Syscon Thermal Config/structs

This page is only intended to show some code samples, feel free to improve them, please provide a proof if an important change is made, and use the related Discussion page/s for the dicussions and speculations

ps3_syscon_eeprom_thermal_config_region.c

// SYSCON          | THERMAL CONFIG FMT | BOARDS
//---------------------------------------------------------------
// CXR713F120A     | mullion_flash      | MPU-501, TMU-520, COOKIE-XX prototypes
// CXR713120-201GB | mullion_old        | COK-001
// CXR713120-202GB | mullion_old        | COK-002
// CXR713120-203GB | mullion_new        | SEM-001
// CXR714120-301GB | mullion_new        | DIA-001
// CXR714120-302GB | mullion_new        | DIA-002, DEB-001
// CXR714120-303GB | mullion_new        | COK-002 (Refurb 65nm RSX)
// CXR714120-304GB | mullion_new        | COK-001, DIA-001 (Refurbs 40nm RSX)
// SW-301          | sherwood           | VER-001
// SW-302          | sherwood           | VER-001
// SW2-301         | sherwood           | DYN-001
// SW2-302         | sherwood           | SUR-001
// SW2-303         | sherwood           | JTP-001, JSD-001
// SW3-301         | sherwood           | KTE-001
// SW3-302         | sherwood           | MSX-001, MPX-001, NPX-001
// SW3-303         | sherwood           | ?
// SW3-304         | sherwood           | PQX-001, PPX-001, RTX-001, REX-001

struct fancon_footer {
	u8 duty_min;              // Always 0x33 (PS3 Fats and Slims DYN-001, SUR-001, JTP-001, JSD-001), or always 0x34 (PS3 Slim KTE-001 and SuperSlims)
	u8 duty_max;              // Always 0xFF
	u8 policy;                // 0x00=Full, 0x01=Auto Table, 0x02=Manual
	u8 select;                // 0x00=EEPROM, 0xFF=RAM
	u8 active;                // 0x00=Inactive, 0xFF=Active
};

struct fancon_40 {
	u8  duty[0xA];
	u16 tempu[0xA];
	u16 tempd[0xA];
	fancon_footer;
	u8 reserved[0x9];
}; // 0x40

struct fancon_80 {
	u8  duty[0x14];
	u16 tempu[0x14];
	u16 tempd[0x14];
	fancon_footer;
	u8 reserved[0x17];
}; // 0x80

struct fancon_sw {
	u8  duty;
	u16 tempu;
	u16 tempd;
};

struct fancon_70 {
	fancon_sw[0x14];
	fancon_footer;
	u8 reserved[0x7];
}; // 0x70


struct config_footer_temps  {
	u16 trp;                  // Thermal Protection ? (usually 1ºC lower than tshutdown)
	u16 tshutdown;            // Thermal Shutdown (usually the same temperature than the highest value of TempU)
	u16 hyst;                 // Hysteresis (usually 2ºC)
};

struct config_footer_unk_1  {
	u8 unk_1_cell;            // always 0xFF
	u8 unk_1_rsx;             // always 0xFF
	u8 unk_1_bevr;            // always 0xFF
	u8 unk_1_sb;              // always 0xFF
	u8 unk_1_eegs;            // always 0xFF
};

struct config_footer_unk_2  {
	u8 unk_2_cell;            // directly or indirectly related with cell revision
	u8 unk_2_rsx;             // directly or indirectly related with rsx revision
	u8 unk_2_bevr;            // directly or indirectly related with bevr revision
	u8 unk_2_sb;              // directly or indirectly related with sb revision
	u8 unk_2_eegs;            // directly or indirectly related with eegs revision
};

struct config_footer_unk_3  {
	u8 unk_3_cell;            // identical to unk_2_cell (only mullion, sherwood doesnt seems to use this area)
	u8 unk_3_rsx;             // identical to unk_2_rsx (only mullion, sherwood doesnt seems to use this area)
	u8 unk_3_bevr;            // always 0xFF, bevr fan table is not active (only mullion, sherwood doesnt seems to use this area)
	u8 unk_3_sb;              // identical to unk_2_sb (only mullion, sherwood doesnt seems to use this area)
	u8 unk_3_eegs;            // always 0xFF, eegs fan table is not active (only mullion, sherwood doesnt seems to use this area)
}; //


