E3

placeholder for E3 (someone with an E3 could use this page for posting E3 info/guides)

E3 Flasher

E3 Flasher - TOP

E3 Flasher - BACK

For some persons who'd like to install E3FLASHER, there are some tutorials on the web,

French tuto: [[1]On PS3-INFO.FR] Made by PsYkOkNaRf

And what I call "THE SUPER UNBRICK MODE": [[2]On PS3-ADDICT.FR]

If you find other tutorials, specify the language

How to make a nor backup

1. place a blank micro SD card into the e3 flasher and use the following settings: switches 1 & 2 should be down, switch 3 should be in the up position, switches 4, 5 & 6 should also be down.
2. while in the xmb press the start button on the flasher and backup process will begin, you will see each light progess on the indicator from 0% to 100% percent. (once finished the lights will flash alternatively)

checking the nor backups for errors

(remove the micro SD card from the flasher and place the card in your pc)

(if you have updated the flasher or recently purchased one you will see three backups on the microSD card bkpps30.bin, bkpps31.bin & bkpps32.bin and the e3flasher text log file)

Bytereverse them with Flowrebuilder and use Validating flash dumps

KEEP THE OTHER BACKUPS SAFE! just incase you do happen to brick your console you might have a chance for recovery..

E3 Nor dump checker

E3 Nor Dump Checker V1.0.exe (521.7 KB)
Article: http://www.ps3hax.net/2011/11/released-e3-nor-dump-checker-v1-0-released-tested/

Quick bulletproof test

does not test:

• bootldr (corrupted binary not detected)
• metldr (corrupted binary not detected)
• bootldr size (both under- and oversize not detected)
• metldr size (both under- and oversize not detected)
• cISD (didn't catch brick-byte error)
• cCSD (didn't catch brick-byte error)
• trvk_prg0 (didn't catch brick-byte error)
• trvk_prg1 (didn't catch brick-byte error)
• trvk_pkg0 (didn't catch brick-byte error)
• trvk_pkg1 (didn't catch brick-byte error)
• eEID (didn't catch brick-byte error)
• cvtrm (didn't catch brick-byte error)
• CELL_EXTNOR_AREA (didn't catch brick-byte error)

partly test:

• ROS0 (but didn't catch brick-byte error)
• ROS1 (but didn't catch brick-byte error)

does test:

• headerprefix ("00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00")
• header ("00 00 00 00 AC 0F FF E0 00 00 00 00 AD DE EF BE")
• header ("FI.I")
• headersuffix "(FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF")
• filetable ("saceru_eoldare.." etc.)

Conclusion : USELESS, brickdumps will still show as 'valid'.
Recommendation: use Flowrebuilder instead and common sense like mentioned on Hardware flashing page.

Added 22 nov 2011

  New E3 flasher update released, it will backup bios 3 times automatically.
  We suggest user verify those bios with E3 Nor dump checker, to assure the backup bios is no erro. 

Conclusion: Anyone with a flasher (should) know that you can dump it 1 to 1000's times the same bad. Comparing CRC/MD5/SHA1 is not any secure way to validate flash (as mentioned on Hardware flashing). Letting the dumper do it x times, only gives endusers/customers a false sense of reassurance, always a bad idea.

Normal E3 downgrade Process

1. place the e3_downgrade.bin and the bkpps3.bin you made on a micro SD Card.

2. switches 1, 2, 3, 4, 5 should be down and switch 6 (lock/unlock) should be in the up position. while in the xmb press start on the flasher and the programming process will begin you will see each light progess on the indicator from 0% to 100% percent. (once finished the lights will flash alternatively)

3. reboot the console and you should see the connect controller using a USB cable screen (if the console just booted back into the xmb you need to manually patch the backup See. Manual E3 downgrade below)

4. assuming the process was sucessful and you see the connect controller screen switch off the console from the back of the playstation using the switch provided with the e3 kit and place your USB downgrade jig in the port closest to the flasher.

5. switch the console back on using the switch provided then quickly press the power and eject button if sucessful the console should power off automatically. (if not repeat the process)

6. copy the Lv2diag.self & PS3UPDAT.PUP from step 1 downgrade files onto a usb and place the usb in the same port you used for the downgrade jig (closest to the flasher) turn on the console and the downgrade process should begin. once finnished the console will turn off automatically

7. next copy the Lv2diag.self onto the usb and place the usb in the same port you used in the last process switch on the console and it should switch off automatically after a few seconds.

