Editing DualShock 3

Jump to navigation Jump to search
Warning: You are not logged in. Your IP address will be publicly visible if you make any edits. If you log in or create an account, your edits will be attributed to your username, along with other benefits.

The edit can be undone. Please check the comparison below to verify that this is what you want to do, and then publish the changes below to finish undoing the edit.

Latest revision Your text
Line 1: Line 1:
== Overview ==
== Overview ==
<div style="float:right">[[File:Dual-shock-3-x-ray.jpg|400px|thumb|left|DualShock 3 X-rays photo<br>V3.5X board]]<br>[[File:PS3-sixaxis-dualshock-controller-buttons.gif|400px|thumb|left|DualShock 3 Buttons]]</div>
<div style="float:right">[[File:Dual-shock-3-x-ray.jpg|170px|thumb|left|DualShock 3 x-ray]]</div>
[[CECH-ZC2J]], [[CECH-ZC2JA]], [[CECH-ZC2JB]] <small>([[CECH-ZC2U]] <!-- Prototype: CBEH-1040U -->, [[CECH-ZC2E]], [[CECH-ZC2J]], [[CECH-ZC2H]], [[CECH-ZC2M]])</small><br />
[[CECH-ZC2J]], [[CECH-ZC2JA]], [[CECH-ZC2JB]] <small>([[CECH-ZC2U]], [[CECH-ZC2E]], [[CECH-ZC2J]], [[CECH-ZC2H]], [[CECH-ZC2M]])</small><br />
[[CECHZC2]] ([[SCPH-98050]], [[CBEH-1018]]: prototype)<br />
[[CECHZC2]] ([[SCPH-98050]], [[CBEH-1018]]: prototype)<br />
FCC ID: AK8CECHZC2 <br />
FCC ID: AK8CECHZC2 <br />
Line 28: Line 28:
! Model Number !! Name description !! Release date !! Note
! Model Number !! Name description !! Release date !! Note
|-
|-
| [[CECH-ZC2J]]    || [[File:DS3-Black.jpg|24px|Black]] Black || 2007, November 11 || Japan
| [[CECHZC2J]]    || [[File:DS3-Black.jpg|24px|Black]] Black || 2007, November 11 || Japan
|-
|-
| [[CECH-ZC2J]] SS || [[File:DS3-Satin Silver.jpg|24px|Satin Silver]] Satin Silver || 2008, March 6 || Japan
| [[CECHZC2J]] SS || [[File:DS3-Satin Silver.jpg|24px|Satin Silver]] Satin Silver   || 2008, March 6 || Japan
|-
|-
| [[CECH-ZC2J]] MB || [[File:DS3-Metallic Blue.jpg|24px|Metallic Blue]] Metallic Blue || 2009, October 29 || Japan
| [[CECH-ZC2J]] MB || [[File:DS3-Metallic Blue.jpg|24px|Metallic Blue]] Metallic Blue   || 2009, October 29 || Japan
|-
|-
| [[CECH-ZC2J]] DR || [[File:DS3-Deep Red.jpg|24px|Deep Red]] Deep Red || 2009, October 29 || Japan
| [[CECH-ZC2J]] DR || [[File:DS3-Deep Red.jpg|24px|Deep Red]] Deep red        || 2009, October 29 || Japan
|-
|-
| [[CECH-ZC2J]] LW || [[File:DS3-Classic White.jpg|24px|Classic White]] Classic White || 2010, July 29 || Japan
| [[CECH-ZC2J]] LW || [[File:DS3-Classic White.jpg|24px|Classic White]] Classic White   || 2010, July 29 || Japan
|-
|-
| [[CECH-ZC2J]] CW || [[Ceramic White]] || 2009, November 11 || Japan
| [[CECH-ZC2J]] CP || [[File:DS3-Candy Pink.jpg|24px|Candy Pink]] Candy Pink      || 2010, November 18 || Japan
|-
|-
| [[CECH-ZC2J]] CP || [[File:DS3-Candy Pink.jpg|24px|Candy Pink]] Candy Pink || 2010, November 18 || Japan
| [[CECH-ZC2J]] YB || [[File:DS3-Candy Blue.jpg|24px|Candy Blue]] Candy Blue      || 2011, April 21 || Japan
|-
|-
| [[CECH-ZC2J]] YB || [[File:DS3-Candy Blue.jpg|24px|Candy Blue]] Candy Blue || 2011, April 21 || Japan
| [[CECH-ZC2J]] JG || [[File:DS3-Jungle Green.jpg|24px|Jungle Green]] Jungle Green    || 2011, February 24 || Japan
|-
|-
| [[CECH-ZC2J]] JG || [[File:DS3-Jungle Green.jpg|24px|Jungle Green]] Jungle Green || 2011, February 24 || Japan
| [[CEJH-15017]]   || TALES OF XILLIA®2 X cross Edition || 2012, November 1 || Japan
|-
| [[CECH-ZC2J]] CM || [[File:DS3-Urban Camouflage.jpg|24px|Urban Camouflage]] Urban Camouflage || 2011, November 17 || Japan
|-
| [[CECH-ZC2J]] MG || [[File:DS3-Metallic Gold.jpg|24px|Metallic Gold]] Metallic Gold || 2012, June || Europe
|-
| [[CEJH-15017]] || [[File:TalesofXilliaController.jpg|24px|Tales of Xillia]] TALES OF XILLIA®2 X cross Edition || 2012, November 1 || Japan
|-  
|-  
| (N/A, Bundled) || [[Scarlet Red]] || 2011, November 17 || Japan
| [[CEJH-15020]]   || God of War: Ascension bundle || 2013, March 14 || Japan
|-
| (N/A, Bundled) || [[Titanium Blue]] || ||
|-
| (N/A, Bundled) || [[Splash Blue]] || 2011, November 17 || Japan
|-
| (N/A, Bundled) || [[Magical Gold]] || ||
|-
| (N/A, Bundled) || [[File:Yakuza5controller.png|24px|Yakuza Gold]] Yakuza Gold || ||
|-
| (N/A, Bundled) || [[File:FotNS.png|24px|FotNS]] Fist of the North Star|| ||
|-
|  Gunmetal Grey || [[Gunmetal Grey]] || ||
|-
|  Sand, Brown || [[File:Uncharted3controller.jpg|24px|Uncharted 3]] Uncharted 3 || 2011, November 2 || Japan
|-
| [[CEJH-15020]] || [[File:GoWAController.png|24px|God of War Ascension]] God of War: Ascension || 2013, March 14 || Japan
|-
|-
| [[CECH-ZC2J]] MY || [[File:DS3-Metallic Grey.jpg|24px|Metallic Grey]] Metallic Grey || 2013, June 20 || Japan
| [[CECH-ZC2J]] MY || [[File:DS3-Metallic Grey.jpg|24px|Metallic Grey]] Metallic Grey || 2013, June 20 || Japan
Line 74: Line 52:
| [[CECH-ZC2J]] VT || Vita TV edition (White) || 2013, November 14 || Japan
| [[CECH-ZC2J]] VT || Vita TV edition (White) || 2013, November 14 || Japan
|-
|-
| [[CECH-ZC2J]] CY || [[File:DS3-Crystal.jpg|24px|Crystal]] Crystal || 2013, December 19 || Japan
| [[CECH-ZC2J]] CY || [[File:DS3-Crystal.jpg|24px|Crystal]]Crystal || 2013, December 19 || Japan
|-
| [[CECH-ZC2J]] RQX || [[File:DS3-Crimson Red.jpg|24px|Crimson Red]] Crimson Red ||  ||
|-
| [[CECH-ZC2J]] OB || [[File:Cosmic-blue.jpg|24px|Cosmic Blue]] Cosmic Blue || ||
|-
| (N/A, Bundled) || [[File:MGRR-blue.png|24px|MGRR Blue]] MGR Blue || 2013, February 21 || Japan
|-
|-
| [[CECH-ZC2J]] BJ || [[File:DS3-Slate Grey.jpg|24px|Slate Grey]] Slate Grey ||  ||  
| || [[File:DS3-Crimson Red.jpg|24px|Crimson Red]] Crimson Red ||  ||  
|-
|-
| [[CECH-ZC2J]] BB || [[File:DS3-MLBDS3.jpg|24px|MLB]] MLB 11: The Show ||  ||  
| || [[File:DS3-Metallic Gold.jpg|24px|Metallic Gold]] Metallic Gold ||  ||  
|-
|-
| [[CECH-ZC2J]] FTX || [[FF13]] || || Japan
|  || [[File:DS3-Slate Grey.jpg|24px|Slate Grey]] Slate Grey || ||  
|-
|-
| [[CECH-ZC2J]] LRX || [[FF13-2]] || || Japan
|  || [[File:DS3-Urban Camouflage.jpg|24px|Urban Camouflage]] Urban Camouflage || ||  
|-
|-
|}
|}


*Regions (last letter of the "model number"):
*Regions (last letter of the "model number"):
**A Australia (not small letter)
**E Europe
**E Europe
**H Hong Kong
**H Hong Kong
Line 101: Line 72:
**R Russia
**R Russia
**T Taiwan
**T Taiwan
**U United States & Canada
**U United States
**M Mexico (seen in Anatel.br)
**M Mexico (seen in Anatel.br)


*Revisions (small letter + number after the "model number")
*Revisions (small letter + number after the "model number")
**A1 https://www.psdevwiki.com/ps3/File:2Ern4.jpg
**A1 http://i.imgur.com/2Ern4.jpg
**B1
**B1
**A2 https://www.psdevwiki.com/ps3/File:E89hU5o.jpg


== Controller Components ==
== Controller Components ==
Line 132: Line 102:
* Label on the back reads '''0604KATA2'''
* Label on the back reads '''0604KATA2'''
* Toshiba MCU is on top side of the board (in all the other models is at bottom)
* Toshiba MCU is on top side of the board (in all the other models is at bottom)
* The main board was designed without [https://www.allaboutcircuits.com/technical-articles/introduction-to-mems-gyroscopes-vibratory-gyroscope/ gyroscope] and without accelerometer sensors, it has a "children board" sticked on top manufactured by HDK (the first 2 letters of the "HDK" brand are partially visible etched on copper on the children board), this children board includes the accelerometer '''HDK HAAM 325B''' [https://www.hdk.co.jp/japanese/topics_j/tpc053_j.htm]. It outputs 3 signals on the 3 white wires "hand made" soldered to the TOSHIBA controller to retrieve the axis data. The other "hand made" soldered component uses 3 wires (black = ground, red = volts, and yellow soldered to TP26) seems to be a '''Murata ENC-03R''' Gyroscope Sensor [http://www.alldatasheet.es/datasheet-pdf/pdf/191258/MURATA/ENC-03R.html]. It seems both components was integrated later in the circuit board of the controllers labeled "sixaxis"
* The main board was designed without gyroscope and without accelerometer sensors, it has a "children board" sticked on top manufactured by HDK (the first 2 letters of the "HDK" brand are partially visible etched on copper on the children board), this children board includes the accelerometer '''HDK HAAM 325B''' [https://www.hdk.co.jp/japanese/topics_j/tpc053_j.htm]. It outputs 3 signals on the 3 white wires "hand made" soldered to the TOSHIBA controller to retrieve the axis data. The other "hand made" soldered component uses 3 wires (black = ground, red = volts, and yellow soldered to TP26) seems to be a '''Murata ENC-03R''' Gyroscope Sensor [http://www.alldatasheet.es/datasheet-pdf/pdf/191258/MURATA/ENC-03R.html]. It seems both components was integrated later in the circuit board of the controllers labeled "sixaxis"


Internally the Gyroscopic sensor for Sixaxis controllers is wired onto the board - presumably as a test for a sensor revision on a spare sample board. The sensor itself appears to be far from complete and very early.
Internally the Gyroscopic sensor for Sixaxis controllers is wired onto the board - presumably as a test for a sensor revision on a spare sample board. The sensor itself appears to be far from complete and very early.
Line 169: Line 139:
**MSU_V2 2.12
**MSU_V2 2.12
**MSU_V2 2.14
**MSU_V2 2.14
**MSU_V2.5 1.05


Notable differences
Notable differences
Line 178: Line 149:
File:MSU V2 2.14 (Top).jpg|MSU_V2 2.14<br>(Top)
File:MSU V2 2.14 (Top).jpg|MSU_V2 2.14<br>(Top)
File:MSU V2 2.14 (Bottom).jpg|MSU_V2 2.14<br>(Bottom)
File:MSU V2 2.14 (Bottom).jpg|MSU_V2 2.14<br>(Bottom)
</gallery>
===== V2.5 =====
*Models
**MSU_V2.5 1.05
**MSU_V2.5 1.06
<gallery>
File:MSU V2.5 1.05 (Top).jpg|MSU_V2.5 1.05<br>(Top)
File:MSU V2.5 1.05 (Top).jpg|MSU_V2.5 1.05<br>(Top)
File:MSU V2.5 1.05 (Bottom).jpg|MSU_V2.5 1.05<br>(Bottom)
File:MSU V2.5 1.05 (Bottom).jpg|MSU_V2.5 1.05<br>(Bottom)
Line 206: Line 169:
</gallery>
</gallery>


===== V3.5X =====
===== VX3.5X =====
*Models
*Models
**MSU_V3.5X 1.12
**MSU_V3.5X 1.12
Line 270: Line 233:


Notable differences
Notable differences
*Potentiometer sticks with 3 legs, previous versions had 4 legs
*Sticks potenciometers with 3 legs, previous versions had 4 legs


<gallery>
<gallery>
Line 282: Line 245:
**MSU_VX7_0.04
**MSU_VX7_0.04


PCB is multilayer
<gallery>
<gallery>
File:MSU VX7 0.04 (Top).jpg|MSU_VX7_0.04<br>(Top)
File:MSU VX7 0.04 (Top).jpg|MSU_VX7_0.04<br>(Top)
Line 289: Line 251:


===== VX8 =====
===== VX8 =====
The VX8 is official, the board traces, testpoint locations, and the sensor chips has a lot of coincidences with VX7... the weird thing that is shocking is the toshiba chip and the alps bluetooth module has been replaced. The PCB has more than 2 layers (previous versions up to VX6 had only 2 layers)
<strike>There is not much info about this model, so is not clear if is the official VX8 or a third party clone of VX7</strike>The VX8 is official, the board traces, testpoint locations, and the sensor chips has a lot of coincidences with VX7... the weird thing that is shocking is the toshiba chip and the alps bluetooth module has been replaced


<gallery>
<gallery>
File:MSU VX8 0.14 (top).jpg|MSU VX8 0.14 (top)
File:MSU VX8 0.14 (top).jpg|MSU VX8 0.14 (top)
File:MSU VX8 0.14 (bottom).jpg|MSU VX8 0.14 (bottom)
File:MSU VX8 0.14 (bottom).jpg|MSU VX8 0.14 (bottom)
File:MSU VX8 unknown (Bottom).jpg|MSU_VX8_?.?? (Bottom)
File:MSU VX8 unknown (Bottom).jpg|MSU_VX8_?.??<br>(Bottom)
File:MSU VX8 0.14 BOTTOM.jpg
File:MSU VX8 0.14 BOTTOM marked.jpg
File:MSU VX8 0.14 TOP.jpg
</gallery>
</gallery>


Line 305: Line 264:


*Models
*Models
**ASUKA REV: 1.05
**ASUKA REV: 1.06
**ASUKA REV: 1.06
**ASUKA REV: 1.07
**ASUKA REV: 1.07
Line 318: Line 276:


=== Ribbon Circuit Boards ===
=== Ribbon Circuit Boards ===
For any arcade stick builders soldering to the vias on the PCB board (in the models where there are no testpoints availables) isn't exactly the easiest thing to do, using the copper contacts for the ribbon board is really the best option. In some board models (VX3, VX4, VX5, VX6, VX8) the copper contacts are covered by a black carbon material that needs to be removed if these spots are to be used to solder in them, this can be done with an X-acto knife or some fine sandpaper, just be careful and when you get to the shiny copper, STOP, you're done. Tin it up with some solder and there are your spots to use. Try and use a 30awg wire, or 28awg at the largest, and make sure to secure the wiring with some hot glue after you make the connection, but don't glue over the solder joint you just made, secure the wire to the board back from the solder joint, in case you ever have to get to it again for any reason.
The pull-up 7.5k Resistors ("printed" on the ribbon circuit boards) also need to be put back in the circuit as they're built into the ribbon board and when it's removed they're not, and the controller will act up on you if these are not in the circuit. There needs to be 2 of these pull-up resistors installed, one goes from V_STBY to COM1, the other goes from V_STBY to COM2. If you don't have any 7.5k resistors you can use anything from 6.8k to 10k really, but they do need to be installed since the ribbon board is removed when building an arcade stick, all of the PS3 controllers are setup this way and need those pull-up resistors if the ribbon board is removed


{| class="wikitable" border="1"
{| class="wikitable" border="1"
Line 329: Line 284:
|-
|-
| VX || SA1Q146A ||  || The first dualshock 3 model
| VX || SA1Q146A ||  || The first dualshock 3 model
|-
| VX || SA1Q147A ||  || Found in a CECHZC2U (USA)
|-
|-
| ? || SA1Q159A || rowspan="4" {{Yes}} ||  
| ? || SA1Q159A || rowspan="4" {{Yes}} ||  
|-
|-
|VX3 || SA1Q160A ||  
| ? || SA1Q160A ||  
|-
|-
| ? || SA1Q188A ||  
| ? || SA1Q188A ||  
Line 342: Line 295:
| VX5 || SA1Q194A ||  || not compatible with previous models, PS button changes
| VX5 || SA1Q194A ||  || not compatible with previous models, PS button changes
|-
|-
| VX6 || SA1Q195A ||  ||  
| ? || SA1Q195A ||  ||  
|-
|-
| VX7 ? || SA1Q222A || rowspan="2" {{Yes}}  || superslims date ?. Is composed by 2 separated ribbons
| VX7 ? || SA1Q222A || rowspan="2" {{Yes}}  || superslims date ?. Is composed by 2 separated ribbons
Line 355: Line 308:


==== SA1Q146A ====
==== SA1Q146A ====
==== SA1Q147A ====


==== SA1Q159A ====
==== SA1Q159A ====
Line 376: Line 327:


==== SA1Q189A ====
==== SA1Q189A ====
<gallery>
File:SA1Q189A.jpg|Dualshock 3 Ribbon Circuit Board SA1Q189A
</gallery>


==== SA1Q194A ====
==== SA1Q194A ====
Line 386: Line 334:


==== SA1Q195A ====
==== SA1Q195A ====
<gallery>
File:Dualshock 3 Ribbon Circuit Board SA1Q195A.jpg|Dualshock 3 Ribbon Circuit Board SA1Q195A
</gallery>


==== SA1Q222A ====
==== SA1Q222A ====
Line 419: Line 364:
==== MK11-2902 ====
==== MK11-2902 ====
3.7V 610mAh
3.7V 610mAh
==== MK11-3023 ====
==== MK11-3020 ====
3.7V 570mAh (typ. 610mAh)
3.7V 570mAh (typ. 610mAh)


Line 453: Line 398:


=== Memory (EEPROM) ===
=== Memory (EEPROM) ===
All the EEPROMS uses the TSSOP 8-Pin package, the first ones uses [https://learn.sparkfun.com/tutorials/serial-peripheral-interface-spi SPI protocol] and last one [https://learn.sparkfun.com/tutorials/i2c I2C protocol]. Are located the most closer posible to the toshiba controller (the master of the SPI channel), in the opposite side of the board aligned to a border of it
The EEPROM is located the most closer posible to the toshiba controller, usually in the opposite side of the board where the toshiba controller is located, aligned to a border of it
 
