Downgrading with linux

You should have grafchokolos modules, and patches installed

This works on 3.55 without a physical dongle

Use this method to install lower firmware! You can install a newer firmware ex 3.60 with this method but you will be loosing your homebrew

Downgrade Method - Emulating JIG with Linux

1st step – Generating a challenge

---

1. ps3dm_usb_dongle_auth /dev/ps3dmproxy gen_challenge

2nd step – Generating a valid response for a challenge

---

You need a dongle id. Valid range for dongle IDs is 0×0000 – 0xffff. So choose one, doesn’t matter which one, but some are revoked !!!

1. ps3dm_usb_dongle_auth /dev/ps3dmproxy gen_resp 0xBABE “here is a challenge like this 0xXX 0xXX … of size 20 bytes”

3rd step – Verifying response (Enabling “Product Mode”)

---

1. ps3dm_usb_dongle_auth /dev/ps3dmproxy verify_resp 0xBABE

“here is the response from step 2 like this 0xXX 0xXX … of size 20 bytes”

4th step – Checking if “Product Mode” is enabled

---

The returned value shouldn’t be 0xff.

1. ps3dm_um /dev/ps3dmproxy read_eprom 0x48C07

5th step - Inspect if CORE_OS_PACKAGE.pkg isn't damaged

---

ps3dm_um /dev/ps3dmproxy inspect_pkg 1 0x9 CORE_OS_PACKAGE.pkg

6th step - Install CORE_OS_PACKAGE.pkg

---

ps3dm_um /dev/ps3dmproxy update_pkg 1 0x9 CORE_OS_PACKAGE.pkg

7th step – Disabling “Product Mode”

---

1. ps3dm_um /dev/ps3dmproxy write_eprom 0x48C07 0xff

This step is really important, if Product Mode isn't disabled you will need a dongle to get out of it

ALTERNATIVE METHOD - not tested

1st step – Enabling product mode

---

1. ps3dm_um /dev/ps3dmproxy write_eprom 0x48C07 0xfe

2th step – Checking if “Product Mode” is enabled

---

The returned value shouldn’t be 0xff.

1. ps3dm_um /dev/ps3dmproxy read_eprom 0x48C07

3th step - Inspect if CORE_OS_PACKAGE.pkg isn´t damaged

---

ps3dm_um /dev/ps3dmproxy inspect_pkg 1 0x9 CORE_OS_PACKAGE.pkg

4th step - Install CORE_OS_PACKAGE.pkg

---

ps3dm_um /dev/ps3dmproxy update_pkg 1 0x9 CORE_OS_PACKAGE.pkg

5th step – Disabling “Product Mode”

---

1. ps3dm_um /dev/ps3dmproxy write_eprom 0x48C07 0xff

This step is really important, if Product Mode isn´t disabled you will need a dongle to get out of it

Install debug firmware

High brick risk! Don´t try this if you don´t know what you are doing

If you brick with this the only way to recover is Hardware flashing the prior to conversion made dump back to the NAND/NOR flash

To install debug firmware, EID0 (and EID5?) should be reencrypted and rehashed with the proper Target ID and Device ID/type

Debugging Station Target ID: 0x82

eEID contains

• system model data
• target ID
• PS3 motherboard revision
• Per ps3 values (console id, psid...)

"The kernel and most of the loaders check the Target ID as well as the Device ID/type to see if your unit is debug or not and if not they disable all the fancy things such as running unsigned code (in the case of appldr).

• a good read about SC http://rms.grafchokolo.com/?p=16