Hardware flashing

Progskeet wired to NANDs of a COK-002 board (photo:idone)

Typical NOR flashing requires 16 Data wires, 23 Address wires and 3-4 control wires to the NOR pads (photo:defyboy)

Both early launch consoles which feature NAND flash memory (block devices, that interleave their data unlike NOR flash) and later consoles which feature NOR flash memory are able to be flashed. Currently the preferred method of flashing the dual-NAND consoles is by using an infectus modchip or similar (e.g. Progskeet).

Marcan has made a NOR flasher / address sniffer for his PS3 slim by re-purposing a FPGA board (Xilinx Spartan3E XC3S500E) made for Wii hacking. noralizer is a git repo that contains the HDL (verilog) and associated host computer tools for flashing/sniffing. There are ~50 signals to solder.

Work has been underway to brink a low cost AVR (Atmel 90USB1286) based NOR flasher that is capable of reading and writing on all consoles by defyboy. Other people havent been sitting idle either: uf6667 and Icekiller have developed Progskeet, based on a Actel A3P125 MCU for NAND ánd NOR based consoles and "no_one" has developed PNM - Project Nor Manager.

NAND Wiring

Flashers for NAND based consoles (CECHA/COK-001, CECHB/COK-001, CECHC/COK-002, CECHD/unreleased, CECHE/COK-002W, CECHF/unreleased, CECHG/SEM-001) are generaly wired directly to the pins of the NAND, plus ground and Vcc. For NAND pinouts see: Flash (Hardware) #NAND

There are 2 nands interleaved at the 512byte sectors level, giving a 1024 byte "interleaved sector". pages are 2kb on each nand.

Dual NAND connection to Progskeet diagram, see http://progskeet.com/

Dual NAND connection to Infectus diagram

Chip/PIN	Description	Progskeet	Infectus	Description
NAND 0
0/1-6	NC	NC	NC	No Connection
0/7	R/B	3 / gp13	A9	Read/Busy Output
0/8	RE	98 / gp15	A15	Read Enable
0/9	CE	7 / gp9	A14	Chip Enable
0/10+11	NC	NC	NC	No Connection
0/12	Vcc	+3.3	not used / not connected	Vcc (min 2.7V-max 3.6V / typ 3.3V)
0/13	Vss	GND	not used / not connected	VSS - Ground
0/14+15	NC	NC	NC	No Connection
0/16	CLE	4 / gp12	A13	Command Latch Enable
0/17	ALE	5 / gp11	A12	Address Latch Enable
0/18	WE	2 / gp14	A11	Write Enable
0/19	WP	6 / gp10	A10	Write Protect
0/20-28	NC	NC	NC	No Connection
0/29	I/O-0	90 / dq8	A0
0/30	I/O-1	91 / dq9	A1
0/31	I/O-2	92 / dq10	A2
0/32	I/O-3	93 / dq11	A3
0/33-35	NC	NC	NC	No Connection
0/36	Vss	GND	not used / not connected	VSS - Ground
0/37	Vcc	+3.3	not used / not connected	Vcc (min 2.7V-max 3.6V / typ 3.3V)
0/38-40	NC	NC	NC	No Connection
0/41	I/O-4	94 / dq12	A4
0/42	I/O-5	95 / dq13	A5
0/43	I/O-6	96 / dq14	A6
0/44	I/O-7	97 / dq15	A7
0/45-48	NC	NC	NC	No Connection
Chip/PIN	Description	Progskeet	Infectus	Description
NAND 1
1/1-6	NC	NC	NC	No Connection
1/7	R/B	64 / rdy	U	Read/Busy Output
1/8	RE	69 / oe	M	Read Enable
1/9	CE	60 / gp3	N	Chip Enable
1/10+11	NC	NC	NC	No Connection
1/12	Vcc	+3.3	not used / not connected	Vcc (min 2.7V-max 3.6V / typ 3.3V)
1/13	Vss	GND	not used / not connected	VSS - Ground
1/14+15	NC	NC	NC	No Connection
1/16	CLE	63 / gp0	O	Command Latch Enable
1/17	ALE	62 / gp1	P	Address Latch Enable
1/18	WE	65 / we	Q	Write Enable
1/19	WP	61 / gp2	T	Write Protect
1/20-28	NC	NC	NC	No Connection
1/29	I/O-0	79 / dq0	D0
1/30	I/O-1	80 / dq1	D1
1/31	I/O-2	81 / dq2	D2
1/32	I/O-3	82 / dq3	D3
1/33-35	NC	NC	NC	No Connection
1/36	Vss	GND	not used / not connected	VSS - Ground
1/37	Vcc	+3.3	not used / not connected	Vcc (min 2.7V-max 3.6V / typ 3.3V)
1/38-40	NC	NC	NC	No Connection
1/41	I/O-4	83 / dq4	D4
1/42	I/O-5	84 / dq5	D5
1/43	I/O-6	85 / dq6	D6
1/44	I/O-7	86 / dq7	D7
1/45-48	NC	NC	NC	No Connection
Board trace
GND	Vss	not used / not connected	GND	VSS - Ground
+5V	Vcc	not used / not connected	5V	Vcc (typ +5VDC) from TH3401

