Template:CSW-001 pinout: Difference between revisions
Jump to navigation
Jump to search
m (Im not sure if pad #N9 in mullion syscons is an output or an input... i guess is an output, but i remember zecoxao was speculating that it could be an input :) |
mNo edit summary |
||
| Line 7: | Line 7: | ||
| 1 || GND || GND || GND | | 1 || GND || GND || GND | ||
|- | |- | ||
| 2 || SW_PWM (SYSCON) || ? || FREQ<br>Intended to send a [https://en.wikipedia.org/wiki/Pulse-width_modulation PWM] signal to the switch board ? (syscon pad #N9, output ?) | | 2 || SW_PWM ([[Template:Syscon_pinout_BGA_200_pads|SYSCON]]) || ? || FREQ<br>Intended to send a [https://en.wikipedia.org/wiki/Pulse-width_modulation PWM] signal to the switch board ? (syscon pad #N9, output ?) | ||
|- | |- | ||
| 3 || RMC_IN (SYSCON) || ? || <abbr title="missing resistor>NC</abbr><br>Intended to reset syscon (syscon pad #R10, input)<br>Also connected to [[Service Connectors#CN4009]] pin #17 | | 3 || RMC_IN ([[Template:Syscon_pinout_BGA_200_pads|SYSCON]]) || ? || <abbr title="missing resistor>NC</abbr><br>Intended to reset syscon (syscon pad #R10, input)<br>Also connected to [[Service Connectors#CN4009]] pin #17 | ||
|- | |- | ||
| 4 || /POW_SW (SYSCON) || ? || /POWER_SW | | 4 || /POW_SW ([[Template:Syscon_pinout_BGA_200_pads|SYSCON]]) || ? || /POWER_SW | ||
|- | |- | ||
| 5 || /EJECT_SW (SYSCON) || ? || /EJECT_SW | | 5 || /EJECT_SW ([[Template:Syscon_pinout_BGA_200_pads|SYSCON]]) || ? || /EJECT_SW | ||
|- | |- | ||
| 6 || POW_LED (SYSCON) || ? || GREEN | | 6 || POW_LED ([[Template:Syscon_pinout_BGA_200_pads|SYSCON]]) || ? || GREEN | ||
|- | |- | ||
| 7 || STBY_LED (SYSCON) || ? || RED | | 7 || STBY_LED ([[Template:Syscon_pinout_BGA_200_pads|SYSCON]]) || ? || RED | ||
|- | |- | ||
| 8 || BD_LED || ? || BLUE | | 8 || BD_LED || ? || BLUE | ||
Revision as of 17:59, 4 December 2021
| Pin | Signal/Connected to | Description | |
|---|---|---|---|
| On Motherboard | On Switch board | ||
| 1 | GND | GND | GND |
| 2 | SW_PWM (SYSCON) | ? | FREQ Intended to send a PWM signal to the switch board ? (syscon pad #N9, output ?) |
| 3 | RMC_IN (SYSCON) | ? | NC Intended to reset syscon (syscon pad #R10, input) Also connected to Service Connectors#CN4009 pin #17 |
| 4 | /POW_SW (SYSCON) | ? | /POWER_SW |
| 5 | /EJECT_SW (SYSCON) | ? | /EJECT_SW |
| 6 | POW_LED (SYSCON) | ? | GREEN |
| 7 | STBY_LED (SYSCON) | ? | RED |
| 8 | BD_LED | ? | BLUE |
| 9 | GND | GND | GND |
| 10 | +5V_EVER | ? | +5V |