Editing Hardware Registers

Jump to navigation Jump to search
Warning: You are not logged in. Your IP address will be publicly visible if you make any edits. If you log in or create an account, your edits will be attributed to your username, along with other benefits.

The edit can be undone. Please check the comparison below to verify that this is what you want to do, and then publish the changes below to finish undoing the edit.

Latest revision Your text
Line 1: Line 1:
= Introduction =
= Introduction =


With the exception of interrupts, almost all the interaction with the PSP hardware is done through memory mapped IO (MMIO) accesses in the 0xBC000000~0xBFFFFFFF address range. The physical address of this range is actually 0x1C000000~0x1FFFFFFF, but we must OR in the 0x40000000 un-cached flag and the 0x80000000 kernel access flag. Knowing how to communicate with the hardware is vital to understanding the inner workings of the PSP.
On the PSP, except interruptions, almost all the interaction with the hardware is done through memory accesses to "hardware registers" located at the 0xBC000000~0xBFFFFFFF range (actually 0x1C000000~0x1FFFFFFF to which we add the 0x4 uncached flag and the 0x8 kernel flag). Which is the reason why documenting this is vital to understand the PSP hardware.


= 0xA7F00000: L2 cache =
= 0xA7F00000: L2 cache =
Line 451: Line 451:
Bits 6-11 = UART 0-5
Bits 6-11 = UART 0-5


Bits 12-15 = APB (Arm Peripheral Bus) Timer 0-3
Bits 12-15 = APB (?) 0-3


Bits 16-17 = Audio 0-1
Bits 16-17 = Audio 0-1


Bits 18 = LCD Controller
Bits 19-21 = ?


Bits 19 = PWM
Bit 22 = SIRCS (?)
 
Bits 20 = ?
 
Bits 21 = I2C
 
Bit 22 = SIRCS (Sony Serial Infra-Red Control)


Bit 23 = GPIO
Bit 23 = GPIO
Line 498: Line 492:
| 0xBC100064 || 4 || RW || SPI clock select
| 0xBC100064 || 4 || RW || SPI clock select
|-
|-
| 0xBC100068 || 4 || RW || Bits 0-7: PLL frequency
| 0xBC100068 || 4 || RW || 0xF - PLL get/set out select (PLL frequency?)
 
Bits 16-31: unknown, checked against by the iplloader, possibly related to jigkick
|-
|-
| 0xBC100070 || 4 || RW || Set Avc power
| 0xBC100070 || 4 || RW || Set Avc power
Line 506: Line 498:
| 0xBC100074 || 4 || RW || Unknown
| 0xBC100074 || 4 || RW || Unknown
|-
|-
| 0xBC100078 || 4 || RW || I/O enable
| 0xBC100078 || 4 || RW || I/O enable (?) (TODO: verify indices)
 
Bit 1 = EMCSM
 
Bit 2 = USB
 
Bit 3 = ATA


Bits 4-5 = MSIF
Bit 0 = NAND


Bit 6 = LCDC
Bit 1 = USB


Bits 7-8 = Audio
Bit 2 = ATA


Bit 9 = I2c
Bits 3-4 = Memstick Interface


Bit 10 = Sircs
Bit 5 = LCDC


Bit 11 = AudioClkout
Bit 6-7 = Audio


Bit 12 = Key (?)
Bit 8 = IIC


Bit 13 = PWM
Bit 9 = SIRCS


Bit 14 = ATA HDD
Bit 10 = Audio?


Bit 15 = TBD - needs more sysreg reversing
Bit 11 = KEY


Bits 16-21 = UART 0-5
Bit 12 = PWM


Bits 22-23 = TBD - needs more sysreg reversing
Bits 13-18 = UART
 
Bits 24-29 = SPI 0-5
 
Bits 30-31 = TBD - needs more sysreg reversing


Bits 19-24 = SPI
|-
|-
| 0xBC10007C || 4 || RW || Either GPIO pin enable, or GPIO pin direction
| 0xBC10007C || 4 || RW || Either GPIO pin enable, or GPIO pin direction
Line 873: Line 856:
|-
|-
|}
|}
= 0xBC700000: ? =