Remarks:

• Progskeet is feeded from NAND 3.3V
• Infectus is feeded from +5V board trace.
• NAND's are feeded in both cases by the console itself.

Progskeet Note: Some modification is needed for Progskeet to unbrick:

• desolder R8 from the Progskeet PCB (to disable the connection from pad R8 to left pad R7)
• left pin of toggle switch to left lead of R7, middle pin of toggle switch to right lead of R7
• Vcc to +3.3 // put toggle switch in "OFF" (right) postion, power on the ps3, put the toggle switch in the "ON"/left position, it will be recognized by the PC, NAND is always on now, do everything as usual.

Using NAND flashers

Progskeet

... nothing yet ... please help by adding this :)

put switch in "OFF" (R7 is open) position so that progskeet is not powered.
power on the ps3 and wait for 20-25 seconds,
put the switch in the "ON" (R7 closed) position, so progskeet is powered and will be recognized by the PC.
NAND is always on now, do everything as usual

select Big Block
select Raw
Pages per block: 64
blocks: 1024

That will give you 132MB (138,412,032 bytes) per NAND (dump time ~ 00:02:40 per NAND)

downloads

All current downloads are available here

• diagrams - for PS3: see above, but others are available here: diagrams_110805.rar (backup/mirror: diagrams_110803.rar (4.76 MB))
• drivers - diagrams_110804.rar (mirror: diagrams_110804.rar (9.73 MB))
• flasher software - ProgSkeet_110811-B.rar (mirror: ProgSkeet_110811-B.rar (29.8 KB)

Infectus

For Infectus don't use 3.9.9.0, as it removes dual NAND PS3 support :S If your board already came with this version or higher, use this: prepare_infectus_for_ps3.rar (5.53 MB) If it is done, it will show up as "2 NAND Programmer" in the bottom left. Dual NAND PS3 compatible version: Infectus_programmer_3.8_Beta_2.zip (4.02 MB)

Power the Infectus, it crashes the PS3 and leaves the NANDs in powered mode. Use the console to power the NANDs: power it up until the PS3 crashes and halts with red flashing LED, press power again to stop the flashing, but keeps the console powered on. The NANDs are not accessed by the PS3 in this way, so it doesn't matter if the NAND content is already messed up. After that, you can read/write the NANDs.

Dumping of single NAND should take about 15 minutes, 30 minutes for both.