If you scroll down this wiki page a bit you will notice the pinout of the first EEPROM is the same than the next ones, the pinout tables are repeated for convenience, in the case of the Renesas 504E it was used in boards PP1, PP4, V2, V2.5, VX, V3.5X but that boards had different versions of the toshiba MCU (T6UM'''2'''EFG-0'''103''', T6UM'''3'''EFG-00'''1''', T6UN'''6'''EFG-00'''1''', T6UN'''6'''EFG-00'''2'''), some pins of that component was remapped at some point, probably this changes never affected the EEPROM pins (so this info about the toshiba pinout could be removed from here because can be seen in the [[Template:Toshiba T6UN6EFG Pinout]]), but by now are kept here inside the EEPROM pinout tables just incase someone needs or wants to add accurate pin-to-pin details of an specific board model. If at some point it can be verifyed that all EEPROM pins are connected to the same toshiba MCU pins in all the board models then it will be better to replace all duplicated EEPROM pinout tables by a single one but until that happens is better this way. Also the tables can be used to add info about the board testpoints, new board models doesnt have testpoints for EEPROM lines but is posible some old models have them, in that case this tables can be used to add info about them (while rushing as i did) and later move that EEPROM testpoint info to [[Template:PlayStation 3 controller PCB TestPoints]]


==== Renesas 504E ====
==== Renesas 504E ====
<div style="float:right">[[File:Renesas 504E.jpg|200px|thumb|right|Renesas 504E]]</div>
<div style="float:right">[[File:Renesas 504E.jpg|200px|thumb|right|Renesas 504E]]</div>
Used in boards: PP1, PP4, V2, V2.5 (all prototypes and retail sixasix models), VX, V3.5X (the first dualshock 3 models)
Renesas HN58X2504TIE
*Renesas HN58X2504I
*https://www.renesas.com/en-eu/products/memory/eeprom/device/HN58X2504TI.html
*https://www.renesas.com/en-eu/doc/products/memory/rej03c0061_hn58x250204i.pdf


4k EEPROM (512-word × 8-bit). It realizes high speed, low power consumption and a high level of reliability by employing advanced MONOS memory technology and CMOS process and low voltage circuitry technology. It also has a 16-byte page programming function to make it’s write operation faster
https://www.renesas.com/en-eu/products/memory/eeprom/device/HN58X2504TI.html https://www.renesas.com/en-eu/doc/products/memory/rej03c0061_hn58x250204i.pdf


{| class="wikitable"
{| class="wikitable"
Line 470: Line 410:
! Pin !! Name !! Notes
! Pin !! Name !! Notes
|-
|-
| 1 || {{cellcolors|#d699ff}} EEPROM_SELECT || To Toshiba '''T6UN*EFG pin ?'''
| 1 || ||  
|-
|-
| 2 || {{cellcolors|#d699ff}} EEPROM_<abbr title="Master-In Slave-Out">SPI_MISO</abbr> || To Toshiba '''T6UN*EFG pin ?'''
| 2 || ||  
|-
|-
| 3 || {{cellcolors|#ff9933}} <abbr title="Write protect">V_STBY</abbr> || To '''Standby power''' rail
| 3 || {{cellcolors|#ff9933}} V_STBY ? ||  
|-
|-
| 4 || {{cellcolors|#000000|#ffffff}} GND || To '''ground'''
| 4 || ||  
|-
|-
| 5 || {{cellcolors|#d699ff}} EEPROM_<abbr title="Master-Out Slave-In">SPI_MOSI</abbr> || To Toshiba '''T6UN*EFG pin ?'''
| 5 || ||  
|-
|-
| 6 || {{cellcolors|#d699ff}} EEPROM_<abbr title="Master clock">SPI_CLOCK</abbr> || To Toshiba '''T6UN*EFG pin ?'''
| 6 || ||  
|-
|-
| 7 || {{cellcolors|#ff9933}} <abbr title="Hold">V_STBY</abbr> || rowspan="2" | To '''Standby power''' rail
| 7 || {{cellcolors|#ff9933}} V_STBY ? ||  
|-
|-
| 8 || {{cellcolors|#ff9933}} V_STBY
| 8 || {{cellcolors|#ff9933}} V_STBY ? ||
|}
|}


==== Seiko Instruments S25C ====
==== Seiko Instruments S25C 040A ====
<div style="float:right">[[File:Seiko Instruments S25C 040A.jpg|200px|thumb|right|Seiko Instruments S25C 040A]]</div>
<div style="float:right">[[File:Seiko Instruments S25C 040A.jpg|200px|thumb|right|Seiko Instruments S25C 040A]]</div>
Used in boards: VX3, VX4, VX5, VX6
http://www.sii-ic.com/en/semicon/datasheets/memory/general-serial-eeprom/s-25c010a-020a-040a/ http://datasheet.sii-ic.com/en/serial_eeprom/S25C010A_020A_040A_E.pdf
*Seiko Instruments S-25C040A
[[File:Seiko Instruments S-25C040A0I-T8T1G pinout.jpg|600px|thumb|left|Seiko Instruments S-25C040A0I-T8T1G pinout]]
*http://www.sii-ic.com/en/semicon/datasheets/memory/general-serial-eeprom/s-25c010a-020a-040a/
Seiko Instruments S-25C040A0I-T8T1G
*http://datasheet.sii-ic.com/en/serial_eeprom/S25C010A_020A_040A_E.pdf


The S-25C040A is a SPI serial EEPROM which operate at high speed, with low current consumption and the wide range operation. Has 4 K-bit capacity and the organization of 512 words × 8-bit. Page write and sequential read are available
EEPROM - 4Kb, CMOS, SPI
 
<div style="clear:both;"></div>
{| class="wikitable"
|-
! Pin !! Name !! Notes
|-
| 1 || {{cellcolors|#d699ff}} EEPROM_SELECT || To Toshiba '''T6UN6EFG''' (pin '''31''' in VX5)
|-
| 2 || {{cellcolors|#d699ff}} EEPROM_<abbr title="Master-In Slave-Out">SPI_MISO</abbr> || To Toshiba '''T6UN6EFG''' (pin '''35''' in VX5)
|-
| 3 || {{cellcolors|#ff9933}} <abbr title="Write protect">V_STBY</abbr> || To '''Standby power''' rail
|-
| 4 || {{cellcolors|#000000|#ffffff}} GND || To '''ground'''
|-
| 5 || {{cellcolors|#d699ff}} EEPROM_<abbr title="Master-Out Slave-In">SPI_MOSI</abbr> || To Toshiba '''T6UN6EFG''' (pin '''34''' in VX5)
|-
| 6 || {{cellcolors|#d699ff}} EEPROM_<abbr title="Master clock">SPI_CLOCK</abbr> || To Toshiba '''T6UN6EFG''' (pin '''30''' in VX5)
|-
| 7 || {{cellcolors|#ff9933}} <abbr title="Hold">V_STBY</abbr> || rowspan="2" | To '''Standby power''' rail
|-
| 8 || {{cellcolors|#ff9933}} V_STBY
|}


==== STMicroelectronics 504RP ====
==== STMicroelectronics 504RP ====
<div style="float:right">[[File:STMicroelectronics 504RP.jpg|200px|thumb|right|STMicroelectronics 504RP]]</div>
<div style="float:right">[[File:STMicroelectronics 504RP.jpg|200px|thumb|right|STMicroelectronics 504RP]]</div>
Used in boards: VX4, VX5, VX6, VX7
http://www.st.com/content/st_com/en/products/memories/serial-eeprom/standard-serial-eeprom/standard-spi-eeprom/m95040-r.html ?
*STMicroelectronics M95040-RP
*http://www.st.com/content/st_com/en/products/memories/serial-eeprom/standard-serial-eeprom/standard-spi-eeprom/m95040-r.html
*http://www.st.com/resource/en/datasheet/m95040-r.pdf
* bin file VX5.bin
4 Kbit (512x8 bits) serial SPI bus EEPROM with high-speed clock


{| class="wikitable"
{| class="wikitable"
Line 530: Line 444:
! Pin !! Name !! Notes
! Pin !! Name !! Notes
|-
|-
| 1 || {{cellcolors|#d699ff}} EEPROM_SELECT || To Toshiba '''T6UN6EFG''' (pin '''31''' in VX4)
| 1 || {{cellcolors|#3CB371}} EEPROM_SELECT || To Toshiba '''T6UN6EFG, pin 31'''
|-
|-
| 2 || {{cellcolors|#d699ff}} EEPROM_<abbr title="Master-In Slave-Out">SPI_MISO</abbr> || To Toshiba '''T6UN6EFG''' (pin '''35''' in VX4)
| 2 || {{cellcolors|#3CB371}} EEPROM_DATA_OUT || To Toshiba '''T6UN6EFG, pin 35'''
|-
|-
| 3 || {{cellcolors|#ff9933}} <abbr title="Write protect">V_STBY</abbr> || To '''Standby power''' rail
| 3 || {{cellcolors|#ff9933}} V_STBY || '''2.8V Standby'''. Power for {{padps}}, LED's, EEPROM, etc...
|-
|-
| 4 || {{cellcolors|#000000|#ffffff}} GND || To '''ground'''
| 4 || {{cellcolors|#000000|#ffffff}} GND || To '''ground'''
|-
|-
| 5 || {{cellcolors|#d699ff}} EEPROM_<abbr title="Master-Out Slave-In">SPI_MOSI</abbr> || To Toshiba '''T6UN6EFG''' (pin '''34''' in VX4)
| 5 || {{cellcolors|#3CB371}} EEPROM_DATA_IN || To Toshiba '''T6UN6EFG, pin 34'''
|-
|-
| 6 || {{cellcolors|#d699ff}} EEPROM_<abbr title="Master clock">SPI_CLOCK</abbr> || To Toshiba '''T6UN6EFG''' (pin '''30''' in VX4)
| 6 || {{cellcolors|#3CB371}} EEPROM_CLOCK || To Toshiba '''T6UN6EFG, pin 30'''
|-
|-
| 7 || {{cellcolors|#ff9933}} <abbr title="Hold">V_STBY</abbr> || rowspan="2" | To '''Standby power''' rail
| 7 || {{cellcolors|#ff9933}} V_STBY || rowspan="2" | '''2.8V Standby'''. Power for {{padps}}, LED's, EEPROM, etc...
|-
|-
| 8 || {{cellcolors|#ff9933}} V_STBY
| 8 || {{cellcolors|#ff9933}} V_STBY
Line 549: Line 463:
==== STMicroelectronics 432RK ====
==== STMicroelectronics 432RK ====
<div style="float:right">[[File:STMicroelectronics 432RK.jpg|200px|thumb|right|STMicroelectronics 432RK]]</div>
<div style="float:right">[[File:STMicroelectronics 432RK.jpg|200px|thumb|right|STMicroelectronics 432RK]]</div>
Used in board: VX8 only
*STMicroelectronics M24C32-RK
*http://www.st.com/content/st_com/en/products/memories/serial-eeprom/standard-serial-eeprom/standard-i2c-eeprom/m24c32-r.html
*http://www.st.com/resource/en/datasheet/m24c32-r.pdf
The M24C32 is a 32-Kbit I2C-compatible EEPROM (Electrically Erasable PROgrammable Memory) organized as 4 K × 8 bits


{| class="wikitable"
{| class="wikitable"
Line 560: Line 468:
! Pin !! Name !! Notes
! Pin !! Name !! Notes
|-
|-
| 1 || {{cellcolors|#000000|#ffffff}} <abbr title="E0 Chip enable">GND</abbr> || rowspan="4" | To '''ground'''
| 1 || {{cellcolors|#000000|#ffffff}} GND ? ||  
|-
|-
| 2 || {{cellcolors|#000000|#ffffff}} <abbr title="E1 Chip enable">GND</abbr>
| 2 || {{cellcolors|#000000|#ffffff}} GND ? ||
|-
|-
| 3 || {{cellcolors|#000000|#ffffff}} <abbr title="E2 Chip enable">GND</abbr>
| 3 || {{cellcolors|#000000|#ffffff}} GND ? ||
|-
|-
| 4 || {{cellcolors|#000000|#ffffff}} GND
| 4 || {{cellcolors|#000000|#ffffff}} GND ? ||
|-
|-
| 5 || {{cellcolors|#d699ff}} EEPROM_<abbr title="Serial data">I2C_SDA</abbr> || To <abbr title="the toshiba main MCU was replaced in VX8">Unknown MCU</abbr>, pin ?
| 5 || {{cellcolors|#3CB371}} EEPROM ? || To Toshiba '''T6UN6EFG, pin ?'''
|-
|-
| 6 || {{cellcolors|#d699ff}} EEPROM_<abbr title="Serial clock">I2C_SCL</abbr> || To <abbr title="the toshiba main MCU was replaced in VX8">Unknown MCU</abbr>, pin ?
| 6 || {{cellcolors|#3CB371}} EEPROM ? || To Toshiba '''T6UN6EFG, pin ?'''
|-
|-
| 7 || {{cellcolors|#d699ff}} EEPROM_<abbr title="Write control">I2C_WC</abbr> || To <abbr title="the toshiba main MCU was replaced in VX8">Unknown MCU</abbr>, pin ?
| 7 || {{cellcolors|#3CB371}} EEPROM ? || To Toshiba '''T6UN6EFG, pin ?'''
|-
|-
| 8 || {{cellcolors|#ff9933}} V_STBY || To '''Standby power''' rail ?
| 8 || {{cellcolors|#ff9933}} V_STBY ?
|}
|}


----
----
 
=== Power ===
=== Power control ===


==== Texas Instruments BKO ====
==== Texas Instruments BKO ====
<div style="float:right">[[File:Texas Instruments BKO.jpg|200px|thumb|right|Texas Instruments BKO]]</div>
<div style="float:right">[[File:Texas Instruments BKO.jpg|200px|thumb|right|Texas Instruments BKO]]</div>
10 pins. Used in PP1, PP4, V2, V2.5 boards (all prototypes and retail sixasix models)
Texas Instruments BQ24027DRCR
*Texas Instruments BQ24027
*bqTINY-II dual input USB/AC 1-Cell Li-Ion charger with "charge enable" input & "power good" output
*bqTINY-II dual input USB/AC 1-Cell Li-Ion charger with "charge enable" input & "power good" output
*http://www.ti.com/product/BQ24027 http://www.ti.com/lit/ds/symlink/bq24027.pdf
*http://www.ti.com/product/BQ24027 http://www.ti.com/lit/ds/symlink/bq24027.pdf


This component is designed to work as a battery charger able to select automatically the power source from 2 optional inputs (based in the presence of them), from either an external AC adapter or from a USB cable. In the datasheet this 2 power sources are connected to pin 1 (AC) and pin 2 (USB). But the playstation 3 controllers doesnt have a connector for an AC adapter aaauch... This is the reason why the V_USB rail of the circuit board is connected to pin 1, and pin 2 seems to be unconnected. In other words... the USB is connected to the pin where it was supposed to be connected an AC adapter (pin 1) and there is nothing in pin 2
This component is designed to work as a battery charger that is able to select automatically the power source from 2 optional inputs (based in the presence of them, one, both, or none), from either an external AC adapter or from a USB cable. In the datasheet this 2 power sources are connected to pin 1 (AC) and pin 2 (USB). But the playstation 3 controllers doesnt have a connector for an AC adapter aaauch... This is the reason why the V_USB line is connected to pin 1, and pin 2 seems to be unconnected. Is not doing any power input selection because the only power input available to charge the battery is USB. The reason why sony chose this one (even not fitting very well with the requirements of the playtation 3 controller) is because seems to be very accurate in voltage regulations and it has some additional features to control and monitor the charging processes
 
There are three consequences of this "hack", every power input pin has specific features for it (internally the component has different subcircuits for each power input). Basically the most important ones are the charge current from pin 2 (intended for USB power input) can be controlled by pin 7, it has 3 charge modes for the battery (high=500 mA, low=100mA, hi-z=disable USB charge), but because there is nothing connected to pin 2 all this internal circuits are pointless... This is the reason why in the photos looks like pin 7 is connected to ground, by grounding it sets the charge mode in 100mA but the only purpose of grounding it is to set that pin in a stable state, so is grounded for safety
 
The second consequence of this hack is the power input connected to pin 1 allows for a much more better control of the charge voltages (it was intended for an AC adapter but here is used for USB), the datasheet tells this is made by using an external resistor connected to pin 6, the value of the resistor indicates the charge mode, intensity, and other settings for a special function able to "wake up" faulty batteries and for the "<abbr title="A charge regime delivering moderately high-rate charging current when the battery is at a low state of charge and tapering the current to lower rates as the battery becomes more fully charged">taper charge</abbr>". Instead of a simple resistor to control all this, what the playstation controller has is several resistors connected in a <abbr title="all board models controls the battery this way, and the components involved seems to be the same in the same configuration... the resistor values and the control signal could vary by board though">very characteristic way</abbr> to a transistor, and this transistor is driven by the main MCU
 
Another pin that changes his function is pin 8, is intended to indicate the presence of an AC adapter connected to pin1, but here we have USB connected to pin 1, so pin 8 indicates the presence of USB power
 
The reason why sony chose this component (even being over the requirements of the playtation 3 controller) is because seems to be very accurate in voltage regulations and it has some additional features to control and monitor the charging processes
 
*'''Battery pre-conditioning'''
**If the battery voltage falls below a threshold during a charge cycle, the bqTINY-II applies a precharge current to the battery. This feature revives deeply discharged cells. The resistor connected between the '''ISET1''' and VSS determines the precharge rate. The bqTINY-II activates a safety timer during the conditioning phase. If threshold is not reached within the timer period, the bqTINY-II turns off the charger and asserts a FAULT code on the STATx pins
 
*'''Battery charge current'''
**The bqTINY-II offers on-chip current regulation with a programmable set point. The resistor connected between the '''ISET1''' and VSS determines the AC charge rate
 
*'''Battery voltage regulation'''
**The voltage regulation feedback is through the OUT pin. This input is tied directly to the positive side of the battery pack. The bqTINY-II monitors the battery-pack voltage between the OUT and VSS pins. When the battery voltage rises to a threshold, the voltage-regulation phase begins and the charging current begins to taper down. As a safety backup, the bqTINY-II also monitors the charge time. If the charge is not terminated within a time period the bqTINY-II turns off the charger and asserts a FAULT code on the STATx pins
 
*'''Charge taper detection, termination, and recharge'''
**The bqTINY-II monitors the charging current during the voltage-regulation phase. Once the taper threshold is detected, the bq24027 terminates the charge. There is no taper timer for this version. The resistor connected between the '''ISET1''' and VSS determines the taper-detect level for AC input. In addition to taper-current detection, the bqTINY-II terminates charge if the charge current falls below the a threshold. This feature allows quick recognition of a battery-removal condition, or insertion of a fully charged battery. Note that the charge timer is bypassed for this feature. The resistor connected between the '''ISET1''' and VSS determines the taper detection level
 
*'''Sleep mode'''
**The bqTINY-II enters low-power sleep mode if both AC and USB are removed from the circuit. This feature prevents draining the battery in the absence of input supply


