Template:Toshiba T6UN6EFG Pinout: Difference between revisions
Jump to navigation
Jump to search
mNo edit summary |
m (doublechecked... the SLAVES_RESET signal is connected to all the big IC's (the amount could vary by board model) with the exception of the IC dedicated to power and the sensors) |
||
| Line 32: | Line 32: | ||
| 10 || {{cellcolors|#ff9933}} V_STBY || || 2.8V Standby. Power for Toshiba T6UN6EFG, EEPROM, {{padps}}, and LED's | | 10 || {{cellcolors|#ff9933}} V_STBY || || 2.8V Standby. Power for Toshiba T6UN6EFG, EEPROM, {{padps}}, and LED's | ||
|- | |- | ||
| 11 || | | 11 || {{cellcolors|#555555|#ffffff}} SLAVES_RESET || || Texas Instruments SN84001 pin 2, and ALPS 413A pin 5 through <abbr title="47ohm in VX4 boards">resistor network</abbr> in VX4 boards | ||
|- | |- | ||
| 12 || {{cellcolors|#000000|#ffffff}} GND || || To ground | | 12 || {{cellcolors|#000000|#ffffff}} GND || || To ground | ||
Revision as of 04:52, 19 August 2017
QFP package, 80pin
- Submodels:
- Toshiba T6UN6EFG-001
- Toshiba T6UN6EFG-002
- Toshiba T6UN6EFG-003
The pinout below belongs to a Toshiba T6UN6EFG-003 and was traced in a VX4 board. Has not been verifyed if the pinout matches with T6UN6EFG-001 or T6UN6EFG-002 or other boards. It seems the pins can be remapped at bootloder as can be seen in the photos of the PP1 prototype (note the sensors in that photo are connected to pins 77, 78, 79, 80, this doesnt matches with newer dualshocks 3 models). Some people said in most older versions of the controller it was posible to update the controller firmware by USB with a tool that uploads a rom to the controller, this update procedure should be made by using the BT module because all USB connections are managed by it (so in some way it was the BT module the responsible to update the toshiba controller)
| Pin # | Name | Port | Description |
|---|---|---|---|
| 1 | GND | To ground | |
| 2 | V_STBY | 2.8V Standby. Power for Toshiba T6UN6EFG, EEPROM,  , and LED's
| |
| 3 | GND | To ground | |
| 4 | V_BATT | To battery through resistor | |
| 5 | V_STBY | 2.8V Standby. Power for Toshiba T6UN6EFG, EEPROM, , and LED's
| |
| 6 | ACCL_X | To acccelerometer X axis through resistor | |
| 7 | ACCL_Y | To acccelerometer Y axis through resistor | |
| 8 | ACCL_Z | To acccelerometer Z axis through resistor | |
| 9 | GYRO | To gyroscope through resistor | |
| 10 | V_STBY | 2.8V Standby. Power for Toshiba T6UN6EFG, EEPROM, , and LED's
| |
| 11 | SLAVES_RESET | Texas Instruments SN84001 pin 2, and ALPS 413A pin 5 through resistor network in VX4 boards | |
| 12 | GND | To ground | |
| 13 | POWER_CTRL ? | Texas Instruments SN89062, pin 4 in VX4 boards | |
| 14 | BT_CTRL ? | To BT module (ALPS 413A pin 8 in VX4 boards) through resistor | |
| 15 | BT_UART_DATA ? | To BT module (ALPS 413A pin 6 in VX4 boards) through resistor network | |
| 16 | BT_UART_DATA ? | To BT module (ALPS 413A pin 9 in VX4 boards) through resistor network | |
| 17 | To BT module (ALPS 413A pin 7 in VX4 boards) | ||
