Psp Go Jigkick: Difference between revisions
Jump to navigation
Jump to search
| (11 intermediate revisions by one other user not shown) | |||
| Line 1: | Line 1: | ||
* | * Original info kindly provided by l_oliveira | ||
= How to | = How to Enter Service Mode (officially known as Manufacturing Mode) on PSP Go = | ||
Connecting a PSP Go | Connecting a PSP Go multi-use connector plug to a TTL serial adapter: | ||
* Pin 24 connected to any ground (see | * Pin 24 connected to any ground (see pin-out below for ground pins) | ||
* Pins 14 | * Pins 14 and 17 connected together for k-line communication with your favorite 1.8v level serial adapter | ||
* Serial adapter must have 1n4148 diode with line toward it's TX, other end tied to RX, and RX going to Go pins 14+17 | * Serial adapter must have a 1n4148 diode with line (cathode) toward it's TX, other end (anode) tied to RX, and RX going to Go pins 14+17 | ||
* Ground connected between Go and serial adapter | * Ground connected between Go and serial adapter | ||
* (optional) | * (optional) Pin 20 with 10K resistor to 5v power source and pin 22 directly connected to 5v power source | ||
Plug in modified connector to PSP Go while fully powered off (NOT in sleep mode), | Plug in your serial adapter to PC and set up [https://github.com/khubik2/pysweeper PySweeper] with the correct COM port for your adapter and the option for service mode selected. Plug in modified multi-use connector to PSP Go while fully powered off (NOT in sleep mode), SYSCON will begin serial communication with your serial adapter and enter service mode. | ||
= Explanation = | = Explanation of Pins used for Service Mode = | ||
* Pin | * Pin 14 is PSP Go TX | ||
* Pin | * Pin 17 is PSP Go RX | ||
* Pin 24 | * Pin 24 is SYSCON TOH0, enables serial communication when grounded | ||
* Pin 20 is Cradle Power Detect, enables charging/power from pin 22 | |||
* Pin 22 is 5v in | |||
= Full | = Full Multi-use Connector Pin-out = | ||
<pre> | <pre> | ||
01- GND | 01- GND | ||
02- ACCESSORY_USB_SUPPLY_3V3 | 02- ACCESSORY_USB_SUPPLY_3V3 (Used on N440 Converter Cable Adapter to power USB accessories) | ||
03- EXTERNAL_MIC_IN | 03- EXTERNAL_MIC_IN | ||
04- | 04- POMMEL BALL M1 (?) | ||
05- AUD_L | 05- AUD_L | ||
06- Backlight IC ball C1 (ext mic en?) | 06- Backlight IC ball C1 (ext mic en?) | ||
| Line 34: | Line 36: | ||
12- GND | 12- GND | ||
13- Pr / COMPOSITE_VIDEO | 13- Pr / COMPOSITE_VIDEO | ||
14- CABLE_TYPE_SENSE_1 (Used in jigkick | 14- CABLE_TYPE_SENSE_1 (Used in jigkick as TX) | ||
15- CABLE_TYPE_SENSE_2 | 15- CABLE_TYPE_SENSE_2 | ||
16- Y / S-VIDEO_Y | 16- Y / S-VIDEO_Y | ||
17- Backlight IC ball D4 (Used in jigkick | 17- Backlight IC ball D4 (Used in jigkick as RX) | ||
18- Backlight IC ball B2 | 18- Backlight IC ball B2 | ||
19- Cb / S-VIDEO_C | 19- Cb / S-VIDEO_C | ||
20- DET_5V_CRADLE ( | 20- DET_5V_CRADLE (Apply +5v through 10kOhm resistor to enable pin 22) | ||
21- DET_USB_CABLE_CONNECTED | 21- DET_USB_CABLE_CONNECTED | ||
22- 5V_INPUT | 22- 5V_INPUT (Apply +5v when enabled to charge battery or power board if no battery) | ||
23- Backlight IC ball A6 | 23- Backlight IC ball A6 | ||
24- | 24- SYSCON_TOH0 (Ground while powered off to enable jigkick) | ||
25- GND | 25- GND | ||
26- USB_D+ | 26- USB_D+ | ||
| Line 54: | Line 56: | ||
<gallery> | <gallery> | ||
File:GPEHSYqW8AAD6oC.jpg | |||
File:Photo_2023-08-16_19-32-24.jpg | File:Photo_2023-08-16_19-32-24.jpg | ||
File:Photo 2023-08-15 20-56-16.jpg | File:Photo 2023-08-15 20-56-16.jpg | ||
| Line 62: | Line 65: | ||
</gallery> | </gallery> | ||
* For pin numbering on cradle connector with text upside down: | * For pin numbering on cradle multi-use connector plug with text upside down: | ||
<pre> | <pre> | ||
Latest revision as of 20:08, 2 June 2024
- Original info kindly provided by l_oliveira
How to Enter Service Mode (officially known as Manufacturing Mode) on PSP Go[edit | edit source]
Connecting a PSP Go multi-use connector plug to a TTL serial adapter:
- Pin 24 connected to any ground (see pin-out below for ground pins)
- Pins 14 and 17 connected together for k-line communication with your favorite 1.8v level serial adapter
- Serial adapter must have a 1n4148 diode with line (cathode) toward it's TX, other end (anode) tied to RX, and RX going to Go pins 14+17
- Ground connected between Go and serial adapter
- (optional) Pin 20 with 10K resistor to 5v power source and pin 22 directly connected to 5v power source
Plug in your serial adapter to PC and set up PySweeper with the correct COM port for your adapter and the option for service mode selected. Plug in modified multi-use connector to PSP Go while fully powered off (NOT in sleep mode), SYSCON will begin serial communication with your serial adapter and enter service mode.
Explanation of Pins used for Service Mode[edit | edit source]
- Pin 14 is PSP Go TX
- Pin 17 is PSP Go RX
- Pin 24 is SYSCON TOH0, enables serial communication when grounded
- Pin 20 is Cradle Power Detect, enables charging/power from pin 22
- Pin 22 is 5v in
Full Multi-use Connector Pin-out[edit | edit source]
01- GND 02- ACCESSORY_USB_SUPPLY_3V3 (Used on N440 Converter Cable Adapter to power USB accessories) 03- EXTERNAL_MIC_IN 04- POMMEL BALL M1 (?) 05- AUD_L 06- Backlight IC ball C1 (ext mic en?) 07- GND 08- AUD_R 09- GND 10- ENABLE_AUDIO_MULTIOUT 11- GND 12- GND 13- Pr / COMPOSITE_VIDEO 14- CABLE_TYPE_SENSE_1 (Used in jigkick as TX) 15- CABLE_TYPE_SENSE_2 16- Y / S-VIDEO_Y 17- Backlight IC ball D4 (Used in jigkick as RX) 18- Backlight IC ball B2 19- Cb / S-VIDEO_C 20- DET_5V_CRADLE (Apply +5v through 10kOhm resistor to enable pin 22) 21- DET_USB_CABLE_CONNECTED 22- 5V_INPUT (Apply +5v when enabled to charge battery or power board if no battery) 23- Backlight IC ball A6 24- SYSCON_TOH0 (Ground while powered off to enable jigkick) 25- GND 26- USB_D+ 27- USB_D- 28- GND
Picture of Setup[edit | edit source]
- For pin numbering on cradle multi-use connector plug with text upside down:
1 4 7 ... gap in pins here 3 6 9 ... 2 5 8 ...
