Syscon Hardware

Syscon 1st Generation (BGA Packaging)

Syscon is the main power controller chip. It is responsible for powering up the various power systems and for configuring and initialising the CELL BE, RSX and South Bridge. It communicates with these devices via seperate SPI busses. There is external access by JTAG (disabled at factory by blowing a fuse), an EEPROM programming interface and Serial (UART). The Syscon is a SoC and consists of an ARM7TDMI (ARMv4) CPU, a 256KB EEPROM and 16KB RAM.

Serialnumbers @ SKU

Retail

Model	Type	Board	Syscon part no.	Soft Id.	Notes
CECHAxx	0x01	COK-001	CXR713120-201GB	0B8E
CECHBxx	0x02	COK-001	CXR713120-201GB	0B8E
CECHCxx	0x03	COK-002	CXR713120-201GB   or CXR713120-202GB	0C16
CECHDxx	SKU never released
CECHExx	0x04	COK-002   or COK-002W	CXR713120-201GB   or CXR713120-202GB	0C16
CECHFxx	SKU never released
CECHGxx	0x05	SEM-001	CXR713120-201GB   or CXR713120-202GB   or CXR713120-203GB	0D52
CECHHxx	0x06	DIA-001	CXR714120-301GB	0DBF
CECHIxx	SKU never released
CECHJxx	0x07	DIA-002	CXR714120-301GB   or CXR714120-302GB	0E69
CECHKxx	0x07	DIA-002	CXR714120-301GB   or CXR714120-302GB	0E69
CECHLxx	0x08	VER-001	SW-301   or SW-302	065D
CECHMxx	0x08	VER-001	SW-301   or SW-302	065D
CECHNxx	SKU never released
CECHOxx	SKU never released
CECHPxx	0x08	VER-001	SW-301   or SW-302	065D
CECHQxx	0x08	VER-001	SW-301   or SW-302	065D
CECH-20xx	0x09	DYN-001	SW2-301	0832
CECH-21xx	0x0A	SUR-001	SW2-301   or SW2-302	08A0
CECH-25xx	0x0B	JTP-001   or JSD-001	SW2-301  or SW2-302  or SW2-303	08C2
CECH-30xx	0x0C	KTE-001	SW2-301  or SW2-302  or SW2-303	0918
CECH-40xx	0x0D	MSX-001   or MPX-001	SW3-302	098F

nbsp;

Prototypes

Model	Type	Board	Syscon part no.	Soft Id.	Active JTAG	Notes
DECR1000(A/J)	0x01	TMU-520	CXR713F120A	03FB	?
DEH-H1000A(S)(-E(S))	0x01	COK-001 (Prototype)	CXR713F120A	0B67	?
DEH-H1001-D	0x01	COOKIE-13	CXR713F120A	?0B67?	?

---

Not mentioned:

0F29 - ?
0F38 - ?

Syscon Externalised Ports

Note: for more specific information per model, see the links to each subppage in the Serialnumbers @ SKU table.

Syscon UART

BGA	Name	Description
P16	UART0_TxD	Serial Transmit
P15	UART0_RxD	Serial Receive

You can attach a 3.3v TTL cable (LV-TTL) to the UART on syscon (UART0_TxD, UART0_RxD). Baud rate is 57600. There is a simple plaintext protocol involved. This varies on different syscon models. Example:

<command>:<hash>

Where the hash is the sum of command bytes & 0xFF

you should terminate commands with \r\n, the syscon messages are only terminated with \n

Here are some of the commands/messages encountered:

Messages:
Power applied (standby mode)
OK 00000000:3A

Power on
# (PowerOn State):7F

Power off (Hard shutdown)
# (PowerOff State):DD

After Fan test:
# (PowerOff State) (Fatal):36

No text, invalid hash:
NG F0000002:4D

Commands:
VER:ED
OK 00000000 S1E 00 00 065D:A4

ERRLOG:CB
OK 00000000:3A

DATE:1E
NG F0000003:4E

Syscon (SPI) EEPROM

BGA	Name	Description
F16	CSB	Chip Select (needs always 3.3V )
H16	DO	Serial Data Output
G16	DI	Serial Data Input
E16	SKB	Serial Data Clock
U15	WCB	Write Protect
U16	RBB	Read Data back (Verify)

Syscon JTAG

disabled in factory after production on retailmodels

BGA	Name	Description
L8	JRTCK	Return Test Clock
K8	JTCK	Test Clock
K9	JTDO	Test Data Out
L9	JTMS	Test Mode State / Test Mode Select
K7	JTDI	Test Data In
L7	JNTAST	Write Protect

Syscon Underlaying ports

Syscon Cell SPI Bus

BGA	Name	Description
M2	/BE_SPI_CS	Chip Select
N2	BE_SPI_DO	Serial Data Output
M1	BE_SPI_DI	Serial Data Input
N1	BE_SPI_CLK	Serial Data Clock
P2	/BE_RESET	CellBE Reset
P1	BE_POWGOOD	CellBE PowerGood
T2	/BE_INT	CellBE Interrupt

Syscon Southbridge SPI Bus

BGA	Name	Description
B9	/SB_SPI_CS	Chip Select
B8	SB_SPI_DO	Serial Data Output
A9	SB_SPI_DI	Serial Data Input
A8	SB_SPI_CLK	Serial Data Clock