Move Motion Controller: Difference between revisions
m (link to photos) |
(index reordered, some notes added) |
||
| Line 1: | Line 1: | ||
[[Category:Hardware]] | [[Category:Hardware]] | ||
== | == Move Hardware == | ||
*Model nº | *Model nº | ||
**CECH-ZCM1U (bought in ?) | **CECH-ZCM1U (bought in ?) | ||
| Line 60: | Line 60: | ||
**LED_4R5 (VDD line) | **LED_4R5 (VDD line) | ||
== External Conectors == | === External Conectors === | ||
=== | ==== USB connector ==== | ||
USB (Mini-B type) standard connector 5 pins | |||
http://pinoutsguide.com/Slots/USB_pinout.shtml | http://pinoutsguide.com/Slots/USB_pinout.shtml | ||
=== | ==== Charging Station Pads ==== | ||
2 copper pads that are part of a little PCB with no traces that works as a support for the pads. Are soldered (no connectors) to the main board with 2 wires: black (ground) red (volts) | |||
http://www.youtube.com/watch?v=TkPFKrlWWwk | http://www.youtube.com/watch?v=TkPFKrlWWwk | ||
=== Move Sharp Shooter | *This pads are common and has the same size and position than the [[Move Navigation Controller]] | ||
==== Extension Connector ==== | |||
Marked in the plastic as "ext" and refered as "extension connector" in the [[Move Sharp Shooter]] "Instruction Manual.pdf" | |||
8 pins custom made ? (smaller than the Mini-B) | 8 pins custom made ? (smaller than the Mini-B) | ||
The connector is soldered in a "children board" | |||
The connector is soldered in a "children board" identifyed as "connector board", is connected with the "main board" with a 12 traces ribbon cable (and 2 pressure connectors). Only 4 lines of the ribbon cable are used for data signals (each line is protected with a resistor and a diode in the children board) + 1 line that seems to be common and is much more wide (probably volts or ground). The other lines are not used. | |||
*This connector is used to communicate with the [[Move Sharp Shooter]] gun. The buttons, trigger, etc... of this gun can send signals to the move controller | *This connector is used to communicate with the [[Move Sharp Shooter]] gun. The buttons, trigger, etc... of this gun can send signals to the move controller | ||
== Software Support == | |||
=== Move In PS3 === | |||
*PSl1ght supports move controller by faking the device as a wireless mouse, there is no support for native move modules/functions (yet) | |||
=== Move In PC === | |||
*Playstation Move Framework: http://code.google.com/p/moveframework/ (src available with svn) | |||
{{Console}} | {{Console}} | ||
[[Category:Peripherals]] | [[Category:Peripherals]] | ||
Revision as of 16:18, 1 September 2012
Move Hardware
- Model nº
- CECH-ZCM1U (bought in ?)
- CECH-ZCM1E (bought in europe)
Some photos of a dissassembled move controller ---> http://www.ifixit.com/Teardown/PlayStation-Move-Teardown/3594/1
ARM STM32F103 VBT6 Y (32bit MCU)
U19
http://www.st.com/mcu/devicedocs-STM32F103VB-110.html
Y5250H 2029 K8QEZ (Gyro?)
alt.no.: Y5250H 2005 4Y84AQ
alt.no.: Y5250H 2024 GPECQ
U14
Kionix KXSC4 10227 2410 (Accelerometer)
alt.no.: Kionix KXSC4-XLU 90831 3909
alt.no.: Kionix KXSC4 10115 2010
U12
http://www.kionix.com/
Texas Instruments BQ24080 (1-cell Li-Ion Charger)
alt.no.:BRO 01J PDH2
alt.no.:BRO 04K 0948
U1
TPS63030 (High Efficient Single Inductor Buck-Boost Converter)
alt.no.:CEE TI J 04P0
U6
Cambridge Silicon Radio BC4RE A16U (Bluetooth transmitter)
U8?
http://www.csr.com/products/technology/bluetooth
AKM AK8974 (three-axis Electronic Compass -MEMS)
alt.no.:AKM8974 948D
alt.no.:AKM8974 008F
U13
http://www.chipworks.com/seamark.aspx?sm=s4%3BDatedfl11%3BDevCategory12%3BMEMS+Devicesm12%3BReleaseMonthm10%3BDeviceTypefl10%3BReportCode12%3BEXR-0908-802&cw=detail2
ALPS 503A 04C (Radio Module)
Li-Ion (Battery Pack)
4-168-108-01 / LIS1441
3.7V 1380 mAh
(typ 1520mAh)
Charge Current: 1.4A
Charge Voltage: 4.25V
LED2
6 pins surface mounted RGB 2^24
- Soldered to the board with a ribbon cable (no connectors) with 4 lines marked as:
- LED_B
- LED_G
- LED_R
- LED_4R5 (VDD line)
External Conectors
USB connector
USB (Mini-B type) standard connector 5 pins
http://pinoutsguide.com/Slots/USB_pinout.shtml
Charging Station Pads
2 copper pads that are part of a little PCB with no traces that works as a support for the pads. Are soldered (no connectors) to the main board with 2 wires: black (ground) red (volts)
http://www.youtube.com/watch?v=TkPFKrlWWwk
- This pads are common and has the same size and position than the Move Navigation Controller
Extension Connector
Marked in the plastic as "ext" and refered as "extension connector" in the Move Sharp Shooter "Instruction Manual.pdf"
8 pins custom made ? (smaller than the Mini-B)
The connector is soldered in a "children board" identifyed as "connector board", is connected with the "main board" with a 12 traces ribbon cable (and 2 pressure connectors). Only 4 lines of the ribbon cable are used for data signals (each line is protected with a resistor and a diode in the children board) + 1 line that seems to be common and is much more wide (probably volts or ground). The other lines are not used.
- This connector is used to communicate with the Move Sharp Shooter gun. The buttons, trigger, etc... of this gun can send signals to the move controller
Software Support
Move In PS3
- PSl1ght supports move controller by faking the device as a wireless mouse, there is no support for native move modules/functions (yet)
Move In PC
- Playstation Move Framework: http://code.google.com/p/moveframework/ (src available with svn)