Editing Template:CSW-001 pinout

Jump to navigation Jump to search
Warning: You are not logged in. Your IP address will be publicly visible if you make any edits. If you log in or create an account, your edits will be attributed to your username, along with other benefits.

The edit can be undone. Please check the comparison below to verify that this is what you want to do, and then publish the changes below to finish undoing the edit.

Latest revision Your text
Line 7: Line 7:
| 1 || {{cellcolors|#333333|white}} GND || GND || GND || Ground
| 1 || {{cellcolors|#333333|white}} GND || GND || GND || Ground
|-
|-
| 2 || {{cellcolors|darkgrey|white}} SW_PWM || [[Template:Syscon_pinout_BGA_200_pads|Syscon]] pad N9 || Testpad ? || FREQ. Intended to send a [https://en.wikipedia.org/wiki/Pulse-width_modulation PWM] signal to the switch board ?
| 2 || {{cellcolors|darkgrey|white}} SW_PWM || [[Template:Syscon_pinout_BGA_200_pads|Syscon Mullion]], pad N9 || Testpad ? || FREQ. Intended to send a [https://en.wikipedia.org/wiki/Pulse-width_modulation PWM] signal to the switch board ?
|-
|-
| 3 || {{cellcolors|#44cc44|white}} RMC_IN || [[Template:Syscon_pinout_BGA_200_pads|Syscon]] pad R10<br>[[Service Connectors#CN4009|Service Connector]] (CN4009) pin 17 || Testpad ?. <abbr title="missing resistor>NC</abbr> || '''R'''e'''M'''ote '''C'''ontrol '''IN'''put<br>The IR receiver component is missing in the Switch board but existed in some PS3 prototypes that was using [https://www.sbprojects.net/knowledge/ir/sirc.php SIRC protocol] and [[SC_Communication#Syscon_Services|SERV_SIRCS]]
| 3 || {{cellcolors|#44cc44|white}} RMC_IN || [[Template:Syscon_pinout_BGA_200_pads|Syscon Mullion]], pad R10<br>[[Service Connectors#CN4009|Service Connector]] (CN4009) pin 17 || Testpad ?. <abbr title="missing resistor>NC</abbr> || IR Remote Control (input)
|-
|-
| 4 || POW_SW || [[Template:Syscon_pinout_BGA_200_pads|Syscon]] pad B12 || Power Switch {{buttonpower}} ||  
| 4 || POW_SW || [[Template:Syscon_pinout_BGA_200_pads|Syscon Mullion]], pad B12 || Power Switch {{buttonpower}} ||  
|-
|-
| 5 || EJECT_SW || [[Template:Syscon_pinout_BGA_200_pads|Syscon]] pad A12 || Eject Switch {{buttoneject}} ||  
| 5 || EJECT_SW || [[Template:Syscon_pinout_BGA_200_pads|Syscon Mullion]], pad A12 || Eject Switch {{buttoneject}} ||  
|-
|-
| 6 || POW_LED || [[Template:Syscon_pinout_BGA_200_pads|Syscon]] pad M7 || Green led ||  
| 6 || POW_LED || [[Template:Syscon_pinout_BGA_200_pads|Syscon Mullion]], pad M7 || Green led ||  
|-
|-
| 7 || STBY_LED || [[Template:Syscon_pinout_BGA_200_pads|Syscon]] pad N7 || Red led ||  
| 7 || STBY_LED || [[Template:Syscon_pinout_BGA_200_pads|Syscon Mullion]], pad N7 || Red led ||  
|-
|-
| 8 || BD_LED || BluRay connector (CN3221) pin 50 || Blue led ||  
| 8 || BD_LED || BluRay Connector, pin ? || Blue led ||  
|-
|-
| 9 || {{cellcolors|#333333|white}} GND || GND || GND || Ground
| 9 || {{cellcolors|#333333|white}} GND || GND || GND || Ground
|-
|-
| 10 || {{cellcolors|#CC3333|white}} +5V_EVER || [[Power Supply]] connector (CN6005) pins 4 and 5 || VCC || 5V Standby
| 10 || {{cellcolors|#CC3333|white}} +5V_EVER || [[Power Supply]] <abbr title="CN???>Connector</abbr>, pins 4/5 ? || VCC || 5V Standby
|}
|}
<noinclude>[[Category:Templates]]</noinclude>
<noinclude>[[Category:Templates]]</noinclude>
Please note that all contributions to PS3 Developer wiki are considered to be released under the GNU Free Documentation License 1.2 (see PS3 Developer wiki:Copyrights for details). If you do not want your writing to be edited mercilessly and redistributed at will, then do not submit it here.
You are also promising us that you wrote this yourself, or copied it from a public domain or similar free resource. Do not submit copyrighted work without permission!

To protect the wiki against automated edit spam, we kindly ask you to solve the following hCaptcha:

Cancel Editing help (opens in new window)

Templates used on this page:

Retrieved from "http://www.psdevwiki.com/ps3/Template:CSW-001_pinout"