Editing JAISPI

{{Wikify}}

Someone should crosscheck the spanish and realworld into english for wiki here, please.

== JAISPI ==
JAISPI - Raspberry Pi SPI flasher for PS4

Source: 
* http://jaicrab.org/?&a=Raspberry/Article/JAISPI
* http://jaicrab.org/?&a=Ps4/Tools/JAISPI

JAISPI - Utility to read and write to the main memory ([[MX25L25635FMI-10G]]) of PS4 with the Raspberry Pi through the SPI protocol.

=== Changelog ===
* v1.0
** Support [[MX25L25635FMI-10G]]
** Reading
** Programming
** Full Erase

=== Installation Instructions ===

==== Materials Required ====
* 1x [[Raspberry Pi]] (see [[Raspberry_Pi#Where_to_buy.3F|here for where to buy]])
* 1x SD Memory (for Raspbian, a 4GB minimal is recommended)
* 1x PS4 Serial Flash [[MX25L25635FMI-10G]] desoldered from console

==== Downloads ====
* Raspbian (http://downloads.raspberrypi.org/raspbian_latest)
* Win32 Disk Imager (http://sourceforge.net/projects/win32diskimager/files/latest/download)
* Putty (http://the.earth.li/~sgtatham/putty/latest/x86/putty.exe)

=== Pinout ===

<div style="float:right">[[File:MX25L1006E Pinout.png|200px|thumb|left|[[MX25L1006E]] Pinout]]<br />[[File:25X10CLYA1 Pinout.png|200px|thumb|left|[[25X10CLYA1]] Pinout]]<br />[[File:MX25L25635FMI-10G Pinout.png|200px|thumb|left|[[MX25L25635FMI-10G]] Pinout]]<br />
[[File:Raspberry-pi-rev-1-gpio-pin-out1.jpg|200px|thumb|left|Raspberry Pi GPIO pinout]]<br />[[File:Raspberry Pi - model B plus - gpio.png|200px|thumb|left|Raspberry Pi model B+ GPIO pinout]]</div>
{| border="1" cellspacing="0" cellpadding="5" border="#999" class="wikitable" style="border:1px solid #999; border-collapse: collapse;" 
|- bgcolor="#cccccc"
! 8-Pin !! 16-pin !! Usage !! Raspberry Pi<br />JAISPI || Description
|-
| - || 1 || SIO3 || style="color:white; background-color:darkgrey;" | NC || 8pin: Not Available - not used / 16pin: Serial Data Input & Output (for 4xI/O read mode)
|-
| 8 || 2 || VCC || 17 || +3V DC Power Supply
|-
| 7 || 3 || HOLD#/RESET# || style="color:white; background-color:darkgrey;" | NC || 8pin: Hold, to pause the device without deselecting the device / 16pin: Hardware Reset Pin Active low
|-
| - || 4 || style="color:white; background-color:darkgrey;" | NC || style="color:white; background-color:darkgrey;" | NC || style="color:white; background-color:darkgrey;" | No Connection 
|-
| - || 5 || style="color:white; background-color:darkgrey;" | NC || style="color:white; background-color:darkgrey;" | NC || style="color:white; background-color:darkgrey;" | No Connection 
|-
| - || 6 || style="color:white; background-color:darkgrey;" | NC || style="color:white; background-color:darkgrey;" | NC || style="color:white; background-color:darkgrey;" | No Connection 
|-
| 1 || 7 || CS# || 24 || Chip Select
|-
| 2 || 8 || SO/SIO1 || 21 || Serial Data Output (for 1 x I/O) or Serial Data Input & Output (for 2x I/O or 4x I/O read mode)
|-
| 3 || 9 || WP#/SIO2 || 25 || Write Protection: connect to GND or Serial Data Input & Output (for 4x I/O read mode)
|-
| 4 || 10 || GND || 25 || Ground
|-
| - || 11 || style="color:white; background-color:darkgrey;" | NC || style="color:white; background-color:darkgrey;" | NC || style="color:white; background-color:darkgrey;" | No Connection 
|-
| - || 12 || style="color:white; background-color:darkgrey;" | NC || style="color:white; background-color:darkgrey;" | NC || style="color:white; background-color:darkgrey;" | No Connection 
|-
| - || 13 || style="color:white; background-color:darkgrey;" | NC || style="color:white; background-color:darkgrey;" | NC || style="color:white; background-color:darkgrey;" | No Connection 
|-
| - || 14 || style="color:white; background-color:darkgrey;" | NC || style="color:white; background-color:darkgrey;" | NC || style="color:white; background-color:darkgrey;" | No Connection 
|-
| 5 || 15 || SI/SIO0 || 19 || Serial Data Input (for 1 x I/O) or Serial Data Input & Output (for 2x I/O or 4x I/O read mode)
|-
| 6 || 16 || SCLK || 23 || Clock Input
|-
|}