= 0xBC800000: DMACPlus =
= 0xBC800000: DMACPlus =
Line 1,595: Line 1,580:
Value 6 = unknown
Value 6 = unknown
|-
|-
| 0xBD800410 || 4 || RW || Set/get enabled connection interrupts (same bits as above)
| 0xBD800410 || 4 || RW ||  
|-
| 0xBD800414 || 4 || RW || Unknown
|-
| 0xBD800418 || 4 || RW || Disabled endpoints interfaces (bits 0-8 = sending, and bits 16-24 = receiving?)
|-
| 0xBD80041C || 4 || RW || Unknown (possible value: 0)
|-
| 0xBD800504 || 4 || W? || Unknown
|-
| 0xBD800508 || 4 || W? || Unknown
|-
| 0xBD80050C || 4 || W? || Unknown
|-
| 0xBD800510 || 4 || W? || Unknown
|-
| 0xBD800514 || 4 || W? || Unknown
|-
|-
|}
|}


= 0xBD900000: EFlash (PSP Go only) =
= 0xBDE00000: KIRK =


{| class="wikitable"
{| class="wikitable"
Line 1,624: Line 1,593:
! Description
! Description
|-
|-
| 0xBD900004 || 4 || W? || Unknown, set to 0x04024002
| 0xBDE00000 || 4 || R || KIRK signature 'KIRK' (or 1?)
|-
|-
| 0xBD900010 || 4 || W? || Write 1 to reset
| 0xBDE00004 || 4 || R || KIRK version '0010' (or 1?)
|-
|-
| 0xBD900014 || 4 || W? || Unknown
| 0xBDE00008 || 4 || RW || Set to 1 on error by the command subroutine
|-
|-
| 0xBD900018 || 4 || W? || Unknown
| 0xBDE0000C || 4 || RW || Set to 1 to start processing
|-
|-
| 0xBD900024 || 4 || W? || Unknown
| 0xBDE00010 || 4 || RW || KIRK command
|-
 
| 0xBD900028 || 4 || W? || Unknown
0x01 = Private decrypt
|-
 
| 0xBD90002C || 4 || W? || Unknown, set to 0
0x02 = Encrypt (type2)
|-
| 0xBD900030 || 4 || W? || Unknown, set to 0
|-
| 0xBD900034 || 4 || RW || Unknown
|-
| 0xBD900038 || 4 || W? || Unknown
|-
| 0xBD900040 || 4 || W? || Unknown
|-
| 0xBD900044 || 4 || RW || Clear/read interrupt flag
|-
|}


= 0xBDA00000: EFlash ATA (PSP Go only) =
0x03 = Decrypt (type2)


Same interface as 0xBD700000.
0x04 = Encrypt (type3) (IV = 0)


= 0xBDB00000: EFlash DMA =
0x05 = Encrypt (type3) (IV = Fuse)


{| class="wikitable"
0x06 = Encrypt (type3) (IV = User)
|-
! Address
! Size
! Read/write
! Description
|-
| 0xBDB00008 || 4 || W? || Set to 1 to reset
|-
| 0xBDB00010 || 4 || W? || Control


Bit 0 = enable
0x07 = Decrypt (type3) (IV = 0)


Bit 1 = 1 if read from ATA, 0 if write to ATA
0x08 = Decrypt (type3) (IV = Fuse)
|-
| 0xBDB00020 || 4 || R? || Read interrupt flag
|-
| 0xBDB00024 || 4 || W? || Clear interrupt flag
|-
| 0xBDB00028 || 4 || RW || Unknown
|-
| 0xBDB0002C || 4 || W? || Unknown, clear bits from the previous register
|-
| 0xBDB00030 || 4 || W? || DMA address
|-
| 0xBDB00034 || 4 || W? || DMA size
|-
| 0xBDB00040 || 4 || W? || Unknown
|-
| 0xBDB00044 || 4 || W? || Unknown, set to 0
|}


= 0xBDE00000: KIRK =
0x09 = Decrypt (type3) (IV = User)


{| class="wikitable"
0x0A = Private Signature Check
|-
! Address
! Size
! Read/write
! Description
|-
| 0xBDE00000 || 4 || R || KIRK signature 'KIRK' (or 1?)
|-
| 0xBDE00004 || 4 || R || KIRK version '0010' (or 1?)
|-
| 0xBDE00008 || 4 || RW || Set to 1 on error by the command subroutine
|-
| 0xBDE0000C || 4 || RW || Set to 1 to start processing, or 2 to start processing phase2
|-
| 0xBDE00010 || 4 || RW || KIRK command


0x01 = Private decrypt
0x0B = SHA-1 Hash


0x02 = Encrypt (type2)
0x0C = ECDSA Key Generate


0x03 = Decrypt (type2)
0x0D = ECDSA Point Multiply


0x04 = Encrypt (type3) (IV = 0)
0x0E = Pseudo-random Number Generator


0x05 = Encrypt (type3) (IV = Fuse)
0x0F = PRNG Seed? Init?