Needed NAND tools

In case the flasher program doesnt understand dual NAND de/interleaving you'll need : FlowRebuilder v.4.1.0.0 / FlowRebuilder v.4.1.3.2.exe (459.95 KB)

Dump NAND from GameOS

dump_flash.pkg // backup/mirror: dump-flash+syscon.rar (280.51 KB)
Make sure USB stick is FAT32 with enough free space (256MB per dump)

Difference between hardware dumps and software dumps

ps3vflasha

hardware dumps

256 MB (268,435,456 bytes) bootldr is at 0x000000 on NAND (0xFC0000 on NOR)

software dumps

dump size = 239 MB (251,396,096 bytes)
bootldr not at 0x000000 on NAND :

00000000   00 00 00 00 00 00 00 00  00 00 00 00 00 00 00 00   ................
00000010   00 00 00 00 0F AC E0 FF  00 00 00 00 DE AD BE EF   .....¬à ÿ....Þ­¾ï

reason:

addi    %r12, %r4, 0x200 # r4 = start sector

25MB NAND consoles have a hidden section of size 0x40000 (0x200 * 512 byte sector = 0x40000) hidden by the hv. The hv hides it at address 002786E8

Original code : 0x39840200f8010090
Change to : 0x39840000f8010090

Too dangerous to patch unless you peek/poke because obviously it messes with all the offsets

'NOR' Interface Testpoints on NAND consoles

Simular as on the NOR based consoles testpoints can be found on the back of the PCB. It seems these are from the bus between the South Bridge and the Starship2. Attempts have been made to document/trace these. Addresslines 0-17 and Datalines 0-15 as well as some controllines are documented but so far these could not be used to read/flash the console in a NOR fashion.

NOR Interface Testpoints

Probably to aid in factory programming, Sony provides NOR testpoints on the bottomside of the motherboard. There are 16 data lines (Word access) and generally 23 Address lines. You will also need to control Chip Enable (#CE), Write Enable (#WE), Tristate (SB_DISABLE) and for some boards Write Protect (#WP)

Tristate

Tristate, or as it is referred to in the service manuals SB_DISABLE exists solely for the purpose of placing the South Bridge pins into high-impedance (the third state) so that we can access the flash without the South Bridge interfering.

Because the tristate pin is not connected to the NOR flash TSOP package, but to the South Bridge BGA package, this makes tracing the pin quite difficult. One should be able to locate it by having the running you could ground out the unknown pins whilst checking the continuity of a known address or data line against ground. These should enter high-impedance or no-continuity when you ground out SB_DISABLE.

Connecting NOR pads to flasher

Teensy 2.0 ++ connection diagram for PS3 NOR pads))

Progskeet NAND/NOR flasher board, based on Actel MCU, see http://progskeet.com/)

PAD	Progskeet	Teensy2.0++ NORway
A0	adr0	F0
A1	adr1	F1
A2	adr2	F2
A3	adr3	F3
A4	adr4	F4
A5	adr5	F5
A6	adr6	F6
A7	adr7	F7
A8	adr8	PA0
A9	adr9	PA1
A10	adr10	PA2
A11	adr11	PA3
A12	adr12	PA4
A13	adr13	PA5
A14	adr14	PA6
A15	adr15	PA7
A16	adr16	B0
A17	adr17	B1
A18	adr18	B2
A19	adr19	B3
A20	adr20	B4
A21	adr21	B5
A22	adr22	B6
DQ0	dq0	D0
DQ1	dq1	D1
DQ2	dq2	D2
DQ3	dq3	D3
DQ4	dq4	D4
DQ5	dq5	D5
DQ6	dq6	D6
DQ7	dq7	D7
DQ8	dq8	C0
DQ9	dq9	C1
DQ10	dq10	C2
DQ11	dq11	C3
DQ12	dq12	C4
DQ13	dq13	C5
DQ14	dq14	C6
DQ15	dq15	C7
#WE	we	E5
CE#	gp0	E0
RESET	gp1	E4
TRISTATE	gp2	E7
WP#	gp3	?tied to Vcc?
OE#	oe	E1
RY/BY#	rdy	E6
VSS	GND	GND

Progskeet Note: Some modification is needed for Progskeet to unbrick:

• desolder R8 from the Progskeet PCB
• left pin of switch to left lead of R7, middle pin of switch to right lead of R7
• Vcc to +3.3 // put switch in "OFF" (right) postion, power on the ps3, put the switch in the "ON"/left position, it will be recognized by the PC, NOR is always on now, do everything as usual.

