Editing Talk:Regulators

Jump to navigation Jump to search
Warning: You are not logged in. Your IP address will be publicly visible if you make any edits. If you log in or create an account, your edits will be attributed to your username, along with other benefits.

The edit can be undone. Please check the comparison below to verify that this is what you want to do, and then publish the changes below to finish undoing the edit.

Latest revision Your text
Line 5: Line 5:
By looking at the first syscon model used by the PS3 [[CXR713120-201GB]] where we know the names of the pin signals it seems these syscon control lines for voltage regulators could be the syscon pins named SW_x or SW_x_x (switches, used as a generic name for slave components that only has 2 states)
By looking at the first syscon model used by the PS3 [[CXR713120-201GB]] where we know the names of the pin signals it seems these syscon control lines for voltage regulators could be the syscon pins named SW_x or SW_x_x (switches, used as a generic name for slave components that only has 2 states)


==== Mitsumi 463A (STBY) ====
==== Mitsumi 463A (voltage regulator) ====
<div style="float:right">[[File:Mitsumi 463A.jpg|200px|thumb|left|Mitsumi voltage regulator 463A<br />Seen on a JSD-001 motherboard]]</div>
<div style="float:right">[[File:Mitsumi 463A.jpg|200px|thumb|left|Mitsumi voltage regulator 463A<br />Seen on a JSD-001 motherboard]]</div>


Line 12: Line 12:
! Pin # !! Name !! Description
! Pin # !! Name !! Description
|-
|-
| 1 || {{cellcolors|#ff0000}} 5V_EVER || Input 5v standby rail, from power supply (pin 1 of connector CN101)
| 1 || {{cellcolors|#ff0000}} VCC/5V_EVER || From power supply 5v standby rail (pin 1 of connector CN101)
|-
|-
| 2 || {{cellcolors|#ffcc22}} 3.3V_EVER_B || Output 3.3v standby rail 2
| 2 || {{cellcolors|#ffcc22}} OUT/3.3V_EVER_B || 3.3v_standby_rail_2
|-
|-
| 3 || {{cellcolors|#33cc33|#ffffff}} RST/SYSCON_RST || Goes under package to the black 100 ohm resistor at its right, and from there to syscon pin26@[[SW2-303]]
| 3 || {{cellcolors|#33cc33|#ffffff}} EN ? || Goes under package to the black 100 ohm resistor at its right, and from there to syscon pin26@[[SW2-303]]
|-
|-
| 4 || ? || Goes under package to squared testpad/sinkhole at its right (not connected ?)
| 4 || ? || Goes under package to squared testpad/sinkhole at its right (not connected ?)
|-
|-
| 5 || {{cellcolors|#ff0000}} VCAP || Capacitor to ground
| 5 || ? || Capacitor to ground
|-
|-
| 6 || ? || To squared testpad/sinkhole at its top (not connected ?)
| 6 || ? || To squared testpad/sinkhole at its top (not connected ?)
Line 26: Line 26:
| 7 || {{cellcolors|#000000|#aaaaaa}} GND || Ground
| 7 || {{cellcolors|#000000|#aaaaaa}} GND || Ground
|-
|-
| 8 || {{cellcolors|#ffcc22}} 3.3V_EVER_A || Output 3.3v standby rail 1
| 8 || {{cellcolors|#ffcc22}} OUT/3.3V_EVER_A || 3.3v_standby_rail_1
|-
|-
|}
|}
{{clear}}
{{clear}}


==== Mitsumi 348A (HDMI) ====
==== Mitsumi 348A (voltage regulator) ====
<div style="float:right">[[File:Mitsumi 348A.jpg|200px|thumb|left|Mitsumi voltage regulator 348A<br />Seen on a JSD-001 motherboard]]</div>
<div style="float:right">[[File:Mitsumi 348A.jpg|200px|thumb|left|Mitsumi voltage regulator 348A<br />Seen on a JSD-001 motherboard]]</div>
*Part No: '''Mitsumi MM3348'''
*Datasheet: https://www.mitsumi.co.jp/latest/Catalog/pdf/regulate_mm_3348_e.pdf