0x06 = Encrypt (type3) (IV = User)
0x10 = ECDSA Sign


0x07 = Decrypt (type3) (IV = 0)
0x11 = ECDSA Signature Check
 
0x08 = Decrypt (type3) (IV = Fuse)
 
0x09 = Decrypt (type3) (IV = User)
 
0x0A = Private Signature Check
 
0x0B = SHA-1 Hash
 
0x0C = ECDSA Key Generate
 
0x0D = ECDSA Point Multiply
 
0x0E = Pseudo-random Number Generator
 
0x0F = PRNG Seed? Init?
 
0x10 = ECDSA Sign
 
0x11 = ECDSA Signature Check
|-
|-
| 0xBDE00014 || 4 || RW || Result of the command
| 0xBDE00014 || 4 || RW || Result of the command
Line 1,760: Line 1,656:
Bit1 and bit5 are not well known, but it seems that bit1 is Error for Phase 1, and Success for Phase 2? Bit5 is only checked for Phase 1, and leads to the same error codepath as bit1.
Bit1 and bit5 are not well known, but it seems that bit1 is Error for Phase 1, and Success for Phase 2? Bit5 is only checked for Phase 1, and leads to the same error codepath as bit1.
|-
|-
| 0xBDE00020 || 4 || RW || Status async?
| 0xBDE00020 || 4 || RW || Unknown
|-
|-
| 0xBDE00024 || 4 || RW || Status async end?
| 0xBDE00024 || 4 || RW || Unknown
|-
|-
| 0xBDE00028 || 4 || RW || Set to the value of 0xBDE0001C at the end of the command subroutine
| 0xBDE00028 || 4 || RW || Set to the value of 0xBDE0001C at the end of the command subroutine
Line 1,776: Line 1,672:
|}
|}


= 0xBDF00000: UMD =
= 0xBDF00000: UMD? =
 
= 0xBE000000: Audio =


{| class="wikitable"
{| class="wikitable"
|-
|-
! Address !! Size !! R/W !! Description
! Address
! Size
! Read/write
! Description
|-
|-
| 0xBC900008 || 4 || RW || Reset
| 0xBE000000 || 4 || W? || Audio init/reset?
 
Bit 0 = reset
|-
|-
| 0xBC900010 || 4 || RW || Set command
| 0xBE000004 || 4 || W? || Enable audio input/output?


Value 0x01 = ?
Bit 0: enable output


Value 0x02 = ?
Bit 1: enable SRC output (?)


Value 0x03 = ?
Bit 2: enable audio input


Value 0x04 = write QTGP2 () at the first transfer address
Bit 3: ??
 
Value 0x05 = write QTGP3 () at the first transfer address
 
Value 0x08 = find region
 
Value 0x09 = ?
 
Value 0x0A = read data
 
Value 0x0B = ?
|-
|-
| 0xBD900014 || 4 || R? || Unknown
| 0xBE000008 || 4 || W? || Same as 0xBE000004 but with reversed bits; maybe stop/empty buffer?
|-
|-
| 0xBD900018 || 4 || R? || Unknown flags
| 0xBE00000C || 4 || R? || Seems to contain the current value for 0xBE000004 (ie the current enabled input/outputs)
|-
|-
| 0xBD90001C || 4 || R? || Unknown
| 0xBE000010 || 4 || W? || Similar to 0xBE000004 but set only when starting playing something, and input bit is set only for loopback test?
|-
|-
| 0xBD900020 || 4 || R? || Get interrupt flags?
| 0xBE000014 || 4 || W? || Unknown, set to 0x1208 = 4616 during initialization
|-
|-
| 0xBD900024 || 4 || RW || Clear interrupt?
| 0xBE000018 || 4 || W? || Unknown, set to 0 during initialization
|-
|-
| 0xBD900028 || 4 || RW || Enable interrupt?
| 0xBE00001C || 4 || R? || Similar to 0xBE000004; possibly bits which finished execution?
|-
|-
| 0xBD90002C || 4 || RW || Disable interrupt?
| 0xBE000020 || 4 || W? || Another similar set of flags
|-
|-
| 0xBD900030 || 4 || RW || Unknown, set to 4
| 0xBE000024 || 4 || W? || Another similar set of flags
|-
|-
| 0xBD900038 || 4 || RW || Unknown, set to 4
| 0xBE000028 || 4 || W? || Another similar set of flags
|-
|-
| 0xBD900040 || 4 || W? || Transfer address 0
| 0xBE00002C || 4 || W? || Another similar set of flags
|-
|-
| 0xBD900044 || 4 || W? || Transfer size 0
| 0xBE000038 || 4 || W? || Set to 256 when frequency in 48kHz, 128 when it is 44.1kHz or during SRC output
|-
|-
| 0xBD900048 || 4 || W? || Transfer address 1
| 0xBE00003C || 4 || W? || Same as above, but not set at initialization time
|-
|-
| 0xBD90004C || 4 || W? || Transfer size 1
| 0xBE000040 || 4 || RW || Frequency-related??
|-
|-
| 0xBD900050 || 4 || W? || Transfer address 2
| 0xBE000044 || 4 || W? || Frequency-related??
|-
|-
| 0xBD900054 || 4 || W? || Transfer size 2
| 0xBE000050 || 4 || RW || Volume?
|-
|-
| 0xBD900058 || 4 || W? || Transfer address 3
| 0xBE000060 || 4 || ? || ??
|-
|-
| 0xBD90005C || 4 || W? || Transfer size 3
| 0xBE000070 || 4 || ? || ??
|-
|-
| 0xBD900060 || 4 || W? || Transfer address 4
| 0xBE000080 || 4 || ? || ??
|-
|-
| 0xBD900064 || 4 || W? || Transfer size 4
| 0xBE0000D0 || 4 || ? || ??
|-
|-
| 0xBD900068 || 4 || W? || Transfer address 5
|}
 
