Talk:Remarry Bluray Drive

<Pereb> On FW 3.50 you get Drive init FAIL. I don't know about 3.21-3.42. I downgraded to 3.15 myself for it to work
[...]
<Pereb> I was on FW 3.50. I did service mode. Put usb stick with cfg that had update enabled, and FW 2.30 PUP = drive init fail
<Pereb> I downgraded to 3.15 via QA. Used the exact same remarry files = drive init pass

---

• standalone.cfg settings file (translated to english)

   ###############################################
   # Configuration file for Diag
   # Quality Assurance
   # WLAN & BT RSSI measurement
   #
   # 2006/09/06 kyoshida
   # Detect the presence or absence of Eurus support
   # 2006/10/10 kyoshida
   # Standard for the RSSI value
   # Follow the "Guidelines for inspection and adjustment. 06.10.05" (YYMMDD)
   ###############################################
   #=== Common Settings =================================
   #
   # Set the measurement mode
   #
   # 0 = Standard inspection (1 time)
   # 1 = Repeated measurement for Debug
   # ----------------------------------------------------
   0
   #=== Common Settings =================================
   #
   # In case of standard inspection you can shut down the RSSI.
   #
   #   0 = Do not shutdown.
   #   1 = Do shutdown.
   #-----------------------------------------------------
   0
   #=== Common Settings =================================
   #
   # *Valid only if shutdown = 00
   #
   # Controls what led does in case of (-OK-) on standard RSSI
   #
   # LED ID
   #
   #   1 = POWER(green)
   #   2 = STATUS(red)
   #
   # LED ACTION
   #
   #   0 = OFF
   #   1 = ON
   #   2 = BLINK FAST
   #   3 = BLINK SLOW
   #------------------------------------------------------
   #<1>------
   # LED ID
   1
   # LED ACTION
   1
   #<2>------
   # LED ID
   2
   # LED ACTION
   0
   #=== Common Settings ==================================
   #
   # *Valid only if shutdown = 00
   #
   # Controls what led does in case of (-NG-) on standard RSSI
   #
   # LED ID
   #
   #   1 = POWER(green)
   #   2 = STATUS(red)
   #
   # LED ACTION
   #
   #   0 = OFF
   #   1 = ON
   #   2 = BLINK FAST
   #   3 = BLINK SLOW
   #------------------------------------------------------
   #=== WLAN configuration =================================
   #
   # <Decimal input>
   #
   # Settings for RSSI measurement? Set of:
   #
   #   0 = Do not measure
   #   1 = Do measure
   #   2 = Measure using HW config for Eurus
   #
   # RSSI Standard
   #
   #   min[dBm]
   #   max[dBm]
   #
   # OK count
   # NG count
   #
   # Estimated measurement time per loop
   #   [Number of measured channels] × 100msec
   #----------------------------------------------
   # <ANTENNA A>
   0
   -80
   -20
   2
   200
   # <ANTENNA B>
   0
   -80
   -20
   2
   200
   # <ANTENNA DIVERSITY>
   0
   -80
   -20
   2
   200
   #=== WLAN configuration =================================
   #
   # <Decimal input>
   #
   # Set RSSI channel measurements
   # Specify 1 - 13
   #
   #   channel < 14 = Do measure
   #   channel > 13 = Do not measure (CH number less than or equal to 255)
   #
   #--------------------------------------------------------
   # If you want to measure all from 1 to 13ch
   1
   2
   3
   4
   5
   6
   7
   8
   9
   10
   11
   12
   13
   ###############################################
   # samples
   # If you want to measure a specific channel
   ##############################################
   #1
   #13
   #77
   #77
   #77
   #77
   #77
   #77
   #77
   #77
   #77
   #77
   #77
   #END-samples----------------------------------
   #=== Access Point Test Connection settings ===
   #
   # Settings for RSSI measurement? Set of:
   #
   #   0 = Do not measure
   #   1 = Do measure
   #   2 = Measure using HW config for Eurus
   #
   # OK count
   # NG count
   #
   # Estimated measurement time per loop
   #   100msec
   #
   # <AP>
   #   SSID
   #   IP ADDRESS
   #
   # <COOKIE>
   #   IP ADDRESS
   #   NETMASK
   #   DEFAULT ROUTE
   #   PRIMARY DNS
   #
   #----------------------------------------------
   0
   10
   300
   #<AP>
   LV2DIAG-AP
   192.168.1.1
   #<COOKIE>
   192.168.1.100
   255.255.255.0
   192.168.1.1
   192.168.1.1
   #=== BT Settings ==============================
   #
   # <Decimal input>
   #
   # Settings for RSSI measurement? Set of:
   #
   #   0 = Do not measure
   #   1 = Do measure
   #
   # RSSI Standard
   #
   #   min[dBm]
   #   max[dBm]
   #
   # OK count
   # NG count
   #
   # Estimated measurement time per loop
   #   100msec
   #----------------------------------------------
   # <ANTENNA 1>
   0
   -60
   -1
   2
   300
   # <ANTENNA 2>
   0
   -60
   -1
   2
   30
   # <ANTENNA DIVERSITY>
   0
   -60
   -1
   2
   30
   #=== CS Only ================================
   #
   # LED Lighting pattern when removing the controller
   #
   # LED ID
   #
   #   1 = POWER(green)
   #   2 = STATUS(red)
   #
   # LED ACTION
   #
   #   0 = OFF
   #   1 = ON
   #   2 = BLINK FAST
   #   3 = BLINK SLOW
   #--------------------------------------------
   #<1>------
   # LED ID
   1
   # LED ACTION
   2
   #<2>------
   # LED ID
   2
   # LED ACTION
   0
   #=== Other items ===================
   # to be executed after WLAN and BT inspection
   #----------------------------------------------
   # Drive Init
   #   0 = Do not perform
   #   1 = Do perform
   #----------------------------------------------
   1
   #---------------------------------------------
   # Install Systemsoftware
   #   0 = Do not perform
   #   1 = Do perform
   #----------------------------------------------
   0
   #---------------------------------------------
   # freebdp
   #   0 = Do not perform
   #   1 = Do perform
   #----------------------------------------------
   1
   #---------------------------------------------
   # Name of file used for Install Systemsoftware
   #----------------------------------------------
   manufacturing_updater_for_reset.self

http://pastebin.com/3PwAVi6s