Use short wires, esp. if you are not adding the 0.1{{micro}}F capacitor between ground and vcc as close as possible to the chip

[http://www.raspberrypi.org/introducing-raspberry-pi-model-b-plus/ newer Raspberry Pi model B+] and Raspberry Pi model A+ both use same pinout for the first 26 pinheaders as the previous nonplus model, so it should work on that as well.


=== Installation ===

==== Installing Raspbian ====
Run win32diskimage (if you use linux you can use dd)<br />
[[File:Win32DiskImager.png]]
# In "Image file" select the downloaded and decompressed Raspbian image (''2013-09-25-wheezy-raspbian.img'' at the time of this writing)
# In "Device" select the drive where the SD memory is.
# Select "Write".
After finished writing, put the SD card in the Raspberry Pi and power it up by inserting the USB cable.

==== Remote Shell into Raspbian ====
Two minutes after booting up the Raspberry Pi, run Putty.<br />
[[File:Putty.png]]
# In Host Name put: raspberrypi<br />If this doesn't works properly, go to the router, find the IP assigned to your Raspberry Pi and use that instead,
# Select SSH
# Select Open

==== Installing Application ====
It will request a Login. According Raspbian the user is "pi" and the password "raspberry" (Both without quotes).

Insert the following commands:
{{keyboard|content=
sudo -s
cd /bin
wget http://jaicrab.org/Ps4/Tools/JAISPI/jaispi
chmod +x jaispi
echo "#blacklist spi-bcm2708" > /etc/modprobe.d/raspi-blacklist.conf
echo "blacklist i2c-bcm2708" >> /etc/modprobe.d/raspi-blacklist.conf
reboot
}}

Installation is complete. By Putty you can access the Raspberry Pi. To run the command jaispi you need to be root (sudo-s):
{{keyboard|content=
# sudo -s
# Jaispi -i / dev/spidev0.0
}}

=== Options ===
  -i /dev/spidevX.X             Get ID from flash
  -r file.bin /dev/spidevX.X    Read entire flash to file
  -e /dev/spidevX.X             Erase entire flash
  -p file.bin /dev/spidevX.X    Only write blocks differences from file
  -v file.bin /dev/spidevX.X    Verify blocks with file
==== Get ID ====
-i: Displays information of the flash.
 #jaispi -i /dev/spidev0.0
 JaiSpi v1.0
 ID:  0xC22019 MX25L25635
==== Read ====
-r: Makes a full dump of the flash (Average time: 35sec)
 #jaispi -r DUMP.bin /dev/spidev0.0
 JaiSpi v1.0
 ID:  0xC22019 MX25L25635
 Reading...
 0x02000000
 Done!
==== Erase ====
-e: Clears all flash (Average time: 1min, 30sec)
 #jaispi -e /dev/spidev0.0
 JaiSpi v1.0
 ID:  0xC22019 MX25L25635
 Erasing blocks...
 Done!
==== Program ====
-p: Write to flash only the changed sectors (Average time: 1min 30sec)
 #jaispi -p Base.bin /dev/spidev0.0
 JaiSpi v1.0
 ID:  0xC22019 MX25L25635
 Starting...
 0x02000000 -> 8192 Sectors written
 Done!
==== Verify ====
-v: Compares the flash contents with a file in PC (Average time: 35sec)
 #jaispi -v Base.bin /dev/spidev0.0
 JaiSpi v1.0
 ID:  0xC22019 MX25L25635
 Checking...
 0x02000000 -> 0 Different sectors
 Done!

=== JAISPI / PS4 NOR Chip Dumping personal experience by AlphaHacks ===

PS4 NOR Chip Dumping Process Documentation
* [https://www.mediafire.com/?6jcpwd7mzw6fnsk as PDF]
* [http://playstationhax.it/forums/topic/1749-ps4-nor-chip-dumping-process-documentation/ as forumtopic]


{{Hardware Modification}}
<noinclude>[[Category:Main]]</noinclude>