{| class="wikitable"
{| class="wikitable"
Line 617: Line 500:
! Pin !! Name !! Notes
! Pin !! Name !! Notes
|-
|-
| 1 || {{cellcolors|#ff3333}} V_USB ? || <abbr title="AC adapter in the datasheet, but in the playstation controller this is USB power input so if you read the datahseet keep in mind all the references to USB and AC power sources are swapped">Power source 1</abbr> (and '''TP4''' in PP1 prototype)
| 1 || {{cellcolors|#ff3333}} V_USB ? || <abbr title="AC adaptor in the datasheet">Power source 1</abbr> (and '''TP4''' in PP1 prototype)
|-
|-
| 2 || {{cellcolors|lightgrey}} N/C ?  || <abbr title="USB connector in the datasheet, but in the playstation controller this is unconnected so if you read the datahseet keep in mind all the references to USB specific features are not used here">Power source 2</abbr>
| 2 || {{cellcolors|lightgrey}} N/C ?  || <abbr title="USB connector in the datasheet">Power source 2</abbr>
|-
|-
| 3 || {{cellcolors|#009900}} <abbr title="STAT1">BATT_STATUS_1</abbr> || Battery charge status output 1 (open-drain). To Toshiba main controller ? (and '''TP8''' in PP1 prototype)
| 3 || STAT1 || Charge status output 1 (open-drain). To Toshiba main controller ? (and '''TP8''' in PP1 prototype)
|-
|-
| 4 || {{cellcolors|#009900}} <abbr title="STAT2">BATT_STATUS_2</abbr> || Battery charge status output 2 (open-drain). To Toshiba main controller ? (and '''TP10''' in PP1 prototype)
| 4 || STAT2 || Charge status output 2 (open-drain). To Toshiba main controller ? (and '''TP10''' in PP1 prototype)
|-
|-
| 5 || {{cellcolors|#000000|#ffffff}} GND ? || To '''ground'''
| 5 || {{cellcolors|#000000|#ffffff}} GND ? || To '''ground'''
|-
|-
| 6 || {{cellcolors|#007700}} <abbr title="ISET1">BATT_CHARGE_SETPOINT</abbr> || <abbr title="voltage current setpoint for: precharge, charge, and taper functions">resistors and transistor</abbr> to toshiba main controller ?. (and '''TP64''' in PP1 prototype)
| 6 || ISET1 || <abbr title="this is copyed from the datasheet, note the references to USB and AC sources could be swapped">Charge current set point for AC input and precharge and taper set point for both AC and USB</abbr> (and '''TP64''' in PP1 prototype)
|-
|-
| 7 || {{cellcolors|#000000|#ffffff}} <abbr title="ISET2... seems to be grounded for 100mA... Charge current set point for USB port (high=500 mA, low=100mA, hi-z=disable USB charge)">GND</abbr> ? || To '''ground'''
| 7 || <abbr title="grounded ?... sets the USB charge mode to 100mA">ISET2</abbr> || <abbr title="this is copyed from the datasheet, note the references to USB and AC sources could be swapped">Charge current set point for USB port (high=500 mA, low=100mA, hi-z=disable USB charge)</abbr>
|-
|-
| 8 || {{cellcolors|#008800}} <abbr title="PG">BATT_USB_POWER_GOOD</abbr> || USB power presence detector output (active low). To Toshiba main controller ? (and '''TP6''' in PP1 prototype)
| 8 || PG || <abbr title="indicates the presence of input power">Powergood status output (active low)</abbr>. To Toshiba main controller ? (and '''TP6''' in PP1 prototype)
|-
|-
| 9 || {{cellcolors|#008800}} <abbr title="CE">BATT_CHARGE_START</abbr> || <abbr title="TTL-level charge-enable input used to disable or enable the charge process">Battery charge enable input (active low)</abbr>. To Toshiba main controller ? (<abbr title="This is fully speculative though, it cant be verifyed by looking at the photos availables, but is higly probable based in the numbers of the other testpoints used to check battery">and '''TP7''' in PP1 prototype ?</abbr>)
| 9 || CE || <abbr title="TTL-level charge-enable input used to disable or enable the charge process">Charge enable input (active low)</abbr>. To Toshiba main controller ? (<abbr title="This is fully speculative though, it cant be verifyed by looking at the photos availables, but is higly probable based in the numbers of the other testpoints used to check battery">and '''TP7''' in PP1 prototype ?</abbr>)
|-
|-
| 10 || {{cellcolors|#ff3333}} V_BATT ? || Connected to battery + (and '''TP5''' in PP1 prototype)
| 10 || {{cellcolors|#ff3333}} V_BATT ? || Connected to battery + (and '''TP5''' in PP1 prototype)
|}
|}


*'''PG''': The open-drain PG (Power Good, pin 8) indicates when the "power source 1" (pin 1) is present. The output turns ON when a valid voltage is detected. This output is turned off in the sleep mode. The PG pin can be used to drive a LED or to communicate to the host processor
*PG
**The open-drain PG (power Good) indicates when the AC adapter is present. The output turns ON when a valid voltage is detected. This output is turned off in the sleep mode. The PG pin can be used to drive an LED or to communicate to the host processor.


*'''CE''': The CE digital input (Charge Enable, pin 9) is used to disable or enable the charge process. A low-level signal on this pin enables the charge. A high-level signal disables the charge, and places the device in a low-power mode. A high-to-low transition on this pin also resets all timers and timer fault conditions
*CE
**The CE digital input is used to disable or enable the charge process. A low-level signal on this pin enables the charge. A high-level signal disables the charge, and places the device in a low-power mode. A high-to-low transition on this pin also resets all timers and timer fault conditions. Note that this applies to both AC and USB charging.


*'''ISET1''': The bqTINY-II offers on-chip current regulation with a programmable set point. The resistor connected between the ISET1 and VSS, determines the "power source 1" charge rate
*ISET1
**The bqTINY-II offers on-chip current regulation with a programmable set point. The resistor connected between the ISET1 and Vss , Rset , determines the AC charge rate. The V(set) and K(set) parameters are specified in the specifications table


*'''STAT1''' and '''STAT2''': The open-drain STAT1 and STAT2 outputs indicate various charger operations as shown in the following table. These status pins can be used to drive LEDs or communicate to the host processor. Note that OFF indicates the open-drain transistor is turned off
*ISET2
**When charging from a USB port, the host controller has the option of selecting either a 100-mA or a 500-mA charge rate using the ISET2 pin. A low-level signal sets the current at 100 mA, and a high-level signal sets the current at 500 mA. A high-Z input disables USB charging
 
*STAT1 and STAT2
**The open-drain STAT1 and STAT2 outputs indicate various charger operations as shown in the following table. These status pins can be used to drive LEDs or communicate to the host processor. Note that OFF indicates the open-drain transistor is turned off


{| class="wikitable"
{| class="wikitable"
Line 655: Line 545:
|-
|-
| Charge done || OFF || ON
| Charge done || OFF || ON
|-
| Charge suspend (temperature) || OFF || OFF
|-
| Timer fault || OFF || OFF
|-
|-
| Sleep mode || OFF || OFF
| Sleep mode || OFF || OFF
Line 661: Line 555:
==== NEC 871Y03 ====
==== NEC 871Y03 ====
<div style="float:right">[[File:NEC 871Y03.jpg|200px|thumb|right|NEC 871Y03]]</div>
<div style="float:right">[[File:NEC 871Y03.jpg|200px|thumb|right|NEC 871Y03]]</div>
20 pins. Used in boards: V2, V2.5, (last sixaxis models) and VX (first dualshock 3 model)


{| class="wikitable"
Works as a replacement of the Texas Instruments BKO ?
|-
<div style="clear:both;"></div>
! Pin !! Name !! Notes
|-
| 1 ||  || (Resistor R2 in VX board)
|-
| 2 ||  || (Resistor R2, Fuse SW3, (not mounted) capaitor C59 to ground, and TP13 in VX board)
|-
| 3 || {{cellcolors|#ff9933}} V_STBY || (to ribbon circuit board pins 8 and 14)
|-
| 4 || {{cellcolors|#ff9933}} V_SENSORS ? ||  ('''TP12''' in V2.5 board)
|-
| 5 ||  || (Resistor R53 to ground,Diode D2(pin 1)in VX board)
|-
| 6 ||  || (('''TP60''')(VX board))
|-
| 7 || {{cellcolors|#000000|#ffffff}} GND || To '''ground'''
|-
| colspan="3" {{cellcolors|lightgrey}}
|-
| 8 ||  || (Pin 42 BATT_USB_POWER_GOOD in VX board)
|-
| 9 ||  || capacitor network to ground (CN11 in V2.5 boards), and unknown...
|-
| 10 ||  || capacitor network to ground (CN11 in V2.5 boards), and unknown...
|-
| colspan="3" {{cellcolors|lightgrey}}
|-
| 11 ||  || (RN9 in VX board) to unknown...
|-
| colspan="3" {{cellcolors|lightgrey}}
|-
| 12 ||  ||
|-
| 13 ||  || capacitor (CN10 to ground in VX board), and unknown...
|-
| 14 ||  || capacitor (CN10 to ground in VX board), and unknown...
|-
| 15 ||  || capcitor (C11 to ground in VX board)
|-
| 16 ||  ||
|-
| 17 ||  || Resistor (R3 in VX board)
|-
| colspan="3" {{cellcolors|lightgrey}}
|-
| 18 ||  || resistor (R3 in V2.5 boards), and unknown...,
|-
| colspan="3" {{cellcolors|lightgrey}}
|-
| 19 || {{cellcolors|#ff3333}} V_BATT ? || rowspan="2" | Connected together to a power rail ('''TP5''' in V2.5 board)
|-
| 20 || {{cellcolors|#ff3333}} V_BATT ?
|}


==== Texas Instruments B029 and B029A ====
==== Texas Instruments B029 and B029A ====
<div style="float:right">[[File:Texas Instruments B029.jpg|200px|thumb|left|Texas Instruments B029]][[File:Texas Instruments B029A.jpg|200px|thumb|right|Texas Instruments B029A]]</div>
<div style="float:right">[[File:Texas Instruments B029.jpg|200px|thumb|left|Texas Instruments B029]][[File:Texas Instruments B029A.jpg|200px|thumb|right|Texas Instruments B029A]]</div>
20 pins. Used in boards: V3.5X and VX3
20 pins


{| class="wikitable"
Pin 3 is connected to "reset switch" (SW1), when reset switch is pressed this pin is connected to ground
|+This pinout belongs to B029A
<div style="clear:both;"></div>
! Pin !! Name !! Notes
|-
| 1 ||  ||
|-
| 2 ||  ||
|-
| 3 || {{cellcolors|#666666|#ffffff}} RESET_SWITCH || To '''SW1''', when reset switch is pressed this pin is grounded
|-
| 4 ||  ||
|-
| 5 ||  ||
|-
| 6 || {{cellcolors|#ff3333}} V_USB || (and '''TP1''' in VX4 boards)
|-
| 7 || {{cellcolors|#ff9933}} V_MOTORS ? ||
|-
| 8 || {{cellcolors|#009900}} BATT_STATUS_1 ? || To Toshiba '''T6UN6EFG pin ?''' (and '''TP8''' in V2.5 board ?)
|-
| 9 || {{cellcolors|#009900}} BATT_STATUS_2 ? || To Toshiba '''T6UN6EFG pin ?''' (and '''TP9''' in V2.5 board ?)
|-
| 10 || {{cellcolors|#000000|#ffffff}} GND || To '''ground'''
|-
| colspan="3" {{cellcolors|lightgrey}}
|-
| 11 ||  || Same function as Texas Instruments SN89062 pin 13 ?
|-
| 12 ||  || Same function as Texas Instruments SN89062 pin 14 ?
|-
| 13 ||  || Same function as Texas Instruments SN89062 pin 15 ?
|-
| 14 ||  || Same function as Texas Instruments SN89062 pin 16 ?
|-
| 15 ||  ||
|-
| 16 ||  || Same function as Texas Instruments SN89062 pin 20 ?
|-
| 17 ||  || Same function as Texas Instruments SN89062 pin 21 ?
|-
| 18 ||  || Same function as Texas Instruments SN89062 pin 22 ?
|-
| 19 ||  || Same function as Texas Instruments SN89062 pin 23 ?
|-
| 20 ||  || Same function as Texas Instruments SN89062 pin 24 ?
|}


==== Texas Instruments R2A20060 and SN89062 ====
==== Texas Instruments R2A20060 and SN89062 ====
<div style="float:right">[[File:Texas Instruments R2A20060.jpg|200px|thumb|left|Texas Instruments R2A20060]][[File:Texas Instruments SN89062.jpg|200px|thumb|right|Texas Instruments SN89062]]</div>
<div style="float:right">[[File:Texas Instruments R2A20060.jpg|200px|thumb|left|Texas Instruments R2A20060]][[File:Texas Instruments SN89062.jpg|200px|thumb|right|Texas Instruments SN89062]]</div>
24 pins. Used in boards: VX4, VX6, VX7 (R2A20060 is used in VX4 0.09 boards only and seems to be an early version/prototype of SN89062, both has the same pinout)
24 pins. Used in boards: VX3, VX4, VX6, VX7 (R2A20060 is used in VX4 0.09 boards only and seems to be an early version/prototype of SN89062, both has the same pinout)


{| class="wikitable"
{| class="wikitable"
Line 779: Line 576:
| 1 || {{cellcolors|#000000|#ffffff}} GND || To '''ground'''
| 1 || {{cellcolors|#000000|#ffffff}} GND || To '''ground'''
|-
|-
| 2 || {{cellcolors|#008800}} BATT_CHARGE_START ? || To Toshiba '''T6UN6EFG pin 43'''
| 2 || battery charge enable ? || To Toshiba '''T6UN6EFG, pin 43'''
|-
|-
| 3 || {{cellcolors|#666666|#ffffff}} RESET_SWITCH || To <abbr title="when reset switch is pressed this pin is grounded">'''SW1'''</abbr>
| 3 || {{cellcolors|#666666|#ffffff}} RESET_SWITCH || To '''SW1''', when reset switch is pressed this pin is grounded
|-
|-
| 4 || {{cellcolors|#4477ff}} BT_POWER_ON ? || To Toshiba '''T6UN6EFG pin 13''' with a <abbr title="47K resistor to standby power rail">pull-up resistor</abbr>
| 4 || BT related ? || To Toshiba '''T6UN6EFG, pin 13'''. And 47K resistor to pin 22
|-
|-
| 5 || {{cellcolors|#008800}} BATT_USB_POWER_GOOD ? || To Toshiba '''T6UN6EFG pin 42'''
| 5 || battery powergood ? || To Toshiba '''T6UN6EFG, pin 42'''
|-
|-
| 6 || {{cellcolors|#ff3333}} V_USB || '''USB power rail''' input ('''TP1''' in VX4 boards) with a capacitor to ground. To '''USB connector''' and to '''USB protection diode pin 4''' (see notes below)
| 6 || {{cellcolors|#ff3333}} V_USB || '''USB +5V'''. (and connected to '''TP1''' in VX4 boards)
|-
|-
| 7 || {{cellcolors|#ff9933}} V_BT ? || '''BT power rail''' output ('''TP10''' in VX4 boards) with a capacitor to ground. To '''BT module''' (ALPS '''413A pin 3''' and <abbr title="through resistor and with pull-down resistor... see ALPS 413A pinout for more details">'''pin 2'''</abbr> in VX4 boards)
| 7 || {{cellcolors|#ff9933}} V_BT ? || To '''BT module'''. (ALPS 413A pin 3, and '''TP10''' in VX4 boards). This pin doesnt seems to have voltage either with the controller in standby or working though
|-
|-
| 8 || {{cellcolors|#ff9933}} V_MOTORS || '''Motors power rail''' output ('''TP42''' in VX4 boards). To 2x '''"KEX"''' (<abbr title="or voltage regulators ?">transistors</abbr> ?, 5 pins), and '''BM+1''' (Big Motor +), and '''SM+1''' (Small Motor +)
| 8 || {{cellcolors|#ff9933}} V_MOTORS || Connected to 2x '''"KEX"''' small components (voltage regulators ?, 5 pins), "BM+1" ('''Big Motor +''') and "SM+1" ('''Small Motor +'''). (and '''TP42''' in VX4 boards)
|-
|-
| 9 || {{cellcolors|lightgrey}} N/C ? || <abbr title="dissapears under the component and doesnt seems to continue">Not connected ?</abbr>
| colspan="3" {{cellcolors|lightgrey}}
|-
|-
| 10 || {{cellcolors|#009900}} BATT_STATUS_1 ? || To Toshiba '''T6UN6EFG pin 44''' ('''TP8''' in VX4 boards)
| 9 || {{cellcolors|lightgrey}} N/C ? || Not connected ? (dissapears under the component and doesnt seems to continue)
|-
|-
| 11 || {{cellcolors|lightgrey}} N/C ? || <abbr title="dissapears under the component and doesnt seems to continue">Not connected ?</abbr>
| 10 || BATT_CHARGE_STATUS_1 ? || To Toshiba '''T6UN6EFG, pin 44''' (and '''TP8''' in VX4 boards)
|-
|-
| 12 || {{cellcolors|#009900}} BATT_STATUS_2 ? || To Toshiba '''T6UN6EFG pin 45''' ('''TP9''' in VX4 boards)
| 11 || {{cellcolors|lightgrey}} N/C ? || Not connected ? (dissapears under the component and doesnt seems to continue)
|-
| 12 || BATT_CHARGE_STATUS_2 ? || To Toshiba '''T6UN6EFG, pin 45''' (and '''TP9''' in VX4 boards)
|-
|-
| colspan="3" {{cellcolors|lightgrey}}
| colspan="3" {{cellcolors|lightgrey}}
|-
|-
| 13 || {{cellcolors|#000099|#FF4500}} POWER_BT_UNK ? || To '''BT module''' (ALPS '''413A pin 37''' in VX4 boards) with a <abbr title="47K resistor to ground">pull-down resistor</abbr>
| 13 || || To '''BT module pin 37'''. And to 47K resistor to ground
|-
|-
| 14 || {{cellcolors|#000099|#FF4500}} POWER_BT_UNK ? || To '''BT module''' (ALPS '''413A pin 16''' in VX4 boards) with a <abbr title="47K resistor to standby power rail">pull-up resistor</abbr>
| 14 || || To '''BT module pin 16'''. And to 47K resistor to pin 22
|-
|-
| 15 || {{cellcolors|#000099|#FF4500}} POWER_BT_UNK ? || To '''BT module''' (ALPS '''413A pin 38''' in VX4 boards) with a capacitor to ground
| 15 || || To '''BT module pin 38'''. And capacitor to ground
|-
|-
| 16 || {{cellcolors|#ff3333}} V_BATT || '''Battery power rail''' <abbr title="input when the battery is the only power source in the board, and output to charge the battery when USB power is present">input/output !</abbr> ('''TP14''' in VX4 boards) with a capacitor to ground. To '''battery +''' and toshiba '''T6UN6EFG pin 4''' (see notes below)
| 16 || {{cellcolors|#ff3333}} V_BATT || 4.12V from '''Battery +''' pin, and capacitor to ground, and 147K resistor to Toshiba T6UN6EFG pin 4 (and connected to '''TP14''' in VX4 boards)
|-
|-
| 17 || {{cellcolors|#aa7744}} STICKS_POWER_ON ? || To Toshiba '''T6UN6EFG pin 36'''
| 17 || sticks related ? || To Toshiba '''T6UN6EFG, pin 36'''
|-
|-
| 18 || {{cellcolors|#000000|#ff9933}} V_CAP_1 || <abbr title="0.970uf meassured onboard so maybe not accurate">'''Capacitor'''</abbr> to ground
| 18 || V_CAP_1 || 0.970uf '''Capacitor''' to ground (meassured onboard so maybe not accurate)
|-
|-
| 19 || {{cellcolors|#000099|#FF4500}} POWER_BT_UNK ? || To '''BT module''' (ALPS '''413A pin 15''' in VX4 boards) with a <abbr title="47K resistor to ground">pull-down resistor</abbr>
| 19 || || To '''BT module pin 15'''. And to 47K resistor to ground
|-
|-
| 20 || {{cellcolors|#000000|#ff9933}} V_CAP_2 || <abbr title="1.950uf meassured onboard so maybe not accurate">'''Capacitor'''</abbr> to ground
| 20 || V_CAP_2 || 1.950uf '''Capacitor''' to ground (meassured onboard so maybe not accurate)
|-
|-
| 21 || {{cellcolors|#007700}} BATT_CHARGE_SETPOINT || Resistor (labeled '''R1''') to pull-down resistor (labeled '''R2''') and to DP transistor (labeled '''Q1'''). Controlled by Toshiba '''T6UN6EFG pin 41'''
| 21 || <abbr title="named ISET1 in the datasheet of the texas instrument BKO used in the prototype PP1 board">BATT_CHARGE_MODE</abbr> || Blue resistor to ground (labeled R2), and to blue 2.67K resistor (labeled R1) then to '''DP''' transistor (labeled Q1) (and the transistor base is connected to Toshiba '''T6UN6EFG, pin 41''')
|-
|-
| 22 || {{cellcolors|#ff9933}} V_STBY || '''Standby power rail''' output. ('''TP11''' in VX4 boards) with a capacitor to ground
| 22 || {{cellcolors|#ff9933}} V_STBY || '''2.8V standby''' shared rail for Toshiba, BT, PS button, LED's, EEPROM, etc... (and connected to '''TP11''' in VX4 boards)
|-
|-
| 23 || {{cellcolors|#ff9933}} V_SENSORS || '''Sensors power rail''' output. ('''TP12''' in VX4 boards) with a capacitor to ground
| 23 || {{cellcolors|#ff9933}} V_SENSORS || '''2.8V for accelerometer and gyroscope''' (Switched, no voltage in standby). (and connected to '''TP12''' in VX4 boards)
|-
|-
| 24 || {{cellcolors|#ff9933}} V_STICKS || '''Sticks power rail''' output. ('''TP13''' in VX4 boards) with a capacitor to ground
| 24 || {{cellcolors|#ff9933}} V_STICKS || '''2.8V for 4x stick pots''' (Switched, no voltage in standby). (and connected to '''TP13''' in VX4 boards)
|}
|}
*Notes
*Notes
**This component seems to provide several voltages for the BT module that i could not identify, probably are for the different components inside the BT module
**This component seems to provide with several voltages to the BT module that i could not identify... probably are for the different components inside the BT module
**The connections named in the table BT_POWER_ON and STICKS_POWER_ON with the toshiba T6UN6EFG could have two purposes, either to provide voltages for the subcircuits inside toshiba T6UN6EFG, or to allow the toshiba T6UN6EFG to send control signals to switch the low voltage power rails (marked in orange in te table). This is a big blind shoot though, based in how some groups of connections are grouped at the toshiba T6UN6EFG side (see the [[Template:Toshiba T6UN6EFG Pinout]])
**The connections with the toshiba controller probably are to provide voltages for the subcircuits inside it. There must be at least one exception because the toshiba is the "boss" of the board so it needs to be able to send some controll signal to this component to enable/disable power rails and things like that
**The toshiba T6UN6EFG (pin 4) is connected to the battery + pin so it should work even if the texas instruments SN89062 is disabled, is unknown how much of the internal circuits of the toshiba T6UN6EFG are enabled by pin 4, but there are some other subcircuits of the toshiba T6UN6EFG that are powered by the standby power rail generated by the instruments SN89062 (the V_STBY pin in the table). The importance of this details is at logic level in the way the circuit works and who is the "boss" of the board
**<strike>The toshiba controller probably is connected to the battery + or/and the 5V USB (so it should work even if this component is disabled because this one is a slave), is just i have not tryed to find all the pins of the toshiba chip</strike>, wrong, the toshiba chip is not connected to battery/USB, it seems to be connected only to "low voltage" lines
**The battery power rail has 3 connections, to the battery + pin connector, to the Texas Instruments SN89062 pin 16 (there is a direct connection in between this two), and also connected to the T6UN6EFG pin 4 by using an intermediate 147K/190K diode ?, and another diode of the same value to ground. The point of this diodes is to protect the toshiba chip because the other side of the battery power rail can work in two modes, when the controller is working and the only power source is the battery then the battery power rail provides power to the toshiba T6UN6EFG and Texas Instruments SN89062, and when the USB cable is connected then the Texas Instruments SN89062 checks the battery charge and starts the recharge, this recharge is made by using variable voltages (if the battery is very empty the voltage is higher and at the end of the chargue it starts reducing the intensity), the toshiba T6UN6EFG cant work with this variable voltages (other than using this voltage values as a check to know how the charge process is being made in a very accurate way), so the diodes seems to work as a barrier to stop that variable voltage to reach the toshiba T6UN6EFG
**All the boards has a component (with 5 pins) that protects the USB lines from [https://en.wikipedia.org/wiki/Electrostatic_discharge ESD] [https://en.wikipedia.org/wiki/Electromagnetic_interference EMI] and other kind of dangerous voltage effects that could appear on the USB data lines, is connected to the USB power rail (pin 4), standby power rail (pin 3), USB data + (pin 1), USB data - (pin 5), and to ground (pin 2). In some of the board models (the ones that has that side of the board printed such V2.5) it can be seen is labeled D1 (diode 1, the first and most important diode of the board), the component is listed in [https://www.electronicproducts.com/Sony_Playstation_3-whatsinside_text-10.aspx this link] as one of the parts of the PP4 boards and is marked 500 (when looking at a photo of a PP4 board search for the component labeled D1, and marked 500, next to the USB connector), sadly i could not find a accurate datasheet of it (if someone finds something please post it), but is something close to [http://www.syncpower.com/datasheet/SPE6V8UN.pdf this] (dual) or [https://assets.nexperia.com/documents/data-sheet/BZA800AVL_SERIES.pdf this] (quad). The component is actually a diode array made either with standard or [https://en.wikipedia.org/wiki/Transient-voltage-suppression_diode TVS diodes]. It can be defined as something such... "multichannel ESD protection diode array" (the 2 channels are the USB data lines + and -, and the 2 voltages are the USB or battery power sources). In VX4 version of the board this diode is marked N13, in VX5 N1W, in PP1 prototype (and PP4) 500, in VX7 N1D ?