{| border="1" cellspacing="0" cellpadding="5" border="#999" class="wikitable" style="border:1px solid #999; border-collapse: collapse;"  
{| border="1" cellspacing="0" cellpadding="5" border="#999" class="wikitable" style="border:1px solid #999; border-collapse: collapse;"  
Line 40: Line 38:
! Pin # !! Name !! Description
! Pin # !! Name !! Description
|-
|-
| 1 || {{cellcolors|#ddd}} N/C || Not connected
| 1 || ? || Not connected ?
|-
|-
| 2 || {{cellcolors|#33cc33|#ffffff}} HDMI_EN || Connected to [[Template:Syscon_pinout_LQFP_128_pins|SW2-30x]] pin 119<br>Connected to [[HDMI]] [[Connectors#HDMI_Out|connector]] pin 18 (+5V output) through a <abbr title="Labeled AROKE, located next to the HDMI connector, it have a thick copper trace for a voltage of the HDMI connector)>transistor</abbr>
| 2 || {{cellcolors|#33cc33|#ffffff}} EN_HDMI ? || Connected to syscon pin118@[[SW2-303]]
|-
|-
| 3 || {{cellcolors|#000000|#aaaaaa}} GND || Ground (this pin also dissipates heat to the circuit board ground layer)
| 3 || {{cellcolors|#000000|#aaaaaa}} GND || Ground
|-
|-
| 4 || {{cellcolors|#ffcc22}} HDMI_VCC1 / +5V_ANA ? || Connected to [[HDMI]] controller [[MN8647091]] pin 100 (and a lot more pins). It have a testpad at the other board side
| 4 || {{cellcolors|#ffcc22}} OUT1/HDMI ? || output voltage rail 1 ?. Connected to pin 100 (and other 10 pins more) of HDMI controller. It has a testpad at the other side
|-
|-
| 5 || {{cellcolors|#ffcc22}} HDMI_VCC2 / +3.3V_ANA ? || Connected to [[HDMI]] controller [[MN8647091]] pin 25 (and a lot more pins). It have a testpad at the other board side
| 5 || {{cellcolors|#ffcc22}} OUT2/AV ? || output voltage rail 2 for A/V controller and optical ? (not tested). It has a testpad at the other side
|-
|-
| 6 || {{cellcolors|#000000|#aaaaaa}} GND || Ground (this pin also dissipates heat to the circuit board ground layer)
| 6 || {{cellcolors|#000000|#aaaaaa}} GND || Ground
|-
|-
| 7 || {{cellcolors|#33cc33|#ffffff}} HDMI_EN || Connected to [[Template:Syscon_pinout_LQFP_128_pins|SW2-30x]] pin 119<br>Connected to [[HDMI]] [[Connectors#HDMI_Out|connector]] pin 18 (+5V output) through a <abbr title="Labeled AROKE, located next to the HDMI connector, it have a thick copper trace for a voltage of the HDMI connector)>transistor</abbr>
| 7 || {{cellcolors|#33cc33|#ffffff}} EN_AV ? || Connected to syscon pin119@[[SW2-303]]
|-
|-
| 8 || {{cellcolors|#ff0000}} 5V_EVER || Connected to [[Power Supply]] control connector (CN101) pin 1
| 8 || {{cellcolors|#ff0000}} VCC/5V_EVER || From power supply 5v standby rail (pin 1 of connector CN101)
|-
|-
|}
|}
{{clear}}
{{clear}}


