Editing Template:HSW-001 pinout

Jump to navigation Jump to search
Warning: You are not logged in. Your IP address will be publicly visible if you make any edits. If you log in or create an account, your edits will be attributed to your username, along with other benefits.

The edit can be undone. Please check the comparison below to verify that this is what you want to do, and then publish the changes below to finish undoing the edit.

Latest revision Your text
Line 1: Line 1:
{| class="wikitable"
{| class="wikitable"
|+[[HSW-001]] Pinout {{ed right|HSW-001 pinout}}
|+HSW-001 Pinout {{ed right|HSW-001 pinout}}
! rowspan="2" | Pin !! rowspan="2" | Name !! colspan="2" | Connected to !! rowspan="2" | Description
! rowspan="2" | Pin !! colspan="2" | Signal/Connected to !! rowspan="2" | Description
|-
|-
! On [[Motherboard_Revisions|Motherboard]] !! On [[Switch_boards|Switch board]]
! On Motherboard<!--// <BR />(Syscon [[SW2-30x]] pins)  //-->  !! On Switch board
|-{{cellcolors|grey|#ffffff}}
| 1 || pin12 @ Syscon [[SW2-30x]] || 4x CONTOUR LEDs || On Switch board is connected to a transistor driving 2 LEDs with currentlimitor resistors of 3K {{ohm}} (red led at left-top) and 820 {{ohm}} (blue led at left-bottom)
|-{{cellcolors|#cc3333|#ffffff}}
| 2 || pin1 @ CN101 [[Power Supply]] || VCC || +5V Standby line from power supply connector CN101, the pin named 5V_EVER on motherboard and 5VSB on power supply
|-
|-
| 1 || {{cellcolors|darkgrey|white}} SW_PWM ? || Syscon [[Template:Syscon_pinout_LQFP_128_pins|SW2-30x]], pin 12 || 4x CONTOUR LEDs, transistor base pin || The transistor is located in the switch board and drives 2 LEDs with currentlimitor resistors of 3K {{ohm}} (red led at left-top) and 820 {{ohm}} (blue led at left-bottom)<br>The circuit has unpopulated pads to add another transistor and another 2 LEDs for a total of 4 LEDs driven by <abbr title="the line is inactive in all known working modes, the leds never emits light because syscon never sends the signal">a misterious syscon pin</abbr>
| 3 || pin11 @ Syscon [[SW2-30x]] || 4x WHITE LEDs, ground pins || Inner light for power and eject switches, power LEDs with a currentlimitor resistor of 1K {{ohm}}, and eject LEDs with a currentlimitor resistor of 910 {{ohm}}
|-{{cellcolors|#333333|#ffffff}}
| 4 || GND || GND || Ground
|-
|-
| 2 || {{cellcolors|#CC3333|white}} +5V_EVER || [[Power Supply]] Connector (CN101), pin 1 || VCC || 5V Standby line from power supply connector CN101, the pin named 5V_EVER on motherboard and 5VSB on power supply
| 5 || pin111 @ Syscon [[SW2-30x]] || EJECT switch || Sink to ground to activate
|-
|-
| rowspan="2" | 3 || rowspan="2" | ? || rowspan="2" | Syscon [[Template:Syscon_pinout_LQFP_128_pins|SW2-30x]], pin 11 || 2x White leds - || Inner LEDs for EJECT button backlight, with a currentlimitor resistor of 910 {{ohm}}
| 6 || pin110 @ Syscon [[SW2-30x]] || POWER switch || Sink to ground to activate
|-
|-
| 2x White leds - || Inner LEDs for POWER button backlight, with a currentlimitor resistor of 1K {{ohm}}
| 7 || pin5 @ Syscon [[SW2-30x]] || GREEN led, ground pin || Connects to left-bottom corner pin (green gnd) of dual red/green LED over power switch, with a currentlimitor resistor of 1K {{ohm}}
|-
|-
| 4 || {{cellcolors|#333333|white}} GND || GND || GND || Ground
| 8 || pin6 @ Syscon [[SW2-30x]] || RED led, ground pin || Connects to left-top corner pin (red gnd) of dual red/green LED over power switch, with a currentlimitor resistor of 1K2 {{ohm}}
|-
|-
| 5 || EJECT_SW || Syscon [[Template:Syscon_pinout_LQFP_128_pins|SW2-30x]], pin 111 || Eject switch {{buttoneject}} || Sink to ground to activate
| 9 || pin 36 @ BD controller [[CXD5131R-1]] || BLUE led, ground pin || Connects to blue LED over eject switch, with a currentlimitor resistor of 560 {{ohm}}
|-{{cellcolors|#333333|#ffffff}}
| 10 || GND || GND || Ground
|-
|-
| 6 || POW_SW || Syscon [[Template:Syscon_pinout_LQFP_128_pins|SW2-30x]], pin 110 || Power switch {{buttonpower}} || Sink to ground to activate
|-
| 7 || POW_LED || Syscon [[Template:Syscon_pinout_LQFP_128_pins|SW2-30x]], pin 5 || Green led - || Connects to left-bottom corner pin (green gnd) of ''dual red/green LED'' located next to the power switch, with a currentlimitor resistor of 1K {{ohm}}
|-
| 8 || STBY_LED || Syscon [[Template:Syscon_pinout_LQFP_128_pins|SW2-30x]], pin 6 || Red led - || Connects to left-top corner pin (red gnd) of ''dual red/green LED'' located next to the power switch, with a currentlimitor resistor of 1K2 {{ohm}}
|-
| 9 || BD_LED || BluRay controller [[CXD5131R-1]], pin 36 (on [[SUR-001]]/[[JSD-001]])<br>''or''<br>BluRay controller [[R8J32830FPV1]], pin ?? (on [[JTP-001]])|| Blue led - || Connects to blue LED located next to the eject switch, with a currentlimitor resistor of 560 {{ohm}}
|-
| 10 || {{cellcolors|#333333|white}} GND || GND || GND || Ground
|}
|}
<noinclude>[[Category:Templates]]</noinclude>
<noinclude>[[Category:Templates]]</noinclude>
Please note that all contributions to PS3 Developer wiki are considered to be released under the GNU Free Documentation License 1.2 (see PS3 Developer wiki:Copyrights for details). If you do not want your writing to be edited mercilessly and redistributed at will, then do not submit it here.
You are also promising us that you wrote this yourself, or copied it from a public domain or similar free resource. Do not submit copyrighted work without permission!

To protect the wiki against automated edit spam, we kindly ask you to solve the following hCaptcha:

Cancel Editing help (opens in new window)

Templates used on this page:

Retrieved from "http://www.psdevwiki.com/ps3/Template:HSW-001_pinout"