----
----


=== Sticks control ===
=== Sticks ===


==== Texas Instruments YA018 ====
==== Texas Instruments YA018 ====
<div style="float:right">[[File:Texas Instruments YA018.jpg|200px|thumb|right|Texas Instruments YA018]]<br>[[File:Texas Instruments YA018 pinout.jpg|200px|thumb|right|Texas Instruments YA018 pinout]]<br>[[File:3-pins pots interconnections.jpg|200px|thumb|right|3-pins pots interconnections]]</div>
<div style="float:right">[[File:Texas Instruments YA018.jpg|200px|thumb|right|Texas Instruments YA018]]<br>[[File:Texas Instruments YA018 pinout.jpg|200px|thumb|right|Texas Instruments YA018 pinout]]</div>
16 pins. Used in PP4 boards (the first retail sixaxis models)
*Texas Instruments TS3A5018 TSSOP package
*Texas Instruments TS3A5018 TSSOP package
*http://www.ti.com/product/TS3A5018
*http://www.ti.com/product/TS3A5018
*http://www.ti.com/lit/ds/symlink/ts3a5018.pdf
*http://www.ti.com/lit/ds/symlink/ts3a5018.pdf
Used in PP4 boards (the first retail sixaxis models)


The TS3A5018 is a quad single-pole-double-throw ([https://en.wikipedia.org/wiki/Switch#Contact_terminology SPDT]) bidirectional solid-state analog switch
The TS3A5018 is a quad single-pole-double-throw ([https://en.wikipedia.org/wiki/Switch#Contact_terminology SPDT]) bidirectional solid-state analog switch
Line 859: Line 657:
| 1 || {{cellcolors|#555555|#ffffff}} IN || To Toshiba '''T6UN*EFG pin 11''' ?
| 1 || {{cellcolors|#555555|#ffffff}} IN || To Toshiba '''T6UN*EFG pin 11''' ?
|-
|-
| 2 || {{cellcolors|#cc9966}} NC1 || LX pot pin 2 (and missing capacitor C40 to ground in MSU PP4.0 5 boards)
| colspan="3" {{cellcolors|lightgrey}}
|-
| 3 || {{cellcolors|#aa7744}} NO1 ||
|-
|-
| 4 || {{cellcolors|#885522}} COM1 || TP20 ?
| 2 || NC1 ||  
|-
|-
| 5 || {{cellcolors|#cc9966}} NC2 || LY pot pin 2 (and missing capacitor C39 to ground in MSU PP4.0 5 boards)
| 3 || NO1 ||  
|-
|-
| 6 || {{cellcolors|#aa7744}} NO2 ||
| 4 || COM1 ||  
|-
| 7 || {{cellcolors|#885522}} COM2 || TP19 ?
|-
| 8 || {{cellcolors|#000000|#ffffff}} GND ||  To '''ground'''
|-
|-
| colspan="3" {{cellcolors|lightgrey}}
| colspan="3" {{cellcolors|lightgrey}}
|-
|-
| 9 || {{cellcolors|#885522}} COM3 || (and TP22 in MSU PP4.0 11 boards)
| 5 || NC2 ||  
|-
|-
| 10 || {{cellcolors|#aa7744}} NO3 || somewhere... (and TP58 in PP4.0 5 boards ?)
| 6 || NO2 ||  
|-
|-
| 11 || {{cellcolors|#cc9966}} NC3 || RX pot pin 2 (and missing capacitor C41 to ground in MSU PP4.0 11 boards)
| 7 || COM2 ||  
|-
|-
| 12 || {{cellcolors|#885522}} COM4 || TP21 ?
| colspan="3" {{cellcolors|lightgrey}}
|-
|-
| 13 || {{cellcolors|#aa7744}} NO4 ||  
| 8 || {{cellcolors|#000000|#ffffff}} GND || To '''ground'''
|-
|-
| 14 || {{cellcolors|#cc9966}} NC4 || RY pot pin 2 (and missing capacitor C42 to ground in MSU PP4.0 11 boards)
| colspan="3" {{cellcolors|lightgrey}}
|-
|-
| 15 || {{cellcolors|#000000|#ffffff}} <abbr title="it seems to be grounded in the photos availables to keep it permanently enabled">EN</abbr> || To '''ground'''
| 9 || COM3 || (and TP22 in MSU PP4.0 11 boards)
|-
|-
| 16 || {{cellcolors|#ff9933}} <abbr title="if this pin is connected to one of the switched power rails it can be turned ON/OFF by this pin">V_STICKS ?</abbr> || and C32 capacitor to ground in MSU PP4.0 11 boards
| 10 || NO3 ||  
|}
 
==== Toshiba 763 and 5W54 ====
<div style="float:right">[[File:Toshiba 763.jpg|200px|thumb|left|Toshiba 763 in a V2 2.14 board<br>next to the right stick Y axis pot]][[File:Toshiba 5W54.jpg|200px|thumb|right|Toshiba 5W54 in a V3.5X board<br>next to the right stick Y axis pot]]<br>[[File:Toshiba 5W54 pinout.jpg|200px|thumb|right|Toshiba 5W54 pinout]]</div>
8 pins. Used in V2, V2.5, VX, and V3.5X boards (the toshiba 763 is a rare variant used in V2 2.14 boards only)
*Toshiba TC75W54. Dual [https://en.wikipedia.org/wiki/Operational_amplifier op-amp], [http://chrisgammell.com/how-does-an-op-amp-work-part-1/ 1], [http://chrisgammell.com/how-an-op-amp-works-part-2/ 2]
*http://eu.mouser.com/ProductDetail/Toshiba/TC75W54FULF/?qs=sGAEpiMZZMuUbyQTl9BuV9cSxkqkD8zDF7KXFJxjfe4%3D
*http://www.mouser.com/ds/2/408/TC75W54FU_datasheet_en_19980528-760812.pdf
*[http://www.1688eric.com/en/product.aspx?id=381896 this]
 
TC75W54 is a [https://en.wikipedia.org/wiki/CMOS CMOS] [https://en.wikipedia.org/wiki/Operational_amplifier operational amplifier] with low supply voltage and low supply current
 
{| class="wikitable"
|-
|-
! Pin !! Name !! Notes
| 11 || NC3 || RX pot pin 2 (and missing capacitor C41 to ground in MSU PP4.0 11 boards)
|-
|-
| 1 || {{cellcolors|#885522}} X_OUT || To toshiba T6UN*EFG pin ? (and TP30 in V2, V2.5, VX boards. TP22 in V3.5X board)
| colspan="3" {{cellcolors|lightgrey}}
|-
|-
| 2 || {{cellcolors|#cc9966}} POT_X_2 ? || Precission resistors and thermistor (RT3 for left stick, RT4 for right stick) to stick X axis pot pin 2 ?, and <abbr title="the traces cant be followed in the photos, in some models seems to do some kind of loop, and in others seems to go far away maybe to the toshiba T6UN*EFG">something weird</abbr>
| 12 || COM4 ||  
|-
|-
| 3 || {{cellcolors|#cc9966}} POT_X_1 ? || Precission resistor to stick X axis pot pin 1 ?
| 13 || NO4 ||  
|-
|-
| 4 || {{cellcolors|#000000|#ffffff}} GND ? ||  
| 14 || NC4 || RY pot pin 2 (and missing capacitor C42 to ground in MSU PP4.0 11 boards)
|-
|-
| 5 || {{cellcolors|#cc9966}} POT_Y_1 ? || Precission resistor to stick Y axis pot pin 1 ?
| colspan="3" {{cellcolors|lightgrey}}
|-
|-
| 6 || {{cellcolors|#cc9966}} POT_Y_2 ? || Precission resistors and thermistor (RT2 for left stick, RT5 for right stick) to stick Y axis pot pin 2 ?, and <abbr title="the traces cant be followed in the photos, in some models seems to do some kind of loop, and in others seems to go far away maybe to the toshiba T6UN*EFG">something weird</abbr>
| 15 || {{cellcolors|#000000|#ffffff}} <abbr title="it seems to be grounded in the photos availables to keep it permanently enabled">EN</abbr> || To '''ground'''
|-
|-
| 7 || {{cellcolors|#885522}} Y_OUT || To toshiba T6UN6EFG pin ? (and TP29 in V2, V2.5, VX boards. TP21 in V3.5X board)
| 16 || {{cellcolors|#ff9933}} <abbr title="if this pin is connected to one of the switched power rails it can be turned ON/OFF by this pin">V_STICKS ?</abbr> || and C32 capacitor to ground in MSU PP4.0 11 boards
|-
| 8 || {{cellcolors|#ff9933}} V_STICKS ? || the pin seems connected with a wide trace that goes to the closest pot pin 3 (and TP13 in V3.5X board... probably the V_STICKS rail)
|}
|}


There are 2 components like this one in the boards where are used, every one of them is for an stick, is connected to that stick and the toshiba main controller to send the values of the X and Y axis of that stick, this two lines uses to have a testpoit
<!--
 
damn, i just noticed there is a mistake since begining the first time i copyed the pinout from the datasheet, switches 3 and 4 are inverted, and i used some of that ones comparing them with the photos to imagine the purpose of the other pins so high chances there are others wrong... the lines, pins of other components, and tespoints involved in this circuit dedicated to the sticks are the ones i been messing with, promise, is just at this point i think are connected in a different way
The 763 is a rare variant used only in MSU V2 2.14 boards, the only notable difference is the connections named <abbr title="the traces cant be followed in the photos, in some models seems to do some kind of loop, and in others seems to go far away maybe to the toshiba T6UN*EFG">something weird</abbr> in the pinout table are located in pins 3 and 5 (instead of pins 2 and 6), other than that there are no differences, is exactly the same component
 
Since this revision of the board the stick pots has 4 pins each (pole_1, pole_2, v_sticks, gnd) in that order from left to right (previous models has sticks with 3 pins pots)
 
In [http://www.alps.com/products/e/category_multi.html ALPS] webpage are only available sticks with 3 pins pots, there are two posible explains for this, maybe ALPS manufactured the sticks without pots and sony ordered this special version of the pots to other company then sony asembled the pots and sticks together.... or... ALPS made an special production of sticks with 4 pins pots. anyway, this pots with 4 pins are a bit special
 
In the boards where this component is present (or his replacement upgraded versions) every stick has two pots (to meassure rotations of X and Y axis of that stick), and every pot has 2 pins that are carrying the signals related with the rotation of the axis (pin 1 and 2 of the pot). This signals are voltages, but there is also another pin of the pot that has an additional voltage (pin 3). Inside the pot there are two separated voltages, this seems to create a magnetic field with a [https://en.wikipedia.org/wiki/Magnetoresistance magnetoresistive effect]. Also this allowed them (in further versions of the pots) to separate the mobile parts inside the pot by an intermediary "seal" that prevents dust and degradation of the parts
 
So... this component is the initial version that gives support for this "special sticks with 4 pins pots"
 
==== Texas Instruments SN84001 ====
<div style="float:right">[[File:Texas Instruments SN84001.jpg|200px|thumb|right|Texas Instruments SN84001]]<br>[[File:Texas Instruments SN84001 subcircuits.jpg|400px|thumb|right|Texas Instruments SN84001 subcircuits]]</div>
28 pins. Used in VX3, and VX4 boards
 
This component is dedicated to controll the sticks, the internal circuits inside it has some kind of simmetry, the V_STICKS voltage is only used to enable it. VX3 and VX4 boards has 7 capacitor networks in total and this component uses 4 of them. The 3 resistors used in the subcircuits are colored in blue which seems to indicate that are high precision. There are no datasheets availables of this component in the manufacturer web


