Editing DualSense HID Commands

= Get MCU Unique ID =
Get MediaTek Main MCU Unique ID
<pre>
	ReportID = 128,
	DeviceID = 1,
	ActionID = 9
</pre>

= Read Device Info =

<pre>
	ReportID = 128,
	DeviceID = 1,
	ActionID = 12
</pre>

= Erase Device Info ['''DANGER'''] =

<pre>
	ReportID = 128,
	DeviceID = 1,
	ActionID = 12
</pre>

= Spider DSP Init Get Status =

<pre>
	ReportID = 129,
	DeviceID = 16,
	ActionID = 1
</pre>

= Spider DSP Get Status =

<pre>
	ReportID = 129,
	DeviceID = 16,
	ActionID = 2
</pre>

= Spider DSP Patch Finalize =
<pre>
	ReportID = 128,
	DeviceID = 16,
	ActionID = 5
</pre>

= Spider DSP Finalize Get Status =
<pre>
	ReportID = 129,
	DeviceID = 16,
	ActionID = 5
</pre>

= Spider DSP Firmware Patch =
<pre>
	ReportID = 128,
	DeviceID = 16,
	ActionID = 2,
	DataLen = 57
</pre>

= Spider DSP Firmware Patch Init =

<pre>
	ReportID = 128,
	DeviceID = 16,
	ActionID = 1
</pre>

= Spider DSP Firmware Verify =
<pre>
	ReportID = 128,
	DeviceID = 16,
	ActionID = 3
</pre>

= Spider DSP Firmware Verify Status =
<pre>
	ReportID = 129,
	DeviceID = 16,
	ActionID = 5
</pre>

= Spider DSP Firmware Verify Request =

<pre>
	ReportID = 128,
	DeviceID = 16,
	ActionID = 7
</pre>

= Spider DSP Firmware Verify Request Status =

<pre>
	ReportID = 129,
	DeviceID = 16,
	ActionID = 7
</pre>

= Get TP UID =
Get Touch Panel Ubique ID
<pre>
	ReportID = 128,
	DeviceID = 5,
	ActionID = 2
</pre>

= Get TP Version =
Get Touch Panel Version
<pre>
	ReportID = 128,
	DeviceID = 5,
	ActionID = 4
</pre>

= Get Table ID =

<pre>
	ReportID = 164,
	DeviceID = 3,
	ActionID = 2,
	DataLenLocal = 5
</pre>

= Reset =

<pre>
	ReportID = 128,
	DeviceID = 1,
	ActionID = 1
</pre>

= Request Table ID = 

<pre>
	ReportID = 160,
	DeviceID = 3,
	ActionID = 2
</pre>

= Reboot Secure Boot Loader =

<pre>
	ReportID = 128,
	RebootCmd = 1
</pre>

= Read Patch Info =

<pre>
	ReportID = 128,
	DeviceID = 9,
	ActionID = 13
</pre>

= Get Firmware Info =

<pre>
    ReportID = 32
</pre>

= Start Gyroscope Offset =

<pre>
	ReportID = 144,
	ActionID = 1,
	DeviceID = 2,
	TargetID = 7
</pre>

= Get Gyroscope Offset State =

<pre>
	ReportID = 145,
	DeviceID = 2,
	TargetID = 7
</pre>

= Get BlueTooth Patch Data =

<pre>
	ReportID = 129,
	DeviceID = 14,
	ActionID = 3
</pre>

= Get BlueTooth Patch Info =

<pre>
	ReportID = 129,
	DeviceID = 9,
	ActionID = 13
</pre>

= Get Audio Codec State =

<pre>
	ReportID = 164,
	DeviceID = 16,
	ActionID = 1
</pre>

= Flash =

<pre>
	ReportID = 240,
	DownloadCmd = 0,
	DataLen = 57,
	WriteCmd = 1
</pre>

= Audio Codec Select =

<pre>
	ReportID = 160,
	DeviceID = 16,
	ActionID = 1
</pre>

= Blue Tooth Patch =

<pre>
	ReportID = 128,
	DeviceID = 14,
	ActionID = 2,
	DataLen = 57
</pre>

= Read Blue Tooth Patch =

<pre>
	ReportID = 128,
	DeviceID = 14,
	ActionID = 4
</pre>

= Read Blue Tooth Patch Info =

<pre>
	ReportID = 129,
	DeviceID = 14,
	ActionID = 4
</pre>

= Blue Tooth Patch Finalize =

<pre>
	ReportID = 128,
	DeviceID = 14,
	ActionID = 5
</pre>

= Blue Tooth Patch Init =

<pre>
	ReportID = 128,
	DeviceID = 14,
	ActionID = 1
</pre>

= Blue Tooth Patch Restart =

<pre>
	ReportID = 128,
	DeviceID = 14,
	ActionID = 6
</pre>

= Blue Tooth Patch Verify =

<pre>
	ReportID = 128,
	DeviceID = 14,
	ActionID = 3
</pre>

= Blue Tooth Restart Result =

<pre>
	ReportID = 129,
	DeviceID = 14,
	ActionID = 6
</pre>

= Get BT Address =
<pre>
	ReportID = 129,
	DeviceID = 9,
	ActionID = 2,
	DataLen = 6
</pre>