= 0xBE100000: MagicGate hardware for memory stick? =
 
= 0xBE140000: LCDC =
 
{| class="wikitable"
|-
|-
| 0xBD90006C || 4 || W? || Transfer size 5
! Address
! Size
! Read/write
! Description
|-
|-
| 0xBD900070 || 4 || W? || Transfer address 6
| 0xBE140000 || 4 || RW || First LCDC controller enable
 
Bits 0-1 = 3 to enable first LCDC controller (tachyon version < 0x800000; otherwise it's set to 0)
|-
|-
| 0xBD900074 || 4 || W? || Transfer size 6
| 0xBE140004 || 4 || RW || Synchronization difference: (xsync / zoom) - ysync
|-
|-
| 0xBD900078 || 4 || W? || Transfer address 7
| 0xBE140008 || 4 || RW || Unknown (fourth argument of sceLcdcCheckMode and sceLcdcSetMode)
|-
|-
| 0xBD90007C || 4 || W? || Transfer size 7
| 0xBE140010 || 4 || RW || X back porch
|-
|-
| 0xBD900080 || 4 || W? || Transfer address 8
| 0xBE140014 || 4 || RW || X sync width
|-
|-
| 0xBD900084 || 4 || W? || Transfer size 8
| 0xBE140018 || 4 || RW || X front porch
|-
|-
| 0xBD900088 || 4 || W? || Transfer address 9
| 0xBE14001C || 4 || RW || X resolution
|-
|-
| 0xBD90008C || 4 || W? || Transfer size 9
| 0xBE140020 || 4 || RW || Y back porch
|-
|-
| 0xBD900090 || 4 || RW || Total transfer length
| 0xBE140024 || 4 || RW || Y sync width
|-
|-
| 0xBD900094 || 4 || W? || Unknown, can be 0 or 1
| 0xBE140028 || 4 || RW || Y front porch
|-
|-
|}
| 0xBE14002C || 4 || RW || Y resolution
 
|-
= 0xBE000000: Audio =
| 0xBE140030 || 4 || R || HPC (?), returned by sceLcdcReadHPC()
 
{| class="wikitable"
|-
|-
! Address
| 0xBE140034 || 4 || R || VPC (?), returned by sceLcdcReadVPC()
! Size
! Read/write
! Description
|-
|-
| 0xBE000000 || 4 || RW || Audio init/reset?
| 0xBE140040 || 4 || RW || Y shift (between hardware & software resolution)
|-
|-
| 0xBE000004 || 4 || W? || Disable audio input/output?
| 0xBE140044 || 4 || RW || X shift (between hardware & software resolution)
 
Bit 0: enable output
 
Bit 1: enable SRC output (?)
 