struct config_footer_mullionf {
	u8  use_eeprom_values;    // (00 = yes)
	u8  reserved;
	config_footer_temps cell;
	config_footer_temps rsx;
	config_footer_temps xdr;
	config_footer_temps intake;
	config_footer_temps gbe;
	config_footer_temps sb;
	u8  reserved[0xA];
	u16 tshutdown_time;       // TShutdown Time:%d[s](0x%04x)
	u8  unknown_0;            // related to thermal errors
	u8  fan_shutdown_time;
	u8  reserved[0xC];
	u8  rsx_thermal_limit_unk0;
	u8  rsx_thermal_limit_unk1;
	u8  rsx_thermal_limit_unk2;
	u8  rsx_thermal_limit_unk3;
	u8  rsx_thermal_limit_unk4;
	u8  rsx_thermal_limit_unk5;
	u8  reserved[0xA];
	u8  unknown_1;            // fan config
	u8  unknown_2;            // fan config
	u8  unknown_3;            // fan config
	u8  reserved[0xD];
	u8  unknown_4;            // fan config (set to 0xE0)
	u16 unknown_5;            // fan config
	u16 unknown_6;            // fan config
	u16 unknown_7;            // fan config
	u16 unknown_8;            // fan config
	u16 unknown_9;            // fan config
	u8  reserved[0x95];
}; // 0x100

struct config_footer_mullion {
	u16 tshutdown_time;       // TShutdown Time:%d[s](0x%04x). Always 0xFFFF
	u8  unk_00;               // Fan shutdown time ?
	u8  fan_initial_duty;     // Fan initial duty: %d%%(0x%02x). Always 0x4D (PS3 Fats with mullion)
	u8  fan_initial_time;     // Fan initial time: %d(ms). Always 0x14
	config_footer_unk_1;
	config_footer_unk_2;
	u8  unk_FF;
	config_footer_temps cell;
	config_footer_temps rsx;
	config_footer_temps bevr;
	config_footer_temps sb;
	config_footer_temps eegs;
	config_footer_unk_3;
	u8  reserved[0x4B];
	u16 checksum;
}; // 0x80

struct config_footer_sherwood {
	u16 tshutdown_time;       // TShutdown Time:%d[s](0x%04x). Always 0xFFFF
	u16 unk_0000;             // Fan shutdown time ?, length increased to 2 bytes for sherwoods ?
	u8  fan_initial_duty;     // Fan initial duty: %d%%(0x%02x). 0x4D (PS3 Fat VER-001 and Slim DYN-001), or 0x40 (Slims SUR-001, JTP-001, JSD-001), or 0x41 (Slim KTE-001 and SuperSlims)
	u8  fan_initial_time;     // Fan initial time: %d(ms). Always 0x14
	config_footer_unk_1;
	config_footer_unk_2;
	config_footer_temps cell;
	config_footer_temps rsx;
	config_footer_temps sb;
	u8  reserved[0x8E];
}; // 0xB0


struct thermal_config {
#ifdef mullion_flash
	fancon_40 cell;           // FanconNo=0, TZoneNo=0x00 "1st BE Primary"
	fancon_40 rsx;            // FanconNo=1, TZoneNo=0x01 "RSX Primary"
	fancon_40 unk_z20;        // FanconNo=2, TZoneNo=0x20 unknown
	fancon_40 unk_z21;        // FanconNo=3, TZoneNo=0x21 unknown
	fancon_40 xdr;            // FanconNo=4, TZoneNo=0x02 "XDR Primary"
	fancon_40 intake;         // FanconNo=7, TZoneNo=0x0A "Air Intake"
	fancon_40 gbe;            // FanconNo=6, TZoneNo=0x0F "GbE"
	fancon_40 sb;             // FanconNo=5, TZoneNo=0x14 "SB"
	config_footer_mullionf;
#endif
#ifdef mullion_old
	fancon_40 cell;           // FanconNo=0, TZoneNo=0x00 "1st BE Primary"
	fancon_40 rsx;            // FanconNo=1, TZoneNo=0x01 "RSX Primary"
	fancon_40 bevr;           // FanconNo=?, TZoneNo=0x03 "BE VR"
	fancon_40 sb;             // FanconNo=3, TZoneNo=0x14 "SB"
	fancon_40 eegs;           // FanconNo=?, TZoneNo=0x15 "EE+GS"
	fancon_40 reserved;
	config_footer_mullion;
#endif
#ifdef mullion_new
	fancon_80 cell;           // FanconNo=0, TZoneNo=0x00 "1st BE Primary"
	fancon_80 rsx;            // FanconNo=1, TZoneNo=0x01 "RSX Primary"
	fancon_80 sb;             // FanconNo=2, TZoneNo=0x14 "SB"
	config_footer_mullion;
#endif
#ifdef sherwood
	fancon_70 cell;           // FanconNo=0, TZoneNo=0x00 "1st BE Primary"
	fancon_70 rsx;            // FanconNo=1, TZoneNo=0x01 "RSX Primary"
	fancon_70 sb;             // FanconNo=?, TZoneNo=0x14 "SB"
	config_footer_sherwood;
#endif
};