Notes: The Teensy requires a 3.3V voltage regulator! 5V trace has to be cut and 3V pads have to be shorted! Please refer to https://www.pjrc.com/teensy/3volt.html

Speed comparison NOR flashers

Speed comparison NOR flashers
	Teensy (NORway 0.1)		Teensy (NORway 0.3)		Progskeet
	time (h:mm:ss)	speed (KB/sec)	time (h:mm:ss)	speed (KB/sec)	time (h:mm:ss)	speed (KB/sec)
Full dump/read (16 MB)	0:05:11	52,68 KB/s	0:00:45	364,08 KB/s	0:00:16	1024 KB/s
Per sector write(128 KB)	0:01:35	1,35 KB/s	0:00:05.351	23,92 KB/s	0:00:00.365	350,69 KB/s
Full dump/write (16 MB)	2:08:19	2,12 KB/s	0:08:19	32,83 KB/s	0:00:46.811	350,00 KB/s

Using NOR flashers

Progskeet

take the cable out the back
plug it back in
put the switch on "off"
power on
wait 10 seconds
put the switch on "on"
 
dump:
- Spansion NOR: 128KB sector, 128 sectors
- Samsung NOR:  4KB sector, 4096 sectors

Needed NOR tools

• norunpack (usage: norunpack dump.b directory) git: http://git.dashhacks.com/ps3free/ps3tools

Dump NOR from GameOS

dump_flash.pkg // backup/mirror: dump-flash+syscon.rar (280.51 KB)
Make sure USB stick is FAT32 with enough free space (16MB per dump)

Board Revisions

COK-001, COK-002, SEM-001

These are the earliest revisions of the PS3 motherboard (CECHA, CECHB, CECHC, CECHE, CECHG) and contain 2 x Samsung K9F1G08U0A-PIB0 128MB NAND Chips for a total of 256MB. These chips are interleaved which is controlled by a proprietary controller chip codenamed "Starship2" or SS2. This chip handles the interleaving and presents the NAND Chips to the South Bridge as a single large coherent NOR Chip.

DIA-001, DIA-002

These boards were the first to get the NOR flash memory from the middle revisions of the PS3 (CECHH, CECHJ, CECHK). Only a single Spansion S29GL128N90TFIR2 16MB NOR flash chip is used and the Starship2 chip has been completely removed. The 128N is JEDEC CFI compliant and organized as 8,388,608 words or 16,777,216 bytes, addressable as 16-bit words (PS3 modus operandi) and 8-bit / 1 byte when the BYTE# signal is logic zero.

VER-001

Used in the last revisions of the fatter model PS3 (CECHL, CECHM, CECHP, CECHQ), again with the single Spansion S29GL128N90TFIR2 16MB NOR flash with the exception of the CECHL which used a Samsung K8Q2815UQB-P14B 16MB NOR flash.

JSD-001

This is the pinout originally supplied by Marcan for a CECH-2504A, Points match those taken from a CECH-2504B slim console. Most slims may carry this arrangement.

Pinout Gallery

• 

  Starship2 NOR/EBUS Testpoints (NAND board)

• 

  COK-001 NOR Testpoints (NAND board - only overlay)

• 

  COK-001 NOR Testpoints (NAND board)

• 

  DIA-001 NOR Testpoints

• 

  VER-001 NOR Testpoints

• 

  DYN-001 NOR Testpoints

• 

  JSD-001 NOR Testpoints

• 

  JSD-001 Testpoints (orig. marcan/noraliser)

• JTP-001 - 1-882-481-21-testpoints.jpg

  JTP-001 NOR Testpoints (not mapped)

• 

  SUR-001 Nor Testpoints (not mapped yet)

• 

  NOR Flash general pinout + 50pin ZIF pinout (Progskeet))

• Ver-001 nor.jpg

  VER-001 NOR Testpoints (trisaster.de, missing TRISTATE)

Missing / requested :