{| class="wikitable"
{| class="wikitable"
Line 945: Line 707:
! Pin !! Name !! Notes
! Pin !! Name !! Notes
|-
|-
| 1 || {{cellcolors|#000000|#ffffff}} GND || To '''ground'''
| 1 || {{cellcolors|#555555|#ffffff}} IN || To Toshiba '''T6UN*EFG pin 11''' ?
|-
| 2 || {{cellcolors|#555555|#ffffff}} SLAVES_RESET || Connected to Toshiba '''T6UN6EFG pin 11''', and <abbr title="47ohm">resistor network</abbr> to '''BT module''' (ALPS 413A pin 5 in VX3 and VX4 boards)
|-
| 3 || {{cellcolors|#ff9933}} V_STICKS || 2.8V Switched. Power for 4x Stick {{padlx}}{{padly}} {{padrx}} {{padry}} pots pin 3. (and '''TP13''' in VX3 and VX4 boards). This pin seems to be working simply as an ON/OFF signal
|-
|-
| colspan="3" {{cellcolors|lightgrey}}
| colspan="3" {{cellcolors|lightgrey}}
|-
|-
| 4 || {{cellcolors|#cc9966}} POT_LY_2 || Stick '''Left Y''' axis pot '''pin 2'''
| 2 || {{cellcolors|#79604e}} NC1 || To Toshiba '''T6UN*EFG pin 77''' ?. (and TP19 in MSU PP4.0 11 boards ?)
|-
|-
| 5 || {{cellcolors|#cc9966}} POT_LX_1 || Stick '''Left X''' axis pot '''pin 1'''
| 3 || {{cellcolors|#b6a091}} NO1 || To Toshiba '''T6UN*EFG pin 37''' ?
|-
|-
| 6 || {{cellcolors|#cc9966}} POT_RY_2 || Stick '''Right Y''' axis pot '''pin 2'''
| 4 || {{cellcolors|#b89882}} COM1 || LX pot pin 2 ?
|-
|-
| 7 || {{cellcolors|#cc9966}} POT_RX_1 || Stick '''Right X''' axis pot '''pin 1'''
| colspan="3" {{cellcolors|lightgrey}}
|-
|-
| colspan="3" {{cellcolors|lightgrey}}
| 5 || {{cellcolors|#79604e}} NC2 || To Toshiba '''T6UN*EFG pin 78''' ?. (and TP20 in MSU PP4.0 11 boards ?)
|-
|-
| 8 || {{cellcolors|#cc9966}} POT_LY_1 || Stick '''Left Y''' axis pot '''pin 1'''
| 6 || {{cellcolors|#b6a091}} NO2 || To Toshiba '''T6UN*EFG pin 38''' ?
|-
|-
| 9 || {{cellcolors|#cc9966}} POT_LX_2 || Stick '''Left X''' axis pot '''pin 2'''
| 7 || {{cellcolors|#b89882}} COM2 || LY pot pin 2 ?
|-
|-
| 10 || {{cellcolors|#cc9966}} POT_RY_1 || Stick '''Right Y''' axis pot '''pin 1'''
| colspan="3" {{cellcolors|lightgrey}}
|-
|-
| 11 || {{cellcolors|#cc9966}} POT_RX_2 || Stick '''Right X''' axis pot '''pin 2'''
| 8 || {{cellcolors|#000000|#ffffff}} GND || To '''ground'''
|-
|-
| colspan="3" {{cellcolors|lightgrey}}
| colspan="3" {{cellcolors|lightgrey}}
|-
|-
| 12 || {{cellcolors|#ffeecc|#ee8822}} STICKS_LOOP_1_COMMON ? || rowspan="8" | All this pins are connected with each others making two independant subcircuits<br>Pin 12 is connected with <abbr title="left and right sticks pots - related ?">15 and 16</abbr> by using several resistors and a [https://en.wikipedia.org/wiki/Thermistor NTC thermistor]. This subcircuit seems to be an [https://en.wikipedia.org/wiki/Inrush_current_limiter Inrush current limiter]<br>Pin 13 is connected with <abbr title="left and right sticks pots + related ?">14 and 17</abbr> by using several resistors
| 9 || {{cellcolors|#79604e}} NC3 || To Toshiba '''T6UN*EFG pin 79''' ?. (and TP21 in MSU PP4.0 11 boards ?)
|-
|-
| 13 || {{cellcolors|#ffeecc|#ee8822}} STICKS_LOOP_2_COMMON ?
| 10 || {{cellcolors|#b6a091}} NO3 || To Toshiba '''T6UN*EFG pin 39''' ?
|-
|-
| colspan="2" {{cellcolors|lightgrey}}
| 11 || {{cellcolors|#b89882}} COM3 || RX pot pin 2
|-
|-
| 14 || {{cellcolors|#ffeecc|#ee8822}} STICKS_LOOP_2_LOW_R ?
| colspan="3" {{cellcolors|lightgrey}}
|-
| 15 || {{cellcolors|#ffeecc|#ee8822}} STICKS_LOOP_1_LOW_R ?
|-
|-
| colspan="2" {{cellcolors|lightgrey}}
| 12 || {{cellcolors|#79604e}} NC4 || To Toshiba '''T6UN*EFG pin 80''' ?. (and TP22 in MSU PP4.0 11 boards ?)
|-
|-
| 16 || {{cellcolors|#ffeecc|#ee8822}} STICKS_LOOP_1_HIGH_R ?
| 13 || {{cellcolors|#b6a091}} NO4 || To Toshiba '''T6UN*EFG pin 40''' ?
|-
|-
| 17 || {{cellcolors|#ffeecc|#ee8822}} STICKS_LOOP_2_HIGH_R ?
| 14 || {{cellcolors|#b89882}} COM4 || RY pot pin 2
|-
|-
| colspan="3" {{cellcolors|lightgrey}}
| colspan="3" {{cellcolors|lightgrey}}
|-
|-
| 18 || {{cellcolors|#aa7744}} RY_V ? || <abbr title="located close to Toshiba T6UN6EFG pin 41 corner">Capacitor network</abbr> to ground, and <abbr title="46.6K located next to Toshiba T6UN6EFG pin 40 corner">resistor network</abbr> to Toshiba '''T6UN6EFG pin 40'''
| 15 || {{cellcolors|#000000|#ffffff}} <abbr title="it seems to be grounded in the photos availables so the chip is permanently in ON state">EN</abbr> || To '''ground'''
|-
|-
| 19 || {{cellcolors|#aa7744}} RX_V ? || <abbr title="located close to Toshiba T6UN6EFG pin 41 corner">Capacitor network</abbr> to ground, and <abbr title="46.6K located next to Toshiba T6UN6EFG pin 40 corner">resistor network</abbr> to Toshiba '''T6UN6EFG pin 39'''
| 16 || {{cellcolors|#ff9933}} <abbr title="if this is connected to one of the switched power rails, the chip can be turned ON/OFF by this pin">V </abbr>||
|}
-->
 
==== Toshiba 5W54 ====
<div style="float:right">[[File:Toshiba 5W54 pinout.jpg|200px|thumb|left|Toshiba 5W54 pinout]][[File:Toshiba 5W54.jpg|200px|thumb|right|Toshiba 5W54 in a VX3.5X board]]</div>
8 pins. Used in V2, V2.5, VX, and V3.5X boards
Toshiba TC75W54FU (bulky package) or TC75W54FK (slim package). Dual [https://en.wikipedia.org/wiki/Operational_amplifier op-amp], [http://chrisgammell.com/how-does-an-op-amp-work-part-1/ 1], [http://chrisgammell.com/how-an-op-amp-works-part-2/ 2]
*http://eu.mouser.com/ProductDetail/Toshiba/TC75W54FULF/?qs=sGAEpiMZZMuUbyQTl9BuV9cSxkqkD8zDF7KXFJxjfe4%3D
*http://www.mouser.com/ds/2/408/TC75W54FU_datasheet_en_19980528-760812.pdf
*[http://www.1688eric.com/en/product.aspx?id=381896 this]
*Same pinout than Unknown 763 below ?
 
{| class="wikitable"
|-
|-
| 20 || {{cellcolors|#aa7744}} LY_V ? || <abbr title="located close to Toshiba T6UN6EFG pin 41 corner">Capacitor network</abbr> to ground, and <abbr title="46.6K located next to Toshiba T6UN6EFG pin 40 corner">resistor network</abbr> to Toshiba '''T6UN6EFG pin 38'''
! Pin !! Name !! Notes
|-
|-
| 21 || {{cellcolors|#aa7744}} LX_V ? || <abbr title="located close to Toshiba T6UN6EFG pin 41 corner">Capacitor network</abbr> to ground, and <abbr title="46.6K located next to Toshiba T6UN6EFG pin 40 corner">resistor network</abbr> to Toshiba '''T6UN6EFG pin 37'''
| 1 || {{cellcolors|#79604e}} X_OUT || To toshiba T6UN6EFG pin ? (and TP30 in V2.5 boards, TP22 in VX3.5X board)
|-
|-
| colspan="3" {{cellcolors|lightgrey}}
| 2 || {{cellcolors|#b89882}} POT_X_1 ? || Precission resistors and thermistor (RT4) to stick X axis pot pin ? (is either pin 1 or 2 from the ALPS stick models with 4 pins)
|-
|-
| 22 || {{cellcolors|#885522}} RY ? || <abbr title="located close to Texas Instruments SN84001 pin 15 corner (traces are hidden under Toshiba T6UN6EFG)">Capacitor network</abbr> to ground, and to Toshiba '''T6UN6EFG pin 80'''. (and '''TP22''' in VX3 and VX4 boards)
| 3 || {{cellcolors|#b89882}} POT_X_2 ? || Precission resistor to stick X axis pot pin ? (is either pin 1 or 2 from the ALPS stick models with 4 pins)
|-
|-
| 23 || {{cellcolors|#885522}} RX ? || <abbr title="located close to Texas Instruments SN84001 pin 15 corner (traces are hidden under Toshiba T6UN6EFG)">Capacitor network</abbr> to ground, and to Toshiba '''T6UN6EFG pin 79'''. (and '''TP21''' in VX3 and VX4 boards)
| 4 || {{cellcolors|#000000|#ffffff}} GND ? ||  
|-
|-
| 24 || {{cellcolors|#885522}} LY ? || <abbr title="located close to Texas Instruments SN84001 pin 15 corner">Capacitor network</abbr> to ground, and to Toshiba '''T6UN6EFG pin 78'''. (and '''TP20''' in VX3 and VX4 boards)
| 5 || {{cellcolors|#b89882}} POT_Y_2 ? || Precission resistor to stick Y axis pot pin 2 ? (is either pin 1 or 2 from the ALPS stick models with 4 pins)
|-
|-
| 25 || {{cellcolors|#885522}} LX ? || <abbr title="located close to Texas Instruments SN84001 pin 15 corner">Capacitor network</abbr> to ground, and to Toshiba '''T6UN6EFG pin 77'''. (and '''TP19''' in VX3 and VX4 boards)
| 6 || {{cellcolors|#b89882}} POT_Y_1 ? || Precission resistors and thermistor (RT5) to stick Y axis pot pin 1 ? (is either pin 1 or 2 from the ALPS stick models with 4 pins)
|-
|-
| colspan="3" {{cellcolors|lightgrey}}
| 7 || {{cellcolors|#79604e}} Y_OUT || To toshiba T6UN6EFG pin ? (and TP29 in V2.5 boards, TP21 in VX3.5X board)
|-
| 26 || {{cellcolors|#000000|#ffffff}} GND || rowspan="3" | To '''ground'''
|-
| 27 || {{cellcolors|#000000|#ffffff}} GND
|-
|-
| 28 || {{cellcolors|#000000|#ffffff}} GND
| 8 || {{cellcolors|#ff9933}} V_STICKS ? || the pin seems connected with a wide trace that goes to the closest pot pin 3 (and TP13 in VX3.5X board... probably the V_STICKS rail)
|}
|}
*There are 2 components like this one in the boards where are used, every one of them is for an stick, and every one of them is connected to the toshiba main controller to send the values of the X and Y axis of that stick
*There are 2 testpoints in the lines connecting this component with the toshiba main controller (one for every axis * 2 sticks... does a total of 4 testpoints in between this components and the toshiba controller)
*The photo at the right belongs to the right stick of an VX3.5 board (with testpoints '''TP21''' and '''TP22'''), the empty solder holes next to it are the Y axis pot of the right stick
<div style="clear:both;"></div>
==== Unknown 763 ====
<div style="float:right">[[File:Unknown sticks 002 763.jpg|200px|thumb|left|Unknown sticks 763 (example 1)]][[File:Unknown sticks 003 763.jpg|200px|thumb|right|Unknown sticks 763 (example 2)]]</div>
8 pins. Used in V2 2.14 boards
This component is very interesting, is the reason why the sticks potentiometers has 4 pins since this model (previous models has sticks with 3 pins pots)
The quality of the sticks and the way they works has been discussed in other places with some controversy, in [http://www.alps.com/products/e/category_multi.html ALPS] webpage are only available sticks with 3 pins pots, but for sony they made an special production of sticks with 4 pins pots, this ones are a bit special


*The subcircuit seems to work this way, im going to use rounded numbers for the math calculations because the values could vary at the time was meassured (in the schematic image at right)
In the boards where this component is present (or his replacement upgraded versions) every stick has two potentiometers (to meassure rotations of X and Y axis), and every potentiometer has 4 pins. Two of the potentiometer pins are connected to this component and drives a voltage, but there is also another pin of the potentiometer that has a controll voltage. Inside the potentiometer there are two separated voltages, this seems to create a magnetic field with the [https://en.wikipedia.org/wiki/Hall_effect hall effect], also this allows to separate the mobile parts inside the potentiometer (because every one of them has a different voltage circuit) by an intermediary "seal" that prevents dust and degradation of the parts (there is no direct contact of metal-VS-metal)
**The resistance between pins inmediatly (in the first few miliseconds) when is powered up is:
***In between pin 12 and pin 15 = 35.8K + 6.70K = 42.7K
***In between pin 12 and pin 16 = 35.8K + 6.70K + 1K = 43.7K
***In between pin 13 and pin 14 = 42.7K
***In between pin 13 and pin 17 = 42.7K + 1K = 43.7K
**After some time has passed, the thermistor starts heating up, and its resistance decreases (not sure if down to zero), it works as a bypass for the 6.70K blue resistor
***In between pin 12 and pin 15 = 35.8K + <abbr title="this is the thermistor when is hot, working as a bypass">0K</abbr> = 35.8K
***In between pin 12 and pin 16 = 35.8K + <abbr title="this is the thermistor when is hot, working as a bypass">0K</abbr> + 1K = 36.8K
***Only this two lines decreases his resitance along time. The other lines (connected to pin 13) doesnt changes because doesnt have a thermistor


So the [https://en.wikipedia.org/wiki/Thermistor NTC thermistor] is working as a [https://en.wikipedia.org/wiki/Inrush_current_limiter Inrush current limiter] for pins 15 and 16. And this pins seems to be related with the negative pole of the potentiometers
So... this component is the initial version that gives support for this "special sticks with 4 pins pots", in this version there is one component for every stick (so the board has a total of 2). The connections are (for every one of them): 4 lines to the stick + 2 lines to toshiba controller (the raw X and Y signals). Also in between this lines there are some testpoints (to check normal working of this subcircuit output)


By comparing this chip with the previous Toshiba TC75W54 there are two important differences, most notable is the Toshiba TC75W54 doesnt have the pins dedicated to the sticks subcircuits loops (where the thermistor/s is/are located) but it seems are around it, the Toshiba TC75W54 has 4 thermistors dedicated to this loops and Texas Instruments SN84001 has only one (this is an improvement to reduce costs and to make the circuit more simple and efficient). The point is that loops seems to be similar, maybe not exactly the same but something close to it. The other big difference is the Toshiba TC75W54 doesnt have connections with Toshiba T6UN6EFG pins 37, 38, 39, 40 (but are used connected somewhere else)... most probably is this pins are related with the stick subcircuits loops too
<div style="clear:both;"></div>


==== Texas Instruments A6044A0 ====
==== Texas Instruments SN84001 ====
<div style="float:right">[[File:Texas Instruments A6044A0.jpg|200px|thumb|right|Texas Instruments A6044A0]]</div>
<div style="float:right">[[File:Texas Instruments SN84001.jpg|200px|thumb|right|Texas Instruments SN84001]]<br>[[File:Texas Instruments SN84001 subcircuits.jpg|400px|thumb|right|Texas Instruments SN84001 subcircuits]]</div>
48 pins. Used in VX5 boards
28 pins. Used in VX3, and VX4 boards


This is an three-in-one component, integrates power/sticks control, and the functions of the battery setpoint transistor used in other boards. Is the result of placing together all the circuits of Texas Instruments SN89062, SN84001, and the DP transistor
This component is dedicated to controll the sticks, the internal circuits inside it has some kind of simmetry, the V_STICKS voltage is only used to enable it. VX3 and VX4 boards has 7 capacitor networks in total and this component uses 4 of them. The 3 resistors used in the subcircuit are colored in blue which seems to indicate that are high precision. There are no datasheets availables of this component in the manufacturer web but most probably there is going to be some similar, at this point is needed to find some datasheet that matches a bit the pinout and the subcircuit explained here in wiki