Bit 2: enable audio input
 
Bit 3: ??
|-
|-
| 0xBE000008 || 4 || W? || Same as 0xBE000004 but with reversed bits; enable audio input/output?
| 0xBE140048 || 4 || RW || Scaled X resolution
|-
|-
| 0xBE00000C || 4 || RW || Seems to contain the current value for 0xBE000004 (ie the current enabled input/outputs)
| 0xBE14004C || 4 || RW || Scaled Y resolution (same as the physical Y resolution)
|-
|-
| 0xBE000010 || 4 || W? || Similar to 0xBE000004 but set only when starting playing something, and input bit is set only for loopback test?
| 0xBE140050 || 4 || RW || Unknown, set to 1, maybe used by sceLcdcReadUnderflow (to be verified)
|-
|-
| 0xBE000014 || 4 || W? || Unknown, set to 0x1208 = 4616 during initialization
| 0xBE140070 || 4 || W || Set to 1 when running sceLcdcResume() or sceLcdcInit() on tachyon version >= 0x5000000
|-
|-
| 0xBE000018 || 4 || W? || Unknown, set to 0 during initialization
|}
 
The exact same registers are at 0xBE1401.., these ones being used for tachyon version >= 0x8000000 (PSP Go?). <br>
These registers are only set on tachyo version >= 0x8000000:
 
{| class="wikitable"
|-
|-
| 0xBE00001C || 4 || R? || Similar to 0xBE000004; possibly bits which finished execution?
! Address
! Size
! Read/write
! Description
|-
|-
| 0xBE000020 || 4 || W? || Another similar set of flags
| 0xBE140180 || 4 || RW || Always set to 1 when 0xBE140184 - 0xBE140198 are used
|-
|-
| 0xBE000024 || 4 || W? || Another similar set of flags (enabled interrupts?)
| 0xBE140184 || 4 || RW || Scaled X resolution (read instead of the (real) X resolution above when enabled)
|-
|-
| 0xBE000028 || 4 || RW || Another similar set of flags
| 0xBE140188 || 4 || RW || Y resolution (read instead of the (real) Y resolution above when enabled)
|-
|-
| 0xBE00002C || 4 || W? || Another similar set of flags
| 0xBE14018C || 4 || RW || Unknown (0x580 - 0x678)
|-
|-
| 0xBE000038 || 4 || W? || Set to 256 when frequency in 48kHz, 128 when it is 44.1kHz or during SRC output
| 0xBE140190 || 4 || RW || Unknown (0x4C4 - 0x71C)
|-
|-
| 0xBE00003C || 4 || W? || Same as above, but not set at initialization time
| 0xBE140194 || 4 || RW || Unknown (0xAFC - 0xCEC)
|-
|-
| 0xBE000040 || 4 || RW || Frequency-related??
| 0xBE140198 || 4 || RW || Unknown (0x910 - 0xE38)
|-
|-
| 0xBE000044 || 4 || W? || Hardware frequency?
| 0xBE140200 || 4 || W || Set to 1 on initialization
|-
| 0xBE000050 || 4 || RW || Volume?
|-
|-
| 0xBE000060 || 4 || W? || Send audio data?
|-
| 0xBE000070 || 4 || W? || Send audio data?
|-
| 0xBE000080 || 4 || ? || ??
|-
| 0xBE0000D0 || 4 || ? || ??
|}
|}


= 0xBE100000: MagicGate Type-R =
= 0xBE200000: I2c =
 
= 0xBE240000: GPIO =


{| class="wikitable"
{| class="wikitable"
Line 1,939: Line 1,827:
! Description
! Description
|-
|-
| 0xBE100000 || ? || ? || Unknown
| 0xBE240000 || 4 || RW || Unknown
|-
|-
| 0xBE100010 || ? || ? || ?Key size (in bits)?. ex: 0x100 (hardcoded)
| 0xBE240004 || 4 || R || GPIO read pin (1 bit = 1 pin)
|-
|-
| 0xBE100020 || ? || ? || Unknown
| 0xBE240008 || 4 || W || GPIO set pin (1 bit = 1 pin)
|-
|-
| 0xBE100038 || ? || ? || Hardware version 1
| 0xBE24000C || 4 || W|| GPIO clear pin (1 bit = 1 pin)
|-
| 0xBE100040 || 0x10 || ? || Key
|-
|-
| 0xBE100050 || 8 || ? || Unknown
| 0xBE240010 || 4 || ? || Unknown
|-
|-
| 0xBE100060 || 0x10 || ? || IV
| 0xBE240014 || 4 || ? || Unknown
|-
|-
| 0xBE100080 || ? || ? || Control
| 0xBE240018 || 4 || ? || Unknown
|-
|-
| 0xBE100084 || ? || ? || Status
| 0xBE24001C || 4 || ? || Unknown
|-
|-
| 0xBE100088 || ? || ? || Algorithm
| 0xBE240020 || 4 || ? || Unknown
|-
|-
| 0xBE100090 || ? || ? || Unknown. Value at bit 8 is used.
| 0xBE240030 || 4 || ? || Unknown
|-
|-
| 0xBE100094 || ? || ? || Size
| 0xBE240040 || 4 || ? || Unknown
|-
|-
| 0xBE100098 || ? || ? || Hardware version 2
| 0xBE240048 || 4 || ? || Unknown
|-
|-
| 0xBE1000A0 || ?0x800? || ? || Input buffer
|}
|}


= 0xBE140000: LCDC =
= 0xBE300000: Power management? =
 
= 0xBE400000 & 0xBE500000: UART =
 
The second 'xx' bytes of the addresses can be 0x40, 0x44, 0x48, 0x4C, 0x50, 0x54, 0x58, 0x5C for the different UART ports (1-8, in that order).
 
