.0
Options[edit | edit source]
-i /dev/spidevX.X Get ID from flash -r file.bin /dev/spidevX.X Read entire flash to file -e /dev/spidevX.X Erase entire flash -p file.bin /dev/spidevX.X Only write blocks differences from file -v file.bin /dev/spidevX.X Verify blocks with file
Get ID[edit | edit source]
-i: Displays information of the flash.
#jaispi -i /dev/spidev0.0 JaiSpi v1.0 ID: 0xC22019 MX25L25635
Read[edit | edit source]
-r: Makes a full dump of the flash (Average time: 35sec)
#jaispi -r DUMP.bin /dev/spidev0.0 JaiSpi v1.0 ID: 0xC22019 MX25L25635 Reading... 0x02000000 Done!
Erase[edit | edit source]
-e: Clears all flash (Average time: 1min, 30sec)
#jaispi -e /dev/spidev0.0 JaiSpi v1.0 ID: 0xC22019 MX25L25635 Erasing blocks... Done!
Program[edit | edit source]
-p: Write to flash only the changed sectors (Average time: 1min 30sec)
#jaispi -p Base.bin /dev/spidev0.0 JaiSpi v1.0 ID: 0xC22019 MX25L25635 Starting... 0x02000000 -> 8192 Sectors written Done!
Verify[edit | edit source]
-v: Compares the flash contents with a file in PC (Average time: 35sec)
#jaispi -v Base.bin /dev/spidev0.0 JaiSpi v1.0 ID: 0xC22019 MX25L25635 Checking... 0x02000000 -> 0 Different sectors Done!
JAISPI / PS4 NOR Chip Dumping personal experience by AlphaHack[edit | edit source]
PS4 NOR Chip Dumping Process Documentation
| |||||||||||||||||||||||||||||||