{| class="wikitable"
{| class="wikitable"
Line 1,045: Line 814:
| 1 || {{cellcolors|#000000|#ffffff}} GND || To '''ground'''
| 1 || {{cellcolors|#000000|#ffffff}} GND || To '''ground'''
|-
|-
| 2 || {{cellcolors|#008800}} BATT_CHARGE_START ? || To Toshiba '''T6UN6EFG pin 43'''
| 2 || {{cellcolors|#555555|#ffffff}} SLAVES_RESET || Connected to Toshiba '''T6UN6EFG pin 11''', and <abbr title="47ohm">resistor network</abbr> to '''BT module''' (ALPS 413A pin 5 in VX3 and VX4 boards)
|-
|-
| 3 || {{cellcolors|#666666|#ffffff}} RESET_SWITCH || To <abbr title="when reset switch is pressed this pin is grounded">'''SW1'''</abbr>
| 3 || {{cellcolors|#ff9933}} V_STICKS || 2.8V Switched. Power for 4x Stick {{padlx}}{{padly}} {{padrx}} {{padry}} pots pin 3. (and '''TP13''' in VX3 and VX4 boards). This pin seems to be working simply as an ON/OFF signal
|-
|-
| 4 || {{cellcolors|#4477ff}} BT_POWER_CTRL ? || To Toshiba '''T6UN6EFG pin 13''' with a <abbr title="4x resistor network 47K to standby power rail, located next to the BT SPI testpoints in VX5">pull-up resistor</abbr> and capacitor to ground
| colspan="3" {{cellcolors|lightgrey}}
|-
|-
| 5 || {{cellcolors|#008800}} BATT_USB_POWER_GOOD ? || To Toshiba '''T6UN6EFG pin 42'''
| 4 || {{cellcolors|#b89882}} LY_2 || Stick '''Left Y''' axis pot '''pin 2'''
|-
|-
| 6 || {{cellcolors|#ff3333}} V_USB || '''USB power rail''' input ('''TP1''')...
| 5 || {{cellcolors|#b89882}} LX_1 || Stick '''Left X''' axis pot '''pin 1'''
|-
|-
| 7 || {{cellcolors|#ff9933}} V_BT ? || '''BT power rail''' output ('''TP11''') with a capacitor to ground. To '''BT module''' ALPS '''603A pin ?''' and <abbr title="through resistor and with pull-down resistor... see ALPS 603A pinout for more details">'''pin ?'''</abbr>
| 6 || {{cellcolors|#b89882}} RY_2 || Stick '''Right Y''' axis pot '''pin 2'''
|-
|-
| 8 || {{cellcolors|#ff9933}} V_MOTORS || '''Motors power rail''' output ('''TP8'''). To 2x '''"KEX"''' (<abbr title="or voltage regulators ?">transistors</abbr> ?, 5 pins) with capacitors to ground, and '''BM+1''' (Big Motor +), and '''SM+1''' (Small Motor +)
| 7 || {{cellcolors|#b89882}} RX_1 || Stick '''Right X''' axis pot '''pin 1'''
|-
|-
| 9 || {{cellcolors|lightgrey}} N/C ? || <abbr title="dissapears under the component">Not connected ?</abbr>
| colspan="3" {{cellcolors|lightgrey}}
|-
|-
| 10 || {{cellcolors|#009900}} BATT_CHARGE_STATUS_1 ? || To Toshiba '''T6UN6EFG, pin 44''' (and '''TP15''')
| 8 || {{cellcolors|#b89882}} LY_1 || Stick '''Left Y''' axis pot '''pin 1'''
|-
|-
| 11 || {{cellcolors|#009900}} BATT_CHARGE_STATUS_2 ? || To Toshiba '''T6UN6EFG, pin 45''' (and '''TP9''')
| 9 || {{cellcolors|#b89882}} LX_2 || Stick '''Left X''' axis pot '''pin 2'''
|-
|-
| 12 || {{cellcolors|#885522}} || <abbr title="located close to Texas Instruments A6044A0 pin 1 corner">4x capacitor network</abbr> to ground, and to Toshiba '''T6UN6EFG pin 77'''. (and '''TP19''')
| 10 || {{cellcolors|#b89882}} RY_1 || Stick '''Right Y''' axis pot '''pin 1'''
|-
|-
| 13 || {{cellcolors|#885522}} || <abbr title="located close to Texas Instruments A6044A0 pin 1 corner">4x capacitor network</abbr> to ground, and to Toshiba '''T6UN6EFG pin ?'''. (and '''TP?''')
| 11 || {{cellcolors|#b89882}} RX_2 || Stick '''Right X''' axis pot '''pin 2'''
|-
|-
| 14 || {{cellcolors|#885522}} || <abbr title="located close to Texas Instruments A6044A0 pin 1 corner">4x capacitor network</abbr> to ground, and to Toshiba '''T6UN6EFG pin ?'''. (and '''TP?''')
| colspan="3" {{cellcolors|lightgrey}}
|-
|-
| 15 || {{cellcolors|#885522}} || <abbr title="located close to Texas Instruments A6044A0 pin 1 corner">4x capacitor network</abbr> to ground, and to Toshiba '''T6UN6EFG pin 80'''. (and '''TP22''')
| 12 ||  || rowspan="7" | All this pins are connected with each others making two independant subcircuits<br>Pin 12 is connected with 15 and 16 by using several resistors and a [https://en.wikipedia.org/wiki/Thermistor NTC thermistor]. This subcircuit seems to be an [https://en.wikipedia.org/wiki/Inrush_current_limiter Inrush current limiter]<br>Pin 17 is connected with 13 and 14 by using several resistors
|-
|-
| 16 || {{cellcolors|#cc9966}} POT_LY_2 || Stick '''Left Y''' axis pot '''pin 2'''
| 13 ||  
|-
|-
| 17 || {{cellcolors|#cc9966}} POT_LX_1 || Stick '''Left X''' axis pot '''pin 1'''
| 14 ||  
|-
|-
| 18 || {{cellcolors|#cc9966}} POT_RY_2 || Stick '''Right Y''' axis pot '''pin 2'''
| colspan="2" {{cellcolors|lightgrey}}
|-
| 19 || {{cellcolors|#cc9966}} POT_RX_1 || Stick '''Right X''' axis pot '''pin 1'''
|-
| 20 || {{cellcolors|#cc9966}} POT_LY_1 || Stick '''Left Y''' axis pot '''pin 1'''
|-
| 21 || {{cellcolors|#cc9966}} POT_LX_2 || Stick '''Left X''' axis pot '''pin 2'''
|-
|-
| 22 || {{cellcolors|#cc9966}} POT_RY_1 || Stick '''Right Y''' axis pot '''pin 1'''
| 15 ||  
|-
|-
| 23 || {{cellcolors|#cc9966}} POT_RX_2 || Stick '''Right X''' axis pot '''pin 2'''
| 16 ||  
|-
|-
| 24 || <abbr title="something similar than Texas Instruments SN84001 pins 12, 13, 14, 15, 16, 17">Sticks subcircuits loops</abbr> || 47K resistor to... ? (two different places)
| 17 ||  
|-
|-
| colspan="3" {{cellcolors|lightgrey}}
| colspan="3" {{cellcolors|lightgrey}}
|-
|-
| 25 || <abbr title="something similar than Texas Instruments SN84001 pins 12, 13, 14, 15, 16, 17">Sticks subcircuits loops</abbr> ||
| 18 || {{cellcolors|#b6a091}} RY_V ? || <abbr title="located close to Toshiba T6UN6EFG pin 41 corner">Capacitor network</abbr> to ground, and <abbr title="46.6K located next to Toshiba T6UN6EFG pin 40 corner">resistor network</abbr> to Toshiba '''T6UN6EFG pin 40'''
|-
|-
| 26 || <abbr title="something similar than Texas Instruments SN84001 pins 12, 13, 14, 15, 16, 17">Sticks subcircuits loops</abbr> || 35.7K resistor to... ?
| 19 || {{cellcolors|#b6a091}} RX_V ? || <abbr title="located close to Toshiba T6UN6EFG pin 41 corner">Capacitor network</abbr> to ground, and <abbr title="46.6K located next to Toshiba T6UN6EFG pin 40 corner">resistor network</abbr> to Toshiba '''T6UN6EFG pin 39'''
|-
|-
| 27 || <abbr title="something similar than Texas Instruments SN84001 pins 12, 13, 14, 15, 16, 17">Sticks subcircuits loops</abbr> ||
| 20 || {{cellcolors|#b6a091}} LY_V ? || <abbr title="located close to Toshiba T6UN6EFG pin 41 corner">Capacitor network</abbr> to ground, and <abbr title="46.6K located next to Toshiba T6UN6EFG pin 40 corner">resistor network</abbr> to Toshiba '''T6UN6EFG pin 38'''
|-
|-
| 28 || <abbr title="something similar than Texas Instruments SN84001 pins 12, 13, 14, 15, 16, 17">Sticks subcircuits loops</abbr> || To <abbr title=".550M located next to the pin">4x Resistor network</abbr>, and... ?
| 21 || {{cellcolors|#b6a091}} LX_V ? || <abbr title="located close to Toshiba T6UN6EFG pin 41 corner">Capacitor network</abbr> to ground, and <abbr title="46.6K located next to Toshiba T6UN6EFG pin 40 corner">resistor network</abbr> to Toshiba '''T6UN6EFG pin 37'''
|-
|-
| 29 || <abbr title="something similar than Texas Instruments SN84001 pins 12, 13, 14, 15, 16, 17">Sticks subcircuits loops</abbr> || To <abbr title=".550M located next to the pin">4x Resistor network</abbr>, and... ?
| colspan="3" {{cellcolors|lightgrey}}
|-
|-
| 30 || {{cellcolors|#aa7744}} || <abbr title="located close to Toshiba T6UN6EFG pin 40 corner">4x capacitor network</abbr> (CN4) to ground, and <abbr title="47.6K located close to Toshiba T6UN6EFG pin 40 corner">4x resistor network</abbr> (RN7) to Toshiba '''T6UN6EFG pin 40'''
| 22 || {{cellcolors|#79604e}} RY ? || <abbr title="located close to Texas Instruments SN84001 pin 15 corner (traces are hidden under Toshiba T6UN6EFG)">Capacitor network</abbr> to ground, and to Toshiba '''T6UN6EFG pin 80'''. (and '''TP22''' in VX3 and VX4 boards)
|-
|-
| 31 || {{cellcolors|#aa7744}} || <abbr title="located close to Toshiba T6UN6EFG pin 40 corner">4x capacitor network</abbr> (CN4) to ground, and <abbr title="47.6K located close to Toshiba T6UN6EFG pin 40 corner">4x resistor network</abbr> (RN7) to Toshiba '''T6UN6EFG pin ?'''
| 23 || {{cellcolors|#79604e}} RX ? || <abbr title="located close to Texas Instruments SN84001 pin 15 corner (traces are hidden under Toshiba T6UN6EFG)">Capacitor network</abbr> to ground, and to Toshiba '''T6UN6EFG pin 79'''. (and '''TP21''' in VX3 and VX4 boards)
|-
|-
| 32 || {{cellcolors|#aa7744}} || <abbr title="located close to Toshiba T6UN6EFG pin 40 corner">4x capacitor network</abbr> (CN4) to ground, and <abbr title="47.6K located close to Toshiba T6UN6EFG pin 40 corner">4x resistor network</abbr> (RN7) to Toshiba '''T6UN6EFG pin ?'''
| 24 || {{cellcolors|#79604e}} LY ? || <abbr title="located close to Texas Instruments SN84001 pin 15 corner">Capacitor network</abbr> to ground, and to Toshiba '''T6UN6EFG pin 78'''. (and '''TP20''' in VX3 and VX4 boards)
|-
|-
| 33 || {{cellcolors|#aa7744}} || <abbr title="located close to Toshiba T6UN6EFG pin 40 corner">4x capacitor network</abbr> (CN4) to ground, and <abbr title="47.6K located close to Toshiba T6UN6EFG pin 40 corner">4x resistor network</abbr> (RN7) to Toshiba '''T6UN6EFG pin 37'''
| 25 || {{cellcolors|#79604e}} LX ? || <abbr title="located close to Texas Instruments SN84001 pin 15 corner">Capacitor network</abbr> to ground, and to Toshiba '''T6UN6EFG pin 77'''. (and '''TP19''' in VX3 and VX4 boards)
|-
|-
| 34 || {{cellcolors|#000000|#ffffff}} GND || To '''ground'''
| colspan="3" {{cellcolors|lightgrey}}
|-
|-
| 35 || {{cellcolors|#555555|#ffffff}} SLAVES_RESET || Connected to Toshiba '''T6UN6EFG pin 11''', and... ?
| 26 || {{cellcolors|#000000|#ffffff}} GND || rowspan="3" | To '''ground'''
|-
|-
| 36 || {{cellcolors|#000099|#FF4500}} POWER_BT_UNK ? ||
| 27 || {{cellcolors|#000000|#ffffff}} GND
|-
|-
| 37 || {{cellcolors|#000099|#FF4500}} POWER_BT_UNK ? ||
| 28 || {{cellcolors|#000000|#ffffff}} GND
|-
| 38 || {{cellcolors|#000099|#FF4500}} POWER_BT_UNK ? ||
|-
| 39 || {{cellcolors|#ff3333}} V_BATT ||
|-
| 40 || {{cellcolors|#aa7744}} STICKS_POWER_ON ? || To Toshiba '''T6UN6EFG pin 36'''
|-
| 41 || {{cellcolors|#000099|#FF4500}} POWER_BT_UNK ? || ALPS 603A pin 4, and 4x resistor network 47K to ground (next to the BT module SPI testpoints)
|-
| 42 || {{cellcolors|#007700}} BATT_CHARGE_SETPOINT_DP_BASE || To Toshiba '''T6UN6EFG pin 41'''
|-
| 43 || {{cellcolors|#007700}} BATT_CHARGE_SETPOINT_DP_COLLECTOR || 2.6K resistor to pin 45
|-
| 44 || {{cellcolors|#000000|#ff9933}} V_CAP_2 || (Big) <abbr title="1.840uf meassured onboard so maybe not accurate">'''Capacitor'''</abbr> to ground (C4)
|-
| 45 || {{cellcolors|#007700}} BATT_CHARGE_SETPOINT || <abbr title="zener diode ?... 0.444 with the anode connected to ground">Reverse current protection diode</abbr>, and 2.6K resistor to pin 43
|-
| 46 || {{cellcolors|#ff9933}} V_STBY  ||
|-
| 47 || {{cellcolors|#ff9933}} V_SENSORS ||
|-
| 48 || {{cellcolors|#ff9933}} V_STICKS ||
|}
|}


In VX5 board there are 2 capacitor networks composed by 4 capacitors packed together, all them are connected in between this component and the toshiba T6UN6EFG, a total of 8 lines related with the sticks
==== Texas Instruments A6044A0 ====
<div style="float:right">[[File:Texas Instruments A6044A0.jpg|200px|thumb|right|Texas Instruments A6044A0]]</div>
48 pins. Used in VX5 boards


This is the only version of the boards where there is not a transistor (usually marked as <abbr title="Acronym of a Digital Potentiometer ?">'''DP'''</abbr>) to set the resistance that controlls the battery charge speeds, taper, and other battery charge configurations, the reason why this component doesnt exists in VX5 is because is integrated inside Texas Instruments A6044A0. The way it works is 1) toshiba pin 41 sends the signal (that was connected to the base of a transistor in all the other board versions) to Texas Instruments A6044A0 pin 42. Then 2) the signal drives an internal transistor (or digital potentiometer ?) inside the Texas Instruments A6044A0 that has the emitter pin connected to ground, so pin 43 is totally (or partially with a variable resistance ?) connected to ground. Then 3) Texas Instruments A6044A0 pin 45 calculates the battery setpoint by meassuring the resistance in between pin 43 (ground) and 45. Pin 45 works exactly the same way than in other boards models, actually the values of the resistor and diode in between pin 43 and 45 are the same used in some other boards such VX4
This is an all-in-one component, it does the power and sticks controll
<div style="clear:both;"></div>


=== Stick types ===
==== Levers ====


==== ALPS sticks with 3 Pins pots (rev 1) ====
===== 3 Pins (old) =====
Used in PP1 (prototype), and PP4 (first sixaxis retail) boards
In older models


==== ALPS sticks with 4 Pins pots (rev 2 and 3 ?) ====
===== 4 Pins =====
Two rotational potentiometers (variable resistors) are positioned below eack stick to meassure X and Y displacement. Current flows constantly through each one, and the amount of current is determined by the amount of resistance. Resistance is increased or decreased based on the position of the stick in a range from 0V up to 2.8V with center point at 1.4V
Two rotational potentiometers (variable resistors) are positioned below eack stick to meassure X and Y displacement. Current flows constantly through each one, and the amount of current is determined by the amount of resistance. Resistance is increased or decreased based on the position of the stick in a range from 0V up to 2.8V with center point at 1.4V


Line 1,158: Line 902:
</gallery>
</gallery>


==== ALPS sticks with 3 Pins pots (rev 4 ?) ====
===== 3 Pins (new) =====
Used in VX6, VX7, VX8 boards
In newer models


----
----
Line 1,219: Line 963:
| 7 ||  ||  
| 7 ||  ||  
|-
|-
| 8 || {{cellcolors|#ff77bb}} SENSOR_ACCL_ ? || To Toshiba '''T6UN*EFG, pin ?'''
| 8 || {{cellcolors|#ffff66}} ACCL_AXIS ? || To Toshiba '''T6UN*EFG, pin ?'''
|-
|-
| 9 || {{cellcolors|#ff77bb}} SENSOR_ACCL_ ? || To Toshiba '''T6UN*EFG, pin ?'''
| 9 || {{cellcolors|#ffff66}} ACCL_AXIS ? || To Toshiba '''T6UN*EFG, pin ?'''
|-
|-
| 10 || {{cellcolors|#ff77bb}} SENSOR_ACCL_ ? || To Toshiba '''T6UN*EFG, pin ?'''
| 10 || {{cellcolors|#ffff66}} ACCL_AXIS ? || To Toshiba '''T6UN*EFG, pin ?'''
|}
|}


===== Analog Devices 330K =====
===== Analog Devices 330K =====
<div style="float:right">[[File:Analog Devices 330K.jpg|200px|thumb|right|Analog Devices 330K]]</div>
<div style="float:right">[[File:Analog Devices 330K.jpg|200px|thumb|right|Analog Devices 330K]][[Image:Analog Devices 330K pinout.jpg|500px|thumb|left|Analog Devices 330K pinout]]</div>
16 pins. Used in board MSU_PP4.0 9 only
Analog Devices ADXL330KCPZ, 3-Axis Accelerometer, ±3g, 1.8 → 3.6 V, LFCSP 16-Pin
*Analog Devices ADXL330KCPZ, 3-Axis Accelerometer, ±3g, 1.8 → 3.6 V, LFCSP 16-Pin
 
*http://www.analog.com/en/products/mems/accelerometers.html
*http://www.analog.com/en/products/mems/accelerometers.html
*http://uk.rs-online.com/web/c/semiconductors/sensor-ics/accelerometer-ics/?applied-dimensions=4294967128
*http://uk.rs-online.com/web/c/semiconductors/sensor-ics/accelerometer-ics/?applied-dimensions=4294967128
*http://uk.rs-online.com/web/p/accelerometer-ics/0412775/
*http://uk.rs-online.com/web/p/accelerometer-ics/0412775/
*http://docs-europe.electrocomponents.com/webdocs/0aa7/0900766b80aa75b6.pdf


Only used in MSU_PP4.0 9 model
{| class="wikitable"
{| class="wikitable"
|-
|-
! Pin !! Name !! Notes
! Pin !! Name !! Notes
|-
|-
| 1 || {{cellcolors|lightgrey}} N/C || Not connected
| 1 || ||  
|-
|-
| 2 || <abbr title="When this pin is set to Vs, an electrostatic force is exerted on the accelerometer beam. The resulting movement of the beam allows the user to test if the accelerometer is functional. This ST pin may be left open circuit or connected to common (COM) in normal use">Self Test</abbr> || It cant be seen in the photos but most probably this function is disabled
| 2 || ||  
|-
|-
| 3 || {{cellcolors|#000000|#ffffff}} GND || To '''ground'''
| 3 || ||  
|-
|-
| 4 || {{cellcolors|lightgrey}} N/C || Not connected
| 4 || ||  
|-
|-
| 5 || {{cellcolors|#000000|#ffffff}} GND || rowspan="3" | To '''ground'''
| 5 || ||  
|-
|-
| 6 || {{cellcolors|#000000|#ffffff}} GND
| 6 || ||  
|-
|-
| 7 || {{cellcolors|#000000|#ffffff}} GND
| 7 || ||  
|-
|-
| 8 || {{cellcolors|#ff77bb}} SENSOR_ACCL_Z || To a testpoint, then resistor and capacitor to ground, then to another testpoint, then to Toshiba '''T6UN6EFG, pin ?'''
| 8 || ||  
|-
|-
| 9 || {{cellcolors|lightgrey}} N/C || Not connected
| 9 || ||  
|-
|-
| 10 || {{cellcolors|#ff77bb}} SENSOR_ACCL_Y || To a testpoint, then resistor and capacitor to ground, then to another testpoint, then to Toshiba '''T6UN6EFG, pin ?'''
| 10 || ||  
|-
|-
| 11 || {{cellcolors|lightgrey}} N/C || Not connected
| 11 || ||  
|-
|-
| 12 || {{cellcolors|#ff77bb}} SENSOR_ACCL_X || To a testpoint, then resistor and capacitor to ground, then to another testpoint, then to Toshiba '''T6UN6EFG, pin ?'''
| 12 || ||  
|-
|-
| 13 || {{cellcolors|lightgrey}} N/C || Not connected
| 13 || ||  
|-
|-
| 14 || {{cellcolors|#ff9933}} V_SENSORS || rowspan="2" | To '''sensors power''' rail
| 14 || ||  
|-
|-
| 15 || {{cellcolors|#ff9933}} V_SENSORS
| 15 || ||  
|-
|-
| 16 || {{cellcolors|lightgrey}} N/C || Not connected
| 16 || ||  
|}
|}


