Template:Toshiba T6UN6EFG Pinout: Difference between revisions

From PS3 Developer wiki
Jump to navigation Jump to search
m (doublechecked... the SLAVES_RESET signal is connected to all the big IC's (the amount could vary by board model) with the exception of the IC dedicated to power and the sensors)
m (BT pins in the same order than the EEPROM pins... here the pins are ordered... first you select and set the device communications channel, then inputs, then outputs)
Line 38: Line 38:
| 13 || POWER_CTRL ? || || Texas Instruments SN89062, pin 4 in VX4 boards
| 13 || POWER_CTRL ? || || Texas Instruments SN89062, pin 4 in VX4 boards
|-
|-
| 14 || BT_CTRL ?|| || To BT module (ALPS 413A pin 8 in VX4 boards) through <abbr title="33ohm in VX4 boards">resistor</abbr>
| 14 || BT_SELECT ?|| || To BT module (ALPS 413A pin 8 in VX4 boards) through <abbr title="33ohm in VX4 boards">resistor</abbr>
|-
|-
| 15 || BT_UART_DATA ? || || To BT module (ALPS 413A pin 6 in VX4 boards) through <abbr title="47ohm in VX4 boards">resistor network</abbr>
| 15 || BT_UART_RX ? || || To BT module (ALPS 413A pin 6 in VX4 boards) through <abbr title="47ohm in VX4 boards">resistor network</abbr>
|-
|-
| 16 || BT_UART_DATA ? || || To BT module (ALPS 413A pin 9 in VX4 boards) through <abbr title="47ohm in VX4 boards">resistor network</abbr>
| 16 || BT_UART_TX ? || || To BT module (ALPS 413A pin 9 in VX4 boards) through <abbr title="47ohm in VX4 boards">resistor network</abbr>
|-
|-
| 17 || || || To BT module (ALPS 413A pin 7 in VX4 boards)
| 17 || || || To BT module (ALPS 413A pin 7 in VX4 boards)

Revision as of 04:59, 19 August 2017

QFP package, 80pin

  • Submodels:
    • Toshiba T6UN6EFG-001
    • Toshiba T6UN6EFG-002
    • Toshiba T6UN6EFG-003

The pinout below belongs to a Toshiba T6UN6EFG-003 and was traced in a VX4 board. Has not been verifyed if the pinout matches with T6UN6EFG-001 or T6UN6EFG-002 or other boards. It seems the pins can be remapped at bootloder as can be seen in the photos of the PP1 prototype (note the sensors in that photo are connected to pins 77, 78, 79, 80, this doesnt matches with newer dualshocks 3 models). Some people said in most older versions of the controller it was posible to update the controller firmware by USB with a tool that uploads a rom to the controller, this update procedure should be made by using the BT module because all USB connections are managed by it (so in some way it was the BT module the responsible to update the toshiba controller)