Note that:
* UART1 = ?
* UART2 = ?
* UART3 = ?
* UART4 = ?
* UART5 = Headphone/remote SIO
* UART6 = Infrared
* UART7 = Syscon
* UART8 = PSP 2k+ display-related


{| class="wikitable"
{| class="wikitable"
Line 1,977: Line 1,876:
! Description
! Description
|-
|-
| 0xBE140000 || 4 || RW || First LCDC controller enable
| 0xBExx0000 || 4 || RW || Read/write FIFO of the UART port
 
Bits 0-7 = data


Bits 0-1 = 3 to enable first LCDC controller (tachyon version < 0x800000; otherwise it's set to 0)
Writing writes a byte to the Tx buffer and advances the write position.
|-
Reading reads a byte from the Rx buffer and advances the read position.
| 0xBE140004 || 4 || RW || Synchronization difference: (xsync / zoom) - ysync
The FIFO is 32(?) bytes long.
|-
| 0xBE140008 || 4 || RW || Unknown (fourth argument of sceLcdcCheckMode and sceLcdcSetMode)
|-
| 0xBE140010 || 4 || RW || X back porch
|-
| 0xBE140014 || 4 || RW || X sync width
|-
| 0xBE140018 || 4 || RW || X front porch
|-
| 0xBE14001C || 4 || RW || X resolution
|-
| 0xBE140020 || 4 || RW || Y back porch
|-
| 0xBE140024 || 4 || RW || Y sync width
|-
| 0xBE140028 || 4 || RW || Y front porch
|-
| 0xBE14002C || 4 || RW || Y resolution
|-
| 0xBE140030 || 4 || R || HPC (?), returned by sceLcdcReadHPC()
|-
| 0xBE140034 || 4 || R || VPC (?), returned by sceLcdcReadVPC()
|-
| 0xBE140040 || 4 || RW || Y shift (between hardware & software resolution)
|-
| 0xBE140044 || 4 || RW || X shift (between hardware & software resolution)
|-
| 0xBE140048 || 4 || RW || Scaled X resolution
|-
| 0xBE14004C || 4 || RW || Scaled Y resolution (same as the physical Y resolution)
|-
| 0xBE140050 || 4 || RW || Unknown, set to 1, maybe used by sceLcdcReadUnderflow (to be verified)
|-
| 0xBE140070 || 4 || W || Set to 1 when running sceLcdcResume() or sceLcdcInit() on tachyon version >= 0x5000000
|-
|}
 
The exact same registers are at 0xBE1401.., these ones being used for tachyon version >= 0x8000000 (PSP Go?). <br>
These registers are only set on tachyo version >= 0x8000000:
 
{| class="wikitable"
|-
! Address
! Size
! Read/write
! Description
|-
| 0xBE140180 || 4 || RW || Always set to 1 when 0xBE140184 - 0xBE140198 are used
|-
| 0xBE140184 || 4 || RW || Scaled X resolution (read instead of the (real) X resolution above when enabled)
|-
| 0xBE140188 || 4 || RW || Y resolution (read instead of the (real) Y resolution above when enabled)
|-
| 0xBE14018C || 4 || RW || Unknown (0x580 - 0x678)
|-
| 0xBE140190 || 4 || RW || Unknown (0x4C4 - 0x71C)
|-
| 0xBE140194 || 4 || RW || Unknown (0xAFC - 0xCEC)
|-
| 0xBE140198 || 4 || RW || Unknown (0x910 - 0xE38)
|-
| 0xBE1401A0 || 4 || RW || Display flags?
|-
| 0xBE1401B0 || 4 || RW || Display clock?
|-
| 0xBE140200 || 4 || W || Set to 1 on initialization
|-
|}
 
= 0xBE200000: I2c =
 
 
{| class="wikitable"
|-
! Address
! Size
! Read/write
! Description
|-
| 0xBE200000 || 4 || R? || Unknown
|-
| 0xBE200004 || 4 || RW || Command
 
Value 0x85 = unknown (used after writing the transmit data)
 
