Editing Talk:Remarry Bluray Drive

[[Category:Software]][[Category:Hardware]]
 <Pereb> On FW 3.50 you get Drive init FAIL. I don't know about 3.21-3.42. I downgraded to 3.15 myself for it to work
 [...]
 <Pereb> I was on FW 3.50. I did service mode. Put usb stick with cfg that had update enabled, and FW 2.30 PUP = drive init fail
 <Pereb> I downgraded to 3.15 via QA. Used the exact same remarry files = drive init pass

----

*'''standalone.cfg''' settings file (translated to english)
    ###############################################
    # Configuration file for Diag
    # Quality Assurance
    # WLAN & BT RSSI measurement
    #
    # 2006/09/06 kyoshida
    # Detect the presence or absence of Eurus support
    # 2006/10/10 kyoshida
    # Standard for the RSSI value
    # Follow the "Guidelines for inspection and adjustment. 06.10.05" (YYMMDD)
    ###############################################
    #=== Common Settings =================================
    #
    # Set the measurement mode
    #
    # 0 = Standard inspection (1 time)
    # 1 = Repeated measurement for Debug
    # ----------------------------------------------------
    0
    #=== Common Settings =================================
    #
    # In case of standard inspection you can shut down the RSSI.
    #
    #   0 = Do not shutdown.
    #   1 = Do shutdown.
    #-----------------------------------------------------
    0
    #=== Common Settings =================================
    #
    # *Valid only if shutdown = 00
    #
    # Controls what led does in case of (-OK-) on standard RSSI
    #
    # LED ID
    #
    #   1 = POWER(green)
    #   2 = STATUS(red)
    #
    # LED ACTION
    #
    #   0 = OFF
    #   1 = ON
    #   2 = BLINK FAST
    #   3 = BLINK SLOW
    #------------------------------------------------------
    #<1>------
    # LED ID
    1
    # LED ACTION
    1
    #<2>------
    # LED ID
    2
    # LED ACTION
    0
    #=== Common Settings ==================================
    #
    # *Valid only if shutdown = 00
    #
    # Controls what led does in case of (-NG-) on standard RSSI
    #
    # LED ID
    #
    #   1 = POWER(green)
    #   2 = STATUS(red)
    #
    # LED ACTION
    #
    #   0 = OFF
    #   1 = ON
    #   2 = BLINK FAST
    #   3 = BLINK SLOW
    #------------------------------------------------------
    #=== WLAN configuration =================================
    #
    # <Decimal input>
    #
    # Settings for RSSI measurement? Set of:
    #
    #   0 = Do not measure
    #   1 = Do measure
    #   2 = Measure using HW config for Eurus
    #
    # RSSI Standard
    #
    #   min[dBm]
    #   max[dBm]
    #
    # OK count
    # NG count
    #
    # Estimated measurement time per loop
    #   [Number of measured channels] × 100msec
    #----------------------------------------------
    # <ANTENNA A>
    0
    -80
    -20
    2
    200
    # <ANTENNA B>
    0
    -80
    -20
    2
    200
    # <ANTENNA DIVERSITY>
    0
    -80
    -20
    2
    200
    #=== WLAN configuration =================================
    #
    # <Decimal input>
    #
    # Set RSSI channel measurements
    # Specify 1 - 13
    #
    #   channel < 14 = Do measure
    #   channel > 13 = Do not measure (CH number less than or equal to 255)
    #
    #--------------------------------------------------------
    # If you want to measure all from 1 to 13ch
    1
    2
    3
    4
    5
    6
    7
    8
    9
    10
    11
    12
    13
    ###############################################
    # samples
    # If you want to measure a specific channel
    ##############################################
    #1
    #13
    #77
    #77
    #77
    #77
    #77
    #77
    #77
    #77
    #77
    #77
    #77
    #END-samples----------------------------------
    #=== Access Point Test Connection settings ===
    #
    # Settings for RSSI measurement? Set of:
    #
    #   0 = Do not measure
    #   1 = Do measure
    #   2 = Measure using HW config for Eurus
    #
    # OK count
    # NG count
    #
    # Estimated measurement time per loop
    #   100msec
    #
    # <AP>
    #   SSID
    #   IP ADDRESS
    #
    # <COOKIE>
    #   IP ADDRESS
    #   NETMASK
    #   DEFAULT ROUTE
    #   PRIMARY DNS
    #
    #----------------------------------------------
    0
    10
    300
    #<AP>
    LV2DIAG-AP
    192.168.1.1
    #<COOKIE>
    192.168.1.100
    255.255.255.0
    192.168.1.1
    192.168.1.1
    #=== BT Settings ==============================
    #
    # <Decimal input>
    #
    # Settings for RSSI measurement? Set of:
    #
    #   0 = Do not measure
    #   1 = Do measure
    #
    # RSSI Standard
    #
    #   min[dBm]
    #   max[dBm]
    #
    # OK count
    # NG count
    #
    # Estimated measurement time per loop
    #   100msec
    #----------------------------------------------
    # <ANTENNA 1>
    0
    -60
    -1
    2
    300
    # <ANTENNA 2>
    0
    -60
    -1
    2
    30
    # <ANTENNA DIVERSITY>
    0
    -60
    -1
    2
    30
    #=== CS Only ================================
    #
    # LED Lighting pattern when removing the controller
    #
    # LED ID
    #
    #   1 = POWER(green)
    #   2 = STATUS(red)
    #
    # LED ACTION
    #
    #   0 = OFF
    #   1 = ON
    #   2 = BLINK FAST
    #   3 = BLINK SLOW
    #--------------------------------------------
    #<1>------
    # LED ID
    1
    # LED ACTION
    2
    #<2>------
    # LED ID
    2
    # LED ACTION
    0
    #=== Other items ===================
    # to be executed after WLAN and BT inspection
    #----------------------------------------------
    # Drive Init
    #   0 = Do not perform
    #   1 = Do perform
    #----------------------------------------------
    1
    #---------------------------------------------
    # Install Systemsoftware
    #   0 = Do not perform
    #   1 = Do perform
    #----------------------------------------------
    0
    #---------------------------------------------
    # freebdp
    #   0 = Do not perform
    #   1 = Do perform
    #----------------------------------------------
    1
    #---------------------------------------------
    # Name of file used for Install Systemsoftware
    #----------------------------------------------
    manufacturing_updater_for_reset.self

http://pastebin.com/3PwAVi6s

== ps3 80gb remarry with new logic board key chip was destroyed?? ==

I am a total noob to this type of fix but I do have electronics background. what I want to know if somebody could explain it to me in laymen's terms. what type of jigs/dongles or what do I need to remarry my new logic board with the mother board. as stated the original key chip was destroyed. I like trying to figure these type of things out but all of you talk a language that I some what understand.also I have other ps3s but this is like a challenge to see if I can do it with the help of all of you. my system is a cheche01 80gb running 4.61 or whatever the latest firmware is. so any info would be great. e-mail me at blacktopops2@gmail.com Thank you!!

You need a PSgrade/JIG, like listed here : http://www.ps3devwiki.com/wiki/Talk:Downgrading_with_PSgrade_Dongle
that will enable it into service mode on 3.55 firmware - so if it is now on 4.xx you also need a hardware flasher to first downgrade the console to 3.55.