Service Connectors: Difference between revisions
Jump to navigation
Jump to search
(→5 Pins) |
|||
| (27 intermediate revisions by 3 users not shown) | |||
| Line 5: | Line 5: | ||
== First Connector (5 Pins) == | == First Connector (5 Pins) == | ||
[[File:I2NazzQ.png]] | |||
[[File:5_Pin_Service_Layout_Proto.jpg]] | |||
== Second Connector (24 Pins) == | |||
[[File:qdw8Nxb.png]] | |||
[[File:24_Pin_Service_Connector_Proto.png]] | |||
[[File:Screenshot 2023-11-24 at 9.38.03 PM.png]] | |||
== Third Connector (24 Pins) (Bluray) == | |||
[[File:24_Pin_Bluray_Service_Connector_Proto.png]] | |||
= Meaning of Pins = | = Meaning of Pins = | ||
* Starts at | * Starts at Leftmost (Indicated by Arrow) | ||
== 5 Pins == | |||
{| class="wikitable sortable" | {| class="wikitable sortable" | ||
|- | |- | ||
! PIN # (24 PIN#) !! Meaning !! Notes | |||
|- | |||
| 1 || Ground || Ground Plane | |||
|- | |||
| 2(7) || Transmit EMC || Used to send commands to EMC. command always <com>:<chk>\r\n | |||
|- | |||
| 3(6) || Receive EMC || Used to recv responses from EMC. response always <res>:<chk>\r\n | |||
|- | |||
| 4(14) || titania uart1 tx || titania uart1 tx (bootrom: 460800, eap fw, apu: 230400) | |||
|- | |||
| 5(13) || titania uart1 rx || titania uart1 rx (bootrom: 460800, eap fw, apu: 230400) | |||
|- | |||
|} | |||
== 24 Pins == | |||
* Major credits to shuffle2 for the complete pinout | |||
{| class="wikitable sortable" | |||
! PIN # !! Meaning !! Notes | ! PIN # !! Meaning !! Notes | ||
|- | |- | ||
| GND || Ground || Ground Plane | | 1 || VDD || 5v | ||
|- | |||
| 2 || VDD || 5v | |||
|- | |||
| 3 || GND || Ground Plane | |||
|- | |||
| 4 || GND || Ground Plane | |||
|- | |||
| 5 || emc gpio a1 || pulling low at emc boot causes emc rom to enter uart shell @ 460800 | |||
|- | |||
| 6 || Receive EMC || Used to recv responses from EMC. response always <res>:<chk>\r\n (uart rx emc 115200) | |||
|- | |||
| 7 || Transmit EMC || Used to send commands to EMC. command always <com>:<chk>\r\n (uart tx emc 115200) | |||
|- | |||
| 8 || 3v3 || goes low when emc resets | |||
|- | |||
| 9 || 0v || 0v | |||
|- | |||
| 10 || GND || Ground Plane | |||
|- | |||
| 11 || titania uart0 tx || titania uart0 tx (efc fw: 460800) | |||
|- | |||
| 12 || titania uart0 rx || titania uart0 rx (efc fw: 460800) | |||
|- | |||
| 13 || titania uart1 rx || titania uart1 rx (bootrom: 460800, eap fw, apu: 230400) | |||
|- | |||
| 14 || titania uart1 tx || titania uart1 tx (bootrom: 460800, eap fw, apu: 230400) | |||
|- | |||
| 15 || GND || Ground Plane | |||
|- | |||
| 16 || emc gpio c5 || ("GPI SW" (only used if devif_det# active)) | |||
|- | |||
| 17 || 0v || 0v | |||
|- | |||
| 18 || 5v || 5v | |||
|- | |||
| 19 || emc gpio a49 || emc gpio a49 | |||
|- | |- | ||
| | | 20 || emc gpio a27 || emc gpio a27. main power switch | ||
|- | |- | ||
| | | 21 || i2c data || i2c data (i2c_bus_4) | ||
|- | |- | ||
| | | 22 || i2c clock || (i2c_bus_4) | ||
|- | |- | ||
| | | 23 || GND || Ground Plane | ||
|- | |- | ||
| 24 || emc reset# || emc reset# | |||
|} | |} | ||
Latest revision as of 23:20, 23 October 2024
There are two Service Connectors on the PS5:
Pictures[edit | edit source]
First Connector (5 Pins)[edit | edit source]
Second Connector (24 Pins)[edit | edit source]
Third Connector (24 Pins) (Bluray)[edit | edit source]
Meaning of Pins[edit | edit source]
- Starts at Leftmost (Indicated by Arrow)
5 Pins[edit | edit source]
| PIN # (24 PIN#) | Meaning | Notes |
|---|---|---|
| 1 | Ground | Ground Plane |
| 2(7) | Transmit EMC | Used to send commands to EMC. command always <com>:<chk>\r\n |
| 3(6) | Receive EMC | Used to recv responses from EMC. response always <res>:<chk>\r\n |
| 4(14) | titania uart1 tx | titania uart1 tx (bootrom: 460800, eap fw, apu: 230400) |
| 5(13) | titania uart1 rx | titania uart1 rx (bootrom: 460800, eap fw, apu: 230400) |
24 Pins[edit | edit source]
- Major credits to shuffle2 for the complete pinout
| PIN # | Meaning | Notes |
|---|---|---|
| 1 | VDD | 5v |
| 2 | VDD | 5v |
| 3 | GND | Ground Plane |
| 4 | GND | Ground Plane |
| 5 | emc gpio a1 | pulling low at emc boot causes emc rom to enter uart shell @ 460800 |
| 6 | Receive EMC | Used to recv responses from EMC. response always <res>:<chk>\r\n (uart rx emc 115200) |
| 7 | Transmit EMC | Used to send commands to EMC. command always <com>:<chk>\r\n (uart tx emc 115200) |
| 8 | 3v3 | goes low when emc resets |
| 9 | 0v | 0v |
| 10 | GND | Ground Plane |
| 11 | titania uart0 tx | titania uart0 tx (efc fw: 460800) |
| 12 | titania uart0 rx | titania uart0 rx (efc fw: 460800) |
| 13 | titania uart1 rx | titania uart1 rx (bootrom: 460800, eap fw, apu: 230400) |
| 14 | titania uart1 tx | titania uart1 tx (bootrom: 460800, eap fw, apu: 230400) |
| 15 | GND | Ground Plane |
| 16 | emc gpio c5 | ("GPI SW" (only used if devif_det# active)) |
| 17 | 0v | 0v |
| 18 | 5v | 5v |
| 19 | emc gpio a49 | emc gpio a49 |
| 20 | emc gpio a27 | emc gpio a27. main power switch |
| 21 | i2c data | i2c data (i2c_bus_4) |
| 22 | i2c clock | (i2c_bus_4) |
| 23 | GND | Ground Plane |
| 24 | emc reset# | emc reset# |