Editing Psp Go Jigkick
Jump to navigation
Jump to search
The edit can be undone. Please check the comparison below to verify that this is what you want to do, and then publish the changes below to finish undoing the edit.
| Latest revision | Your text | ||
| Line 1: | Line 1: | ||
* Original info kindly provided by l_oliveira | * Original info kindly provided by l_oliveira | ||
= How to | = How to enter service mode (officially known as Manufacturing Mode) on PSP Go = | ||
Connecting a PSP Go multi-use connector plug to a TTL serial adapter: | Connecting a PSP Go multi-use connector plug to a TTL serial adapter: | ||
* Pin 24 connected to any ground (see pin-out below for ground pins) | * Pin 24 connected to any ground (see pin-out below for ground pins) | ||
* Pins 14 and 17 connected together for k-line communication with your favorite 1.8v level serial adapter | * Pins 14 and 17 connected together for k-line communication with your favorite 1.8v level serial adapter | ||
* Serial adapter must have | * Serial adapter must have 1n4148 diode with line (cathode) toward it's TX, other end (anode) tied to RX, and RX going to Go pins 14+17 | ||
* Ground connected between Go and serial adapter | * Ground connected between Go and serial adapter | ||
* (optional) Pin 20 with 10K resistor to 5v power source and pin 22 directly connected to 5v power source | * (optional) Pin 20 with 10K resistor to +5v power source and pin 22 directly connected to +5v power source | ||
Plug in your serial adapter to PC and set up | Plug in your serial adapter to PC and set up PySweeper with the correct COM port for your adapter and the option for service mode selected. Plug in modified multi-use connector to PSP Go while fully powered off (NOT in sleep mode), SYSCON will begin serial communication with your serial adapter and enter service mode. | ||
= Explanation of Pins used for Service Mode = | = Explanation of Pins used for Service Mode = | ||
| Line 18: | Line 18: | ||
* Pin 24 is SYSCON TOH0, enables serial communication when grounded | * Pin 24 is SYSCON TOH0, enables serial communication when grounded | ||
* Pin 20 is Cradle Power Detect, enables charging/power from pin 22 | * Pin 20 is Cradle Power Detect, enables charging/power from pin 22 | ||
* Pin 22 is 5v in | * Pin 22 is +5v in | ||
= Full Multi-use Connector Pin-out = | = Full Multi-use Connector Pin-out = | ||
| Line 42: | Line 42: | ||
18- Backlight IC ball B2 | 18- Backlight IC ball B2 | ||
19- Cb / S-VIDEO_C | 19- Cb / S-VIDEO_C | ||
20- DET_5V_CRADLE (Apply +5v | 20- DET_5V_CRADLE (Apply +5v to enable pin 22) | ||
21- DET_USB_CABLE_CONNECTED | 21- DET_USB_CABLE_CONNECTED | ||
22- 5V_INPUT | 22- 5V_INPUT | ||
23- Backlight IC ball A6 | 23- Backlight IC ball A6 | ||
24- SYSCON_TOH0 (Ground while powered off to enable jigkick) | 24- SYSCON_TOH0 (Ground while powered off to enable jigkick) | ||
| Line 56: | Line 56: | ||
<gallery> | <gallery> | ||
File:Photo_2023-08-16_19-32-24.jpg | File:Photo_2023-08-16_19-32-24.jpg | ||
File:Photo 2023-08-15 20-56-16.jpg | File:Photo 2023-08-15 20-56-16.jpg | ||