8. power the console back on and you should see the connect the controller screen follow the onscreen instructions.

Manual E3 downgrade v2

E3 dumps are byte reversed, and so must our patches (otherwise we have to reverse, paste the v2 in the REV, reverse back again - using byte reversed patches shortcuts that 'reversing confusion' :P)

Dump the flash with the E3, you will end up with a .bin file (e.g. bkpps3.bin)

Patches to insert for v2 downgrade

http://www.ps3devwiki.com/files/flash/patches/E3%20downgrade/

target area	patch no.	NOR Offset	Paste length	Remarks
ROS0	patch1.REV (7 MB)	0x0C0010	0x6FFFE0	version string 3.55
ROS1	patch1.REV (7 MB)	0x7C0010	0x6FFFE0	same as patch1.REV
trvk_prg0 (0x40000) trvk_prg1 (0x60000) trvk_pkg0 (0x80000) trvk_pkg1 (0xA0000)	rvk-040000.REV (512 KB)	0x40000	0x80000	one big patch overlapping several area's

save file and use that file to flash the ps3. Afterwards, use RogeroV2, or any prepatched PUP that has the lv1/hypervisor syscon hashchecks patched out - or use the TCL from the talk/discussion page to patch one yourself) and reinstall the firmware in service mode like any V2 downgrade.

Note: If you wish to extract an E3 dump: Flowrebuilder can bytereverse and extract the NOR dump for you.

To flash a manually patched backup put all the switches on the flasher down and pess start while in the XMB

E3 debricking notes

• Requires soldering wire from SBE (solderpad on NOR flatcable) to TRISTATE (NORpoint on PS3 motherboard)
• Make sure you have correct firmware on SD/TF card
• E3 switches set as 1:Flash fun, 2: OFW, 3: Prog, 4: microSD, 5: PS3 Flash, 6: Lock with the console power disconnected.
• Turn on console to restore (progress LEDs will light up one by one and blink if successfully).
• Unplug powercable and set 1:Flash fun down to PS3 Mode and turn on the PS3, if everything went fine, it will now be debricked (remember: in case syscon has 3.56+ hashes, you need prepatched LV1, see downgrader guides).
  

English-E3 FLASHER repair method if console bricked.pdf (424.95 KB)

user experiences

from my experince soldering a wire to the nor tristate point did nothing, try this method instead. manually patch your nor backup. place the patced backup and the e3_downgrade.bin file onto the SD card then put all the switches on the flasher down and hold start and turn on the console. if the console stays on and the flashing process begins when completed after rebooting the console should boot normally on the firmware you were trying to install, if you see two blue flashing lights and the console just turns off try this.. all switches down except the 6th one (lock/unlock) hold start on the flasher and turn on the console providing that the console stays on once finnished flashing DO NOT TURN THE CONSOLE OFF instead put the last switch down and press start again. once finnished reboot and hopefully the console should be back to life.

Error Codes

E3 Flasher Frontpanel

LED Error

number 1 stands for LED Blinking
number 0 stands for LED OFF

Error Codes	Meaning	Remarks
10000100	Failed to initialize Nor in E3	Check pads / clip at E3 board check may not be properly seated
10000101	Failed to read Nor in E3	Check pads / clip at E3 board check may not be properly seated
10000110	Failed to erase Nor in E3	Check pads / clip at E3 board check may not be properly seated
10000111	Failed to write Nor in E3	Check pads / clip at E3 board check may not be properly seated
10001100	Failed to initialize PS3 BIOS	Check pads / clip at PS3 board check may not be properly seated
10001101	Failed to read PS3 BIOS	Check pads / clip at PS3 board check may not be properly seated
10001110	Failed to erase PS3 BIOS	Check pads / clip at PS3 board check may not be properly seated
10001111	Failed to write PS3 BIOS	Check pads / clip at PS3 board check may not be properly seated
01000000	Failed to initialize TF card	SD card not seated properly
01001000	Failed to open TF card	SD card not seated properly
01000100	Failed to read files in TF card	SD card not seated properly
01001100	Failed to write files to TF card	SD card not seated properly
11000000	Wrong settings of switches	check toggle switch - wrong setting
11001000	Wrong PS3 version, not supported at present	Metldr.2 model undowngradable
11000100	Not the right PS3 for this backup	already used e3flasher on 1 console
11001100	Wrong function settings	check toggle switch - wrong setting
11000010	PS3 is operating Nor, E3 Flasher cannot operate at the same time	check toggle switch - wrong setting