= Set BT Address =

<pre>
    ReportID = 128,
	DeviceID = 9,
	ActionID = 1,
	ReadCmd = 2,
	DataLen = 6
</pre>

= Set BlueTooth Disable Enable =

<pre>
	ReportID = 128,
	DeviceID = 9,
	ActionID = 5,
	Param = 0
</pre>

= Set BlueTooth Enable =

<pre>
    ReportID = 128,
	DeviceID = 9,
	ActionID = 5,
	Param = 1
</pre>

= Set BlueTooth Table =

<pre>
    ReportID = 165,
	PowerTable = 1,
	RadioTable = 2,
	DataLen = 16,
	DataBegin = 0,
	PowerTableSize = 224,
	RadioTableSize = 112,
	DataMaxLen = (max value of a byte, 255)
	DataMinLen = 0
</pre>

= Set DFU Mode  =
'''Note 1''': This command does not work with retail controllers 'tested with many controllers' but it may work with DVT/Prototype controllers.
'''Note 2''': The mainboard immediately boot into PBL (Primary Boot Loader) mode on the factory before flashing Main "Banana" firmware, then it will be disabled after that. 
<pre>
    ReportID = 160,
	DisableMode = 0,
	EnablePBLMode = 1,
	EnableSBLMode = 2,
	EnableMode = 1
</pre>

= Set Hardware Version =

<pre>
    ReportID = 128,
	DeviceID = 1,
	ActionID = 5
</pre>

= Write PCBAID =

<pre>
ReportID = 128,
	DeviceID = 1,
	ActionID = 3,
	DataLen = 6
</pre>

= Read PCBAID =

<pre>
ReportID = 128,
	DeviceID = 1,
	ActionID = 4,
</pre>

= Set Power Charge Off =

<pre>
	ReportID = 128,
	DeviceID = 2,
	ActionID = 3,
	Param0 = 208,
	Param1 = 38,
	Param2 = 117,
	Param3 = 192
</pre>

= Set Power Charge On =

<pre>
	ReportID = 128,
	DeviceID = 2,
	ActionID = 2,
	Param0 = 208,
	Param1 = 38,
	Param2 = 117,
	Param3 = 192
</pre>

= Get Read OTP  =

<pre>
	ReportID = 164,
	DeviceID = 3,
	ActionID = 9
</pre>

= Set Read OTP  =

<pre>
ReportID = 160,
	DeviceID = 3,
	ActionID = 9,
	Offset = 23,
	Length = 1
</pre>

= Set Secure Boot Loader  =

<pre>
ReportID = 160,
	SetCmd = 2
</pre>

= Set VDD External Power Off =

<pre>
ReportID = 160,
	DeviceID = 17,
	ActionID = 1,
	Param = 0
</pre>

= Set VDD External Power On =

<pre>
ReportID = 160,
	DeviceID = 17,
	ActionID = 1,
	Param = 1
</pre>

= Venom Get Status =

<pre>
	ReportID = 129,
	DeviceID = 15,
	ActionID = 2
</pre>

= Set Venom FW Version =

<pre>
ReportID = 128,
	DeviceID = 6,
	ActionID = 3
</pre>

= Venom Finalize Get Status =

<pre>
	ReportID = 129,
	DeviceID = 15,
	ActionID = 5
</pre>

= Venom Firmware Patch =

<pre>
	ReportID = 128,
	DeviceID = 15,
	ActionID = 2,
	DataLen = 57
</pre>

= Venom Firmware Patch Init =

<pre>
	ReportID = 128,
	DeviceID = 15,
	ActionID = 1
</pre>

= Venom Firmware Verify =

<pre>
	ReportID = 128,
	DeviceID = 15,
	ActionID = 3
</pre>

= Venom Firmware Verify Request =

<pre>
	ReportID = 128,
	DeviceID = 15,
	ActionID = 7
</pre>

= Venom Firmware Verify Request Status =

<pre>
	ReportID = 129,
	DeviceID = 15,
	ActionID = 7
</pre>

= Venom Firmware Verify Status =

<pre>
	ReportID = 129,
	DeviceID = 15,
	ActionID = 5
</pre>

= Venom Init Get Status =

<pre>
	ReportID = 129,
	DeviceID = 15,
	ActionID = 1
</pre>

= Venom Patch Finalize =

<pre>
	ReportID = 128,
	DeviceID = 15,
	ActionID = 5
</pre>

= Set bonding =

<pre>
	ReportID = 128,
	DeviceID = 1,
	ActionID = 14
</pre>

= NVS Unlock =

<pre>
  ReportID = 128, 
  DeviceID = 3,
  ActionID = 2,
  Param0 = 101,
  Param1 = 50,
  Param2 = 64,
  Param3 = 12
</pre>