Line 1,299: Line 1,043:
| 7 || {{cellcolors|#ff9933}} V_SENSORS || '''2.8V Switched'''. Power for accelerometer and gyroscope. and capacitor to ground. (and connected to '''TP12''' in VX4 boards)
| 7 || {{cellcolors|#ff9933}} V_SENSORS || '''2.8V Switched'''. Power for accelerometer and gyroscope. and capacitor to ground. (and connected to '''TP12''' in VX4 boards)
|-
|-
| 8 || {{cellcolors|#ff77bb}} SENSOR_ACCL_X || To a testpoint ('''TP33''' in VX4 boards), then 33K resistor and capacitor to ground, then to another testpoint ('''TP36''' in VX4 boards), then to Toshiba '''T6UN6EFG, pin 6'''
| 8 || {{cellcolors|#ffff66}} ACCL_X || To a testpoint ('''TP33''' in VX4 boards), then 33K resistor and capacitor to ground, then to another testpoint ('''TP36''' in VX4 boards), then to Toshiba '''T6UN6EFG, pin 6'''
|-
|-
| 9 || {{cellcolors|#ff77bb}} SENSOR_ACCL_Y || To a testpoint ('''TP32''' in VX4 boards), then 33K resistor and capacitor to ground, then to another testpoint ('''TP35''' in VX4 boards), then to Toshiba '''T6UN6EFG, pin 7'''
| 9 || {{cellcolors|#ffff66}} ACCL_Y || To a testpoint ('''TP32''' in VX4 boards), then 33K resistor and capacitor to ground, then to another testpoint ('''TP35''' in VX4 boards), then to Toshiba '''T6UN6EFG, pin 7'''
|-
|-
| 10 || {{cellcolors|#ff77bb}} SENSOR_ACCL_Z || To a testpoint ('''TP34''' in VX4 boards), then 33K resistor and capacitor to ground, then to another testpoint ('''TP37''' in VX4 boards), then to Toshiba '''T6UN6EFG, pin 8'''
| 10 || {{cellcolors|#ffff66}} ACCL_Z || To a testpoint ('''TP34''' in VX4 boards), then 33K resistor and capacitor to ground, then to another testpoint ('''TP37''' in VX4 boards), then to Toshiba '''T6UN6EFG, pin 8'''
|-
|-
| 11 || {{cellcolors|#000000|#ffffff}} GND || To '''ground'''
| 11 || {{cellcolors|#000000|#ffffff}} GND || To '''ground'''
Line 1,324: Line 1,068:
| 1 || {{cellcolors|lightgrey}} N/C ? ||  
| 1 || {{cellcolors|lightgrey}} N/C ? ||  
|-
|-
| 2 || {{cellcolors|#ff77bb}} SENSOR_ACCL_ ? || To Toshiba '''T6UN6EFG, pin ?'''
| 2 || {{cellcolors|#ffff66}} ACCL_AXIS ? || To Toshiba '''T6UN6EFG, pin ?'''
|-
|-
| 3 || {{cellcolors|#ff77bb}} SENSOR_ACCL_ ? || To Toshiba '''T6UN6EFG, pin ?'''
| 3 || {{cellcolors|#ffff66}} ACCL_AXIS ? || To Toshiba '''T6UN6EFG, pin ?'''
|-
|-
| 4 || {{cellcolors|#ff77bb}} SENSOR_ACCL_ ? || To Toshiba '''T6UN6EFG, pin ?'''
| 4 || {{cellcolors|#ffff66}} ACCL_AXIS ? || To Toshiba '''T6UN6EFG, pin ?'''
|-
|-
| 5 || {{cellcolors|#000000|#ffffff}} GND ? ||  
| 5 || {{cellcolors|#000000|#ffffff}} GND ? ||  
Line 1,377: Line 1,121:
| 6 || {{cellcolors|#000000|#ffffff}} GND
| 6 || {{cellcolors|#000000|#ffffff}} GND
|-
|-
| 7 || {{cellcolors|#ff77bb}} SENSOR_ACCL_Y || To a testpoint ('''TP32''' in VX4 boards), then 33K resistor and capacitor to ground, then to another testpoint ('''TP35''' in VX4 boards), then to Toshiba '''T6UN6EFG, pin 7'''
| 7 || {{cellcolors|#ffff66}} ACCL_Y || To a testpoint ('''TP32''' in VX4 boards), then 33K resistor and capacitor to ground, then to another testpoint ('''TP35''' in VX4 boards), then to Toshiba '''T6UN6EFG, pin 7'''
|-
|-
| 8 || {{cellcolors|#ff77bb}} SENSOR_ACCL_X || To a testpoint ('''TP33''' in VX4 boards), then 33K resistor and capacitor to ground, then to another testpoint ('''TP36''' in VX4 boards), then to Toshiba '''T6UN6EFG, pin 6'''
| 8 || {{cellcolors|#ffff66}} ACCL_X || To a testpoint ('''TP33''' in VX4 boards), then 33K resistor and capacitor to ground, then to another testpoint ('''TP36''' in VX4 boards), then to Toshiba '''T6UN6EFG, pin 6'''
|-
|-
| 9 || {{cellcolors|#ff77bb}} SENSOR_ACCL_Z || To a testpoint ('''TP34''' in VX4 boards), then 33K resistor and capacitor to ground, then to another testpoint ('''TP37''' in VX4 boards), then to Toshiba '''T6UN6EFG, pin 8'''
| 9 || {{cellcolors|#ffff66}} ACCL_Z || To a testpoint ('''TP34''' in VX4 boards), then 33K resistor and capacitor to ground, then to another testpoint ('''TP37''' in VX4 boards), then to Toshiba '''T6UN6EFG, pin 8'''
|-
|-
| 10 || {{cellcolors|#000000|#ffffff}} GND || To '''ground'''
| 10 || {{cellcolors|#000000|#ffffff}} GND || To '''ground'''
Line 1,405: Line 1,149:
| 1 || {{cellcolors|#ff9933}} V_SENSORS ||  
| 1 || {{cellcolors|#ff9933}} V_SENSORS ||  
|-
|-
| 2 || ? ||  
| 2 || ||  
|-
|-
| 3 || {{cellcolors|#ff77bb}} SENSOR_GYRO ? ||  
| 3 || ||  
|-
|-
| 4 || {{cellcolors|#000000|#ffffff}} GND ||  
| 4 || {{cellcolors|#000000|#ffffff}} GND ||  
Line 1,453: Line 1,197:
| 2 || {{cellcolors|#000000|#ffffff}} GND || To '''ground'''
| 2 || {{cellcolors|#000000|#ffffff}} GND || To '''ground'''
|-
|-
| 3 || ? || To 3 small SMD components one of each color... to '''ground'''
| 3 || || To 3 small SMD components one of each color... to '''ground'''
|-
|-
| 4 || {{cellcolors|#000000|#ffffff}} GND || To '''ground'''
| 4 || {{cellcolors|#000000|#ffffff}} GND || To '''ground'''
|-
|-
| 5 || {{cellcolors|lightgrey}} N/C ? || Not connected ?
| 5 || || Not connected ?
|-
|-
| 6 || {{cellcolors|#ff77bb}} SENSOR_GYRO || To a testpoint ('''TP41''' in VX4 boards), then 33K resistor and capacitor to ground, then to another testpoint ('''TP40''' in VX4 boards), then to Toshiba '''T6UN6EFG, pin 9'''
| 6 || {{cellcolors|#ffff66}} GYRO || To a testpoint ('''TP41''' in VX4 boards), then 33K resistor and capacitor to ground, then to another testpoint ('''TP40''' in VX4 boards), then to Toshiba '''T6UN6EFG, pin 9'''
|-
|-
| 7 || {{cellcolors|lightgrey}} N/C ? || Not connected ?
| 7 || || Not connected ?
|-
|-
| 8 || {{cellcolors|#000000|#ffffff}} GND || To '''ground'''
| 8 || {{cellcolors|#000000|#ffffff}} GND || To '''ground'''
Line 1,467: Line 1,211:
| 9 || {{cellcolors|#ff9933}} V_SENSORS || '''2.8V Switched'''. Power for accelerometer and gyroscope. and capacitor to ground. (and connected to '''TP12''' in VX4 boards)
| 9 || {{cellcolors|#ff9933}} V_SENSORS || '''2.8V Switched'''. Power for accelerometer and gyroscope. and capacitor to ground. (and connected to '''TP12''' in VX4 boards)
|-
|-
| 10 || {{cellcolors|lightgrey}} N/C ? || Not connected ?
| 10 || || Not connected ?
|}
|}


----
----
=== Bluetooth ===
=== Bluetooth ===
http://www.alps.com/products/e/category_tuner.html
http://www.alps.com/products/e/category_tuner.html


==== 48 pins (13x19mm) ====
==== ALPS 103A ====
===== ALPS 103A =====
<div style="float:right">[[File:ALPS 103A.jpg|200px|thumb|right|ALPS 103A]]</div>
<div style="float:right">[[File:ALPS 103A.jpg|200px|thumb|right|ALPS 103A]]</div>
Used in boards: PP4
*Components inside ALPS 103A BT module:
**PCB = 6 layers
**Logic = SCEI/CSR CXD3262GG (BlueCore4 - External - Single Chip Bluetooth Solution, V2.0+EDR)
***CSR = Cambridge Silicon Radio (later adquired by qualcomm)
***External = It means this member of the "BlueCore4 family" uses an external memory (the 8Mb NOR chip listed below)
***http://www.iec.dk/products/csrchipsinfo.asp?id=41
***http://www.iec.dk/products/csrchipdescription.asp?C_D_Id=36
***http://www.nordfield.com/downloads/datasheets-components/BlueCore4.pdf
***https://cdn.sparkfun.com/datasheets/Wireless/Bluetooth/CSR-BC417-datasheet.pdf (BC417 external)
***http://www.czwtech.com/uploadfile/cfile/201211994421454.pdf (BC41B rom)
***https://hackaday.com/2014/05/18/firmware-for-cheap-bluetooth-modules/
**Memory = SST SST39VF800A-70-4I-M1QE (Flash - NOR, 8Mb (512k x 16), Multipurpose, 3.0V, 70nS)
***48-Ball Very-Very-Thin-Profile, Fine-Pitch Ball Grid Array (WFBGA) 4mm x 6mm
***http://www.microchip.com/wwwproducts/en/SST39VF800A
***http://ww1.microchip.com/downloads/en/DeviceDoc/25001A.pdf
**Crystal = 26MHz
**Capacitors count = 26
**Inductors count = 2
**Resistors count = 2
<div style="clear:both;"></div>
<div style="clear:both;"></div>


*SPI
==== ALPS 203A ====
**The SPI port can be used for system debugging. It can also be used for programming the Flash memory
**The DFU boot loader must be loaded into the Flash device before the UART or USB interfaces can be used. This initial flash programming can be done via the SPI
 
*UART
**BlueCore4-External UART interface provides a simple mechanism for communicating with other serial devices using the RS232 protocol. Four signals are used to implement the UART function. When BlueCore4-External is connected to another digital device, UART_RX and UART_TX transfer data between the two devices. The remaining two signals, UART_CTS and UART_RTS, can be used to implement RS232 hardware flow control where both are active low indicators
**http://www.summitdata.com/blog/uart-flow-control-rtscts-necessary-proper-operation-wireless-modules/
**http://simmonmt.blogspot.com.es/2011/05/rtscts-handshaking-and-waveforms.html
 
===== ALPS 203A =====
<div style="float:right">[[File:ALPS 203A.jpg|200px|thumb|right|ALPS 203A]]</div>
<div style="float:right">[[File:ALPS 203A.jpg|200px|thumb|right|ALPS 203A]]</div>
Used in boards: V2
<div style="clear:both;"></div>
<div style="clear:both;"></div>


===== ALPS 502A =====
==== ALPS 303A ====
Used in "some" [[Wireless Keypad]] boards
 
==== 40 pins (12x15mm) ====
===== ALPS 303A =====
<div style="float:right">[[File:ALPS 303A.jpg|200px|thumb|right|ALPS 303A]]</div>
<div style="float:right">[[File:ALPS 303A.jpg|200px|thumb|right|ALPS 303A]]</div>
Used in boards: V2.5, VX
Used in VX boards
<div style="clear:both;"></div>
<div style="clear:both;"></div>


===== ALPS 113A =====
==== ALPS 413A ====
Used in boards: V3.5X 1.14 only, seems to be a variant of the ALPS 413A below
 
===== ALPS 413A =====
<div style="float:right">[[File:ALPS 413A.jpg|200px|thumb|right|ALPS 413A]]</div>
<div style="float:right">[[File:ALPS 413A.jpg|200px|thumb|right|ALPS 413A]]</div>
Used in boards: V3.5X, VX3, VX4, and "some" [[Move Navigation Controller]] boards
Used in V3.5X, VX3, VX4 boards, and "some" [[Move Navigation Controller]] boards


The pin numbers can be seen on V3.5X boards
The pin numbers can be seen on V3.5X boards
Line 1,537: Line 1,241:
! Pin # !! Name !! Port !! Description
! Pin # !! Name !! Port !! Description
|-
|-
| 1 || {{cellcolors|#000000|#ffffff}} GND_SHIELD || || To ground (corner solder point for the interferences metal shield)
| 1 || {{cellcolors|#000000|#ffffff}} GND || || To ground
|-
|-
| 2 || {{cellcolors|#ff9933}} V_BT_DETECT ? ||  || Diode to ground, and 15K resistor to pin 3
| 2 || {{cellcolors|#ff9933}} V_WEIRD ? ||  || Diode to ground, and 15K resistor to pin 3
|-
|-
| 3 || {{cellcolors|#ff9933}} V_BT ? ||  || To Texas Instruments SN89062 pin 7, and to TP10 in VX4 boards
| 3 || {{cellcolors|#ff9933}} V_BT ? ||  || To Texas Instruments SN89062 pin 7, and to TP10 in VX4 boards
Line 1,547: Line 1,251:
| 5 || {{cellcolors|#555555|#ffffff}} SLAVES_RESET ||  || To <abbr title="47ohm in VX4 boards">resistor network</abbr>, and then to Texas Instruments SN84001 pin 2 and to Toshiba T6UN6EFG pin 11 in VX4 boards
| 5 || {{cellcolors|#555555|#ffffff}} SLAVES_RESET ||  || To <abbr title="47ohm in VX4 boards">resistor network</abbr>, and then to Texas Instruments SN84001 pin 2 and to Toshiba T6UN6EFG pin 11 in VX4 boards
|-
|-
| 6 || {{cellcolors|#6699ff}} <abbr title="either... TX, RX, RTS, or CTS">BT_UART_2</abbr> ? ||  ||  To Toshiba T6UN6EFG pin 15 through <abbr title="47ohm in VX4 boards">resistor network</abbr>
| 6 || {{cellcolors|#ffddcc}} BT_UART_RX ? ||  ||  To Toshiba T6UN6EFG pin 15 through <abbr title="47ohm in VX4 boards">resistor network</abbr>
|-
|-
| 7 || {{cellcolors|#6699ff}} <abbr title="either... TX, RX, RTS, or CTS">BT_UART_4</abbr> ? ||  || To Toshiba T6UN6EFG pin 17
| 7 || {{cellcolors|#ffddcc}} BT_UART_UNK ? ||  || To Toshiba T6UN6EFG pin 17
|-
|-
| 8 || {{cellcolors|#6699ff}} <abbr title="either... TX, RX, RTS, or CTS">BT_UART_1</abbr> ? ||  || To Toshiba T6UN6EFG pin 14 through <abbr title="33ohm in VX4 boards">resistor</abbr>
| 8 || {{cellcolors|#ffddcc}} BT_UART_SELECT ? ||  || To Toshiba T6UN6EFG pin 14 through <abbr title="33ohm in VX4 boards">resistor</abbr>
|-
|-
| 9 || {{cellcolors|#6699ff}} <abbr title="either... TX, RX, RTS, or CTS">BT_UART_3</abbr> ? ||  || To Toshiba T6UN6EFG pin 16 through <abbr title="47ohm in VX4 boards">resistor network</abbr>
| 9 || {{cellcolors|#ffddcc}} BT_UART_TX ? ||  || To Toshiba T6UN6EFG pin 16 through <abbr title="47ohm in VX4 boards">resistor network</abbr>
|-
|-
| 10 || {{cellcolors|#e0e0e0}} USB_DATA+ ||  || USB connector through <abbr title="23ohm in VX4 boards">resistor</abbr> (and TP3 in VX4 boards)
| 10 || {{cellcolors|#e0e0e0}} USB_DATA+ ||  || USB connector through <abbr title="23ohm in VX4 boards">resistor</abbr> (and TP3 in VX4 boards)
Line 1,559: Line 1,263:
| 11 || {{cellcolors|#33ff33}} USB_DATA- ||  || USB connector through <abbr title="23ohm in VX4 boards">resistor</abbr> (and TP2 in VX4 boards)
| 11 || {{cellcolors|#33ff33}} USB_DATA- ||  || USB connector through <abbr title="23ohm in VX4 boards">resistor</abbr> (and TP2 in VX4 boards)
|-
|-
| 12 || {{cellcolors|#000000|#ffffff}} GND_SHIELD || || To ground (corner solder point for the interferences metal shield)
| 12 || {{cellcolors|#000000|#ffffff}} GND || || To ground
|-
| colspan="4" {{cellcolors|lightgrey}}
|-
| 13 || {{cellcolors|#000000|#ffffff}} GND_SHIELD || || To ground (corner solder point for the interferences metal shield)
|-
|-
| 14 || {{cellcolors|#3366ff}} BT_UNK_1 || || To Toshiba T6UN6EFG pin 18
| 13 || {{cellcolors|#000000|#ffffff}} GND || || To ground
|-
|-
| 15 || {{cellcolors|#000099|#FF4500}} POWER_BT_UNK ? ||  || To Texas Instruments SN89062 pin 19
| 14 || ||  || To Toshiba T6UN6EFG pin 18
|-
|-
| 16 || {{cellcolors|#000099|#FF4500}} POWER_BT_UNK ? ||  || To Texas Instruments SN89062 pin 14
| 15 || ||  || To Texas Instruments SN89062 pin 19
|-
|-
| 17 || {{cellcolors|#ccccff|#000099}} <abbr title="either... CSB, CLK, MOSI, or MISO">BT_SPI_3</abbr> ? ||  || To debug missing connector in PP4 and V2 boards... or... TP49 in V3.5X boards... or... TP76 in VX3 boards... or unlabeled testpoint in VX4, VX5, VX6 boards
| 16 || ||  || To Texas Instruments SN89062 pin 14
|-
|-
| 18 || {{cellcolors|#ccccff|#000099}} <abbr title="either... CSB, CLK, MOSI, or MISO">BT_SPI_2</abbr> ? ||  || To debug missing connector in PP4 and V2 boards... or... TP48 in V3.5X boards... or... TP75 in VX3 boards... or unlabeled testpoint in VX4, VX5, VX6 boards
| 17 || {{cellcolors|#e0c0b0}} UNK_SERVICE_CONNECTOR_1 ||  || To missing connector in PP4 and V2 boards... or... TP49 in V3.5X boards... or... TP76 in VX3 boards... or unlabeled testpoint in VX4, VX5, VX6 boards
|-
|-
| 19 || {{cellcolors|#ccccff|#000099}} <abbr title="either... CSB, CLK, MOSI, or MISO">BT_SPI_4</abbr> ? ||  || To debug missing connector in PP4 and V2 boards... or... TP50 in V3.5X boards... or... TP77 in VX3 boards... or unlabeled testpoint in VX4, VX5, VX6 boards
| 18 || {{cellcolors|#e0c0b0}} UNK_SERVICE_CONNECTOR_2 ||  || To missing connector in PP4 and V2 boards... or... TP48 in V3.5X boards... or... TP75 in VX3 boards... or unlabeled testpoint in VX4, VX5, VX6 boards
|-
|-
| 20 || {{cellcolors|#000000|#ffffff}} GND_SHIELD || || To ground (corner solder point for the interferences metal shield)
| 19 || {{cellcolors|#e0c0b0}} UNK_SERVICE_CONNECTOR_3 || || To missing connector in PP4 and V2 boards... or... TP50 in V3.5X boards... or... TP77 in VX3 boards... or unlabeled testpoint in VX4, VX5, VX6 boards
|-
|-
| colspan="4" {{cellcolors|lightgrey}}
| 20 || {{cellcolors|#000000|#ffffff}} GND || || To ground
|-
|-
| 21 || {{cellcolors|#000000|#ffffff}} GND_SHIELD || || To ground (corner solder point for the interferences metal shield)
| 21 || {{cellcolors|#000000|#ffffff}} GND || || To ground
|-
|-
| 22 || {{cellcolors|#ccccff|#000099}} <abbr title="either... CSB, CLK, MOSI, or MISO">BT_SPI_1</abbr> ? ||  || To debug missing connector in PP4 and V2 boards... or... TP47 in V3.5X boards... or... TP74 in VX3 boards... or unlabeled testpoint in VX4, VX5, VX6 boards
| 22 || {{cellcolors|#e0c0b0}} UNK_SERVICE_CONNECTOR_4 ||  || To missing connector in PP4 and V2 boards... or... TP47 in V3.5X boards... or... TP74 in VX3 boards... or unlabeled testpoint in VX4, VX5, VX6 boards
|-
|-
| 23 || {{cellcolors|#000000|#ffffff}} GND || || To ground
| 23 || {{cellcolors|#000000|#ffffff}} GND || || To ground
|-
|-
| 24 || {{cellcolors|lightgrey}} N/C ? ||  || Not connected ?
| 24 || ||  ||  
|-
|-
| 25 || {{cellcolors|#ff9933}} V_STBY ||  || To Texas Instruments SN89062 pin 22
| 25 || {{cellcolors|#ff9933}} V_STBY ||  || To Texas Instruments SN89062 pin 22
Line 1,595: Line 1,295:
| 27 || {{cellcolors|#ff9933}} V_STBY ||  || To Texas Instruments SN89062 pin 22
| 27 || {{cellcolors|#ff9933}} V_STBY ||  || To Texas Instruments SN89062 pin 22
|-
|-
| 28 || {{cellcolors|#3366ff}} BT_UNK_2 ||  || Toshiba T6UN6EFG pin 19
| 28 || ||  || Toshiba T6UN6EFG pin 19
|-
|-
| 29 || {{cellcolors|lightgrey}} N/C ? ||  || Not connected ?
| 29 || ||  ||  
|-
|-
| 30 || {{cellcolors|#000000|#ffffff}} GND || || To ground
| 30 || {{cellcolors|#000000|#ffffff}} GND || || To ground
|-
|-
| 31 || {{cellcolors|lightgrey}} N/C ? ||  || Not connected ?
| 31 || ||  ||  
|-
| 32 || {{cellcolors|#000000|#ffffff}} GND_SHIELD || || To ground (corner solder point for the interferences metal shield)
|-
|-
| colspan="4" {{cellcolors|lightgrey}}
| 32 || {{cellcolors|#000000|#ffffff}} GND || || To ground
|-
|-
| 33 || {{cellcolors|#000000|#ffffff}} GND_SHIELD || || To ground (corner solder point for the interferences metal shield)
| 33 || {{cellcolors|#000000|#ffffff}} GND || || To ground
|-
|-
| 34 || {{cellcolors|#44bbbb}} ANTENNA ||  || Antenna
| 34 || {{cellcolors|#aaffff}} ANT ||  || Antenna
|-
|-
| 35 || {{cellcolors|#000000|#ffffff}} GND || || To ground
| 35 || {{cellcolors|#000000|#ffffff}} GND || || To ground
|-
|-
| 36 || {{cellcolors|lightgrey}} N/C ? ||  || Not connected ?
| 36 || ||  ||  
|-
|-
| 37 || {{cellcolors|#000099|#FF4500}} POWER_BT_UNK ? ||  || To Texas Instruments SN89062 pin 13
| 37 || ||  || To Texas Instruments SN89062 pin 13
|-
|-
| 38 || {{cellcolors|#000099|#FF4500}} POWER_BT_UNK ? ||  || To Texas Instruments SN89062 pin 15
| 38 || ||  || To Texas Instruments SN89062 pin 15
|-
|-
| 39 || {{cellcolors|lightgrey}} N/C ? ||  || Not connected ?
| 39 || ||  ||  
|-
|-
| 40 || {{cellcolors|#000000|#ffffff}} GND_SHIELD || || To ground (corner solder point for the interferences metal shield)
| 40 || {{cellcolors|#000000|#ffffff}} GND || || To ground
|}
|}