Toshiba T6UN6EFG Pinout
[edit]
Pin # Name Port Description
1 GND To ground
2 V_STBY 2.8V Standby. Power for Toshiba T6UN6EFG, EEPROM, Dualshock PS button, and LED's
3 GND To ground
4 V_BATT To battery through resistor
5 V_STBY 2.8V Standby. Power for Toshiba T6UN6EFG, EEPROM, Dualshock PS button, and LED's
6 ACCL_X To acccelerometer X axis through resistor
7 ACCL_Y To acccelerometer Y axis through resistor
8 ACCL_Z To acccelerometer Z axis through resistor
9 GYRO To gyroscope through resistor
10 V_STBY 2.8V Standby. Power for Toshiba T6UN6EFG, EEPROM, Dualshock PS button, and LED's
11 SLAVES_RESET Texas Instruments SN84001 pin 2, and ALPS 413A pin 5 through resistor network in VX4 boards
12 GND To ground
13 POWER_CTRL ? Texas Instruments SN89062, pin 4 in VX4 boards
14 BT_SELECT ? To BT module (ALPS 413A pin 8 in VX4 boards) through resistor
15 BT_UART_RX ? To BT module (ALPS 413A pin 6 in VX4 boards) through resistor network
16 BT_UART_TX ? To BT module (ALPS 413A pin 9 in VX4 boards) through resistor network
17 To BT module (ALPS 413A pin 7 in VX4 boards)
18 To BT module (ALPS 413A pin 14 in VX4 boards)
19 To BT module (ALPS 413A pin 28 in VX4 boards)
20 GND To ground
21 V_STBY 2.8V Standby. Power for Toshiba T6UN6EFG, EEPROM, Dualshock PS button, and LED's
22 GND To ground
23 LED_1 To led 1 cathode through resistor network
24 LED_2 To led 2 cathode through resistor network
25 LED_3 To led 3 cathode through resistor network
26 LED_4 To led 4 cathode through resistor network
27 Not connected ? (for the PS button backlight led in prototypes ?)
28 SM Small Motor + (rumble)
29 BM Big Motor + (rumble)
30 EEPROM_CLOCK EEPROM, pin 6 in VX4 boards
31 EEPROM_SELECT EEPROM, pin 1 in VX4 boards
32 GND To ground
33 V_STBY 2.8V Standby. Power for Toshiba T6UN6EFG, EEPROM, Dualshock PS button, and LED's
34 EEPROM_DATA_IN EEPROM, pin 5 in VX4 boards
35 EEPROM_DATA_OUT EEPROM, pin 2 in VX4 boards
36 POWER_UNK_1 Texas Instruments SN89062, pin 17 in VX4 boards
37 LX_V ? Texas Instruments SN84001, pin 21 in VX4 boards
38 LY_V ? Texas Instruments SN84001, pin 20 in VX4 boards
39 RX_V ? Texas Instruments SN84001, pin 19 in VX4 boards
40 RY_V ? Texas Instruments SN84001, pin 18 in VX4 boards
41 POWER_UNK_2 Texas Instruments SN89062, pin 21 in VX4 boards
42 POWER_UNK_3 Texas Instruments SN89062, pin 5 in VX4 boards
43 POWER_UNK_4 Texas Instruments SN89062, pin 2 in VX4 boards
44 POWER_UNK_5 Texas Instruments SN89062, pin 10 in VX4 boards (and TP8 in VX4 boards)
45 POWER_UNK_6 Texas Instruments SN89062, pin 12 in VX4 boards (and TP9 in VX4 boards)
46 COM_3 COM 3 (Common Line for Digital Dualshock L3 button Dualshock select button Dualshock start button Dualshock R3 button))
47 DU D-Pad UP Button
48 DR D-Pad RIGHT Button
49 DD D-Pad DOWN Button
50 DL D-Pad LEFT Button
51 V_STBY 2.8V Standby. Power for Toshiba T6UN6EFG, EEPROM, Dualshock PS button, and LED's
52 GND To ground
53 L2 Dualshock L2 button
54 L1 Dualshock L1 button
55 Not connected ? (connected to something in PP1 prototype)
56 R2 Dualshock R2 button
57 R1 Dualshock R1 button
58 TRIANGLE Dualshock triangle button
59 CIRCLE Dualshock circle button
60 CROSS Dualshock cross button
61 SQUARE Dualshock square button
62 Not connected ? (connected to something in PP1 prototype)
63 Not connected ? (connected to something in PP1 prototype)
64 SELECT Dualshock select button
65 L3 Dualshock L3 button
66 R3 Dualshock R3 button
67 START Dualshock start button
68 PS Dualshock PS button
69 To a testpoint (TP23 in VX4 boards)... and maybe something more
70 GND To ground
71 GND
72 GND
73 V_STBY 2.8V Standby. Power for Toshiba T6UN6EFG, EEPROM, Dualshock PS button, and LED's
74 Not connected ?
75 COM_1 COM 1 (Common Line for Analog D-Pad LEFT Button D-Pad DOWN Button D-Pad RIGHT Button D-Pad UP Button Dualshock L1 button Dualshock L2 button)
76 COM_2 COM 2 (Common Line for Analog Dualshock square button Dualshock cross button Dualshock circle button Dualshock triangle button Dualshock R1 button Dualshock R2 button)
77 LX Left Stick, X axis Texas Instruments SN84001, pin 25 in VX4 boards
78 LY Left Stick, Y axis Texas Instruments SN84001, pin 24 in VX4 boards
79 RX Right Stick, X axis Texas Instruments SN84001, pin 23 in VX4 boards
80 RY Right Stick, Y axis Texas Instruments SN84001, pin 22 in VX4 boards
Retrieved from "http://www.psdevwiki.com/ps3/index.php?title=Template:Toshiba_T6UN6EFG_Pinout&oldid=45764"