PCI

PCI pads - as seen on COK-002
note: Two circular pads in the bottom right corner are for southbridge serial

Communication Processor (PCI) connector beneath the PCIe x4 connector on a TMU-520

PCI

Bus, resembling Conventional PCI 2.3, directly connected to South Bridge, with 80 exposed pads

Activated by setting offset 0x48C02 in SC EEPROM to 0x00 or 0x03:

• 0x00 is for IFB (InterFace Board, used by CEB)
• 0x03 is for Communication Processor (PIF5, used by DEH-R10XX and DECR-1000)
  • Does also have support for all retail platforms (e.g. COK-001, VER-001 or RTX-001)

Supported devices:

Device ID	Device "Name"	Firmware
104D8183	Sony IFB ATHENS Board Revision 0x1	010.??? to Template:Latest
104D81FF	Sony PIF5 TMR Board Revision 0x101	060.004 to Template:Latest
104D8200	Sony DVE (RSX Tracing) FPGA	082.006 to Template:Latest
104D820E	Sony CXD9208GP PS2 emulation subsystem adapter	082.006 to Template:Latest
80861076	Intel 82541PI Gigabit Ethernet Controller	010.??? to Template:Latest

Major differences from PCI standard:

• smaller formfactor (80 pin, instead of miniPCI 100P-type I/II or MiniPCI 124P-Type III)
• no use of miniPCI standard sideband signals for audio and communications
• no support of the miniPCI standard CLKRUN# signal defined in the PCI Mobile Design Guide
• no support for optional JTAG signals, nor for the 64-bit PCI extension defined in the PCI Local Bus Specification

70/80 pin miniPCI pad layout

CN3208 80P on CECHAxx/CECHBxx COK-001, CECHCxx/CECHExx COK-002(W), CECH-20xx DYN-001 and all later models

CN3208 70P on CECHGxx SEM-001, CECHHxx DIA-001, CECHJxx/CECHKxx DIA-002 and CECHLxx/CECHMxx/CECHPxx/CECHQxx VER-001