===== ALPS 503A =====
==== ALPS 503A ====
Used in "some" [[Move Motion Controller]] boards
Used in "some" [[Move Motion Controller]] boards


==== 48 pins (11x11mm) ====
==== ALPS 603A ====
===== ALPS 603A =====
<div style="float:right">[[File:ALPS 603A.jpg|200px|thumb|left|ALPS 603A]][[File:ALPS 603A VX7.jpg|200px|thumb|right|ALPS 603A VX7]]</div>
<div style="float:right">[[File:ALPS 603A.jpg|200px|thumb|left|ALPS 603A]][[File:ALPS 603A VX7.jpg|200px|thumb|right|ALPS 603A VX7]]</div>
Used in boards: VX5, VX6, VX7
Used in VX5, VX6, VX7 boards
 
Without knowing what is inside, just based on the size of this BT module... the logic "chip" inside probably is a bluecore4-ROM based model (or 5-ROM series), this means the flash memory is integrated inside the "chip"
 
The pin numbers can be seen on VX7 boards
 
{|class="wikitable"
|+ALPS 603A Pinout
! Pin # !! Name !! Description
|-
| 1 || Not connected || In VX 5 0.06
|-
| 2 || {{cellcolors|#000000|#ffffff}} GND || To '''ground'''
|-
| 3 || {{cellcolors|#ffff99|#FF4500}} BUTTON_DIGITAL_PLAYSTATION || In VX 5 0.06: To Toshiba '''T6UN6EFG pin 68''' (which is also PS button) with a <abbr title="4x resistor network RN5 100K to ground">pull-down resistor</abbr>
|-
| 4 || {{cellcolors|#000099|#FF4500}} POWER_BT_UNK ? || To Texas Instruments '''A6044A0 pin 41''' with a <abbr title="4x resistor network 47K to ground, located next to the BT SPI testpoints in VX5">pull-down resistor</abbr>
|-
| 5 || {{cellcolors|#3366ff}} BT_UNK_2 || In VX 5 0.06: To To Toshiba ''' T6UN6EFG pin 19''' with a <abbr title="4x resistor network RN5 100K to ground">pull-down resistor</abbr>
|-
| 6 || {{cellcolors|#ff9933}} V_STBY || To Texas Instruments '''A6044A0 pin 46''' ('''TP10''' in VX5)
|-
| 7 || {{cellcolors|#ff9933}} V_STBY || To Texas Instruments '''A6044A0 pin 46''' ('''TP10''' in VX5)
|-
| 8 || {{cellcolors|#000000|#ffffff}} GND || To '''ground'''
|-
| 9 || Not connected || In VX 5 0.06
|-
| 10 || {{cellcolors|#000099|#FF4500}} POWER_BT_UNK ? || To Texas Instruments '''A6044A0 pin 38''' and capacitor to ground ('''C19''' in VX5)
|-
| 11 || {{cellcolors|#000099|#FF4500}} POWER_BT_UNK ? || To Texas Instruments '''A6044A0 pin 37''' with a <abbr title="4x resistor network 47K to standby power rail, located next to the BT SPI testpoints in VX5">pull-up resistor</abbr> and capacitor to ground ('''C15''' in VX5)
|-
| 12 || {{cellcolors|#000000|#ffffff}} <abbr title="Corner ground connected to the interferences metal shield">GND_SHIELD</abbr> || To '''ground'''
|-
| colspan="4" {{cellcolors|lightgrey}}
|-
| 13 || {{cellcolors|#000000|#ffffff}} <abbr title="Corner ground connected to the interferences metal shield">GND_SHIELD</abbr> || To '''ground'''
|-
| 14 || {{cellcolors|#3366ff}} BT_UNK_2 || To Toshiba '''T6UN6EFG pin 19'''; In VX 5 0.06 to ground only
|-
| 15 || {{cellcolors|#000000|#ffffff}} GND || To '''ground'''
|-
| 16 || {{cellcolors|#000000|#ffffff}} GND || To '''ground'''
|-
| 17 || {{cellcolors|#44bbbb}} ANTENNA || Antenna
|-
| 18 || {{cellcolors|#000000|#ffffff}} GND || To '''ground'''
|-
| 19 || {{cellcolors|#000000|#ffffff}} GND || To '''ground'''
|-
| 20 || {{cellcolors|#000099|#FF4500}} POWER_BT_UNK ? || To Texas Instruments '''A6044A0 pin 36''' with a <abbr title="4x resistor network 47K to ground, located next to the BT SPI testpoints in VX5">pull-down resistor</abbr> and capacitor to ground ('''C18''' in VX5)
|-
| 21 || {{cellcolors|#ff9933}} V_BT ? || Through 15k resistor with a <abbr title="4x resistor network RN5 100K to ground">pull-down resistor</abbr> creating 15k to 100k voltage divider to Texas Instruments '''A6044A0 pin 7''' ('''TP11''' in VX5)
|-
| 22 || {{cellcolors|#000000|#ffffff}} GND || To '''ground'''
|-
| 23 || {{cellcolors|#ff9933}} V_STBY || To Texas Instruments '''A6044A0 pin 46''' ('''TP10''' in VX5)
|-
| 24 || {{cellcolors|#000000|#ffffff}} <abbr title="Corner ground connected to the interferences metal shield">GND_SHIELD</abbr> || To '''ground'''
|-
| colspan="4" {{cellcolors|lightgrey}}
|-
| 25 || {{cellcolors|#000000|#ffffff}} <abbr title="Corner ground connected to the interferences metal shield">GND_SHIELD</abbr> || To '''ground'''
|-
| 26 || {{cellcolors|#555555|#ffffff}} SLAVES_RESET || <abbr title="4x resistor network 47ohm">Resistor network</abbr> ('''RN4''' in VX5 and VX7) to Toshiba '''T6UN6EFG pin 11'''... <abbr title="to Texas Instruments A6044A0 pin 35 ?">and...</abbr> ?
|-
| 27 || {{cellcolors|#000000|#ffffff}} GND || To '''ground''' (in VX5). <abbr title="Most probably this pin of the resistor network in VX7 is ground">Or to 4x resistor network ('''RN4''' in VX7)</abbr>
|-
| 28 || {{cellcolors|#77aaff}} <abbr title="either... TX, RX, RTS, or CTS">BT_UART_3</abbr> ? || <abbr title="4x resistor network 47ohm">Resistor network</abbr> ('''RN4''' in VX5 and VX7) to Toshiba '''T6UN6EFG pin 16'''
|-
| 29 || {{cellcolors|#3366ff}} BT_UNK_1 || To Toshiba '''T6UN6EFG pin 18'''
|-
| 30 || {{cellcolors|#6699ff}} <abbr title="either... TX, RX, RTS, or CTS">BT_UART_2</abbr> ? || <abbr title="4x resistor network 47ohm">Resistor network</abbr> ('''RN4''' in VX5 and VX7) to Toshiba '''T6UN6EFG pin 15'''
|-
| 31 || {{cellcolors|#6699ff}} <abbr title="either... TX, RX, RTS, or CTS">BT_UART_4</abbr> ? || To Toshiba '''T6UN6EFG pin 17'''
|-
| 32 || {{cellcolors|#6699ff}} <abbr title="either... TX, RX, RTS, or CTS">BT_UART_1</abbr> ? || <abbr title="33ohm in VX5 boards">Resistor</abbr> ('''R11''' in VX5, '''R10''' in VX7) to Toshiba '''T6UN6EFG pin 14'''
|-
| 33 || Not connected || In VX 5 0.06
|-
| 34 || {{cellcolors|#e0e0e0}} USB_DATA+ || To '''USB connector''' through 22ohm <abbr title="To pass the USB compliance tests is required a series termination resistor in the data line. This resistor also works as an ElectroMagnetic Interference filter">'''termination/EMI''' resistor</abbr> ('''R7''' in VX7), and to <abbr title="ElectroStatic Discharge filter, 5 pins">'''ESD filter pin 1'''</abbr>. (and '''TP3''' in VX5, unlabeled testpoint in VX7)
|-
| 35 || {{cellcolors|#33ff33}} USB_DATA- || To '''USB connector''' through 22ohm <abbr title="To pass the USB compliance tests is required a series termination resistor in the data line. This resistor also works as an ElectroMagnetic Interference filter">'''termination/EMI''' resistor</abbr> ('''R9''' in VX7), and to <abbr title="ElectroStatic Discharge filter, 5 pins">'''ESD filter pin 5'''</abbr>. (and '''TP2''' in VX5, unlabeled testpoint in VX7)
|-
| 36 || {{cellcolors|#000000|#ffffff}} <abbr title="Corner ground connected to the interferences metal shield">GND_SHIELD</abbr> || To '''ground'''
|-
| colspan="4" {{cellcolors|lightgrey}}
|-
| 37 || Not connected || In VX 5 0.06
|-
| 38 || {{cellcolors|#ff9933}} V_BT ? || To Texas Instruments '''A6044A0 pin 7''' ('''TP11''' in VX5) and to other BT pin 21 through 15k resistor and then through 100K resistor network RN5 to ground
|-
| 39 || {{cellcolors|#000000|#ffffff}} GND || To '''ground'''
|-
| 40 || {{cellcolors|#ccccff|#000099}} BT_SPI_SS || ('''TP25''' in VX7)
|-
| 41 || {{cellcolors|#ccccff|#000099}} BT_SPI_MOSI || ('''TP24''' in VX7)
|-
| 42 || {{cellcolors|#ccccff|#000099}} BT_SPI_CLK || ('''TP26''' in VX7)
|-
| 43 || {{cellcolors|#ccccff|#000099}} BT_SPI_MISO || ('''TP23''' in VX7)
|-
| 44 || {{cellcolors|#000000|#ffffff}} GND || To '''ground'''
|-
| 45 || Not connected || In VX 5 0.06
|-
| 46 || Not connected || In VX 5 0.06
|-
| 47 || {{cellcolors|#000000|#ffffff}} GND || To '''ground'''
|-
| 48 || Not connected || In VX 5 0.06
|}
 
==== Onboard (not a module) ====
===== Cambridge Silicon Radio unknown =====
<div style="float:right">[[File:Cambridge Silicon Radio BT bluecore unknown.jpg|200px|thumb|right|Cambridge Silicon Radio BT bluecore unknown]]</div>
Used in boards: VX8 only
 
This version of the logic "chip" probably is pretty similar (or exactly the same) than the one used inside the previous ALPS 603A BT module, the difference is the crystal and the "chip" itself has been moved out of the "old" BT modules PCB, that BT module PCB had 6 layers in previous versions and the dualshock 3 PCB had 2 layers. To make this change posible the PCB of VX8 boards is multilayer (there are a lot of traces "hidden" connected to the BT "chip")
<!--Actually, VX8 board doesnt have a MCU (the toshiba main controller was removed, wtf)... this is very weird, it means everything is connected to the bluecore chip... so is doing a lot more than previous versions -->
<div style="clear:both;"></div>
<div style="clear:both;"></div>


Line 1,755: Line 1,333:
[[File:Dualshock 3 fake (leds light transpassing the plastic case).jpg|400px|thumb|right| Dualshock 3 fake (leds light transpassing the plastic case)]]
[[File:Dualshock 3 fake (leds light transpassing the plastic case).jpg|400px|thumb|right| Dualshock 3 fake (leds light transpassing the plastic case)]]


*The SONY logo on the top of a counterfeit controller will not be aligned correctly with a original controller.
*The SONY logo on the top of a counterfeit controller will not be aligned correctly with a originall controller.


*Different sticker label
*Different sticker label
Line 1,773: Line 1,351:
*Leds
*Leds
**The LEDs lights on the controller that signify which Player it is controlling will not be flush with the outside shell. Official controllers are relatively level all the way across. Some controllers may have minor protrusion of the LEDs, though this should not be significant.
**The LEDs lights on the controller that signify which Player it is controlling will not be flush with the outside shell. Official controllers are relatively level all the way across. Some controllers may have minor protrusion of the LEDs, though this should not be significant.
**When you turn on a counterfeit the controller, the flashing red lights on the outside will actually shine THROUGH the casing of the device, something that would never happen on an official product.
**When you turn on a counterfeit the controller, the flashing red lights on the outside will actually shine THROUGH the casing of the device, something that would never happen on an official product.  
**When battery is low on the counterfeit controllers, it may repeatedly show the low battery notification on your Playstation multiple times.


*Syncing
*Syncing
**If you have consistent trouble wirelessly syncing your controller to your PS3, the device may be counterfeit.
**If you have consistent trouble wirelessly syncing your controller to your PS3, the device may be counterfeit.
* No pressure-sensitive buttons, some games might not even go past the title screen. An example is Metal Gear 2/3 from the Metal Gear Solid HD collection, selecting any of those games will either get you stuck in the title screen (MGS2) or will not function properly (MGS3).


From: http://www.ps3hax.net/showthread.php?p=574042#post574042
From: http://www.ps3hax.net/showthread.php?p=574042#post574042
Line 1,815: Line 1,390:
* https://github.com/felis/USB_Host_Shield_2.0/wiki/PS3-Information
* https://github.com/felis/USB_Host_Shield_2.0/wiki/PS3-Information


== Nefarius tools for use of controller on PC ==
== Nefarius tools for PC ==
 
for use of controller on PC
BthPS3
 
* https://docs.nefarius.at/projects/BthPS3/ ( Windows 10/11 Bluetooth driver for DS3)
 
DsHidMini
 
* https://docs.nefarius.at/projects/DsHidMini/ (Windows 10/11 driver for DS3 with various different modes of operation: PCSX2 / DS4 Windows / SXS (Steam, RCPS3) / Xinput)
 
ScpToolkit - Discontinued
* https://github.com/nefarius/ScpToolkit (Windows Driver and XInput Wrapper for Sony DualShock 3/4 Controllers)
* https://github.com/nefarius/ScpToolkit (Windows Driver and XInput Wrapper for Sony DualShock 3/4 Controllers)
* [http://forums.pcsx2.net/Thread-ScpToolkit-XInput-Wrapper-aka-ScpServer-Reloaded ScpToolkit XInput Wrapper aka ScpServer Reloaded on forums.pcsx2.net]
* http://forums.pcsx2.net/Thread-ScpToolkit-XInput-Wrapper-aka-ScpServer-Reloaded
FireShock - Discontinued
* https://github.com/nefarius/FireShock
* https://github.com/nefarius/FireShock (Bluetooth is not supported yet, USB only as of 09/2017)
* http://forums.pcsx2.net/Thread-FireShock-native-USB-Windows-Driver-for-Sony-DualShock-Controllers
* [http://forums.pcsx2.net/Thread-FireShock-native-USB-Windows-Driver-for-Sony-DualShock-Controllers FireShock on forums.pcsx2.net]
* https://vigem.org/ (HIDUSB filter driver for Sony DualShock controllers)
* https://vigem.org/ (HIDUSB filter driver for Sony DualShock controllers)
* https://github.com/nefarius/ViGEm (Virtual Gamepad Emulation Framework)
* https://github.com/nefarius/ViGEm (Virtual Gamepad Emulation Framework)
Line 1,839: Line 1,404:


== Other ==
== Other ==
*nice PCB overview of revisions: http://forums.xbox-scene.com/lofiversion/index.php/t648322.html - offline forum
* nice PCB overview of revisions: http://forums.xbox-scene.com/lofiversion/index.php/t648322.html http://forums.xbox-scene.com/index.php?/topic/648322-ps3-controller-versions-and-tp-spots/ http://s50.photobucket.com/user/RDCXBG/library/PS3%20Six-Axis%20and%20DS3
*http://forums.xbox-scene.com/index.php?/topic/648322-ps3-controller-versions-and-tp-spots/ - offline forum
*http://s50.photobucket.com/user/RDCXBG/library/PS3%20Six-Axis%20and%20DS3 - RDC photobucket
*[http://www63.zippyshare.com/v/32870351/file.html sony-ps3-controller.pdf] - transcription of the (missing) RDC thread on (defunct) xbox-scene forum


{{Peripherals}}<noinclude>
{{Peripherals}}<noinclude>[[Category:Main]]</noinclude>
[[Category:Main]]
</noinclude>
Please note that all contributions to PS3 Developer wiki are considered to be released under the GNU Free Documentation License 1.2 (see PS3 Developer wiki:Copyrights for details). If you do not want your writing to be edited mercilessly and redistributed at will, then do not submit it here.
You are also promising us that you wrote this yourself, or copied it from a public domain or similar free resource. Do not submit copyrighted work without permission!

To protect the wiki against automated edit spam, we kindly ask you to solve the following hCaptcha:

Cancel Editing help (opens in new window)

Templates used on this page:

Retrieved from "http://www.psdevwiki.com/ps3/DualShock_3"