Value 0x8A = receive data
 
Value 0x87 = unknown (used after writing the transmit data)
 
|-
| 0xBE200008 || 4 || RW || Data length
|-
| 0xBE20000C || 4 || R? || Read/write data
|-
| 0xBE200010 || 4 || RW || Unknown
|-
| 0xBE200014 || 4 || RW || Unknown
|-
| 0xBE20001C || 4 || RW || Unknown
|-
| 0xBE200028 || 4 || R? || Clear/read interrupt
|-
| 0xBE20002C || 4 || W? || Unknown
|-
|}
 
= 0xBE240000: GPIO =
 
{| class="wikitable"
|-
! Address
! Size
! Read/write
! Description
|-
| 0xBE240000 || 4 || RW || Is output (?)
|-
| 0xBE240004 || 4 || R || GPIO read pin (1 bit = 1 pin)
|-
| 0xBE240008 || 4 || W || GPIO set pin (1 bit = 1 pin)
|-
| 0xBE24000C || 4 || W|| GPIO clear pin (1 bit = 1 pin)
|-
| 0xBE240010 || 4 || RW || Is edge detection (?)
|-
| 0xBE240014 || 4 || RW || Is falling edge (?)
|-
| 0xBE240018 || 4 || RW || Is rising edge (?)
|-
| 0xBE24001C || 4 || RW || Interrupt enable
|-
| 0xBE240020 || 4 || R? || Interrupt Status
|-
| 0xBE240024 || 4 || W || Acknowledge interrupt
|-
| 0xBE240030 || 4 || RW || Capture port enable
|-
| 0xBD240034 || 4 || RW || Timer capture enable
|-
| 0xBE240040 || 4 || RW || Is input on (?)
|-
| 0xBE240048 || 4 || W? || Unknown
|-
|}
 
= 0xBE300000: Power management? =
 
Seems to be composed of 3 controllers, each of size 0x20.
 
= 0xBE4C0000 & 0xBE500000: UART =
 
[https://developer.arm.com/documentation/ddi0183/f/programmer-s-model/summary-of-registers?lang=en ARM PrimeCell UART PL011]
 
There are two similar UART controllers:
* At 0xBE4C0000: UART4 = ?
* At 0xBE500000: UART3 = Headphone/remote SIO
 
There is also possibly an infrared controller at 0xBE540000.
 
UART port numbers vary depending on documentations.
 
Some documentations seem to argue that there are 8 controllers for 0xBE40 to 0xBE5C, but the syscon interface looks very different so it might not be the case.
 
{| class="wikitable"
|-
! Address
! Size
! Read/write
! Description
|-
| 0xBExx0000 || 4 || RW || Read/write FIFO of the UART port
 
Bits 0-7 = data
 
Writing writes a byte to the Tx buffer and advances the write position.
Reading reads a byte from the Rx buffer and advances the read position.
The FIFO is 32(?) bytes long.
|-
| 0xBExx0004 || 4 || RW || Unknown
|-
| 0xBExx0018 || 4 || RW || Port status
 
Bit 4 = Rx buffer status is empty
 
Bit 5 = Tx buffer status is full
|-
| 0xBExx0024 || 4 || W || Upper bits of baudrate divisor, ie (96000000 / baudrate) >> 6
|-
| 0xBExx0028 || 4 || W || Lower bits of baudrate divisor, ie (96000000 / baudrate) & 0x3f
|-
| 0xBExx002C || 4 || RW || Set bits 5-6 to set the baud rate?
|-
| 0xBExx0030 || 4 || RW || Unknown
|-
| 0xBExx0034 || 4 || RW || Unknown
|-
| 0xBExx0038 || 4 || RW || Unknown
|-
| 0xBExx0044 || 4 || RW || Clear interrupt?
|-
|}
 
= 0xBE580000: Syscon =
[https://developer.arm.com/documentation/ddi0194/h/programmer-s-model/summary-of-primecell-ssp-registers?lang=en ARM PrimeCell Synchronous Serial port PL022]
 
TODO: validate register mappings
 
{| class="wikitable"
|-
! Address
! Size
! Read/write
! Description
|-
| 0xBE580000 || 4 || W? || Unknown (0xCF is written there at initialization time)
|-
| 0xBE580004 || 4 || RW || Flags
 
Bit 1 = start syscon command
 
Bit 2 = reset data index
 
Bit 3 = in progress?
|-
| 0xBE580008 || 4 || RW || Read/write data
 
Bits 0-15: 16-bit data
|-
| 0xBE58000C || 4 || R? || Flags
 
Bit 0 = error
 
Bit 2 = not finished
|-
| 0xBE580014 || 4 || W? || Unknown (0 is written there)
|-
| 0xBE580018 || 4 || R? || Unknown
|-
| 0xBE580020 || 4 || W? || Unknown; clear error status?
|-
| 0xBE580024 || 4 || W? || Unknown (0 is written there)
|-
|}
 
