Editing Talk:DualShock 4
Jump to navigation
Jump to search
The edit can be undone. Please check the comparison below to verify that this is what you want to do, and then publish the changes below to finish undoing the edit.
| Latest revision | Your text | ||
| Line 20: | Line 20: | ||
== Hardware == | == Hardware == | ||
Teardown photo album | Teardown photo album: http://imgur.com/a/ytRW5 | ||
The USB port and LED are on one separate board, connected using a [http://en.wikipedia.org/wiki/Flexible_flat_cable flat flexible cable], this cable is connected to a vertical FFC connector that does not have a locking mechanism. | The USB port and LED are on one separate board, connected using a [http://en.wikipedia.org/wiki/Flexible_flat_cable flat flexible cable], this cable is connected to a vertical FFC connector that does not have a locking mechanism. | ||
'''Main microcontroller:''' is a Spansion MB9BF002, a ARM Cortex M3 core, | '''Main microcontroller:''' is a Spansion MB9BF002, a ARM Cortex M3 core, BGA package. The reset and SWD signals might be exposed to test points, I am not sure. | ||
'''Power Management IC (PMIC):''' There's a | '''Power Management IC (PMIC):''' There's a chip marked with "BD9200" (in QFN 32 pin footprint), it has some thick traces around it, plus a big inductor. One of the pins near it read 6V, might be for the motor. | ||
'''Bluetooth module:''' shows "8LA18366" and "GS-WCM-01" and "VR2.0". There is also a | '''Bluetooth module:''' shows "8LA18366" and "GS-WCM-01" (or maybe it's "GS-WCN-01") and "VR2.0". There is also a QR code that I can't decipher yet. There are a lot of test points near it. Underneath, it is confirmed to be a Qualcomm Atheros AR3002. | ||
'''Six-axis sensor:''' There's a rectangular | '''Six-axis sensor:''' There's a rectangular (maybe LGA) chip on the bottom side on the left, marked with "134" "A1322" "333": [http://www.bosch-sensortec.com/en/homepage/products_3/6_axis_sensors_2/inertial_measurement_unit_1/bmi055_1/bmi055 Bosch-sensortec GMBH BMI055] inertial sensor used for the three-axis gyroscope and three-axis accelerometer. It's got some sort of latch signal around it, or maybe it's a weird clock. It's slow and doesn't seem like a bus. Or it could be a shift register and it's reading blank because I'm not pressing buttons. | ||
'''Touchpad sensor:''' (with Atmel 8-bit AVR Microcontroller ATiny2313) is also detachable, connected using a flat flexible cable, this cable is connected to the main PCB using a connector that has a flip-up locking mechanism. | '''Touchpad sensor:''' (with Atmel 8-bit AVR Microcontroller ATiny2313) is also detachable, connected using a flat flexible cable, this cable is connected to the main PCB using a connector that has a flip-up locking mechanism. | ||
'''Speaker:''' (EAS1S181F) is | '''Speaker:''' (EAS1S181F) is built-in and it connects to the main PCB using some raised contacts. | ||
'''Audio codecs:''' There's a {{G|QFN}} 32 pin chip marked with "WM1801G" (Wolfson Microelectronics) "36A0LM6" dead center on the bottom side of the PCB. It is near the audio stuff but it is also near where all the buttons connect. There are 5 test points near it. It appears to be communicating with {{G|SPI BUS}} with constant activity. There's also two resistors that look like {{G|I²C}} pull-up resistors, and there appears to be constant I2C traffic. | '''Audio codecs:''' There's a {{G|QFN}} 32 pin chip marked with "[[:File:WM1801G.jpg|WM1801G]]" (Wolfson Microelectronics) "36A0LM6" dead center on the bottom side of the PCB. It is near the audio stuff but it is also near where all the buttons connect. There are 5 test points near it. It appears to be communicating with {{G|SPI BUS}} with constant activity. There's also two resistors that look like {{G|I²C}} pull-up resistors, and there appears to be constant I2C traffic. | ||
There's a shiny small square chip left of the left analog stick, it is marked with "7710" "325A1", I have no idea what this is, but there's some differential signals coming out of it, it might be USB, the activity stops when I disconnect the USB cable. I think this is connected to the USB port. I suspect this is a OTG chip. | There's a shiny small square chip left of the left analog stick, it is marked with "7710" "325A1", I have no idea what this is, but there's some differential signals coming out of it, it might be USB, the activity stops when I disconnect the USB cable. I think this is connected to the USB port. I suspect this is a OTG chip. | ||
| Line 142: | Line 42: | ||
Some buttons are active low, some are active high (maybe only the thumbstick push buttons). The sheet of flexible circuit for the buttons are active low. | Some buttons are active low, some are active high (maybe only the thumbstick push buttons). The sheet of flexible circuit for the buttons are active low. | ||
I'll keep adding to this section | |||
=== Flexible Film Pin Mapping === | === Flexible Film Pin Mapping === | ||
| Line 160: | Line 51: | ||
See main page (skewed button connector) for pins purpose. | See main page (skewed button connector) for pins purpose. | ||