Editing Switch boards

= Description =
The [[Switch boards|Switch board]] is a daughterboard where are located the input switches, and some leds for outputs and fireworks

*'''Switch board components'''
**'''Switches''': Power and Eject buttons
**'''Green and Red leds''', all switch board models have them, are needed to show the standby/poweron modes neither the infamous YLOD
**'''Eject led''', this is the only led not controlled by syscon, the line goes to the bluray drive, so is the bluray drive who decides when is lighted on
**'''White backlight leds''', this was added for PS3 slim models with the new design of the buttons (not touch sensitive)
**'''Unknown subcircuit leds''', this seems some kind of experiment that escaped the prototyping table and entered retail production, for some reason exists in some retail PS3 but seems deactivated and partially unpopulated


*'''Switch board circuit overview''' (based on how [[HSW-001]] works, this could be different for other switch board models)
**When Power or Eject switches are pressed the correlating syscon pins are pulled down (grounded)
**All LED's have its own resistor with a different value to control the current (thus light intensity) and one or more diodes to protect the circuit
**The LED's on the switch board are turned on either by syscon (all them except one) or by the BD drive controller (only the eject blue led) by using an intermediary transistor
**That transistors connects the LED ground pin to ground when the signal to turn them on is sent by syscon or by the BD drive controller (the other pin of the LED is connected permanently to the 5 volts standby line)

= Comparison of functionality =

{| class="wikitable"
|+PS3 retail switch boards
! colspan="2" | PS3 !! colspan="3" | Switch board !! colspan="2" | Switches || colspan="4" | Leds
|-
! [[SKU_Models|PS3 Model]] !! [[Motherboard_Revisions|Motherboard]] !! Model !! Part {{numero}} !! Connector !! Power !! Eject !! Standby/PowerOn/<abbr title="Yellow color is made by lighting red + green leds together">YLOD</abbr> !! Eject !! Switches Backlight !! Board Contour Backlight (factory disabled)
|- 
| colspan="11" {{cellcolors|lightblue}}
|-
| [[CECHAxx]]<BR/>[[CECHBxx]]
| [[COK-001]]
| rowspan="2" | [[CSW-001]] || rowspan="2" | 1-871-871-21 || rowspan="2" | 10 pins || rowspan="2" | Touch sensitive || rowspan="2" | Touch sensitive
| rowspan="2" | 1x <span style="color:#ffffff; background:#ff0000;">red</span> (2 pins)<BR/>1x <span style="color:#ffffff; background:#00ff00;">green</span> (2 pins) || rowspan="2" | 1x <span style="color:#ffffff; background:#0000ff;">blue</span> || rowspan="2" {{no}} || rowspan="2" {{no}}
|-
| [[CECHCxx]]<BR/>[[CECHExx]]
| [[COK-002]]
|-
| [[CECHGxx]]
| [[SEM-001]]
| colspan="3" rowspan="4" {{cellcolors|lightgrey}} Integrated on motherboard || rowspan="4" | Touch sensitive || rowspan="4" | Touch sensitive
| rowspan="4" | 1x <span style="color:#ffffff; background:#ff0000;">red</span> (2 pins) ?<BR/>1x <span style="color:#ffffff; background:#00ff00;">green</span> (2 pins) ? || rowspan="4" | 1x <span style="color:#ffffff; background:#0000ff;">blue</span> || rowspan="4" {{no}} || rowspan="4" {{no}}
|- 
| [[CECHHxx]]
| [[DIA-001]]
|- 
| [[CECHJxx]]<BR/>[[CECHKxx]]
| [[DIA-002]]
|- 
| [[CECHLxx]]<BR/>[[CECHMxx]]<BR/>[[CECHPxx]]<BR/>[[CECHQxx]]
| [[VER-001]]
|- 
| colspan="11" {{cellcolors|lightblue}}
|-
| [[CECH-20xx]]
| [[DYN-001]]
| [[DSW-001]] || 1-880-056-11 || 10 pins || Pressure || Pressure
| 1x <span style="color:#ffffff; background:#ff0000;">red</span>/<span style="color:#ffffff; background:#00ff00;">green</span> (dual, 4 pins) || 1x <span style="color:#ffffff; background:#0000ff;">blue</span> || 2x <span style="color:#000000; background:#ffffff;">white</span> (power)<BR/>2x <span style="color:#000000; background:#ffffff;">white</span> (eject) || {{cellcolors|grey|lightgrey}} 1x <span style="color:#ffffff; background:#ff0000;">red</span> (left-top). 1x <span style="color:#ffffff; background:#0000ff;">blue</span> (right-top)<BR/>1x <span style="color:#ffffff; background:#0000ff;">blue</span> (left-bottom). 1x unpopulated (right-bottom)
|-
| [[CECH-21xx]]
| [[SUR-001]]
| rowspan="2" | [[HSW-001]] || rowspan="2" | 1-881-946-11<BR/>1-881-946-21 || rowspan="2" | 10 pins || rowspan="2" | Pressure || rowspan="2" | Pressure
| rowspan="2" | 1x <span style="color:#ffffff; background:#ff0000;">red</span>/<span style="color:#ffffff; background:#00ff00;">green</span> (dual, 4 pins) || rowspan="2" | 1x <span style="color:#ffffff; background:#0000ff;">blue</span> || rowspan="2" | 2x <span style="color:#000000; background:#ffffff;">white</span> (power)<BR/>2x <span style="color:#000000; background:#ffffff;">white</span> (eject) || rowspan="2" {{cellcolors|grey|lightgrey}} 1x <span style="color:#ffffff; background:#ff0000;">red</span> (left-top). 1x unpopulated (right-top)<BR/>1x <span style="color:#ffffff; background:#0000ff;">blue</span> (left-bottom). 1x unpopulated (right-bottom)
|-
| [[CECH-25xx]]
| [[JTP-001]]<BR/>[[JSD-001]]
|-
| [[CECH-30xx]]
| [[KTE-001]]
| [[KSW-001]] || 1-884-751-31 || 6 pins || Pressure || Pressure
| 1x <span style="color:#ffffff; background:#ff0000;">red</span>/<span style="color:#ffffff; background:#00ff00;">green</span> (dual, 4 pins) || {{no}} || {{no}} || {{no}}
|- 
| colspan="11" {{cellcolors|lightblue}}
|-
| rowspan="1" | SuperSlim
| [[MSX-001]]<BR/>[[MPX-001]]<BR/>[[NPX-001]] ?<BR/>[[PPX-001]] ?<BR/>[[PQX-001]] ?<BR/>[[RTX-001]] ?
| [[MSW-001]] || 1-886-929-11 || 6 pins || Pressure || {{no}}
| 1x <span style="color:#ffffff; background:#ff0000;">red</span>/<span style="color:#ffffff; background:#00ff00;">green</span> (dual, 4 pins) || {{no}} || {{no}} || {{no}}
|-
|}

*Notes
**Boardmodel naming seems thus first letter of SKU motherboard (C=COK, D=DYN, K=KTE, M=MSX/MPX) + "SW-001" ''(with the exception of HSW-001<!--HSW-001 should be related with SUR-001... or there is an easter egg in between DYN-001 and SUR-001-->)''

= Retail Switch boards Models =

== CSW-001 ==

<gallery>
File:Power Eject board CSW-001 (PCB top view).jpg|Switch board CSW-001 (PCB top view)
File:Power Eject board CSW-001 (PCB bottom view).jpg|Switch board CSW-001 (PCB bottom view)
</gallery>

== DSW-001 ==
{| class="wikitable sortable"
|+DSW-001 Pinout  above top panel view port behind pcb. resistors was not tested.
! rowspan="2" | Pin !! colspan="2" | Signal/Connected to !! rowspan="2" | Description
|-
! On Motherboard<!--// <BR />(Syscon [[SW2-30x]] pins)  //-->  !! On Switch board
|-
| 1 || style="color:white; background-color:green;" | pin13 @ Syscon || style="color:white; background-color:green;" | Pogo Pin || style="color:white; background-color:green;" | Only This line have pogo pin @ switchboard, seems that it is a service pin.
|-
| 2 || style="color:white; background-color:darkgrey;" | pin12 @ Syscon || 4x CONTOUR LEDs || Not used by default.<br />On Switch board is connected to a transistor driving 3 LEDs  TWO BLUE AND ONE RED.
|-
| 3 || pin11 @ Syscon || 4x WHITE LEDs|| Inner light for power and eject switches.
|-
| 4 || pin110 @ Syscon || POWER switch || Sink to ground to activate.
|-
| 5 || pin111 @ Syscon || EJECT switch || Sink to ground to activate.
|-
| 6 || pin5 @ Syscon || GREEN led || Connects to bottom-left corner pin (green gnd) of dual red/green LED over power switch.
|-
| 7 || pin6 @ Syscon || RED led || Connects to top-left corner pin (red gnd) of dual red/green LED over power switch.
|-
| 8 || pin13 @ BD_Connector || BLUE led || Connects to blue LED over eject switch.
|-
| 9 || style="color:white; background-color:#333333;" | GND || style="color:white; background-color:#333333;" | GND || style="color:white; background-color:#333333;" | Ground
|-
| 10 || style="color:white; background-color:#CC3333;" | VCC || style="color:white; background-color:#CC3333;" | VCC || style="color:white; background-color:#CC3333;" | +5V DC VCC
|-
|}

*Notes:
**Contour leds - the leds are hidden close to the usb port under the main touch panel. none of the hidden Leds are grounded out but, always receives V+ even when in standby ( red light standby ) reason is unknown and has been found even back on first gen models.
**Compatibility with other ps3 models - this board will work with out back white, hidden, eject led, and 10th gnd pin on a 300X model full power eject and red and green led, A KSW-001 Will not work on a 200X model (dsw-001 slot).

<gallery>
File:Power Eject board DSW-001 (top view).jpg|Switch board DSW-001 (top view)
File:Power Eject board DSW-001 (bottom view).jpg|Switch board DSW-001 (bottom view)
File:Power Eject board DSW-001 (PCB top view).jpg|Switch board DSW-001 (PCB top view)
File:Power Eject board DSW-001 (PCB bottom view).jpg|Switch board DSW-001 (PCB bottom view)
File:100 2895 by alchybear-d7w6jqp.jpg|DSW-001 image diagram (reverse numbering)<!--// http://fc04.deviantart.net/fs71/i/2014/234/f/b/100_2895_by_alchybear-d7w6jqp.jpg //-->
</gallery>

== HSW-001 ==
{{HSW-001 pinout}}

== KSW-001 ==
{| class="wikitable sortable"
|+KSW-001 Pinout  above top panel view port behind pcb. resistors was not tested.
! rowspan="2" | Pin !! colspan="2" | Signal/Connected to !! rowspan="2" | Description
|-
! On Motherboard<!--// <BR />(Syscon [[SW2-30x]] pins)  //-->  !! On Switch board
|-
| 1 || || EJECT switch || Sink to ground to activate
|-
| 2 || style="color:white; background-color:#CC3333;" | VCC || style="color:white; background-color:#CC3333;" | VCC || style="color:white; background-color:#CC3333;" | +5V DC VCC
|-
|3 || || POWER switch || Sink to ground to activate
|-
|4 || || RED led || Connects to right-top corner pin (red gnd) of dual red/green LED over power switch,
|-
| 5 || || GREEN led || Connects to top right corner pin (green gnd) of dual red/green LED over power switch, 
|-
| 6|| style="color:white; background-color:#333333;" | GND || style="color:white; background-color:#333333;" | GND || style="color:white; background-color:#333333;" | Ground
|-
|}

*Notes:
**Compatibility with other ps3 models - Can rewire a DSW-001 by matching pins to make it work with out back white, hidden, eject led, and 10th gnd pin on a 300X model full power eject and red and green led functions, A KSW-001 Will not work on a 200X model (dsw-001 slot) not tested on other models. 
<gallery>
File:Power Eject board KSW-001 (top view).jpg|Switch board KSW-001 (top view)
File:Power Eject board KSW-001 (PCB top view).jpg|Switch board KSW-001 (PCB top view)
File:Power Eject board KSW-001 (PCB with ribbon cable, bottom view).jpg|Switch board KSW-001 (PCB with ribbon cable, bottom view)
File:Power Eject board KSW-001 (PCB bottom view).jpg|Switch board KSW-001 (PCB bottom view)
File:100 2894 by alchybear-d7w6jim.jpg|KSW-001 pin out diagram<!--// http://fc08.deviantart.net/fs71/i/2014/234/2/5/100_2894_by_alchybear-d7w6jim.jpg //-->
</gallery>

== MSW-001 ==

<gallery>
File:Power Eject board MSW-001 (PCB top view).jpg|Switch board MSW-001 (PCB top view)
File:Power Eject board MSW-001 (PCB bottom view).jpg|Switch board MSW-001 (PCB bottom view)
</gallery>

= Flex Ribbon cables =

<gallery>
File:Power Eject Flex Ribbon Cable (PS3 1000 series, top view).jpg|Switch board Flex Ribbon Cable (PS3 1000 series, top view)
File:Power Eject Flex Ribbon Cable (PS3 1000 series, bottom view).jpg|Switch board Flex Ribbon Cable (PS3 1000 series, bottom view)
File:Power Eject Flex Ribbon Cable (PS3 2000 series, top view).jpg|Switch board Flex Ribbon Cable (PS3 2000 series, top view)
File:Power Eject Flex Ribbon Cable (PS3 3000 series, top view).jpg|Switch board Flex Ribbon Cable (PS3 3000 series, top view)
File:Power Eject Flex Ribbon Cable (PS3 3000 series, bottom view).jpg|Switch board Flex Ribbon Cable (PS3 3000 series, bottom view)
</gallery>

= Modding =

== Contour backlight in PS3 2000 Series boards ==
PS3 2000 series ([[CECH-20xx]], [[CECH-21xx]], and [[CECH-25xx]], with Switch boards DSW-001 and HSW-001) has been designed to have a lighted line all around the top edge of the Switch board

'''Light rays bouncing surfaces, and light reactive materials'''
<div style="float:right">[[File:Power Eject board PS3 2000 series (light rays schematic in contour leds).jpg|500px|thumb|left|Switch board PS3 2000 series<BR />Light rays schematic in contour leds]]</div>

The plastic plate uses a "light reactive" material along the edge and in a squared hole in the corner allows the light to "transpass" it

The ligth rays "bounces" inside this material, and the first bouncing surface over the squared hole is a plane at 45 degrees angle. This first bounce aligns the light rays in paralell to the board, the next bounces happens all along the curved surface in horizontal

The reflection of this surfaces can be increased a bit with chrome stickers (or alluminium tape). The case has a plane border of 3,5mm x 17,7cm perfect to stick in it, this way the glue layer of the sticker is at the other side, but the case doesnt have the 45 degrees surface (it has a weird hole instead), you can use other colors for the sticker/s because the color is partially visible from outside (preferably lighter colors or one that matches your led/s color to enhance it)
<BR />
<BR />
<BR />
<BR />
<BR />
<BR />
<BR />
<BR />

=== HSW-001 ===
See [[HSW-001]]

=== DSW-001 Contour backlight ===
*Enabling contour LEDs in DSW-001 Switch board: [http://ps3gunz.org/forum/viewtopic.php?pid=590435 | Original thread (french)] [http://translate.google.com/translate?sl=fr&tl=en&js=n&prev=_t&hl=es&ie=UTF-8&u=http%3A%2F%2Fps3gunz.org%2Fforum%2Fviewtopic.php%3Fpid%3D590435&act=url | Google translated (english)]

== Other links related ==
*HSW-001 pinout schematic: http://www.ps3hax.net/showthread.php?p=544479#post544479
*Contour leds tests video: http://www.youtube.com/watch?v=leapBkrm5tk

{{Components}}<noinclude>[[Category:Main]]</noinclude>