= 0xBE5C0000: LCD controller (Slim) =
 
{| class="wikitable"
|-
! Address
! Size
! Read/write
! Description
|-
| 0xBE5C0000 || 4 || W? || Unknown
|-
| 0xBE5C0004 || 4 || W? || Unknown
|-
| 0xBE5C0008 || 4 || RW? || Unknown
|-
| 0xBE5C000C || 4 || R? || Unknown
|-
| 0xBE5C0010 || 4 || W? || Unknown
|-
| 0xBE5C0014 || 4 || W? || Unknown
|-
|-
| 0xBE5C0024 || 4 || W? || Unknown
| 0xBExx0018 || 4 || RW || Port status
|-
|}


= 0xBE740000: Display =
Bit 4 = Rx buffer status is empty


{| class="wikitable"
Bit 5 = Tx buffer status is full
|-
|-
! Address
| 0xBExx0024 || 4 || W || Upper bits of baudrate divisor, ie (96000000 / baudrate) >> 6
! Size
! Read/write
! Description
|-
|-
| 0xBE740000 || 4 || W? || Unknown
| 0xBExx0028 || 4 || W || Lower bits of baudrate divisor, ie (96000000 / baudrate) & 0x3f
|-
| 0xBE740004 || 4 || RW || Get/set row sync (?)
|-
| 0xBE740008 || 4 || R? || Get sync (?)
|-
| 0xBE74000C || 4 || W? || Unknown
|-
| 0xBE740010 || 4 || W? || Unknown
|-
| 0xBE740014 || 4 || W? || Unknown
|-
| 0xBE740020 || 4 || R? || Unknown
|-
|-
| 0xBE740024 || 4 || W? || Unknown
| 0xBExx002C || 4 || W || Set bits 5-6 to set the baud rate?
|-
|-
|}
|}


= 0xBE780000: Display (Slim) =
= 0xBE600000: ? =
 
{| class="wikitable"
|-
! Address
! Size
! Read/write
! Description
|-
| 0xBE780000 || 4 || ? || Unknown
|-
| 0xBE78001C || 4 || ? || Unknown
|}
 
= 0xBFC00000 & 0xBFD00000 & 0xBFE00000: MIPS Reset Vector and RAM =
 
Note this is not a hardware register *per se*.


At boot time, the PSP [[iplloader]] is mapped to read-only 0xBFC00000 then executed. An additional 4096-byte scratchpad-like RAM is accessible at 0xBFD00000 and used as a temporary space to decrypt the IPL blocks.
= 0xBE700000: Display =
Then, once the CPU is reset (0xBC10004C |= 2), the iplloader is unmapped, and the memory which was then at 0xBFD00000 is now mapped at 0xBFC00000 and execution restarts at 0xBFC00000.


On devkit, bloadp is copied to 0xBFE00000 then executed. IPL blocks are usually copied to 0xBFE01000, decrypted in place then executed.
= 0xBFC00000: MIPS Reset Vector =


= 0xBFF00000: NAND DMA buffer =
= 0xBFF00000: NAND DMA buffer =
Line 2,320: Line 1,923:
= References =
= References =


* [http://daifukkat.su/docs/psptek/ PSPTEK]
* [http://daifukkat.su/docs/psptek/ PSPTEK] (done)
* [https://gigawiz.github.io/yapspd/html_chapters_split/chap8.html yapspd]
* [https://gigawiz.github.io/yapspd/html_chapters_split/chap8.html yapspd] (done)
* [https://github.com/uofw/uofw uOFW]
* [https://github.com/uofw/uofw uOFW] (todo: some more info to grab in some modules)
* [https://github.com/jpcsp/jpcsp Jpcsp]
* [https://github.com/jpcsp/jpcsp Jpcsp] (todo: contains a lot of stuff)
Please note that all contributions to PSP Developer wiki are considered to be released under the GNU Free Documentation License 1.2 (see PSP Developer wiki:Copyrights for details). If you do not want your writing to be edited mercilessly and redistributed at will, then do not submit it here.
You are also promising us that you wrote this yourself, or copied it from a public domain or similar free resource. Do not submit copyrighted work without permission!

To protect the wiki against automated edit spam, we kindly ask you to solve the following hCaptcha:

Cancel Editing help (opens in new window)
Retrieved from "http://www.psdevwiki.com/psp/Hardware_Registers"