| 18 | To BT module (ALPS 413A pin 14 in VX4 boards) | ||
| 19 | To BT module (ALPS 413A pin 28 in VX4 boards) | ||
| 20 | GND | To ground | |
| 21 | V_STBY | 2.8V Standby. Power for Toshiba T6UN6EFG, EEPROM, , and LED's
| |
| 22 | GND | To ground | |
| 23 | LED_1 | To led 1 cathode through resistor network | |
| 24 | LED_2 | To led 2 cathode through resistor network | |
| 25 | LED_3 | To led 3 cathode through resistor network | |
| 26 | LED_4 | To led 4 cathode through resistor network | |
| 27 | Not connected ? (for the PS button backlight led in prototypes ?) | ||
| 28 | SM | Small Motor + (rumble) | |
| 29 | BM | Big Motor + (rumble) | |
| 30 | EEPROM_CLOCK | EEPROM, pin 6 in VX4 boards | |
| 31 | EEPROM_SELECT | EEPROM, pin 1 in VX4 boards | |
| 32 | GND | To ground | |
| 33 | V_STBY | 2.8V Standby. Power for Toshiba T6UN6EFG, EEPROM, , and LED's
| |
| 34 | EEPROM_DATA_IN | EEPROM, pin 5 in VX4 boards | |
| 35 | EEPROM_DATA_OUT | EEPROM, pin 2 in VX4 boards | |
| 36 | POWER_UNK_1 | Texas Instruments SN89062, pin 17 in VX4 boards | |
| 37 | LX_V ? | Texas Instruments SN84001, pin 21 in VX4 boards | |
| 38 | LY_V ? | Texas Instruments SN84001, pin 20 in VX4 boards | |
| 39 | RX_V ? | Texas Instruments SN84001, pin 19 in VX4 boards | |
| 40 | RY_V ? | Texas Instruments SN84001, pin 18 in VX4 boards | |
| 41 | POWER_UNK_2 | Texas Instruments SN89062, pin 21 in VX4 boards | |
| 42 | POWER_UNK_3 | Texas Instruments SN89062, pin 5 in VX4 boards | |
| 43 | POWER_UNK_4 | Texas Instruments SN89062, pin 2 in VX4 boards | |
| 44 | POWER_UNK_5 | Texas Instruments SN89062, pin 10 in VX4 boards (and TP8 in VX4 boards) | |
| 45 | POWER_UNK_6 | Texas Instruments SN89062, pin 12 in VX4 boards (and TP9 in VX4 boards) | |
| 46 | COM_3 | COM 3 (Common Line for Digital     ))
| |
| 47 | DU | 
| |
| 48 | DR | 
| |
| 49 | DD | 
| |
| 50 | DL | 
| |
| 51 | V_STBY | 2.8V Standby. Power for Toshiba T6UN6EFG, EEPROM, , and LED's
| |
| 52 | GND | To ground | |
| 53 | L2 | 
| |
| 54 | L1 | 
| |
| 55 | Not connected ? (connected to something in PP1 prototype) | ||
| 56 | R2 | 
| |
| 57 | R1 | 
| |
| 58 | TRIANGLE | 
| |
| 59 | CIRCLE | 
| |
| 60 | CROSS | 
| |
| 61 | SQUARE | 
| |
| 62 | Not connected ? (connected to something in PP1 prototype) | ||
| 63 | Not connected ? (connected to something in PP1 prototype) | ||
| 64 | SELECT |
| |
| 65 | L3 |
| |
| 66 | R3 |
| |
| 67 | START |
| |
| 68 | PS |
| |
| 69 | To a testpoint (TP23 in VX4 boards)... and maybe something more | ||
| 70 | GND | To ground | |
| 71 | GND | ||
| 72 | GND | ||
| 73 | V_STBY | 2.8V Standby. Power for Toshiba T6UN6EFG, EEPROM, , and LED's
| |
| 74 | Not connected ? | ||
| 75 | COM_1 | COM 1 (Common Line for Analog )
| |
| 76 | COM_2 | COM 2 (Common Line for Analog )
| |
| 77 | LX |  Texas Instruments SN84001, pin 25 in VX4 boards
| |
| 78 | LY |  Texas Instruments SN84001, pin 24 in VX4 boards
| |
| 79 | RX |  Texas Instruments SN84001, pin 23 in VX4 boards
| |
| 80 | RY |  Texas Instruments SN84001, pin 22 in VX4 boards
|