80P Pin	70P Pin	Usage	100P Pin (Type I/II)	124P Pin (Type III)	Remark
01	35	+3.3V_PCI	03, 08, 12, 15, 24, 47, 54, 72, 73	19, 24, 28, 31, 40, 63, 70, 88, 89 (not 124)	VCC
02	70	GND	7, 11, 16, 21, 33, 34, 39, 46, 53, 58, 61, 66, 67, 85, 86, 98	23, 27, 32, 37, 49, 50, 55, 62, 69, 74, 77, 82, 83, 101, 102, 114	Ground
03	-	PIO15			?
04	-	PIO11			?
05	-	PIO14			?
06	-	PIO10			?
07	-	PIO13			?
08	-	PIO9			?
09	-	PIO12			?
10	-	PIO8			?
11	01	GND	07, 11, 16, 21, 33, 34, 39, 46, 53, 58, 61, 66, 67, 85, 86, 98	23, 27, 32, 37, 49, 50, 55, 62, 69, 74, 77, 82, 83, 101, 102, 114	Ground
12	36	GND	07, 11, 16, 21, 33, 34, 39, 46, 53, 58, 61, 66, 67, 85, 86, 98	23, 27, 32, 37, 49, 50, 55, 62, 69, 74, 77, 82, 83, 101, 102, 114	Ground
13	02	/INTA	04	20	Interrupt line A (open-drain)
14	37	/INTB	01	17	Interrupt line B (open-drain)
15	03	/INTC	-	-	Interrupt line C (open-drain)
16	38	/INTD	-	-	Interrupt line D (open-drain)
17	04	/RST	10	26	Reset
18	39	GND	07, 11, 16, 21, 33, 34, 39, 46, 53, 58, 61, 66, 67, 85, 86, 98	23, 27, 32, 37, 49, 50, 55, 62, 69, 74, 77, 82, 83, 101, 102, 114	Ground
19	05	/GNT	14	30	Bus grant from motherboard to card
20	40	CLK	09	25
21	06	GND	07, 11, 16, 21, 33, 34, 39, 46, 53, 58, 61, 66, 67, 85, 86, 98	23, 27, 32, 37, 49, 50, 55, 62, 69, 74, 77, 82, 83, 101, 102, 114	Ground
22	41	GND	07, 11, 16, 21, 33, 34, 39, 46, 53, 58, 61, 66, 67, 85, 86, 98	23, 27, 32, 37, 49, 50, 55, 62, 69, 74, 77, 82, 83, 101, 102, 114	Ground
23	07	/PME	18	34	Power management event. 3.3 V, open drain, active low
24	42	/REQ			Bus request from card to motherboard
25	08	AD30	22	38	Address/Data 30
26	43	AD31	17	33	Address/Data 31
27	09	AD28	26	42	Address/Data 28
28	44	AD29	19	35	Address/Data 29
29	10	AD26	28	44	Address/Data 26
30	45	AD27	23	39	Address/Data 27
31	11	AD24	30	46	Address/Data 24
32	46	AD25	25	41	Address/Data 25
33	12	IDSEL			IDSEL is asserted by PCI system to select the connected device during configuration read and write transactions.
34	47	/C/BE3			Command/Byte Enable 3 // These inputs are the multiplexed Bus Command and Byte Enable signals on the PCI bus.
35	13	GND	07, 11, 16, 21, 33, 34, 39, 46, 53, 58, 61, 66, 67, 85, 86, 98	23, 27, 32, 37, 49, 50, 55, 62, 69, 74, 77, 82, 83, 101, 102, 114	Ground
36	48	GND	07, 11, 16, 21, 33, 34, 39, 46, 53, 58, 61, 66, 67, 85, 86, 98	23, 27, 32, 37, 49, 50, 55, 62, 69, 74, 77, 82, 83, 101, 102, 114	Ground
37	14	AD22	36	52	Address/Data 22
38	49	AD23	31	47	Address/Data 23
39	15	AD20	38	54	Address/Data 20
40	50	AD21	35	51	Address/Data 21
41	16	AD18	42	58	Address/Data 18
42	51	AD19	37	53	Address/Data 19
43	17	AD16	44	60	Address/Data 16
44	52	AD17	41	57	Address/Data 17
45	18	/FRAME	48	64	FRAME is driven by the current master to indicate the beginning and duration of an access. While FRAME is asserted, data transaction continues. When FRAME is deasserted, the transaction is in the final data phase.
46	53	/C/BE2	43	59	Command/Byte Enable 3 // These inputs are the multiplexed Bus Command and Byte Enable signals on the PCI bus.
47	19	GND	07, 11, 16, 21, 33, 34, 39, 46, 53, 58, 61, 66, 67, 85, 86, 98	23, 27, 32, 37, 49, 50, 55, 62, 69, 74, 77, 82, 83, 101, 102, 114	Ground
48	54	GND	07, 11, 16, 21, 33, 34, 39, 46, 53, 58, 61, 66, 67, 85, 86, 98	23, 27, 32, 37, 49, 50, 55, 62, 69, 74, 77, 82, 83, 101, 102, 114	Ground
49	20	/TRDY	50	66	TRDY indicates the PCI bus slave can complete the current data phase of the transaction.
50	55	/IORDY	45	61	IRDY indicates the PCI bus master can complete the current data phase of the transaction.
51	21	/STOP	52	68	STOP indicates the connected device is requesting that the current master stop the current transaction.
52	56	/DEVSEL	56	72	The connected device drives this signal active to indicate that it has decoded its address as the target of the current access.
53	22	PAR	40	56	The connected device drives PAR in read data phases for parity checking.
54	57	/PERR	55	71	The PERR pin reports data parity errors during data read phases. Even parity over AD[31:00] and C/BE[3:0]#
55	23	AD15	60	76	Address/Data 15
56	58	/SERR	51	67	System error
57	24	AD13	62	78	Address/Data 13
58	59	/C/BE1	57	73	Command/Byte Enable 1 // These inputs are the multiplexed Bus Command and Byte Enable signals on the PCI bus.
59	25	AD11	64	80	Address/Data 11
60	60	AD14	59	75	Address/Data 14
61	26	GND	07, 11, 16, 21, 33, 34, 39, 46, 53, 58, 61, 66, 67, 85, 86, 98	23, 27, 32, 37, 49, 50, 55, 62, 69, 74, 77, 82, 83, 101, 102, 114	Ground
62	61	GND	07, 11, 16, 21, 33, 34, 39, 46, 53, 58, 61, 66, 67, 85, 86, 98	23, 27, 32, 37, 49, 50, 55, 62, 69, 74, 77, 82, 83, 101, 102, 114	Ground
63	27	AD09	68	84	Address/Data 09
64	62	AD12	63	79	Address/Data 12
65	28	/C/BE0	70	86	Command/Byte Enable 0 // These inputs are the multiplexed Bus Command and Byte Enable signals on the PCI bus.
66	63	AD10	65	81	Address/Data 10
67	29	AD06	74	90	Address/Data 06
68	64	AD08	69	85	Address/Data 08
69	30	AD04	76	92	Address/Data 04
70	65	AD07	71	87	Address/Data 07
71	31	GND	07, 11, 16, 21, 33, 34, 39, 46, 53, 58, 61, 66, 67, 85, 86, 98	23, 27, 32, 37, 49, 50, 55, 62, 69, 74, 77, 82, 83, 101, 102, 114	Ground
72	66	GND	07, 11, 16, 21, 33, 34, 39, 46, 53, 58, 61, 66, 67, 85, 86, 98	23, 27, 32, 37, 49, 50, 55, 62, 69, 74, 77, 82, 83, 101, 102, 114	Ground
73	32	AD02	78	94	Address/Data 02
74	67	AD05	75	91	Address/Data 05
75	33	AD00	80	96	Address/Data 00
76	68	AD03	79	95	Address/Data 03
77	-	SIORXD[0]			Southbridge Serial Receive
78	69	AD01	83	99	Address/Data 01
79	-	SIOTXD[0]			Southbridge Serial Transceive
80	34	/SW_PCI			?switch PCI?

South Bridge serial

Pad	Name	Usage	Remark
JL9385	+3.3V_SB_VDDIO	VCC
JL9386	GND	Ground
JL9387	SB_SIO0-RXD	Receive
JL9388	SB_SIO0-TXT	Tranceive

160 pin pad layout

CN4301 160P on DECR-1000 TMU-520 (only partly used for PCI)
TODO