==== Mitsumi 810X (RSX RAM) ====
==== Mitsumi 040 810X (close to RSX) ====
<div style="float:right">[[File:Mitsumi 810x.jpg|200px|thumb|left|Mitsumi voltage regulator 810x]]</div>
*Part No: '''Mitsumi MM1810XFBE'''
*Datasheet: <abbr title="Missing In Action>M.I.A.</abbr>. Pinout similar than https://www.mitsumi.co.jp/latest/Catalog/pdf/regulate_mm_185x_e.pdf (page 4)


{| border="1" cellspacing="0" cellpadding="5" border="#999" class="wikitable" style="border:1px solid #999; border-collapse: collapse;"  
{| border="1" cellspacing="0" cellpadding="5" border="#999" class="wikitable" style="border:1px solid #999; border-collapse: collapse;"  
Line 68: Line 63:
! Pin # !! Name !! Description
! Pin # !! Name !! Description
|-
|-
| 1 || {{cellcolors|#ffcc22}} RSX_VDDR || connected to a lot of pads of the [[RSX]], it has a testpad at the other board side
| 1 || ? || connected to 4x sinkholes (it has a testpad at the other side)
|-
|-
| 2 || {{cellcolors|#ddd}} N/C || Not connected
| 2 || ? || hidden under package
|-
|-
| 3 || {{cellcolors|#000000|#aaaaaa}} GND || Ground
| 3 || {{cellcolors|#000000|#aaaaaa}} GND || Ground
|-
|-
| 4 || {{cellcolors|#ff0000}} NOISE_CAP || Noise decrease pin. 0.01μF capacitor to GND, and to a tiny squared testpad
| 4 || ? ||  
|-
|-
| 5 || {{cellcolors|#33cc33|#ffffff}} EN ?/Cont/Control || Connected to syscon pin75@[[SW2-303]]
| 5 || {{cellcolors|#33cc33|#ffffff}} EN ? || Connected to syscon pin75@[[SW2-303]]
|-
|-
| 6 || {{cellcolors|#ddd}} N/C || Not connected
| 6 || ? || hidden under package
|-
|-
| 7 || {{cellcolors|#ddd}} N/C || Not connected
| 7 || ? || hidden under package
|-
|-
| 8 || {{cellcolors|#ff0000}} VIN || connected to 2x sinkholes
| 8 || ? || connected to 2x sinkholes
|-
|-
|}
|}
Line 102: Line 97:
| 4 || ? || Capacitor to ground
| 4 || ? || Capacitor to ground
|-
|-
| 5 || {{cellcolors|#33cc33|#ffffff}} EN ? || Connected to pin50@[[SW2-303]]. And pin 3 @ Service Connector
| 5 || {{cellcolors|#33cc33|#ffffff}} EN ? || Connected to pin50@[[SW2-303]]
|-
|-
| 6 || {{cellcolors|#000000|#aaaaaa}} GND ||  
| 6 || {{cellcolors|#000000|#aaaaaa}} GND ||  
Line 303: Line 298:
| 20
| 20
|}
|}
== Others ==
*RSX VDDR control in DIA-001 ---> Rohm D35231 (1,2v)?, see [https://www.psx-place.com/threads/fault-finding-ylod-with-the-syscon-first-steps-and-error-reporting.30100/page-134#post-327399 1]
*RSX VDDR control in DIA-002 ---> Rohm D35230 (1,0v)?, see [https://www.psx-place.com/threads/fault-finding-ylod-with-the-syscon-first-steps-and-error-reporting.30100/page-134#post-327399 1]
Please note that all contributions to PS3 Developer wiki are considered to be released under the GNU Free Documentation License 1.2 (see PS3 Developer wiki:Copyrights for details). If you do not want your writing to be edited mercilessly and redistributed at will, then do not submit it here.
You are also promising us that you wrote this yourself, or copied it from a public domain or similar free resource. Do not submit copyrighted work without permission!

To protect the wiki against automated edit spam, we kindly ask you to solve the following hCaptcha:

Cancel Editing help (opens in new window)

Templates used on this page: