Editing SC EEPROM

Most of the information we have about the sc eeprom comes from graf_chokolo reverse engineering of the HV see [[Hypervisor Reverse Engineering]] 

Here is where system flags, tokens and hashes are stored.

Right now most of the communication we have with the sc eeprom is through Linux using graf_chokolo ps3dm-utils and/or using his payloads.

See also {{talk}} page and [[User_talk:Zer0Tolerance|Zer0Tolerance]]

= SC EEPROM Info =
SC EEPROM from fat consoles is a custom/proprietary EEPROM chip that uses a special non standard commands to read/write from EEPROM.
We are so lucky that Sony had exposed EEROM chip legs out of Syscon, so we have a physical access to it and we could attach devices like "'''Logic Analyzer'''", "'''Protocol Analyzer'''", "'''Custom made MCU boards'''" to capture traffic between console and Syscon EEPROM.

For FAT console Syscon EEPROM consists of: 0x4000 blocks, and every block is consists of 2 bytes of data.
So the total EEPROM size is: 0x8000 byte length.

And since the pin-out of Syscon chip for Slim & Super Slim consoles is not known till now, we can not be sure if the Syscon EEPROM pins are exposed outside or not so we can access it like in FAT console without handling Syscon it self.

== SC EEPROM Commands ==

FAT console's SC EEPROM used a standard SPI protocol with a proprietary commands as flow:

{| class="wikitable"
|-
! Description!! Command !! Note
|-
| Unlock Command || 0xA3 0x00 0x00 || This command must be send first before write command.
|-
| Write Command || 0xA4 0xXX 0xXX || XX XX is a block id to be written (value 0x0000 to 0x3FFF), the maximum data to be written in one command cycle is 32 byte length (16 blocks).
|-
| Read Command || 0xA8 0xXX 0xXX || XX XX is a block id to be read (value 0x0000 to 0x3FFF), there is no maximum limit for read command so we can send it once with block id 0x00 0x00 then read the full EEPROM at once without sending read command again.
|-
| Check Status Command || 0xA9 0x00 0x00 0x00 || The response of this command is 0xFFFFFFFF if there is no error, or any other value if there is error happened or EEPROM still busy doing something.
|}

= SC EEPROM dumps =
* https://mega.co.nz/#!Bt8klAhQ!-t5YVetoL9gz6iZucpqQB9Vl9chCkbhFiMfqjbmotoc {{MD5|B0E0551116B718A4921757B2B074693F}}
* https://mega.co.nz/#!B51wWJYA!zg8O-vCvRBOgK5mpzTQ1H2hgBZmykglmbksB5w1Mlfg {{MD5|3E0E73DACF7E10F2369624EA439C661B}} (partial: {{MD5|7E2BAD4DFDEE485494C8749B1C3E5676}} / {{MD5|05D9ED4B545C709C9C4564F047028DE8}})
* https://mega.co.nz/#!t50DCIiL!RYLvjm35nmH3JVfhsGIXFWVHxmCr07ERsFBWhAOxD_Q {{MD5|95DDFB21D65E38F20CD66517B67EAE7F}}
* https://mega.co.nz/#!x4V0XBgJ!inxGYA5s8lfAF5Pe-naKCzTa1r5pY8Pn18js3D7QlnI

* https://mega.nz/#!iV0nGY4I!94ByAd-sourgK8_l_4s-6BX_V7iVOrysQd55bI0N6ws {{MD5|1DB1CAA8E3D54256A59D08B6AF2B9BC5}} (Dumped by Syscon EEPROM Flasher done by me "'''Abkarino'''" using Arduino Mega).

different consoles, same initial 16 bytes. maybe key/iv?

=Important Offsets=

== EEPROM Offset Table - Flags and Tokens ==

Here is the table of EEPROM offsets that can be accessed through Update Manager (3.15): 

{| class="wikitable FCK__ShowTableBorders"
|-
! Offset !! Size !! Description
|-
| 0x02F00 || 8 || Downgrade Minimum Version String
|-
| 0x02F08 || 0x10 || Downgrade Minimum Version Build + Date Build String
|-
| 0x02F20 || 8 || [[Target ID]]? (HV bible lists the Target ID as 85 Europe, not 83 Japan)
|-
| 0x02F28 || 0xD0 || Padding/undocumented
<pre>00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 
FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 
FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 
FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 
FF FF FF FF FF FF FF FF FF FF FF FF FF FF xx xx 
xx xx xx FF FF xx xx xx xx xx xx xx xx xx xx xx 
xx xx 00 00 00 00 FF xx 00 xx xx FF FF FF FF FF 
FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 
FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 
FF FF FF FF FF FF FF FF FF FF FF xx xx xx 00 00 
xx xx xx xx xx FF FF FF xx xx xx FF FF FF xx 00 </pre>
|-
| 0x02FF8 || 1 || Factory Bit (0 = ?, 1 = reset, 2 = ?, 3 = (on retails))
|-
| 0x02FF9 || 0x7 || Padding/undocumented
<pre>00 00 00 00 xx xx xx </pre>
|-
|}



{| class="wikitable FCK__ShowTableBorders"
|-
! colspan="2" | Offset !! Size !! Description
|-
| colspan="2" | 0x48000 || 0x13 || (lv0 NVS region 0 start) 
|-
| <abbr title="lv0 NVS region 0: 0x48000-0x48012"><small>0</small></abbr> || 0x48000 || 0x13 || (lv0 NVS region 0)
|-
| colspan="2" | 0x48012 || - || (lv0 NVS region 0 end)
|-


| colspan="2" | 0x48013 || 0x2A || QA Token ECDSA Signature (=&gt; 3.60 firmwares)
|-


| colspan="2" | 0x48800 || 0x0C || (lv0 NVS region 1 start) 
|-
| rowspan="3" | <abbr title="lv0 NVS region 1: 0x48800-0x4880B"><small>1</small></abbr> || 0x48802 || 1 || 
|-
| 0x48804 || 4 || bootrom failure code 
|-
| 0x48808 || 4 || bootrom failure timestamp 
|-
| colspan="2" | 0x4880B || - || (lv0 NVS region 1 end)
|-


| colspan="2" | 0x48C00 || 0x20 || (lv0 NVS region 2 start) 
|-
| rowspan="19" | <abbr title="lv0 NVS region 2: 0x48C00-0x48C1F"><small>2</small></abbr> || 0x48C00 || 1 || load_image_in_rom flag (os_boot_order_flag) 
|-
| 0x48C01 || 1 || (force standalone mode related) 
|-
| 0x48C02 || 1 || debug interface (select_net_device) 
|-
| 0x48C03 || 1 || sys.dbgcard.dgbe.index (select_dgbe_device) 
|-
| 0x48C05 || 1 || update_flag for CEB
|-
| 0x48C06 || 1 || FSELF Control Flag / toggles release mode (fself_ctrl)
|-
| 0x48C07 || 1 || Product Mode (UM allows to read this offset, it can be also written but only when already in product mode)
|-
| 0x48C08 || 1 || (UNKNOWN {{unkn|debug}}))
|-
| 0x48C0A || 1 || QA Flag
|-
| 0x48C0B || 1 || mode_auth_flag / gx enable
|-
| 0x48C0C || 1 || bootrom diagnostic mode and parameter
|-
| 0x48C0D || 1 || 
|-
| 0x48C0F || 2 || 
|-
| 0x48C11 || 1 || bootrom trace level (0x00: fatal errors, 0x01: errors, 0x02: information messages, 0x03: debug messages)
|-
| 0x48C12 || 1 || 
|-
| 0x48C13 || 1 || Device Type (flash_ext_format)
|-
| 0x48C14 || ? || cellos_spu_configure
|-
| 0x48C18 || 4 || System Language [[XRegistry.sys#Settings]] ( /setting/system/language )
|-
| 0x48C1C || 4 || VSH Target (seems it can be 0xFFFFFFFE, 0xFFFFFFFF, 0x00000001 default: 0x00000000 /maybe QA,Debug,Retail,Kiosk?)
|-
| colspan="2" | 0x48C1F || - || (lv0 NVS region 2 end)
|-


| colspan="2" | 0x48C22 || 0x03 || (lv0 NVS region 3 start)
|-
| rowspan="3" | <abbr title="lv0 NVS region 3: 0x48C22-0x48C24"><small>3</small></abbr> || 0x48C22 || 1 || be nclk (be_nclck_flag1)
|-
| 0x48C23 || 1 || be ref clk (be_nclck_flag2)
|-
| 0x48C24 || 1 || Bank #0 OS-Flag (ros0 if 0xFF else ros1) (os_bank_indicator)
|-
| colspan="2" | 0x48C24 || - || (lv0 NVS region 3 end)
|-


| colspan="2" | 0x48C25 || 1 || Bank #0 rvkprg-Flag
|-
| colspan="2" | 0x48C26 || 1 || Bank #0 rvkpkg-Flag
|-
| colspan="2" | 0x48C27 || 1 || Bank #1 OS-Flag
|-
| colspan="2" | 0x48C28 || 1 || Bank #1 rvkprg-Flag
|-
| colspan="2" | 0x48C29 || 1 || Bank #1 rvkpkg-Flag
|-


| colspan="2" | 0x48C30 || 0x0D || (lv0 NVS region 4 start)
|-
| rowspan="3" | <abbr title="lv0 NVS region 4: 0x48C30-0x48C3C"><small>4</small></abbr> || 0x48C30 || 1 || SPE number Usally 0x06, can be set to 0x07 to enable the 8 SPE (restrict_spu)
|-
| 0x48C31 || 4 || sata_param
|-
| 0x48C35 || 8 || spr_tbuw_value (cellos_spu_configure)
|-
| colspan="2" | 0x48C3C || - || (lv0 NVS region 4 end)
|-


| colspan="2" | 0x48C40 || 0x10 || (lv0 NVS region 5 start)
|-
| rowspan="6" | <abbr title="lv0 NVS region 5: 0x48C40-0x48C4F"><small>5</small></abbr> || 0x48C42 || 1 || HDD Copy Mode
|-
| 0x48C43 || 4 || 
|-
| 0x48C47 || 1 || Analog Sunset Flag, will disable AACS video output without [[HDMI]] cable soon
|-
| 0x48C50 || 0x10 || Debug Support Flag
|-
| 0x48C60 || 1 || Update Status
|-
| 0x48C61 || 1 || Recover Mode Flag
|-
| colspan="2" | 0x48C4F || - || (lv0 NVS region 5 end)
|-


| colspan="2" | 0x48C80 || 0x10 || (lv0 NVS region 6 start)
|-
| rowspan="2" | <abbr title="lv0 NVS region 6: 0x48C80-0x48C8F"><small>6</small></abbr> || 0x48C80 || 8 || (rsx.rdcy.0)
|-
| 0x48C88 || 8 || (rsx.rdcy.1)
|-
| colspan="2" | 0x48C8F || - || (lv0 NVS region 6 end)
|-


| colspan="2" | 0x48C90 || 0x30 || (lv0 NVS region 7 start)
|-
| rowspan="6" | <abbr title="lv0 NVS region 7: 0x48C90-0x48CBF"><small>7</small></abbr> || 0x48C90 || 8 || (rsx.rdcy.2)
|-
| 0x48C98 || 8 || (rsx.rdcy.3)
|-
| 0x48CA0 || 8 || (rsx.rdcy.4)
|-
| 0x48CA8 || 8 || (rsx.rdcy.5)
|-
| 0x48CB0 || 8 || (rsx.rdcy.6)
|-
| 0x48CB8 || 8 || (rsx.rdcy.7)
|-
| colspan="2" | 0x48CBF || - || (lv0 NVS region 7 end)
|-


| colspan="2" | 0x48CF0 || 0x10 || (NVS region start)
|-
| rowspan="16" | <abbr title="NVS region: 0x48CF0-0x48CFF"><small></small></abbr> || 0x48CF0 || 1 || ss.common.printf.enabled
|-
| 0x48CF1 ||  || 
|-
| 0x48CF2 ||  || 
|-
| 0x48CF3 ||  || 
|-
| 0x48CF4 ||  || 
|-
| 0x48CF5 ||  || 
|-
| 0x48CF6 ||  || 
|-
| 0x48CF7 ||  || 
|-
| 0x48CF8 ||  || 
|-
| 0x48CF9 ||  || 
|-
| 0x48CFA ||  || 
|-
| 0x48CFB ||  || 
|-
| 0x48CFC ||  || 
|-
| 0x48CFD ||  || 
|-
| 0x48CFE ||  || 
|-
| 0x48CFF ||  || 
|-
| colspan="2" | 0x48CFF || - || (NVS region end)
|-


| colspan="2" | 0x48D00 || 0x0C || (lv0 NVS region 8 start)
|-
| rowspan="3" | <abbr title="lv0 NVS region 8: 0x48D00-0x48D0B"><small>8</small></abbr> || 0x48D00 || 4 || ip_addr (dgbe_config)
|-
| 0x48D04 || 4 || ip_netmask
|-
| 0x48D08 || 4 || ip_gateway
|-
| colspan="2" | 0x48D0B || - || (lv0 NVS region 8 end)
|-



| colspan="2" | 0x48D20 || 0x08|| (lv0 NVS region 9 start)
|-
| <abbr title="lv0 NVS region 9: 0x48D20-0x48D27"><small>9</small></abbr> || 0x48D20 || 8 || spider.gbe0.macaddr.0  (<code>0xFFFFFFFFFFFFFFFF</code> if unused/nonpresent)
|-
| colspan="2" | 0x48D27 || - || (lv0 NVS region 9 end)
|-


| colspan="2" | 0x48D28 || 0x18 || (lv0 NVS region B start)
|-
| rowspan="3" | <abbr title="lv0 NVS region B: 0x48D28-0x48D3F"><small>B</small></abbr> || 0x48D28 || 8 || spider.gbe0.macaddr.1  (<code>FFFFFFFFFFFFFFFF</code> if unused/nonpresent)
|-
| 0x48D30 || 8 || spider.gbe0.macaddr.2  (<code>FFFFFFFFFFFFFFFF</code> if unused/nonpresent)
|-
| 0x48D38 || 8 || spider.gbe0.macaddr.3  (<code>FFFFFFFFFFFFFFFF</code> if unused/nonpresent)
|-
| colspan="2" | 0x48D3F || - || (lv0 NVS region B end)
|-



| colspan="2" | 0x48D3E || 0x50 || (lv0 NVS region A start)
|-
| <abbr title="lv0 NVS region A: 0x48D3E-0x48D8D"><small>A</small></abbr> || 0x48D3E || 0x50 || QA Token - UM doesn't allow access to this offset but SC Manager can read/write it (qa_token)
|-
| colspan="2" | 0x48D8D || - || (lv0 NVS region A end)
|-


| colspan="2" | 0x48D8E || 0x50 || mode_auth_data (read/cleared by ss_sc_init_pu, checked by spu_mode_auth)
|-
|}

In a standard mostly untouched ps3 the common value for this flags is 0xFF wich means not active, anything else means active (e.g. 0xFE)

To change this to an active status you have to write 0x00 to turn on the flag

Debug support flag is tied to EID which is supposed to be hashed and saves in SC EEPROM

QA flag is tied to QA token that is also saved in this part of the SC EEPROM

QA Token ECDSA Signature is stored in 0x48013 offset (starting from 3.60 firmwares)

== Undocumented config ==

There is an unknown syscon response of 0x100 bytes when using NVS service with such params: BlockID=1, Offset=0, Size=0.
<pre>
0000h: FF 02 FF FE FF 02 FF FF 19 FB E1 16 00 00 00 00  ÿ.ÿþÿ.ÿÿ.ûá..... 
0010h: 17 74 B8 54 00 00 E1 18 00 04 00 00 0C 03 00 00  .t¸T..á......... 
0020h: 3C 02 02 00 00 00 00 10 00 00 00 00 55 55 55 55  <...........UUUU 
0030h: 00 00 00 00 00 00 00 00 17 E0 C8 52 00 00 E2 18  .........àÈR..â. 
0040h: 01 50 00 35 40 01 03 00 00 00 00 10 1D 30 00 B3  .P.5@........0.³ 
0050h: 00 07 01 00 00 00 00 00 00 00 00 00 00 00 00 00  ................ 
0060h: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF  ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ 
0070h: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF  ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ 
0080h: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF  ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ 
0090h: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF  ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ 
00A0h: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF  ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ 
00B0h: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF  ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ 
00C0h: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF  ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ 
00D0h: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF  ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ 
00E0h: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF  ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ 
00F0h: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF  ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ 
</pre>

This is 0x48800 on EEPROM

cech-c (NO BD Drive): http://pastie.org/private/grl0dc0dxajisa36chgm7w

== lv0 SC EEPROM usage ==
<pre>
[*] lv0 NVS regions:
	# start_offset end_offset block   size
	0 0x00         0x12       0x48000 0x13
	1 0x00         0x0B       0x48800 0x0C
	2 0x00         0x1F       0x48C00 0x20
	3 0x22         0x24       0x48C00 0x03
	4 0x30         0x3C       0x48C00 0x0D
	5 0x40         0x4F       0x48C00 0x10
	6 0x80         0x8F       0x48C00 0x10
	7 0x90         0xBF       0x48C00 0x30
	8 0x00         0x0B       0x48D00 0x0C
	9 0x20         0x27       0x48D00 0x08
	A 0x3E         0x8D       0x48D00 0x50
	B 0x28         0x3F       0x48D00 0x18

[*] Example region data (taken from region cache):
	2:
	   01 FF 05 FF FF FF FF FF FF FF 00 FF FF FF FF FF
	   FF FF FF FE FF FF FF FF 00 00 00 01 00 00 00 00
	3:
	   FF FF 00
	4:
	   06 18 18 17 18 FF FF FF FF FF FF FF FF
	5:
	   FF FF 0D 02 0A 02 FF FF FF FF FF FF FF FF FF FF
	9:
	   FF FF FF FF FF FF FF FF

[*] lv0 SC EEPROM usage:
	name                 addr    size structure
	dgbe_config          0x48D00 0x0C [0x04 ip_addr, 0x04 ip_netmask, 0x04 ip_gateway]
	restrict_spu         0x48C30 0x01 [0x01 flag]
	sata_param           0x48C31 0x04 [0x04 flag]
	os_bank_indicator    0x48C24 0x01 [0x01 flag]
	cellos_spu_configure 0x48C33 0x04 [0x04 config]
	flash_ext_format     0x48C13 0x01 [0x01 flag]
	cellos_flags         0x48C0F 0x02 [0x02 flags]
	qaf_enable           0x48C0A 0x01 [0x01 flag]
	UNKNOWN (debug?)     0x48C08 0x01 [0x01 flag]
	fself_ctrl           0x48C06 0x01 [0x01 flag]
	select_dgbe_device   0x48C03 0x01 [0x01 index]
	os_boot_order_flag   0x48C00 0x01 [0x01 flag]
	qa_token             0x48D3E 0x50 [0x50 token]
	UNKNOWN              0x48804 0x04 [0x04 value]
	UNKNOWN              0x48D20 0x08 [0x08 value]
	rsx.rdcy.7           0x48CB8 0x08 [0x08 value]
	rsx.rdcy.6           0x48CB0 0x08 [0x08 value]
	rsx.rdcy.5           0x48CA8 0x08 [0x08 value]
	rsx.rdcy.4           0x48CA0 0x08 [0x08 value]
	rsx.rdcy.3           0x48C98 0x08 [0x08 value]
	rsx.rdcy.2           0x48C90 0x08 [0x08 value]
	rsx.rdcy.1           0x48C88 0x08 [0x08 value]
	rsx.rdcy.0           0x48C80 0x08 [0x08 value]
	be_nclck_flag2       0x48C23 0x01 [0x01 flag]
	be_nclck_flag1       0x48C22 0x01 [0x01 flag]
	select_net_device    0x48C02 0x01 [0x01 index]
	spr_tbuw_value       0x48C35 0x08 [0x08 value]
	bootrom_trace_level  0x48C11 0x01 [0x01 level]
</pre>

== System Data From EEPROM  ==

Here is the list of possible EEPROM offsets: 

{|class="wikitable"
|-
! Index !! SC EEPROM Offset !! Size Of Data !! Description
|-
| 0 || 0x48D20 || 6 ||?
|-
| 1 || 0x48D28 || 6 ||?
|-
| 2 || 0x48D30 || 6 ||?
|-
| 3 || 0x48D38 || 6 ||?
|-
| 4 || 0x48D00 || 4 ||?
|-
| 5 || 0x48D04 || 4 ||?
|-
| 6 || 0x48D08 || 4 ||?
|}

== Dumpable EEPROM Offset - Block ID and Block Offset Mapping Table (NVS Service) ==

Right now we only have read access to some portions of the eeprom to have access to this regions DM needs to be patched, see section dumping eeprom

{|class="wikitable"
|-
! EEPROM Offset !! Block ID !! Block Offset !! Description !! Physical Offset
|-
| 0x48000 - 0x480FF || 0x00 || 0x48000 - 0x480FF || ? || 0x7000
|-
| 0x48800 - 0x488FF || 0x01 || 0x48800 - 0x488FF || Bluray Drive Area || 0x7100
|-
| 0x48C00 - 0x48CFF || 0x02 || 0x48C00 - 0x48CFF || Contains flags and tokens/ see above || 0x7200
|-
| 0x48D00 - 0x48DFF || 0x03 || 0x48D00 - 0x48DFF || System Data Region || 0x7300
|-
| 0x2F00 - 0x2FFF || 0x10 || 0x2F00 - 0x2FFF || "Industry Area" aka OS Version Area || 0x2F00
|-
| 0x3000 - 0x30FF || 0x20 || 0x3000 - 0x30FF || "CS Area" || 0x3000
|-
| All other offsets || Invalid || Invalid || ? ||
|}

=Dumping your SC EEPROM=

==Linux==

First you need graf_chokolo kernel ps3dm-utils and linux_hv_scripts.

If you are ready.

Patch DM using linux_hv_scripts

<pre>
dmpatch.sh
</pre>

Read the data from the region you want for example (see tables above)

<pre>
ps3dm_scm /dev/ps3dmproxy 0x48000 0xFF
</pre>

You can see some coolstuff that containing dumps

=Hashes=

Where exactly the hashes are stored is still a secret, it is said that those hashes are stored in SC EEPROM

To retrieve the information about the packages you have installed you can also use ps3d_utils

==Linux==

===Installed Package info===

<pre>
ps3dm_um /dev/ps3dmproxy get_pkg_info TYPE
</pre>

Examples
----

get_pkg_info 1 - Core OS package

<pre>	
		0003004100000000
</pre>	
	
get_pkg_info 2 - Revoke List for program

<pre>	
		0003004100000000
</pre>
		
get_pkg_info 3 - Revoke list for package
	
<pre>
		0002003000000000
</pre>
		
get_pkg_info 4
	
<pre>
		deadbeaffacebabe
</pre>
		
get_pkg_info 5
	
<pre>
		deadbeaffacebabe
</pre>

get_pkg_info 6 - Firmware Package
	
<pre>
		0003005000000000
</pre>	


You can find more information about this in [[Hypervisor Reverse Engineering]] 


===Hashes===

What algorithm is used and what exactly is hashed is still unknown (seems that the content of files is hashed by the SHA-1).

<pre>
ps3dm_scm /dev/ps3dmproxy get_region_data ID
</pre>

These hashes are checked by lv1 to make sure that the data has not been altered through [[SC_Manager|SC Manager]]: '''scm_get_region_data: get_result: ret[X]: 0x%x'''

Examples
----


region_data 0 - Core OS package

<pre>
00 03 00 41 00 00 00 00 00 c3 eb 01 96 24 d0 1c 26 14 f3 1c a4 a2 ff ce 81 77 3a 4c f8 42 86 04 ee 34 bb db be 1c a7 51 e5 59 f1 95 61 07 a5 eb 
</pre>

region_data 1

<pre>	
ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
</pre>

region_data 2

<pre>	
ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
</pre>

region_data 3 //Revoke List for program?

<pre>	
00 03 00 41 00 00 00 00 80 41 f6 b8 f2 d5 30 60 59 35 49 d7 f0 3d 58 57 87 00 88 11 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
</pre>

region_data 4

<pre>	
ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff 
</pre>

region_data 5 //Revoke List for package?

<pre>		
00 02 00 30 00 00 00 00 ba 6e 1c d5 5f 48 5b 8b 3f cc c8 60 75 ce f6 83 b2 20 dc f4 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
</pre>

region_data 6

<pre>	
de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be 
</pre>

region_data 7
	
<pre>
de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be 
</pre>

region_data 8 - BD Firmware Package

<pre>	
00 03 00 50 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
</pre>

region_data 9
	
<pre>
de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be 
</pre>

region_data 10

<pre>	
de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be 
</pre>

region_data 11
	
<pre>
de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be 
</pre>

region_data 12
	
<pre>
de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be 
</pre>

region_data 13
	
<pre>
de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be 
</pre>

region_data 14
	
<pre>
de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be 
</pre>

region_data 15
	
<pre>
de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be de ad be af fa ce ba be 
</pre>

region_data 16 - 47?

=Dumped data=

Here is an example of data from syscon which stores VTRM block key, SRK/SRH, region data, etc.

<pre>
0x0000: 00 00 00 03 C0 00 00 FF 00 00 00 00 00 00 00 00  ................ 
0x0010: 01 A2 F6 6C 26 54 1A 54 CE A3 F9 71 50 2B A8 20  ...l&T.T...qP+.  
0x0020: 33 0E F4 5F 77 19 96 A6 7A 84 5D C9 AE B9 50 73  3.._w...z.]...Ps 
0x0030: AE 45 5D 8E 6C BB 80 4D 7E C5 BF A4 AC 8E E1 E5  .E].l..M~....... 
0x0040: 82 9B 0A 57 9A 40 D9 0C 00 00 00 00 00 00 00 00  ...W.@.......... 
0x0050: 7F 03 00 94 B4 7C B6 50 51 E5 84 30 4D 51 77 7C  ....|.PQ..0MQw| 
0x0060: 7C 03 00 94 B4 7C B6 50 51 E5 84 30 4D 51 77 7C  |....|.PQ..0MQw| 
0x0070: 7D 03 00 94 B4 7C B6 50 51 E5 84 30 4D 51 77 7C  }....|.PQ..0MQw| 
0x0080: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF  ................ 
0x0090: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF  ................ 
0x00A0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF  ................ 
0x00B0: 00 03 00 55 00 00 00 00 50 12 F0 AD 3A 4F 9F 1B  ...U....P...:O.. 
0x00C0: F9 F1 E1 D3 64 85 D4 01 19 9D 76 9E 5C 33 8D FE  ....d.....v.\3.. 
0x00D0: 39 75 10 9B 73 43 69 89 2B F6 EE 53 15 4A 3B 06  9u..sCi.+..S.J;. 
0x00E0: 00 03 00 55 00 00 00 00 7B C9 65 97 CF 0D 20 4B  ...U....{.e... K 
0x00F0: BB 6A B1 B9 B0 71 83 27 79 6F 16 08 FF FF FF FF  .j...q.'yo......
------------------------------------------------------------------------- 
0x0100: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF  ................ 
0x0110: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF  ................ 
0x0120: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF  ................ 
0x0130: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF  ................ 
0x0140: 00 01 00 00 00 00 00 00 B0 64 53 92 7F 5E 29 47  .........dS.^)G 
0x0150: 9C BC 84 58 4A F2 ED 0B 50 E1 BE F3 FF FF FF FF  ...XJ...P....... 
0x0160: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF  ................ 
0x0170: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF  ................ 
0x0180: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF  ................ 
0x0190: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF  ................ 
0x01A0: DE AD BE AF FA CE BA BE DE AD BE AF FA CE BA BE  ................ 
0x01B0: DE AD BE AF FA CE BA BE DE AD BE AF FA CE BA BE  ................ 
0x01C0: DE AD BE AF FA CE BA BE DE AD BE AF FA CE BA BE  ................ 
0x01D0: DE AD BE AF FA CE BA BE DE AD BE AF FA CE BA BE  ................ 
0x01E0: DE AD BE AF FA CE BA BE DE AD BE AF FA CE BA BE  ................ 
0x01F0: DE AD BE AF FA CE BA BE DE AD BE AF FA CE BA BE  ................
------------------------------------------------------------------------- 
0x0200: 00 03 00 50 00 00 00 00 00 00 00 00 00 00 00 00  ...P............ 
0x0210: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................ 
0x0220: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................ 
0x0230: DE AD BE AF FA CE BA BE DE AD BE AF FA CE BA BE  ................ 
0x0240: DE AD BE AF FA CE BA BE DE AD BE AF FA CE BA BE  ................ 
0x0250: DE AD BE AF FA CE BA BE DE AD BE AF FA CE BA BE  ................ 
0x0260: DE AD BE AF FA CE BA BE DE AD BE AF FA CE BA BE  ................ 
0x0270: DE AD BE AF FA CE BA BE DE AD BE AF FA CE BA BE  ................ 
0x0280: DE AD BE AF FA CE BA BE DE AD BE AF FA CE BA BE  ................ 
0x0290: DE AD BE AF FA CE BA BE DE AD BE AF FA CE BA BE  ................ 
0x02A0: DE AD BE AF FA CE BA BE DE AD BE AF FA CE BA BE  ................ 
0x02B0: DE AD BE AF FA CE BA BE DE AD BE AF FA CE BA BE  ................ 
0x02C0: DE AD BE AF FA CE BA BE DE AD BE AF FA CE BA BE  ................ 
0x02D0: DE AD BE AF FA CE BA BE DE AD BE AF FA CE BA BE  ................ 
0x02E0: DE AD BE AF FA CE BA BE DE AD BE AF FA CE BA BE  ................ 
0x02F0: DE AD BE AF FA CE BA BE DE AD BE AF FA CE BA BE  ................
------------------------------------------------------------------------- 
0x0300: DE AD BE AF FA CE BA BE DE AD BE AF FA CE BA BE  ................ 
0x0310: DE AD BE AF FA CE BA BE DE AD BE AF FA CE BA BE  ................ 
0x0320: DE AD BE AF FA CE BA BE DE AD BE AF FA CE BA BE  ................ 
0x0330: DE AD BE AF FA CE BA BE DE AD BE AF FA CE BA BE  ................ 
0x0340: DE AD BE AF FA CE BA BE DE AD BE AF FA CE BA BE  ................ 
0x0350: DE AD BE AF FA CE BA BE DE AD BE AF FA CE BA BE  ................ 
0x0360: DE AD BE AF FA CE BA BE DE AD BE AF FA CE BA BE  ................ 
0x0370: DE AD BE AF FA CE BA BE DE AD BE AF FA CE BA BE  ................ 
0x0380: 42 03 00 94 B4 7C B6 50 51 E5 84 30 4D 51 77 7C  B....|.PQ..0MQw| 
0x0390: 43 03 00 94 B4 7C B6 50 51 E5 84 30 4D 51 77 7C  C....|.PQ..0MQw| 
0x03A0: 40 03 00 94 B4 7C B6 50 51 E5 84 30 4D 51 77 7C  @....|.PQ..0MQw| 
0x03B0: 41 03 00 94 B4 7C B6 50 51 E5 84 30 4D 51 77 7C  A....|.PQ..0MQw| 
0x03C0: 46 03 00 94 B4 7C B6 50 51 E5 84 30 4D 51 77 7C  F....|.PQ..0MQw| 
0x03D0: 47 03 00 94 B4 7C B6 50 51 E5 84 30 4D 51 77 7C  G....|.PQ..0MQw| 
0x03E0: 44 03 00 94 B4 7C B6 50 51 E5 84 30 4D 51 77 7C  D....|.PQ..0MQw| 
0x03F0: 45 03 00 94 B4 7C B6 50 51 E5 84 30 4D 51 77 7C  E....|.PQ..0MQw| 
</pre>

== More samples ==

* https://dl.dropboxusercontent.com/u/35197530/bin/eeprom.bin

=Tokens=

Here we will document the different types off tokens known in the PS3
All tokens are tied? encrypted? using EID0.
They enable additional repository nodes.

==List==
{| class="wikitable FCK__ShowTableBorders"
|-
! Token !! Location !! Size !! SPU module !!Description
|-
| qa_token || sc_eeprom - 0x48D3E || 0x50 || spu_token_processor.self || 
|-
| user_token || ? || ? || spu_utoken_processor.self  || Encrypted/Signed
|-
| token_seed || ? || ? || ?  || This is used to create the token with EID0
|}

==Token Seed==

?

==Structure==

This section has to be corrected, is only based on debug strings, we need to decrypt the tokens

===Token Seed===

?

===QA Token===



===User Token===

{| class="wikitable FCK__ShowTableBorders"
|-
! Address !! Size !! Description
|-
| ? || ? || m_magic
|-
| ? || ? || m_format_version
|-
| ? || ? || m_size
|-
| ? || ? || m_capability
|-
| ? || ? || m_expire_date
|-
| ? || ? || m_idps?
|-
| ? || ? || m_attribute
|-
| ? || ? || m_digest
|}

For every atribute in the token

{| class="wikitable FCK__ShowTableBorders"
|-
! Address !! Size !! Description
|-
| ? || ? || attr:m_type
|-
| ? || ? || attr:m_size
|-
| ? || ? || attr:m_data
|}

= Dumping SC EEPROM - hardware way =

{| border="1" cellspacing="0" cellpadding="5" border="#999" class="wikitable" style="border:1px solid #999; border-collapse: collapse;" 
|-
! style="background-color:red;" | <span style="background-color:lightred; color:white; font-size:200%; ">Warning</span>
|-
| style="background-color:white;" | <span style="white; color:red; font-size:150%; text-align:center; ">You can use this method at your own risk. Author is not responsible for any hardware damages and failures. 
|}
== Bus Pirate 3 Solderless method ==

=== You need ===
1) PS3 motherboard with BGA syscon chip (COK001, COK002, SEM001, DIA001, etc)

2) Bus Pirate v3.6 with connectors.

3) Wires (I used AWG32 150mm with tinned ends, see below)

4) PC with OS Windows7 (Should work on other windows systems, but not tested).

5) A sharp pencil.

6) Fingers ;)

=== Hardware Part ===

Find the syscon on your PS3 motherboard.
[[File:CXR713120 on SEM-001.JPG|thumbnail|none]]

Look at the EEPROM Pins location and Draw serifs on the upper surface of the chip, strictly on these pins using pencil.
[[File:CXR713120_EEPROM_PINS.JPG||thumbnail|none]]

Draw the Pinout for convenience.
[[File:CXR713120 EEPROM PINOUT.JPG|thumbnail|none]]

Connect Bus-Pirate and AWG32 wires using probe Kit
[[File:Bus-Pirate-3 with Wires.jpg|thumbnail|none]]

Connect Bus-Pirate to the EEPROM Pins using the folowing table:
{| class="wikitable"
|-
! Bus Pirate pin !! EEPROM pin
|-
| CLK || SKB
|-
| CS || CSB
|-
| MOSI || DI
|-
| MISO || DO
|-
| 3V3 ||  RBB
|-
| GND || Any Ground Point
|}
Use 1 finger to hold the wires. The wires should be well connected with the eeprom pins.
[[File:CXR713120 EEPROM FingerTrick.JPG|thumbnail|none]]
Connect Bus-Pirate to you PC with Windows7 by USB.

=== Software Part ===

Big thanks to '''Dasanko''' for the hard work and for the Syscon Flasher GUI Tool!!!

Download and Install the driver for Bus-Pirate.

Download link: http://www.ftdichip.com/Drivers/CDM/CDM%20v2.12.00%20WHQL%20Certified.exe

Open the Device Manager and find the port number of your USB Serial Port.
[[File:USB Serial Port.jpg|thumbnail|none]]

Download and Run Syscon Flasher.exe

Download link: https://mega.co.nz/#!clljxQgQ!vE93p35DJ9-FMKuxpev3zZvPBnxP_IQscPSXK9ocmH8

MD5=D59A8AA9E7BB1AEB753D7C6391CE17B1

[[File:Syscon Flasher GUI.jpg|thumbnail|none]]

There are 6 simple steps to obtain the dump.

1) Select the correct USB Serial Port for Bus-Pirate.

2) Press "Send settings to device" button. If done correctly, then "Mode" Led on the Bus Pirate will be Green.

3) Press "Power on" button. If done correctly, then "VREG" Led on the Bus Pirate will be Red.

4) Press "Browse" button and specify location and file name for your syscon eeprom dump.

5) Specify Offset and Length. Offset=0 Length=0x8000 for full dump the eeprom.

6) Press "Fast Read" button and wait about 15sec.

Enjoy:

My dump, for example:

https://mega.co.nz/#!E1kHgSZJ!4e7TdNLdkQQzinwlnRO2KmaBd0GeBliHuHFe2tkmBgQ

== Bus Pirate 3 method by: ([[User_talk:Zer0Tolerance|Zer0Tolerance]]) ==

=== You need ===
1) PS3 motherboard. I am using '''DIA-001'''. may be we can dump it from another boards, but it is unknown yet.

2) Device that can work with SPI interface and send any commands. I am using a Bus Pirate v3.6 with connectors.

3) Soldering station.

4) Wires (see below).

5) Personal conputer with installed HxD, Putty (or other terminal supporting serial port connections, e.g.:Tera Term) , Notepad++

6) /dev/Hands ;)

=== Preparation ===

Find the test points on the motherboard using this picture.
[[File:DIA-001 SysCon EPROM Interface.png|thumbnail|none]]

All points are covered with varnish. You need to carefully remove the varnish to the copper and solder the wires to it.

Attach a Bus Pirate to the wires using the following table:
   
{| class="wikitable"
|-
! Bus Pirate pin !! Test Point
|-
| CLK || SKB
|-
| CS || CSB
|-
| MOSI || DI
|-
| MISO || DO
|-
| 3V3 || WCB, RBB
|-
| GND || Any Ground Point
|}

Make sure that the battery is attached to the motherboard.

Plug your Bus pirate to the USB port on your PC using mini_USB_to_USB cable. (I am using the cable from the ps3 gamepad)

It should be done like this, see the following picture:

[[File:Dumping SC EEPROM using Bus Pirate v3.6.JPG|thumbnail|none]]

=== Setup software ===

1) Install the driver for the Bus Pirate and setup your virtual COM port for it using following table:
{| class="wikitable"
|-
! Parameter !! Value
|-
| Bits per second || 115200
|-
| Data bits || 8
|-
| Parity || None
|-
| Stop bits || 1
|-
| Flow control || None
|}

Open Putty and set it up:

session params:

connection type: Serial

Serial line: COM3 (choose your virtual COM port)

Speed (baud rate): 115200

Logging params:

Session logging: All session output

Log file name: click Browse button and specify your logfile, for example: C:\PS3\Logs\logfile.log

Now click Open button and setup mode for bus pirate using following commands:
{| class="wikitable"
|-
! Command !! Description
|-
| m || (mode)
|-
| 5 || (SPI)
|-
| 4 || (Set speed: 1MHz)
|-
| 2 || (Clock polarity: Idle high)
|-
| 1 || (Output clock edge: Idle to active
|-
| 1 || (Input sample phase: Middle *default)
|-
| 2 || (CS: /CS)
|-
| 2 || (Select output type: Normal (H=3.3V, L=GND))
|}

Enable 3.3V: Just type: W (big leter) and press Enter.

=== Obtain the dump ===

Type: [0xa8 0x00 0x00 r:32768] and press Enter.

Wait until dumping process will be completed and close Putty.

Thats all. The dump must be into your logfile.log

You can use Notepad++ and Hex Editor like HxD to convert the dump to binary format.

<small>Read Command is 0xA8 0xXX 0xXX, XX XX is a block id to be read, the full EEPROM is 32768 bytes lenght (0x8000),  [r:] are syntax command of the Bus Pirate for start, read byte and end</small>

== Arduino Mega method by: ([[User_talk:Abkarino|Abkarino]]) == 

  I had build my own Syscon EEPROM flasher based on open source hardware "'''Arduino Mega'''" and some resistors.
This flasher will allow you fully read/write to your Syscon EEPROM (FAT consoles only till now).

=== You need ===
1) PS3 motherboard. I had used '''SEM-0001''' board by desoldering Syscon chip form it but you can use, '''DIA-001''' for example without desoldering Syscon chip since all eeprom pins had a test points in the board it self.

2) Arduino Mega or any Arduino board.

3) 6 x 3.6 KOHM resistors + 6 x 1.8 KOHM resistors (work together as a voltage dividers since Arduino IO logic is 5.0v and Syscon EEPROM IO Logic is 3.3v).

4) Soldering station.

5) Wires & Bread board  (Optional).

6) Any PC that have terminal software like Putty, RealTerm and so on to access serial port, and any Hex Editor like HxD.

=== Preparation ===

Find the test points on the motherboard using this picture.
[[File:DIA-001 SysCon EPROM Interface.png|thumbnail|none]]
Or if you have a very good soldering skills and tools to desolder your SysCon then you can desolder your SysCon and solder your wires to it directly. 

All points are covered with varnish. You need to carefully remove the varnish to the copper and solder the wires to it.

Attach a Arduino Mega to the wires using the following table:
   
{| class="wikitable"
|-
! Arduino Mega pin !! Test Point !! Syscon Pin
|-
| SCL (52) || SKB || E16
|-
| SS (53) || CSB || F16
|-
| MOSI (51) || DI || G16
|-
| MISO (50) || DO || H16
|-
| WP (48) || WCB || J15
|-
| RB (49) || RBB || J16
|-
| VCC (3.3v) || Not needed if you used battery power || G11
|-
| GND || Any Ground Point || C15
|}

Make sure that the battery is attached to the motherboard if you will dump/flash SysCon EEPROM in board.

=== Wiring Diagram & Photos ===

[[File:PS3 SysCon EEPROM Flasher.jpg|thumbnail|none|PS3 SysCon EEPROM Flasher]]
[[File:Fat SysCon Desoldered And Attached To Arduino.jpg|thumbnail|none|Fat SysCon Desoldered And Attached To Arduino]]
[[File:SysCon EEPROM Dumping Process.jpg|thumbnail|none|SysCon EEPROM Dumping Process]]

=== Arduino Sketch Source Code ===
Here is my Arduino Mega sketch source code to allow you to read/write/erase PS3 Syscon EEPROM.
http://pastie.org/10004682#8,19



{{Reverse engineering}}<noinclude>[[Category:Main]]</noinclude>