• COK-002 (NAND)
• COK-002W (NAND)
• SEM-001 (NAND)
• DIA-002 (NOR)
• SUR-001 (NOR) some difference in components of JSD-001 but the testpoints are the same as JSD-001
• JTP-001 (NOR) visually the same as JSD-001, confirmed working with JSD-001 layout
• KTE-001 (NOR)

Generic wire reference

Wire thickness AWG/mm :

   18 AWG - 0.0403" / 1.024mm
   19 AWG - 0.0359" / 0.912mm
   20 AWG - 0.0320" / 0.812mm
   21 AWG - 0.0285" / 0.723mm
   22 AWG - 0.0253" / 0.644mm
   23 AWG - 0.0226" / 0.573mm
   24 AWG - 0.0201" / 0.511mm
   25 AWG - 0.0179" / 0.455mm
   26 AWG - 0.0159" / 0.405mm
   27 AWG - 0.0142" / 0.361mm
   28 AWG - 0.0126" / 0.321mm
   29 AWG - 0.0113" / 0.286mm
   30 AWG - 0.0100" / 0.255mm
   31 AWG - 0.00893" / 0.227mm
   32 AWG - 0.00795" / 0.202mm
   33 AWG - 0.00708" / 0.180mm
   34 AWG - 0.00631" / 0.160mm
   35 AWG - 0.00562" / 0.143mm
   36 AWG - 0.00500" / 0.127mm
   37 AWG - 0.00445" / 0.113mm
   38 AWG - 0.00397" / 0.101mm7
   39 AWG - 0.00353" / 0.0897mm
   40 AWG - 0.00314" / 0.0799mm
  
   PATA/floppy 40-conductor cable - AWG28 (0.0126" / 0.321mm) with 0.0333" pitch +/- 0.002"
   PATA/floppy 40-conductor cable - AWG30 (0.0100" / 0.255mm) with 0.0333" pitch +/- 0.002"
  
   PATA 80-conductor cable - AWG30 (0.0100" / 0.255mm) with 0.025" pitch +/- 0.0016"
   PATA 80-conductor cable - AWG30 (0.0100" / 0.255mm) with 0.025" pitch +/- 0.002"
   PATA 80-conductor cable - AWG31 (0.00893" / 0.227mm) with 0.025" pitch +/- 0.002"
   PATA 80-conductor cable - AWG32 (0.00795" / 0.202mm) with 0.025" pitch +/- 0.002"

For wiring, use 20-26 AWG. 18 can be too stiff while 28 is too fragile. 24 AWG works fine in most cases. The Ground and VCC wires may ofcourse be thicker than the signal wires. Keep wires short (~20cm).

Generic unresolved issues

1. (user:sel99) : CECHG / SEM-001 - 1-875-384-31 - can dump both NANDs fine, have trouble writing - both with Infectus and Progskeet. Boards below CECHG / SEM-001 flash fine. Others having the same issues?

Progskeet QA/problem solving

Generic advice

Be up to date

Always make sure you used the latest diagrams, drivers and flasher software from progskeet.com

No shorts

Before doing anything, make 100% sure you wired up everything correct (no address/data IO lines mixed? all controllines hooked up? power/ground in order? etc.) and no shorts are made where there should not.

Error : libusb0.dll or libusb0.sys not found

The libusb-win32 Kernel Driver needed for the the flasher to get access to the USB port was not installed. Make sure you unpacked the drivers_xxxxxx file and installed the Progskeet driver (VendorID:1988 / ProductID:0001 in case you need it).

Error : side-by-side configuration is incorrect

In case of "the application has failed to start because its side-by-side configuration is incorrect" make sure Microsoft Visual C 9.0 runtime is installed and "Windows Installer" is not disabled (set to manual or automatic) in Services.msc

Error : incorrect parameter

Make sure you selected the correct values for your NOR/NAND device. E.g. :

• NOR
  • Spansion NOR: 128KB sector, 128 sectors
  • Samsung NOR: 4KB sector, 4096 sectors
• NAND: select Big Block, select Raw, Pages per block: 64, blocks: 1024